EATC08RE1
EATC12RE2
EATC10RE1
EATC10RE2
EATC12RE1
EATE12RD2
EATC14RD2
EATH14RD2
Handling the remote controller
CONTENTS
Handling the remote controller ......................................................
Remote controller Specifications...................................................
Function buttons .................. ..........................................................
How to use the buttons ...................................................................
Auto operation.............................................................................................................
Cooling/Heating/Fan operation..................................................................................
Dehumidifying operation ...........................................................................................
Timer operation .........................................................................................................
Energy saving operation ...........................................................................................
WARNING:
Chemical Burn Hazard. Keep batteries away from children.
This product contains a lithium button/coin cell battery. If a new or
used lithium button/coin cell battery is swallowed or enters the body,
it can cause severe internal burns and can lead to death in as little as
2 hours. Always completely secure the battery compartment. If the
battery compartment does not close securely, stop using the product,
remove the batteries, and keep it away from children. If you think
batteries might have been swallowed or placed inside any part of the
body, seek immediate medical attention.
The cells shall be disposed of properly, including keeping them away
from children. Even used cells may cause injury.
TEMP/TIMER TEMP/TIMER
ESnaevregry ESnaevregry
SleepSleep
CFhiletecrkCFhiletecrk
TEMP/TIMER TEMP/TIMER
FoMlleow FoMlleow
AutoAuto
onon
offoff
CoolCool
AutoAuto
ModeMode
DryDry
HighHigh
FanFan
On/off On/off
TimerTimer
HeatHeat
FanFan
Med Med
LowLow
2
3
4
5m
Location of the remote controller.
Use the remote controller within a distance of 5
meters from the appliance, pointing it towards
the receiver. Reception is confirmed by a beep.
5
5
5
6
7
9
CAUTIONS
The air conditioner will not operate if curtains, doors or other materials block
the signals from the remote controller to the unit.
Prevent any liquid from falling into the remote controller. Do not expose the
remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct sunlight,
the air conditioner may not function properly. Use curtains to prevent the
sunlight from falling on the receiver.
If other electrical appliances react to the remote controller, either move these
appliances or consult your local dealer.
Installation instructions of battery
Step 1: Insert a coin vertically in the groove
on the battery cover, clockwise rotation of 45
degrees, make sure that the groove is aligned
with the "unlock" sign as shown below
and remove the battery cover.
Coin
Battery cover
Groove
Lock sign
Unlock sign
Coin
Groove
Lock sign
Unlock sign
Battery cover
Step 2: Install battery inside the remote
controller, the positive (+) side up.
Battery
Positive (+) side up
Step 3: Install the battery cover, make
sure the battery cover groove is aligned
with the "unlock" sign. Insert a coin
vertically in the groove and press it
gently, then counter clockwise rotation
of 45 degrees, make sure the groove is
aligned with the "lock" sign as shown
below.
Coin
1. Battery must be disposed of properly. Do not
short circuit or dispose of in the fire.
2. Keep batteries out of the reach of children.
3. Caution for ingestion.
4. Non-rechargeable batteries are not to be
recharged.
5. Exhausted batteries are to be removed from
the product.
Lock sign
Unlock sign
Battery cover
Groove
WARNING
Coin
Lock sign
Groove
Unlock sign
Battery cover
11
22
Remote Controller Specifications
Model
Rated Voltage
Lowest Voltage of
CPU Emitting Signal
Signal Receiving Range
Environment
RG15A(B)/E,
3.0V( Lithium battery CR2025)
2.4V
5m
OOO O
-5 C~60 C(23 F~140 F)
RG15A3(B)/E,
RG15A4(B)/E, RG15A5(B)/E,
Function buttons
ON/OFF button
Operation starts when this button is
pressed and stops when the button
is pressed again.
NOTE: If the unit has ENERGY
SAVER function, it wil l ini tia te
a utomatically the Energy Saver
function under C ool, Dry, and
Auto(only Au to-Cooling and
Auto-Fan) modes.
MODE button
Press this button to
select the desired
operation mode.
NOTE:
-Buttons design is based on typical model and might be slightly different
from the actual one you purchased, the actual shape shall prevail.
-All the functions described are accomplished by the unit, if the unit has
no this feature, there is no corresponding operation happened when
press the relative button on the remote controller.
-When there are wide differences between Remote controller Illustration
and USERS MANUAL on function description, the description on USERS
MANUAL shall prevail.
RG15A(B)/E RG15A3(B)/E
RG15A4(B)/E
RG15A5(B)/E
TEMP DOWN button
Push this button to
decrease the indoor
temperature setting.
TIMER button
Push this button to
activate the uto
Start or uto Stop
""A "
"A
program.
ONE TOUCH button
Push this button, the
system will automatically
shift to COOL operation
with auto fan speed, the
setting temperature is
OO
26 C/80 F. And the timer
setting program will be
cancelled.(on some models)
ENERGY SAVER button
Press this button to
activate the Energysaving mode. Press
it again to stop the
funtion.(on some
models)
TEMP UP button
Push this button to
increase the temperature setting.
FAN button
Used to select the
desired fan speed.
SLEEP button
Press this button to
activate the Sleep
mode. This function is
available on COOL,
HEAT or AUTO mode
only and maintain the
most comfortable
temperature for you
and save enrgy. For
the detail, see sleep
operation in
,,
,
USER S MANUAL.
,,
,,
,,
33 44
How to use the buttons
1
2
Auto operation
1
2
Ensure the unit is plugged in and power is
3
available.
3
3
1.
Press the ON/OFFbutton to start the air
conditioner.
2.
Press the MODE button to select Auto.
Dehumidifying operation
Ensure the unit is plugged in and power is
available.
1.
Press the ON/OFFbutton to start the air
conditioner.
3
Press the MODE button to select Dry.
2.
3. Press the TEMP UP/DOWN button to
set the desired temperature.
3. Press the TEMP UP/DOWN button to set
the desired temperature.
NOTE
In the Dehumidifying mode, you can not switch the
NOTE
1. In the Auto mode, the air conditioner can logically
choose the mode of Cooling, Fan, Heating and
by sensing the difference between the actual
ambient room temperature and the set temperature
on the remote controller.
2. In the Auto mode, you can not switch the fan speed.
It has already been automatically controlled.
3. If the Auto mode is not comfortable for you , the
desired mode can be selected manually.
fan speed. It has already been automatically
controlled.
Cooling /Heating/ operationFan
1
3
2
3
4
Ensure the unit is plugged in and power is
available.
Press the ON/OFF button to start the air
1.
conditioner.
2.
Press the MODE button to select Cool, Heat
(cooling&heating models only) or mode.
Fan
3. Press the TEMP UP/DOWN button to set the
desired temperature.
4. Press the FAN button to select the fan
speed.
NOTE
In the Fan mode, you are not able to control the
room temperature either. In this case, only step 1, 2
and 4 may be performed.
55 66
Timer operation
Press the TIMER button can initiate the
Auto-start and Auto-stop setting program
of the unit.
2
1
2
To set the Auto-start/stop time.
2
1
1. Press the TIMER button, when the TIMER
ON indicator displayed on the LED window
of the air conditioner, it indicates the Auto
Start setting program is initiated. When the
TIMER OFF indicator displayed on the LED
window of the air conditioner, it indicates the
Auto Stop setting program is initiated.
2. Press or hold the Up( ) or Down( ) to
change the Auto time. The control will count
down the time remaining until start/stop.
3. The selected time will register in 5 seconds
and the air conditioner will automatically
revert back to display the previous temper ature setting.
4. Turning the unit ON or OFF at any time
will cancel the Auto Start/stop function.
COMBINED TIMER
(Setting both ON and OFF timers simultaneously)
AUTO STOP AUTO START
(On Stop Start operation)
This feature is useful when you want to stop the
2
air conditioner after you go to bed, and start it
again in the morning when you wake up or when
you return home.
Example:
To stop the air conditioner 2 hours after setting
and start it again 10 hours after setting.
1. Press the TIMER button until the TIMER
OFF indicator is displayed on the LED display
of the air conditioner.
2. Use the UP/DOWN button to display "2.0" on
the LED display of the air conditioner.
3. Press the TIMER button again to display the
TIMER ON on the LED display of the unit.
4. Use the UP/DOWN button to display "10" on
the LED display of the unit.
5. Wait for 5 seconds until the previous display
revert back to the LED window.
AUTO START ATUO STOP
(Off Start Stop operation)
NOTE: To cancel the TIMER setting, push
the TIMER button and press or hold the Up
( ) or Down( ) until 0 hour is displayed
on the LCD window of the air conditioner.
This feature is useful when you want to start
the air conditioner before you wake up and
stop it after you leave the house.
Example:
To start the air conditioner 5 hours after setting,
and stop it 8 hours after setting.
1. Press the TIMER button until the TIMER
ON indicator is displayed on the LED display
of the air conditioner.
2. Use the UP/DOWN button to display
"5.0" on the LED display of the air conditioner.
3. Press the TIMER button again to display
the TIMER OFF on the LED display of the unit.
4. Use the UP/DOWN button to display
"8.0" on the LED display of the unit.
5. Wait for 5 seconds until the previous display
revert back to the LED window.
77
88
Energy saver operation
In this mode, the fan will continue to
run for 3 minutes after the compressor
shuts off. The fan then cycles on for 2
minutes at 10 minute intervals until the
room temperature is above the set
temperature, at which time the compressor turns back on and cooling stars.
1
NOTE:
-Buttons design is based on typical model and might be slightly different
from the actual one you purchased, the actual shape shall prevail.
-All the functions described are accomplished by the unit, if the unit has
no this feature, there is no corresponding operation happened when
press the relative button on the remote controller.
-When there are wide differences between Remote controller Illustration
and USERS MANUAL on function description, the description on USERS
MANUAL shall prevail.
-The device could comply with the local national regulations. In Canada,
it should comply with CAN ICES-3(B)/NMB-3(B). In USA, this device
complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interfe rence, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
-This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for
compliance could void suers authority to operate the equipment.
99
1010
Loading...