Emerson CF2454WW02, CF2454BS02, CF2454PW02, CF2454BQ02 User Manual

READ AND SAVE THESE INSTRUCTIONS

Model No.

CF2454WW02 CF2454BS02
CF2454PW02 CF2454BQ02

THE ODYSSEY Series
Ceiling Fan Owner's Manual

Part No. F40BP72110008 Form No. BP7211-8

Net Weight: 26.0 Lbs.

®

WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.

Safety Instructions

1. Read your owner’s manual carefully and keep it for future reference

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service dis­connecting means cannot be locked, securely fasten a warning device, such as a tag, to the service
panel.

3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off
the power to the ceiling fan before servicing.

4. Do not put anything into the fan blades while they are turning.

5. Do not operate reversing switch until fan blades have come to a complete stop.

Additional Safety Instructions for Installation

1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not
operate fan without blades.

2. All wiring must satisfy National and Local Electrical Codes. Use the National Electrical Code if Local
Codes do not exist. The ceiling fan must be grounded as a precaution against possible electrical
shock. Electrical installation should be made or approved by a licensed electrician.

3. The outlet box and joist must be securely mounted an capable of reliably supporting a least 50
pounds. Use only U.L. outlet boxes listed as acceptable for fan support, and use the mounting
screws provided with the outlet box. Most outlet boxes commonly used for support of light fixtures
are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in
doubt.

4. The downrod furnished with the fan proves the minimum recommended floor to fan blade clearance
for an 8 foot ceiling.

5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental
contact with th fan blades.

6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not
know enough about electrical wiring, have your fan installed by a licensed electrician.

WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not
specifically approved for this fan.

WARNING: This product is designed to use only those parts supplied with this product and/or any
accessories designated specifically for use this product by Emerson Company could result in
personal injury or property damage.

WARNING: To Reduce the risk of personal injury, do not bend the blade flange when installing the
blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.

2

WARNING

!

1. Open styrofoam unit containing fan. Remove upper
and center sections of styrofoam unit. Remove parts
and check to see that you have received the following:

a. One fan motor and housing assembly
b. One motor coupling cover
c. One ceiling cover
d. Five fan blades
e. Five blade holder caps (left)
f. Five blade holder caps (right)
g. One hanger ball/downrod assembly
h. One hanger bracket
i. One light kit adapter assembly
j. One light kit plate assembly
k. One light kit glass
l. Two die cast light kit glass holders
m.One uplight lead assembly
n. One loose parts bag containing:

1. One setscrew

2. One 5/32" hex wrench

3. One 3/16” hex wrench

4. Four 8-32 x 1-1/4” threaded studs

5. Four knurled knobs

6. Four lockwashers

7. Seven wire connectors

8. Three 8-32 x 3/8" phillips head screws

9. One hairpin clip

10. One clevis pin

11. Twenty-one 10-32 x 3/8" pan head screws

12. One flatwasher

This Manual Is Designed to Make it as Easy as Possible for You to

Assemble, Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One six-inch blade screwdriver One stepladder
One Phillips head screwdriver One wire stripper
Seven wire connectors(supplied.)

MATERIALS

Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of the wire size,
to right:

3

Installed Wire Length Wire Size A.W.G.

Up to 50 ft. 14

50-100 ft. 12

Unpacking Instructions

For your convenience, check-off boxes are provided next to each step. As each step is completed, place a
check mark in the box. This will insure that all steps have been completed and will be helpful in finding
your place should you be interrupted.

If you feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.

NOTE: Place the parts from the loose parts bags
in small containers to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.

Do not install or use fan if any part is damaged or
missing. Call Toll-Free:

1-800-654-3545

This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or acces­sories not designated for use with this product by
Emerson Company could result in personal injury or
property damage.

WARNING

!

WARNING

!

WARNING

!

FAN BLADES

MOTOR
COUPLING
COVER

UPPER STYROFOAM
SECTION

BLADE HOLDER
CAPS (LEFT)

BLADE HOLDER

CAPS (RIGHT)
DIE CAST
GLASS HOLDERS

LIGHT KIT
GLASS

CEILING
COVER

LIGHT KIT
PLATE
ASSEMBLY

LOWER
STYROFOAM
SECTION

FAN MOTOR
AND HOUSING
ASSEMBLY

UPLIGHT
LEAD ASSEMBLY

HANGER BALL/
DOWNROD
ASSEMBLY

HANGER
BRACKET

LOOSE
PARTS
BAG

CENTER
STYROFOAM
SECTION

LIGHT KIT
ADAPTER
ASSEMBLY

Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.

The outlet box must be securely anchored and capa­ble of withstanding a load of at least 50 pounds.

If you feel that you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.

4

SECTION A

Assembly Instructions

for Installing the CF2454

Ceiling Fan with a

SW375 Receiver and

a SR330 Remote Control or

with a SW350 Wall Control

1. Cut the white, blue, and black wires about 3"
above the motor coupling (Figure 1). Strip insula­tion 1/2" from end of wires and install a wire con­nector on the black wire; this wire will not be used.
Remove the wire connectors from the red and
brown wires.

2. Loosen the setscrew in the hanger ball, slide the ball
down the downrod , and remove the clevis pin. Then
slide the hanger ball off the downrod (Figure 2).
Retain all parts for reinstallation in step 11.

3. Push the wiring harness connector (supplied with
the remote control) and the connector on the blue
wire (supplied with the SW375 Receiver) and the
uplight yellow lead assembly (supplied with the
fan) through the downrod until they extend about
4" out of the downrod. (Figure 3).

4. Cut all wires approximately 3" from the end of the
downrod’. Strip insulation 1/2" from end of wires.

Figure 1

Figure 2

Figure 3

IF THE CF2454 CEILING FAN IS BEING
INSTALLED WITH ANY OTHER CONTROL
METHOD, SKIP SECTION A AND GO TO
SECTION B TO BEGIN ASSEMBLY
INSTRUCTIONS.

Electrical Requirements

If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.

The Emerson CF2454 Ceiling Fan is designed to be
operated from a SR330 Remote Control, from a
SW350 Wall Control with a SW375 Receiver, or from
other fan/light controls. There are not controls supplied
with the ceiling fan. If you are going to control your
ceiling fan with a SR330 Remote Control or with a
SW350 Wall Control, proceed to “SECTION A”. If you
are to control your ceiling fan in any other manner,
proceed to “SECTION B”.

To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked acceptable for
fan support, and use screws supplied with outlet
box. Most outlet boxes commonly used for support
of light fixtures are not acceptable for fan support
and may need to be replaced. Consult a qualified
electrician if in doubt.

To avoid fire or shock, follow all wiring instructions
carefully.

Any electrical work not described in these
instructions should be done or approved by a
licensed electrician.

Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is
turned off at the main fuse box before wiring. All
wiring must be in accordance with National and
Local codes and the ceiling fan must be properly
grounded as a precaution against possible electrical
shock.

WARNING

!

WARNING

!

WARNING

!

INSULATE BLACK
WIRE USING WIRE
CONNECTOR

WHITE WIRE

YELLOW
WIRE

MOTOR
COUPLING

3"

BLACK WIRE

BLUE WIRE

REMOVE WIRE
CONNECTORS
FROM RED AND
BROWN WIRES

MOTOR COUPLING SLOT

CLEVIS PIN

HANGER BALL

DOWNROD

SETSCREW

WIRING
HARNESS

UPLIGHT YELLOW LEAD ASSEMBLY

4"

BLUE WIRE

DOWNROD

CUT HERE

3"

9. Screw two 1-1/4” threaded studs (supplied) into
the motor (Figure 6). Leave approximately 7/8” of
the stud extending above the motor. Slide the
motor cover over the downrod and rotate the cover
until the threaded studs protrude; install two
knurled knobs (supplied) to secure the cover.

NOTE: Make sure the unused black motor lead is
capped with a wire connector. Make sure all wire
connectors are completely inside motor coupling
cover and not pinched between the motor cou­pling cover and motor.

10. Position the ceiling cover over the downrod . Be

sure the cover is oriented correctly, with the large
opening at the top (Figure 7).

Figure 6

Figure 5

5

5. Using wiring connectors (supplied), connect the
white, red, blue, brown, and yellow wires from the
downrod to the white, red, blue, brown and yellow
wires of the ceiling fan (Figure 4). Wires must be
connected color-to-color.

6. Fold all wires from the downrod into the slot in the
motor coupling, slide the downrod down the wires
and seat the downrod in the motor coupling. All
wires and wire connectors should be placed
through the motor coupling slot beneath the down­rod (See Figure 5).

7. Align the clevis pin holes in the downrod with the
holes in the motor coupling. Install the clevis pin
and secure with the hairpin clip. The clevis pin
must go through the holes in the motor coupling
and the holes in the downrod (Figure 5). Push the
straight leg of the hairpin clip through the hole near
the end of the clevis pin until the curved portion of
the hairpin clip snaps around the clevis pin. The
hairpin clip must be properly installed to prevent
the clevis pin from working loose.

8. Install the setscrew (supplied in the loose parts
bag) in the motor coupling and tighten using the
5/32” setscrew wrench (supplied) (Figure 5).

Figure 4

It is critical that the clevis pin in the motor coupling
is properly installed and the setscrew securely tight­ened. Failure to verify that the pin and setscrew are
properly installed could result in the fan falling.

WARNING

!

SW375 RECEIVER

WHITE WIRE

YELLOW WIRE
TO YELLOW
WIRE

BLUE WIRE
TO
BLUE WIRE

BLACK WIRE
(NOT USED)

FAN BLADES REMOVED
FOR CLARITY

RECEIVER

CONNECTOR
WIRING HARNESS
CONNECTOR

WHITE WIRE

DOWNROD

RED WIRE
TO RED WIRE

BROWN WIRE
TO BROWN WIRE

BLUE WIRE
TO BLUE WIRE

WHITE WIRE
TO WHITE WIRE

YELLOW WIRE
TO YELLOW WIRE

LIGHT
FIXTURE

BLACK WIRE

BLACK WIRE

FAN
HOUSING

BLACK
WIRE

120V SUPPLY

120V SUPPLY

BLACK

BLACK

WHITE
WIRE

TO

WHITE

TO

LISTED GENERAL
USE ON/OFF
WALL SWITCH
(MUST BE
USED WITH
SR330 REMOTE
CONTROL)

SW350
WALL
CONTROL

YELLOW LEADS TO
BE POSITIONED IN
SLOT IN MOTOR
COUPLING

SETSCREW

CLEVIS PIN

HAIRPIN
CLIP

CLEVIS
PIN

DOWNROD

HAIRPIN
CLIP

MOTOR
COUPLING

DOWNROD

MOTOR COUPLING

CLEVIS
PIN

KNURLED KNOB

MOTOR
COUPLING
COVER

WIRE CONNECTOR

YELLOW LEADS

1-1/4" THREADED
STUD

7/8"

RED LEAD

BROWN LEAD

MOTOR
BRACKET

WIRE
CONNECTORS