Emerson EM-262 User Manual

O Owner's Manual O Location of controls
Power button
Power ON/OFF
Answer/end
TM
Indicator light
Charging

Charging the Bluetooth Headset

Before using your Bluetooth Headset for the first time, charge it for 10-12 hours.
1. Connect the smaller end of the USB cable to the charging socket of the headset.
2. Connect the other end of the USB cable to either the:
• AC Charger, and plug into a wall (A/C) outlet.
• Computer's USB port.
• Car Charger
3. The BLUE LED indicator light turns on.
4. The BLUE LED indicator light shuts off when the headset is fully charged (approximately 2-3 hours).
©Bluetooth'*
NOTE: The Bluetooth Headset will emit an intermittent
beep tone when the battery is running low and requires recharging.
Wireless Headset
Model: EM262

^ In the box

NOTE: Make sure you charge your headset for 10-12 hours
before using it for the first time.
^ Pairing the heaebetwith a Bluetooth enabled phone
1. Make sure the Bluetooth Headset is turned off.
2. Keep your Bluetooth Headset and mobile phone within 3 feet of each other during the pairing process.
3. Press and HOLD the [POWER] button until the BLUE indicator
light turns on, flashes several times, and becomes a steady
blue. The headset is now in Pairing Mode, and is ready to connect to your mobile phone.

8a About noise cancellation technology

Using Noise Cancellation technology, the headset compares
the sound from the twin built-in microphones, and is able to
recognize the difference between voice and unwanted background noise. ^ ^ .
Microphone 2
Dual Microphone Design
Wind and unwanted bacl^round noise
are filtered out enabling the other end of
your conversation to hear you clearlyl
Microphone 1
NOTE: To enter the Pairing Mode,you must press and HOLD the
power button for approximately 10 seconds.
Volume up
Microphone 2 ^Microphone 1
Power button
(Press & HOLD)
Indicator light
within 3 feet
Volume down
4. Set your mobile phone to search for Bluetooth devices.
Bluetooth: Enabled
Paired Devices:
© Searching for devices
5. When the phone finds the headset, confirm by selecting it from the list.
Bluetxioth: Enabled
Paired Devices:
6. Enter passcode"0000"when prompted by the phone.
Bluetooth: Enabled
Paired Devices:
Q
NOTE: If your mobile phone is Bluetooth 2.1 compliant, you will
not need to enter a passcode, and can skip to step 7.
7. Your mobile phone will confirm that the pairing was completed, and prompt you to accept the connection. Please respond
YES to connect the headset to your mobile phone. If the pain ng
was successful, the headset's indicator light flashes a steady blue.
Bluetooth: Enabled
Paired Devices:
0
8. When attempting to reconnect the headset to your mobile phone,you may see the message below, and your mobile phone will prompt you to accept the connection request to the EM262 headset, and an option not to ask this again. Please accept the connection,and if you select"Don't ask this
again" your phone will automatically accept future connection requests from your Bluetooth Headset.
Bluetooth: Enabled
Paired Devices:
0
B Don't ask this again
NOTE: The screenshots above are typical of many Bluetooth enabled
phones in the market today, and are used to assist in the explanation of the pairing process. Your mobile phone's
interface and interaction with the Bluetooth Headset may slightly differ from the illustrations above.
‘Empty ’
Enter numeric passkey for EM262:
OK
Confirm connection to EM2B2?
YES I/
Accept connection request from EM2B2?
YES
/

8M Using your Bluetooth Headset

Powering ON/OFF
• To turn ON, press and HOLD the [POWER] button until the
BLUE LED indicator light turns on.
• To turn OFF, press and HOLD the [POWER] button until the
BLUE LED indicator light flashes quickly several times, and
then turns off.
Power button
(Press & HOLD)
Indicator light
Answering/Ending a call
• To answer a call, press and release the [POWER] button.
• To end a call, press and release the [POWER] button.
Power button
To make a call
Dial the number and press the send button on your mobile phone, the call is automatically transferred to the headset.
Redialing the iast number caiied (Dependent on your phone supporting this feature)
Double press the [POWER] button and release. The headset will emit a confirmation beep tone, and the last number called will be redialed.
Power Button
Double Press to redial
Adjusting the voiume
Press the [VOLUME UP] or [VOLUME DOWN] button to adjust the volume to the desired level.
Volume up
NOTE: You may also adjust the volume from your mobile phone's
volume control.

8M Wearing your Bluetooth Headset

You may wear your headset with or without the provided earhook. If you choose to wear your headset with the earhook, connect it to the headset as shown in the diagram below.
Earhook
comfortably
Headset on the same side ofthe body as your mobile phone

8Ba Troubleshooting tips

I cannot get the Bluetooth Headset into Pairing Mode
• Make sure the Bluetooth Headset is turned off before
beginning the pairing process.
• Press and HOLD the [POWER] button until the BLUE
indicator light turns on,flashes several times, and becomes a steady blue. This will signal that the headset is in Pairing
Mode,and ready to connect to your mobile phone.
Mymobile phone is not able to pairwith the Bluetooth Headset
• Make sure that you fully charged the headset before pairing.
• Keep your Bluetooth Headset and mobile phone within 3
feet of each other during the pairing process.
• Check that your phone's Bluetooth feature is turned ON.
• Try repeating the pairing process, see "Pairing the headset with a Bluetooth enabled phone."
© After successfully pairing my mobile phone and Bluetooth
Headset, when I shut my phone and turn it on again, my
^ headset did not automatically connect_____________________y
' Try turning the headset OFF, and then turning it ON again.
' Many mobile phones have an auto reconnect option when first
attempting to reconnect to a newly paired Bluetooth device. Make sure you accept this option, so that your Bluetooth Headset
automatically reconnects to your mobile phone; check the user guide of your mobile phone for more information regarding this option.
' Try unpairing the headset from your phon^and repeat the pa i ri ng
procedure
I hear distortion, and the sound quality is poor
For the best audio quality, always wear your Bluetooth Headset
on the same side of the body as your mobile phone.
Check that the battery is charged enough.
^^The sound is very low
Try adjusting the volume by using the [Volume] button on your
headset; make sure the volume on your mobile phone is
turned up as well.
1

Drive Safe

Driving while talking on your mobile phone is dangerous,and illegal in many states. Although this device enables drivers to conduct handsfree conversations, it is still dangerous to drive and use a mobile phone at the same time. We recommend pulling over before making or answering calls, especially during adverse driving conditions. Please use your mobile phone,and our product responsibly while driving!

8Bd Safety information

Check local laws regarding use of a mobile handset and wireless
headset while driving. If you use the Bluetooth Headset while drivi ng, ensure your attention and focus remains on your driving.
* Observe all signs in the designated areas where some electronic
devices or RF radio products are required to be switched off. These could include airplanes, hospitals,blasting areas,and potentially explosive atmospheres.
CAUTION: Although this device enables drivers to
conduct handsfree conversations, it is still dangerous to drive and use a mobile phone at the same time.
A
Always keep your full attention on your driving.
1^ Product maintenance
• Power off this product when not in use.
• DO NOT expose this product to water or other liquids.
• DONOTuseabrasivedeaningsolventstodeantheBluetoothHeadset
• If you will not use the Bluetooth Headset for long periods^ be sure to
store it in a dry plac^fieefiom extreme temperature humidity and dust

FCC and telephone company information

FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more ofthe following measures:
• Re-orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Do not attempt to repair or modify this equipment. Warning: Changes or modifications to this equipment not
expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

8Ba Industry Canada

Operation is subject to the following two conditions: (1) This device may not cause interference and (2) This device must accept any interference, including interference that may cause undesired operation ofthe device.
The term "1C:" before the certification/registration number only signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.

8M Warranty information

Limited Warranty

In the unlikely event that this product is defective, or does
not perform properly, you may within one (1) year from your original date of purchase return it to the authorized service center for repair or exchange.
TO OBTAIN WARRANTY SERVICE:
• Provide proof of the date of purchase within the package
(Dated bili of saie).
• Prepay aii shipping costs to the authorized service center,
and remember to insure your return.
• Include a return shipping address (no P.O. Boxes),
a telephone contact number, and the defective unit within the package.
• Describe the defect or reason you are returning the product
Your product will be repaired or replaced, at our option, for the same or similar model of equal value if examination by the sen/ice center determines this product is defective. Products received damaged as a result of shipping will require you to file a claim with the carrier.
The shipping address ofthe authorized service center is:
^ Southern Telecom Inc.
ATTN: Returns Department
14-C 53rd Street Brooklyn, NY 11232
Should you have any questions or problems concerning this product, please contact our customer service department at:
01-877-768-8483 (Toll Free)
Monday - Thursday: 9AM - 5PM (EST)
Friday: 9AM-3PM (EST)
or
via e-maii at
Q cs@southernteiecom.com
Warranty service not provided
This warranty does not cover damage resulting from accident,
misuse, abuse, improper installation or operation, lack of reasonable care, and unauthorized modification. This warranty is voided in the event any unauthorized person opens, alters or repairs this
product. All products being returned to the authorized service center for repair must be suitably packaged.
Limitation of Warranty:
• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY
APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY SOLITHERN TELECOM INC. ITS AGENTS, OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY.
• REPAIROR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY
IS THE EXCLUSIVE REMEDY OF THE CONSUMER. SOUTHERN TELECOM INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED
BY THE LAWS OF THE STATE OF NEW YORK. EXCEPT TO THE
EXTENT PROHIBFTED BYAPPUCABLE LAW, ANYIMPUEDWARRANTY OF MERCHANTABILFTY OR FTTNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY
PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you also may
have other rights that vary from state to state.
Distributed by: AIT Inc. Brooklyn, NY 11232
© 2009 AIT Inc. All rights reserved.
www.emersonphones.com
Emerson and the G-Clef logo are registered trademarks of
Emerson Radio Corp. Parsippany, New Jersey USA.
Tire Bluetooth^’v\/ord markand logos are owned by the Bluetooth SIG, Inc
Loading...