Emerson CF110BS00, CF110ORB00 User Manual

Part No. F40BP74660000 Form No. BP7466
11/12 ETL Model No.: CF110

READ AND SAVE THESE INSTRUCTIONS

CALLAN

™

48” Ceiling Fan Owner's Manual

Model Numbers

CF110BS00 - Brushed Steel
CF110ORB00 - Oil Rubbed Bronze

Net Weight: 23.7 Lbs.

Questions, problems, missing parts: Before returning to the store call

Emerson Electric Customer Service

8 a.m. - 6 p.m., EST, Monday-Friday

1-800-654-3545

www.emersonfans.com

2

Safety Instructions

TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,
OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:

a. Use this unit only in a manner intended by the

manufacturer. If you have questions, contact the
manufacturer.

b. Before servicing or cleaning unit, switch power off

at service panel and lock service panel
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.

WARNING

!

Additional Safety Instructions for Installation

1. To avoid possible shock, be sure electricity is turned
off at the fuse box before wiring, and do not operate
fan without blades.

2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2011” and Local
Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.

1. Read your owner’s manual carefully and keep it for
future reference.

2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.

3. Do not put anything into the fan blades while they are
turning.

4. Do not operate reversing switch until fan blades have
come to a complete stop.

DATE CODE:

The date code of this fan may be found on the box, stamped in ink on a white label. You should record

this data above and keep it in a safe place for future use.

ETL Model No.: CF110

READ AND SAVE THESE INSTRUCTIONS

3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 15.9kg. (35 lbs.) or less”., and use the
mounting screws provided with the outlet box. Most
outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.

4. The downrod furnished with the fan proves the
minimum recommended floor to fan blade clearance
for an 8 foot ceiling.

5. The fan must be mounted with the fan blades at least 7
feet from the floor to prevent accidental contact with
the fan blades.

6. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.

WARNING: To reduce the risk of electrical shock, this
fan must be installed with an isolating wall
control/switch.

NOTE: This fan is suitable for use with solid-state speed
controls.

WARNING: To reduce the risk of fire or electrical shock,
this fan should only be used with fan speed control,
Model No. UC9020, manufactured by Rhine Electric Co.,
Ltd.

WARNING: This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use this product by Emerson
Electric Co. Substitution of parts or accessories not
designated for use with this product by Emerson could
result in personal injury or property damage.

WARNING: To reduce the risk of personal injury, do not
bend the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.

WARNING: To reduce the risk of electrical shock, this
fan must be installed with a general use, isolating
control/switch.

NOTE: All setscrews must be checked and re-tightened
where necessary before installation.

Unpacking Instructions

3

emersonfans.com

Please contact 1-800-654-3545 for further assistance

ETL Model No.: CF110

This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal injury
or property damage.

WARNING

!

Do not install or use fan if any part is damaged or
missing. Call Toll-Free:

1-800-654-3545

WARNING

!

1. Check to see that you have received the following

parts:

NOTE: If you are uncertain of part description, refer
to exploded view illustration.

NOTE: Place the parts from the loose parts bags in
a small container to keep them from being lost. If
any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.

2. Remove the fan assembly from the protective

plastic bag. Place the fan assembly into the upper
foam pad with the bottom of the motor facing up.

The upper foam pad serves as a holder for the fan
during the first stages of assembly.

PACKAGE CONTENTS

HARDWARE CONTENTS

Part Description Quantity

A Fan Motor Assembly 1

B Ceiling Canopy 1

C Coupler Cover 1

D Blade Flanges 5

E Fan Blades 5

F Hanger Bracket 1

G Hanger Ball/Downrod Assembly 1

H Upper Glass Retainer 1

I Glass Shade 1

J Lower Glass Retainer 1

K Finial 1

L SW46 Wall Control/Cover Plate 1

Part Description Quantity

1 Threaded Studs, #8-32 x 1-1/4” 2

2 Knurled Knobs, #8-32 2

3 Lockwashers, #8 2

4 Wire Connectors, Type E3 3

5 Clevis Pin 1

6 Hairpin Clip 1

7 Flange Screw (Spare), 1/4-20 x 1/2” 1

8 Washer, Paper #10 21

9 #10-32 x 5/16” Slotted Phillips Washer

Head Blade Screws 21

10 Blade Balance Kit 1

A

B

C

D

4

3

2

1

0

E

F

G

H

I

J

K

L

1

2

3

4

5

6

7

8

9

10

Before assembly your ceiling fan, refer to section on
proper method of wiring your fan (page 9). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.

WARNING

!

This Manual Is Designed to Make it as Easy as Possible for You to Assemble,

Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One Phillips head screwdriver One stepladder
One 1/4” blade screwdriver One wire stripper

Materials

Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:

Installed Wire Length

Wire Size A.W.G.

Up to 50 ft. 14

50-100 ft. 12

Ceiling Fan Assembly

4

ETL Model No.: CF110

Figure 1

Figure 2

Figure 3

1. Remove one of the motor housing screws and retain

for future use. Loosen the remaining three motor
housing screws for assembly of the lower glass
retainer (Figure 1).

2. Place the lower glass retainer onto the motor housing

and engage the key holes of the retainer onto the
three motor housing screws. Rotate the lower glass
retainer clockwise and tighten the three motor
housing screws. Reinstall the motor housing screw
(previously removed) into the remaining hole of the
lower glass retainer and tighen all screws securely
(Figure 2).

To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.

WARNING

!

3. Mount blade flange to fan blade using four

#10-32 x 5/16” slotted Phillips washers head screws
and four paper washers (Figure 3). Repeat this
procedure for the remaining four blades and flanges.

MOTOR HOUSING

MOTOR HOUSING
SCREWS

MOTOR HOUSING
SCREWS

LOWER GLASS
RETAINER

ROTATE LOWER
GLASS RETAINER
CLOCKWISE

#10-32 x 5/16" SLOTTED
PHILIPS WASHER HEAD
SCREWS (4 per blade assembly)

#10 PAPER WASHERS (4 per
blade assembly)

FAN BLADE

BLADE
FLANGE

5

emersonfans.com

Please contact 1-800-654-3545 for further assistance

ETL Model No.: CF110

Figure 4

Figure 5

Figure 7

Figure 6

NOTE: Take care not to scratch fan housing when
installing blades.

4. Attach the flange/blade assembly to the motor hub

using the two pre-installed 1/4-20 x 1/2” flange
screws and lockwashers. Make sure the screws are
tightened securely (Figure 4). Repeat this procedure
for the other four blade assemblies.

5. Screw the finial onto the center threaded stud of the

motor housing until securely tighten (Figure 5).

6. Carefully turn the partially assembled fan right side

up in preparation of final installation. Rest the fan
motor housing onto the packing styrofoam, being
careful not to bend the blades.

7. Carefully place the glass shade over the fan motor

housing, resting it into the lower glass retainer.
Orintate the glass shade so that the larger lip is
resting in the lower glass retainer per Figure 6.

8. Remove the four knurled retainer screws from the

motor housing and retain for future use.

9. Align the four holes of the upper glass retainer onto

the fan motor housing and reinstall the four knurled
retainer screws (previously removed). Securely
tighten all four screws (Figure 7).

1/4-20 x 1/2" FLANGE SCREWS WITH
LOCKWASHERS PRE-ASSEMBLED (2)

MOTOR HUB

FAN MOTOR HOUSING

GLASS SHADE

FLANGE/BLADE ASSEMBLY

FINIAL

UPPER GLASS
RETAINER

KNURLED RETAINER
SCREW (4)

LOWER GLASS
RETAINER

FAN MOTOR HOUSING