WIRELESS HEADSET
Drive SafeDrive Safe About noise cancellation technologyAbout noise cancellation technology
CAUTION: Although this device enables drivers to
conduct handsfree conversations, it is still safer to pull
over before using a mobile phone.
Always keep your full attention on your driving.
Driving while talking on your mobile phone is dangerous, and
illegal in many states.
Check local laws regarding the use of a mobile handset and wireless
headset while driving. If you use the Bluetooth Headset while
driving, ensure your attention and focus remains on your driving.
This headset uses a dual microphone design to lter out wind
and unwanted external noise.
Using Noise Cancellation Technology, the headset compares the
sound from the twin, built-in microphones, and is able to recognize
the dierence between voice and unwanted background noise.
Noise cancel
microphone 1
Please use your mobile phone, and our
product responsibly while driving!
Location of controlsLocation of controls
Manual Pairing
1. Make sure the Bluetooth Headset is within 3 feet of your
mobile phone or Bluetooth enabled device.
2. Set the [Power] switch to the ON position.
3. Press and HOLD the [Call] button until the indicator light
ashes RED and BLUE alternately.
4. The headset is now in Pairing Mode and is ready to connect
to your mobile phone or Bluetooth enabled device.
Power Switch
Power ON/OFF
(Green = ON, Red = OFF)
within 3 feet
OR depending on which model mobile phone you are trying
to connect the headset to, it may not be necessary to enter a
passcode and the following message (or similar) may appear on
your phone’s display.
Bluetooth: Enabled
Paired Devices:
EM529
“EM529” would like to pair
with your phone. Would you
like to allow it to pair?
Cancel Pair
Select “Pair” to complete the pairing process.
Power Switch
Power ON/OFF
(Green = ON, Red = OFF)
Noise cancel
microphone 1
Call button
Answer/end a call
Indicator
light
Owner’s Manual
Model: EM529S
Charging
socket
Noise cancel
microphone 2
In the boxIn the boxIn the boxIn the boxIn the box Charging the headsetCharging the headset
NOTE: Charge the headset for at least 8 hours before using it
for the rst time, even if the RED LED indicator shuts o.
WIRELESS HEADSET
1. Connect the small end of the USB cable to the charging
socket of the headset.
2. Connect the other end of the USB cable to either the:
• AC Charger, and plug into a wall (A/C) outlet
• Computer’s USB port
• Car Charger
3. The RED LED indicator light turns on while the headset is
charging.
4. The RED LED indicator light shuts o when the headset is
fully charged (approximately 2-3 hours).
NOTE: When the battery is running low, the RED LED indicator
light starts to ash along with a warning beep.
Bluetooth
Headset
S M L
Silicone cushions
Owner’s Manual
Model: EM529S
Owner’s
Manual
Speaker/
Silicone cushion
Volume Up
Volume Down
Microphone
Noise cancel
microphone 2
Noise Cancellation Technology
Enables the other end of your
conversation to hear you clearly!
Pairing the headsetPairing the headset
Easy Pairing
(First time pairing only)
Please read through this section before turning the device on.
We recommend reading this manual in it’s entirety before
pairing the headset for the rst time.
This Bluetooth headset has an “Easy Pairing” feature which sets
the headset to Pairing Mode the rst time the power switch
is turned on.
1. Make sure the Bluetooth Headset is within 3 feet of our
mobile phone or Bluetooth enabled device.
within 3 feet
Indicator light
Red and Blue ashing
Indicator light
Red and Blue ashing
NOTE: To enter Pairing Mode at any time, you must press and
HOLD the [Call] button for approximately 10 seconds.
Continue here from “Easy Pairing”
5. Set your mobile phone to search for Bluetooth devices.
Bluetooth: Enabled
Paired Devices:
*Empty *
Searching for devices
ound
1 f
Stop
6. When the phone nds the headset, conrm by selecting
EM529 from the list.
Bluetooth: Enabled
Paired Devices:
EM529
Select Device:
EM529
Cancel
8. Your mobile phone will conrm that the pairing process was
completed and prompt you to accept the connection.
Please select “YE S” to connect the headset to your mobile
phone. If the pairing was successful, the headset’s blue
indicator light turns to standby mode and ashes once
every three seconds.
Bluetooth: Enabled
Paired Devices:
EM529
Confirm connection to
EM529?
YES NO
/
9. When attempting to reconnect the headset to your mobile
phone, you may see the message below and your mobile
phone will prompt you to accept the connection request to
the EM529 headset, and an option not to ask this again.
Please accept the connection, and if you select “Don’t ask this
again”, your phone will automatically accept future connection
requests from the headset.
Bluetooth: Enabled
Paired Devices:
EM529
Accept connection request
from EM529?
YES NO
/
Don’t ask this again
Earhook
Stereo earphone
USB charging
cable
AC charger
Car Charger
USB cable
AC Charger
Charging
Socket
Headset
Car ChargerPC
Indicator
light
Power Switch
Power ON/OFF
(Green = ON, Red = OFF)
2. Set the [Power] switch to the ON position. The indicator
light should be ashing RED and BLUE alternately, indicating
the headset is in Pairing Mode and ready to connect to your
Bluetooth enabled device.
3. Continue to “Manual Pairing” step 5 shown in the next column.
NOTE: Manual Pairing
If the rst time pairing was unsuccessful or for future pairing,
you will need to manually pair the headset to your Bluetooth
enabled device (see “Manual Pairing” step 1 in the next column ).
7. Enter the passcode “0000” when prompted by the phone.
Bluetooth: Enabled
Paired Devices:
EM529
Enter numeric passkey
for EM529:
0000
OK
NOTE: The screenshots above are typical of many Bluetooth
enabled phones in the market today, and are used to
assist in the explanation of the pairing process. Your
mobile phone’s or Bluetooth enabled device’s interface
and interaction with the headset may be slightly
dierent from the illustrations shown.
Using the headsetUsing the headset
NOTE: When the [Power] switch is set to the ON position for
the rst time, the headset will be in Pairing Mode (the
indicator light will be ashing RED and BLUE alternately),
please refer to “Easy Pairing”.
Powering ON/OFF
• To turn ON, set the [Power] switch to the ON position (green).
The blue indicator light will ash intermittently.
Power Switch
Power ON
(Green)
• To turn OFF, slide the [Power] switch to the OFF position (red).
The indicator light will ash RED before the headset shuts
o.
Power Switch
Power OFF
(Red)
Answering / Ending a call
• To answer a call, press and release the [Call] button or press
the answer key on your mobile phone.
• To end a call, press and release the [Call] button or press the
end key on your mobile phone.
Call button
Answer/end a call
Rejecting a call
During an incoming call press and HOLD the [Call] button
for 3 seconds or until you hear a conrmation beep.
Making a call
Dial the number and press the send button on your mobile
phone, the call is automatically transferred to the headset.
Redialing the last number called
(Dependent on your phone supporting this feature)
Press the [Call] button twice. The last number called will be
redialed.
Call button
Press twice to redial
Indicator light
Indicator light
Volume
To adjust the in-call volume, press the [Volume Up] or [Volume
Down] button.
Volume Up
Volume Down
NOTE: You may also adjust the volume from your mobile phone’s
volume control.
Mute
Press the [Volume Up] and the [Volume Down] button
simultaneously until you hear a beep, repeat to unmute the call.
Volume Up
Volume Down
Press simultaneously
to mute and unmute
Wearing your Bluetooth HeadsetWearing your Bluetooth Headset
For added comfort and noise suppression, 3 silicone cushions
are included with the headset. Choose the silicone cushion (S)
(M) (L) which ts most comfortably in your ear and insert it on
the headset as shown in the diagram below.
S M L
Silicone cushions
You may wear the headset with or without the provided earhook.
If you choose to use the earhook, connect it to the headset as
shown in the diagram below.
Earhook
Right earLeft ear
NOTE: For the best audio quality, always wear the headset on
the same side of your body as your mobile phone.
Stereo BluetoothStereo Bluetooth
Connect the Stereo earphone to the Bluetooth Headset’s charging
socket as shown below.
Stereo
earphone
Charging
socket
Insert the Bluetooth Headset in one ear, and wrap the Stereo
Earphone behind your neck and insert it into your other ear.
This headset allows you to listen (in full stereo) and control* the
music and video on your Bluetooth enabled mobile phone,
gaming console, computer or mp3 player and supports the
following Bluetooth proles:
•
•
•
•
To use the headphones to listen to and control music and video,
your Bluetooth enabled device must support the A2DP and AVRCP
proles. Please refer to the user guide of your Bluetooth enabled
device for more information.
A2DP - Advanced Audio Distribution Prole
AVRCP - Audio/Video Remote Control Prole
HSP - Headset Prole
HFP - Handsfree Prole
Playing music and videoPlaying music and video
To enjoy music and video using your Bluetooth Headset,
press the [Play] button of your Bluetooth enabled device to
begin music playback. Once playback has begun, you can
control the music and videos, or answer phone calls from
the control buttons of the Bluetooth Headset (Not all mobile
phones support the control of music using Bluetooth).
Adjusting the volume
Press the [Volume Up] or [Volume Down] button to adjust the
volume to the desired level.
NOTE: You may also adjust the volume from your mobile phone’s
volume control.
Play/Pause* (music and video)
While the music or video is playing, press the [Call] button to
pause. To resume playback, press the [Call] button again.
Skipping or searching* (music or video)
While the music or video is playing, press and HOLD the
[Volume Up] button to go to the previous song, or press and
HOLD the [Volume Down] button to go to the next song.
Answering a call while media is playing
During an incoming call, press the [Call] button to answer.
Press the [Call] button again to end the call and return to media
playback.
Call button
Play/Pause
Volume Up
(
Press and HOLD
Previous song
Volume Down
(
Press and HOLD
Next song
*Certain Bluetooth features including those listed may not
be supported by all compatible Bluetooth-enabled devices,
and/or the functionality of such features may be limited in
certain devices.
)
)
Troubleshooting tipsTroubleshooting tips
I cannot get the headset into Pairing Mode
Make sure the headset is turned on before beginning the
•
pairing process (the headset is in pairing mode when you
turn it on for the rst time).
If you are not pairing for the rst time or for manual pairing,
•
press and HOLD the [Call] button until the indicator light
ashes RED and BLUE alternately.
My mobile phone cannot pair with the headset
Make sure that you fully charged the headset before pairing.
•
Keep the headset and mobile phone within 3 feet of each
•
other during the pairing process.
Check that your phone’s Bluetooth feature is turned ON.
•
• Try removing the battery from your mobile phone for 5 minutes.
Place the battery back in the phone, power it on, and retry the
pairing process (see “Manual Pairing”).
Try repeating the pairing process, see “Manual pairing.”
•
After successfully pairing my mobile phone
and headset, when I shut the phone and
turn it on again, the headset did not
automatically reconnect
Try turning the headset OFF, and then turning it ON again.
•
Many mobile phones have an auto reconnect option when rst
•
attempting to reconnect to a newly paired Bluetooth device.
Make sure you accept this option, so that the headset
automatically reconnects to your mobile phone; check the user
guide of your mobile phone for more information regarding
this option.
Try unpairing the headset from your phone, and repeat the
•
pairing procedure.
I hear distortion, and the sound quality is
poor
For the best audio quality, always wear the headset on the same
•
side of the body as your mobile phone.
Check that the battery is charged enough.
•
The sound is very low
Try adjusting the volume by using the [Volume Up] or
•
[Volume Down] button on the headset; make sure the
volume on your mobile phone is turned up as well.
FCC and telephone company informationFCC and telephone company information
FCC Part 15
This equipment has been tested and found to comply with the
requirements for a Class B digital device under Part 15 of the
Federal Communications Commission (FCC) rules. These
requirements are intended to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Do not attempt to repair or modify this equipment.
Warning: Changes or modications to this equipment not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Industry CanadaIndustry Canada
Operation is subject to the following two conditions: (1) This
device may not cause interference and (2) This device must
accept any interference, including interference that may
cause undesired operation of the device.
The term “IC:” before the certication/registration number
only signies that registration was performed based on a
Declaration of Conformity indicating that Industry Canada
technical specications were met. It does not imply that
Industry Canada approved the equipment.
Warranty informationWarranty information
Limited Warranty
In the unlikely event that this product is defective, or does
not perform properly, you may within one (1) year from your
original date of purchase return it to the authorized service
center for repair or exchange.
TO OBTAIN WARRANTY SERVICE:
• Provide proof of the date of purchase within the package
(Dated bill of sale).
• Prepay all shipping costs to the authorized service center,
and remember to insure your return.
• Include a return shipping address (no P.O. Boxes),
a telephone contact number, and the defective unit within
the package.
• Describe the defect or reason you are returning the product.
Your product will be repaired or replaced, at our option, for the same
or similar model of equal value if examination by the service center
determines this product is defective. Products received damaged
as a result of shipping will require you to le a claim with the carrier.
The shipping address of the authorized service center is:
Southern Telecom, Inc.
ATTN: Customer Service - 2nd Floor
14-C 53rd Street
Brooklyn, NY 11232
Should you have any questions or problems concerning this
product, please contact our customer service department at:
1-877-768-8483 (Toll Free)
Monday - Thursday: 9AM - 5PM (EST)
Friday: 9AM - 3PM (EST)
or
via e-mail at
cs@southerntelecom.com
Warranty service not provided
This warranty does not cover damage resulting from accident,
misuse, abuse, improper installation or operation, lack of reasonable
care, and unauthorized modication. This warranty is voided in
the event any unauthorized person opens, alters or repairs this
product. All products being returned to the authorized service
center for repair must be suitably packaged.
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY
APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE
HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION
GIVEN BY SOUTHERN TELECOM INC. IT’S AGENTS, OR EMPLOYEES
SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE
SCOPE OF THIS WARRANTY.
• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY
IS THE EXCLUSIVE REMEDY OF THE CONSUMER. SOUTHERN
TELECOM INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS
OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER
OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED
BY THE LAWS OF THE STATE OF NEW YORK. EXCEPT TO THE
EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO
THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion nor limitation of incidental
or consequential damages, or limitations on how long an implied
warranty lasts so the above limitations or exclusions may not apply
to you. This warranty gives you specic legal rights, and you
also may have other rights that vary from state to state.
www.emersonphones.com
Distributed by Southern Telecom Inc. Brooklyn, NY 11232
© 2011 Southern Telecom Inc. All rights reserved.
Emerson and the G-Clef logo are registered trademarks of
Emerson Radio Corp. Parsippany, New Jersey USA.
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc.
SONY PlayStatiion® & PS3™ are either trademarks or registered
trademarks of SONY.
All other trademarks are trademarks of their respective owners.
Loading...