Emerson EARC10RE1, EARC6RE1, EARC8RE1, EARC8RSE1, EARC12RE1 User Manual

MODEL:

EARC6RE1
EARC8RE1
EARC8RSE1
EARC10RE1
EARC12RE1

INTRODUCTION

IMPORTANT SAFETY INSTRUCTION ...........................................................................

ELECTRICAL REQUIREMENTS

PACKING LIST ............................................................................................................

INSTALLATION & ASSEMBLY INSTRUCTIONS .............................................................

USING YOUR AIR CONDITIONER ................................................................................

OPERATING YOUR AIR CONDITIONER

CARE AND CLEANING ................................................................................................

TROUBLESHOOTING .................................................................................................

...................................................................................

........................................................................

1

2

3

4

9

11

12

13

below:

1

(6K-8K) 0-8 amps
(10K-12K) 0-12 amps

(6K-8K) 10-amp

(10K-12K) 15-amp

2

3

FIG. 1

8

EXTERIOR
WALL

INTERIOR

WALL

STOOL
SILL

OFFSET

FIG. 2

0

EXTERIOR
WALL

INTERIOR

WALL

STOOL
SILL

OFFSET

4

(Only used for 6K/8K)

Head

6K-8K

10K-12K

5

Head

3

FIG. 3

FIG. 4

FIG. 5

6

(Suggest to keep a downward

, to let accumulated rain water to drain out,

angle

from back side of the unit bottom.)

FIG. 6

FIG. 7

FIG. 10

FIG. 11

FIG. 8

FIG. 12

FIG. 13

FIG. 9

7

FIG. 14

8

1

2

AUTO
SPEED

WIFI

WIFI Symbol*

NOTE: * means only available for WIFI modes, For more
information, please see the WIFI manual.

1. Shows the set temperature.

Digital Display:

Operation modes are: Cool, Dry, Fan, and Auto.
Time is displayed using the timer setting.

and Button:2. Use these buttons on the
control panel and remote to increase or decrease
the Set Temperature or Timer.
Temperature range: 61 ~88 or 16 ~31 .

3. Turn the air conditioner on and

Power Button:

off.

Press the mode button to cycle

4. Mode Button:
through the various modes: Cool, Dry, Fan and
Auto.

AUTO
MODE

3

Only available
for WIFI

456789

models.

Cool Mode: The cooling function allows the air
conditioner to cool the room and at the same time
reduces humidity. Press the MODE button to
activate the cooling function. To optimize this
function adjust the temperature by pressing the up
and down arrows and the speed by pressing the
Fan Speed button.
Dry Mode: This function reduces the humidity of
the air to make the room more comfortable. Press
MODE button to set the DRY mode. An automatic
function of alternating cooling cycles and air fan
is activated.

Fan Mode:

This mode will only circulate the air.
Press MODE button to select FAN MODE.
Pressing the FAN SPEED button allows you to
change the fan speed setting from HI, MED, and
LO. If using the remote control, it will store the fan
speed setting of the previous use.

Auto Mode: In AUTO mode the unit automatically
chooses the fan speed and the mode of operation
(COOL, DRY, or FAN). In this mode the fan speed
and the temperature are set automatically
according to the room temperature (

temperature

is determined by the temperature

sensor located in the indoor unit.

Room

).

Use buttons on the control panel

5. Timer Button:
and remote to set the TIMER.
Timer Off: The timed stop is programmed by
pressing the TIMER button. Set the time by
pressing the button or

stop

until your
desired stop time is displayed, then press TIMER
button again.

Timer On:

button first

the button or .

a second time, set the stop time

button or .

When the unit is off, press TIMER

, set the temperature with pressing

Press TIMER button

with pressing the

Press TIMER button a
third time, confirm your settings and stop time.
The display will show the time your machine will
automatically turn on.

Note: It can be set to automatically turn off or on in

0.5-24 hours. Each press of the
buttons will increase or decrease the timer. The
Timer can be set in 0.5 hours increment below 10
hours and 1 hour increment for 10 hours or above.
The SET light will turn on while setting.

To cancel the set function, press the TIMER button
again.

9

When the unit is in ECO mode, the

6. Eco Button:
light will turn on. In ECO mode, the unit will
turn-off once the room is cooled to the user set
temperature. The fan will also be off at this point.
The unit will turn back on when the room
temperature rises above the user set temperature.
Before the compressor stars, the fan motor will
run for a while, then it will stop for a while-and will
repeat to provide a much more comfortable-feeling
and save energy.

Press the SLEEP button, the Sleep

7. Sleep Button:
Light will be on after 10s. and the remaining lights
on the display will be off. In SLEEP mode, the air­conditioner will automatically adjust the
temperature and fan speed to make the room more
comfortable during the night. The set temperature

will automatically raise by 1 every 30-60

minutes and at most change six times until the set

10.

Use the horizontal wheels

Directional Louvers:

to control horizontal airflow and the air deflectors
to control vertical airflow.

horizontal wheelair deflector air deflector

temperature is 28 .

Run time will depend on set temperature.

Press the FAN SPEED button

8. Fan Speed Button:

to select the fan speed. In COOL MODE you can
choose the following settings: HI, MED, LO, or
AUTO. In FAN MODE you can choose from HI,
MED, and LO.

The Filter Check light will only turn

9. Fiter Button:

on as a reminder to clean the filter after the fan
motor has been in operation for a total of 500
hours. To turn the light off, press the Filter Check
button.

10

1

3

4

5

6

3

2

7

8
9

10

Use buttons on the control panel

5. Timer:

and remote to set the TIMER.
Timer Off: The timed stop is programmed by
pressing TIMER button. Set the time by
pressing the button or

desired stop time is displayed, then press TIMER
button again.

Timer On:

button first

the button or .

a second time, set the stop time

button or .

third time, confirm your settings and stop time.
The display will show the time your machine will
automatically turn on.

Note: It can be set to automatically turn off or on in

0.5-24 hours. Each press of the
buttons will increase or decrease the timer. The
Timer can be set in 0.5 hours increment below 10
hours and 1 hour increment for 10 hours or above.
The SET light will turn on while setting.

To cancel the set function, press the TIMER button
again.

When the unit is off, press TIMER

, set the temperature with pressing

Press TIMER button

Press TIMER button a

stop

until your

with pressing the

1. Turn the air conditioner on and off.Power:

2. Press the COOL button to COOL mode.Cool:

and :3. Use these buttons on the control
panel and remote to increase or decrease the
Set Temperature or Timer. Temperature range:
61 ~88 or 16 ~31 .

Press the SLEEP button, the Sleep

4. Sleep:

Light will be on after 10s. and the remaining
lights on the display will be off. In SLEEP mode,
the air-conditioner will automatically adjust the
temperature and fan speed to make the room
more comfortable during the night. The set

temperature will automatically raise by 1
every 30-60minutes and at most change six

times until the set temperature is 2
And every Run time will depend on set

temperature.

8 .

In AUTO mode the unit automatically

6. Auto Mode:

chooses the fan speed and the mode of operation
(COOL, DRY, or FAN). In this mode the fan speed
and the temperature are set automatically
according to the room temperature ().Room

temperature is determined by the temperature
sensor located in the indoor unit.

Press the FAN SPEED button

7. Fan Speed:

to select the fan speed. In COOL MODE you can
choose the following settings: HI, MED, LO, or
AUTO. In FAN MODE you can choose from HI,
MED, and LO.

To press the DISPLAY button, it can

8. Display:
switch off/on all lights or LED display.

When the unit is in ECO mode, the

9.

Eco:

light will turn on. In ECO mode, the unit will
turn-off once the room is cooled to the user set
temperature. The fan will also be off at this point.
The unit will turn back on when the room
temperature rises above the user set temperature.
Before the compressor stars, the fan motor will
run for a while, then it will stop for a while-and will
repeat to provide a much more comfortable-feeling
and save energy.

Press the Fan Only button to FAN

10.

Fan Only:

ONLY mode.

11

The
Check Filter light will automatically turn on after
the fan motor has been in operation for a total of
500 hours.

15

FIG. 15

12

13

For any questions or Technical Support,
Please Call Customer Service: 1-844-801-8880

14