Emerson Avocent SV 220, Avocent SV 240, Avocent SV 340 Quick Installation Manual

Emerson® Avocent

®

SV 220/240/340

2 and 4-Port DVI-I KVM Switches

Quick Installation Guide

1

To Contact Avocent Technical Support: Visit www.avocent.com

590-1234-501A

Emerson, Emerson Network Power and the Emerson Network Power logo are trademarks or service marks of Emerson Electric Co. Avocent and the Avocent logo are trademarks or service marks of Avocent
Corporation. All other marks are the property of their respective owners. This document may contain confidential and/or proprietary information of Avocent Corporation, and its receipt or possession does not
convey any right to reproduce, disclose its contents, or to manufacture or sell anything that it may describe. Reproduction, disclosure, or use without specific authorization from Avocent Corporation is strictly
prohibited. ©2015 Avocent Corporation. All rights reserved.

HELPFUL RESOURCES

Product documentation downloads are
available at:

www.avocent.com/manuals

Search for additional product information at:

www.avocent.com

For further assistance, contact Avocent
Technical Support.

The following instructions will help
you install your Emerson® Avocent® SV
220/240/340 switch.

1

Connecting local peripherals

Turn off all computers you plan to use
with your SV 220/240/340 switching
system. Plug the monitor cable into the
appropriate CONSOLE port on the back of
the switch. Plug the USB keyboard cable,
USB mouse cable and two audio cables
(speaker/headset and microphone) into the
appropriate ports.

2

Connecting computers to the switch

Make sure all computers are turned off.
Plug the monitor, audio cables, keyboard
and mouse cables from the corresponding
computer into one of the ports on the
switch. Repeat for all computers.

3

Turning on your system

Turn the monitor on. Plug the power
supply cord into the switch. Plug the other
end of the power supply cord into an AC
wall outlet.The display diagnostic LED
should be solid green a few seconds after
power is applied. This indicates the display
EDID information has been captured and
secured.

4

Turning on the computers

Turn on all the attached computers
and check for display and peripheral
functionality.

5

Operating your switch

When the computers are turned on, the
computer connected to port 1 will be
displayed on the monitor. You can control
the Avocent® SV switch by using the front
panel push-buttons.

Emerson® Avocent® SV 340 dual-head switch shown

3

2

1

1

Emerson® Avocent

®

SV 220/240/340

2 and 4-Port DVI-I KVM Switches

Quick Installation Guide

2

To Contact Avocent Technical Support: Visit www.avocent.com

590-1234-501A

Emerson, Emerson Network Power and the Emerson Network Power logo are trademarks or service marks of Emerson Electric Co. Avocent and the Avocent logo are trademarks or service marks of Avocent
Corporation. All other marks are the property of their respective owners. This document may contain confidential and/or proprietary information of Avocent Corporation, and its receipt or possession does not
convey any right to reproduce, disclose its contents, or to manufacture or sell anything that it may describe. Reproduction, disclosure, or use without specific authorization from Avocent Corporation is strictly
prohibited. ©2015 Avocent Corporation. All rights reserved.

Supported Hardware

The SV switches support most DVI
monitors and video cards, VGA and HDMI
monitors and video cards (with adaptors),
microphones, speakers/headsets, USB
keyboards and USB mice.

Environmental

Operating temperature is 32° to 104° F (0°
to 40° C).

Storage temperature is -4° to 140° F (-20°
to 60° C).

Humidity requirements are 0-80% RH, non­condensing.

Mechanical

SV 220 Approximate Dimensions

H x W x D = 177 (W) x 61 (D) x 35.2 (H) mm
H x W x D = 7 (W) x 2.4 (D) 1.4 (H) inches

Weight: 0.5 kg / 1.1 lbs

SV 240 Approximate Dimensions

H x W x D = 342 (W) x 125 (D) x 42 (H) mm
H x W x D = 13.5 (W) x 5 (D) 1.7 (H) inches

Weight: 1.6 kg / 3.5 lbs

SV 340 Approximate Dimensions

H x W x D = 342 (W) x125 (D) x 56.6 (H) mm
H x W x D = 13.5 (W) x 5 (D) x 2.2 (H) inches

Weight: 1.85 kg / 4 lbs

Supported Resolution

Dual link DVI up to 2560 x 1600. Monitor
and video card support for the maximum
resolution will vary and should be verified
for compatibility.

Video Adaptors

The local port connectors and cable
connectors on the switch are DVI-I. Analog
monitors require an adaptor to connect
to the VGA port (VAD-27). Monitors with

digital-only connectors can be plugged
directly into the DVI-I connector on the
switch.

Target Video Connectors

All of the target video connectors and cable
connectors on the switch are DVI-I. Target
computers with analog connectors require
and adaptor to connect to the VGA port
(VAD-28). Target computers with digital
only connectors must use an adaptor to
match up with the DVI-D port (VAD-31).

Cables

Users can choose from 6 ft. or 10 ft. cables.

Contact an Emerson representative for
ordering details.