Emerson AMHURST CF880BS00, AMHURST CF880VNB00, AMHURST CF880VS00 Owner's Manual
Part No. F40BP74720000 Form No. BP7472
Revision: 130701 ETL Model No.: CF880
READ AND SAVE THESE INSTRUCTIONS
AMHURST
™
5544”” CCeeiilliinngg FFaann OOwwnneerr''ss MMaannuuaall
Model Numbers
CF880BS00 - Brushed Steel
CF880VNB00 - Venetian Bronze
CF880VS00 - Vintage Steel
Net Weight: 25.6 Lbs.
Questions, problems, missing parts: Before returning to the store call
Emerson Electric Customer Service
8 a.m. - 6 p.m., EST, Monday-Friday
1-800-654-3545
www.emersonfans.com
2
Safety Instructions
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,
OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b. Before servicing or cleaning unit, switch power off
at service panel and lock service panel
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.
WARNING
!
Additional Safety Instructions for Installation
1. To avoid possible shock, be sure electricity is turned
off at the fuse box before wiring, and do not operate
fan without blades.
2. All wiring must be in accordance with the National
Electrical Code “ANSI/NFPA 70-2011” and Local
Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.
3. The outlet box and joist must be securely mounted
and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use the
mounting screws provided with the outlet box. Most
outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.
4. The downrod furnished with the fan provides the
minimum recommended floor to fan blade clearance
for an 8 foot ceiling.
5. The fan must be mounted with the fan blades at least
7 feet from the floor to prevent accidental contact with
the fan blades.
6. Follow the recommended instructions for the proper
method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.
WARNING: To reduce the risk of electrical shock, this
fan must be installed with an isolating wall
control/switch.
NOTE: This fan is suitable for use with solid-state speed
controls.
WARNING: This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use this product by Emerson
Electric Co. Substitution of parts or accessories not
designated for use with this product by Emerson could
result in personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not
bend the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING: To reduce the risk of fire or electric shock,
this fan should only be used with fan speed control,
Model No. SW405, manufactured by Rhine Electric Co.,
LTD.
NOTE: All setscrews must be checked and re-tightened
where necessary before installation.
1. Read your owner’s manual carefully and keep it for
future reference.
2. Be careful of the fan and blades when cleaning,
painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.
3. Do not put anything into the fan blades while they are
turning.
4. Do not operate reversing switch until fan blades have
come to a complete stop.
DATE CODE:
The date code of this fan may be found on the box, stamped in ink on a white label. You should record
this data above and keep it in a safe place for future use.
ETL Model No.: CF880
READ AND SAVE THESE INSTRUCTIONS
Unpacking Instructions
3
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF880
This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Electric Co. Substitution of parts or
accessories not designated for use with this product
by Emerson Electric Co. could result in personal injury
or property damage.
WARNING
!
Do not install or use fan if any part is damaged or
missing. Call Toll-Free:
1-800-654-3545
WARNING
!
1. Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description, refer
to exploded view illustration.
NOTE: Place the parts from the loose parts bags in
a small container to keep them from being lost. If
any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.
2. Remove the fan assembly from the protective
plastic bag. Place the fan assembly into the upper
foam pad with the top of the motor facing up.
The upper foam pad serves as a holder for the fan
during the first stages of assembly.
PACKAGE CONTENTS
HARDWARE CONTENTS
Part Description Quantity
A Fan Motor Assembly 1
B Ceiling Canopy 1
C Coupler Cover 1
D Blade Flanges 5
E Fan Blades 5
F Hanger Bracket 1
G Hanger Ball/Downrod Assembly 1
H Light Kit Adapter 1
I Light Kit Assembly 1
J Glass Bowl 1
K 60-Watt (max.) Candelabra Bulbs 2
L Receiver/SW405 Wall Control 1
Part Description Quantity
1 Threaded Studs, #8-32 x 1-1/4” 2
2 Knurled Knobs, #8-32 2
3 Lockwashers, External Tooth #8 2
4 Wire Connectors, E3 3
5 Clevis Pin 1
6 Hairpin Clip 1
7 1/4-20 x 1/2” Pan Head Screws with
Lockwashers 11
8 #10-32 x 1/4” Washer Head Screws 16
9 #8-32 x 3/8” Pan Head Screw 1
10 Blade Balance Kit 1
A
B
C
D
E
F
....
G
OFF ON
H
I
J
K
L
1
4
7
8
2
9
3
65
10
1. Remove the hanger ball by loosening the setscrew in
the hanger ball until the ball falls freely down the
downrod (Figure 1). Remove the pin from the
downrod, then remove the hanger ball. Retain the pin
and hanger ball for reinstallation in Step 6.
2. Loosen the two setscrews in the motor coupler to
prepare for the installation of the downrod (Figure 2).
3. Separate, untwist and unkink the three 80” motor
leads. Route the motor lead wires through the
downrod. Align the clevis pin holes in the downrod
with the holes in the motor coupler. Install the clevis
pin and secure with the hairpin clip (Figure 2). The
clevis pin must go through the holes in the motor
coupler and the holes in the downrod. Be sure to
push the straight leg of the hairpin clip through the
hole near the end of the clevis pin until the curved
portion of the hairpin clip snaps around the clevis pin.
The hairpin clip must be properly installed to prevent
the clevis pin from working loose. Pull on the
downrod to make sure the clevis pin is properly
installed.
4. While pulling up on the downrod, tighten the two
setscrews in the motor coupler (Figure 2).
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 9). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.
WARNING
!
This Manual Is Designed to Make it as Easy as Possible for You to Assemble,
Install, Operate and Maintain Your Ceiling Fan
Tools Needed for Assembly
One Phillips head screwdriver
One stepladder
One wire stripper
Materials
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:
Installed Wire Length
Wire Size A.W.G.
Up to 50 ft. 14
50-100 ft. 12
Ceiling Fan Assembly
4
ETL Model No.: CF880
Figure 2
Figure 1
It is critical that the clevis pin in the motor coupler is
properly installed and the setscrews securely
tightened. Failure to verify that the pin and setscrews
are properly installed (as shown in Figure 2) could
result in the fan falling.
WARNING
!
PIN
DOWNROD
HAIRPIN CLIP
DOWNROD
MOTOR COUPLER
HANGER BALL
SETSCREW
SETSCREWS (2)
CLEVIS PIN
REINSTALL
SETSCREW (2)
MOTOR
COUPLER
HAIRPIN
CLIP
CLEVIS
PIN
5. Make sure the grommet is properly installed in the
coupler cover, then slide the coupler cover on the
downrod until it rests on the motor housing. Place the
ceiling cover over the downrod. Be sure that the
ceiling cover and the coupler cover are both oriented
correctly (Figure 3).
6. Reinstall the hanger ball (Figure 3) on the downrod
as follows. Route the three 80” motor leads through
the hanger ball. Position the pin through the two
holes in the downrod and align the hanger ball so the
pin is captured in the groove in the top of the hanger
ball. Pull the hanger ball up tight against the pin and
securely tighten the setscrew in the hanger ball.
A loose setscrew could create fan wobble.
7. The fan comes with blue, black and white leads that
are 80-inches long. Before installing the fan, measure
up approximately 6 to 9-inches above top of hanger
ball/downrod assembly. Cut off excess leads and
strip back insulation 1/2-inch from end of leads.
8. Carefully rotate the partial assembled ceiling fan
and place gently into the styrofoam to compete the
final installation of the fan.
9. Attach the blade flange to the fan blade using the
#10-32 x 1/4” washer head screw. Use three screws
with lockwashers per blade assembly (Figure 4).
10. Repeat this procedure for the remaining four blades
and flanges.
NOTE: Take care not to scratch fan housing when
installing blades.
11. Install one blade assembly on the top of the motor
housing using two 1/4-20 x 1/2” pan head screws
with lockwashers (supplied) (Figure 5).
12. Repeat this procedure for the remaining four blades
assemblies.
Ceiling Fan Assembly (continued)
5
emersonfans.com
Please contact 1-800-654-3545 for further assistance
ETL Model No.: CF880
Figure 4
Figure 5
To reduce the risk of personal injury, do not bend the
blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.
WARNING
!
Figure 3
It is critical that the pin in the hanger ball is properly
installed and the setscrew securely tightened. Failure
to verify that the pin and setscrew are properly
installed could result in the fan falling.
WARNING
!
HANGER
BALL
DOWNROD
PIN
CEILING
COVER
GROMMET
COUPLER
COVER
1/4-20 x 1/2" PAN HEAD
SCREW WITH
LOCKWASHER (2 per
blade/flange assembly)
#10-32 x 1/4"
WASHER HEAD
SCREW (3 per
blade/flange)
BLADE
FLANGE
BLADE/FLANGE
ASSEMBLY
MOTOR
HOUSING
6
ETL Model No.: CF880
Figure 6
Figure 7
Figure 8
13. Remove one of the screws from the motor housing.
Retain for future installation. Loosen the two
remaining screws in the motor housing for
installation of the light kit adapter.
14. Position the light kit adapter onto the motor housing.
Rotate the adapter clockwise to engage the keyhole
slots onto the two loosened screws of the motor
housing. Reinstall the screw previously removed
and tighten the three screws to complete the light kit
adapter installation (Figure 6).
15. Engage the white wire connector of the light kit
assembly with the white wire connector of the motor
connector (Figure 7). Engage the black wire
connector of the light kit assembly with the black
wire connector of the motor connector. Make sure
the connector latches are closed properly.
16. Remove one of the screws from the light kit
adapter. Retain for future installation. Loosen the
two remaining screws in the light kit adapter for
installation of the light kit assembly.
17. Carefully tuck all wires and connectors under the
light kit assembly while installing the light kit
assembly to the light kit adapter.
NOTE: Do not pinch wires between the light kit
assembly and the light kit adapter.
18. Place the light kit assembly onto the light kit
adapter. Rotate the light kit assembly clockwise on
the light kit adapter to engage the keyholes onto the
loosened screws. Retighten the two screws and
reinstall the screw previously removed. Tighten all
three screws securely (Figure 8).
19. You have now partially completed the assembly of
your new ceiling fan. You can now proceed with
hanging and wiring your fan.
Ceiling Fan Assembly (continued)
MOTOR HOUSING
SCREW (3)
LIGHT KIT
ASSEMBLY
BLACK WIRE
LIGHT KIT
ADAPTER
LIGHT KIT
ASSEMBLY
LIGHT KIT
ASSEMBLY
WHITE WIRE
KEY HOLE
SLOT (2)
MOTOR
CONNECTOR
WHITE WIRE
MOTOR
CONNECTOR
BLACK WIRE
LIGHT KIT ADAPTER
SCREW (3)
LIGHT KIT
ASSEMBLY
Loading...