INSTALLATION INSTRUCTIONS
AND USER GUIDE
AUTOMATIC OR MANUAL
STATIC STORAGE HEATERS
SH6M
SH9M / A
SH12M / A
SH15M / A
SH18M / A
SH24M / A
Please read these instructions before installing or
using this appliance for the rst time
IECEEIECEE
CB
SCHEME
Combined Storage Heaters !
2
INSTALLATION INSTRUCTIONS AND USER GUIDE
1.- WARNING
• Please read these instructions before installing or using this appliance for the first time. The warranty of the storage heater will
not cover any damage caused by non observance of any of these instructions.
• This Guide must be kept and given to any new owner.
• This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person
responsible for their safety.
• Should the heater be moved and reinstalled it is essential that the work is carried out by a fully qualified engineer.
• If during any installation the thermal insulation shows any sign of damage, it is necessary for the faulty part to be removed and
replaced by an identical part.
• The use of storage heaters is forbidden in any area where there is a presence of gases, explosives or inflammable objects.
• Do not use this heater to dry clothes. Do not cover this heater or put objects in contact.
• The air outlet grill at the top of the heater cabinet and the air inlet at the bottom of the heater are provided to ensure the most
efficient operation of the appliance. They also protect the heater from overheating; therefore, it is essential that at no time are
they covered.
• Surfaces of this appliance could be hot.
• Children should be supervised to ensure they do not play with the heater.
• This heater should be switched off at the isolating switch before any repair work is carried out. This action should also be taken
during the times of the year when heat is not required.
• The installation of the heaters must be carried out in such a way that each pole can be disconnected from the supply having a
contact separation of at least 3 mm.
• The storage heater should not be installed just below an electrical socket.
• The appliance must be installed in such a way that it is impossible for anyone using a bath or shower, to touch the controls.
• The nominal charging time of this storage heater is indicated on its rating plate and must be controlled by means of a
programmer.
• The installation must be carried out in accordance with the current electrical regulations.
• This appliance must be earthed.
• After installation a survey of the first charging cycle should be carried out to ensure that the main input thermostat switches off.
Ventilate the room during this first cycle.
• Before carrying out any work inside the appliance, the heater must be disconnected from the electricity supply.
• Never open a charged heater.
• The presence in the air of particles of smoke, dust and other pollutants could, in time, discolour the walls and surfaces around
the heater.
• To maintain stability, it is essential that the heater is placed on a level surface and care should be taken to avoid irregular
surfaces, such as may result from carpets or tiled surrounds partially protruding under the heater.
INTRODUCTION
Storage heaters are designed to take advantage of the considerable economical benefits of any restricted hour electricity tariff.
The heaters consume electricity only during the night, but due to the highly efficient storage medium, give you a truly economical
24 hours of comfort temperatures.
Type
SH6M
SH9M / A
SH12M / A
SH15M / A
SH18M / A
SH24M / A
Input
0.8 kW
1.2 kW
1.6 kW
2.0 kW
2.4 kW
3.2 kW
Voltage
220 – 240 V~
Charge
6.4 kWh
9.6 kWh
12.8 kWh
16.0 kWh
19.2 kWh
25.6 kWh
Weight
43 kg
61 kg
79 kg
98 kg
116 kg
152 kg
L
31.5 cm
43 cm
54 cm
65 cm
76.5 cm
99 cm
W
15 cm
H
72.5 cm
8.5 kg brick 4 - 8 4
12
16
13 kg brick - 4 - 4 - -
Combined Storage Heaters !
3
The input control operates a highly sensitive thermostat which regulates the amount of heat stored.
The discharge is by convection heat which can be partially controlled by use of the output control. Please note that Type SH6M
is fully automatic with no output control.
It is important that the correct rating of heater is installed to provide the selected level of heat. This will ensure the best possible
running costs against other fuels.
To reduce transport problems, the heater casings and storage bricks are packed separately.
You should be aware that Storage heaters, when fully charged, can have high surface temperatures.
2.- INSTALLATION INSTRUCTIONS
1.- Chose the right place to install the heater. It is necessary that a minimum clearance of 50 cm is allowed to ensure the best
heating results. Always maintain a minimum clearance of 50 cm from the heater to any combustible materials such as furniture
and curtains.
2.- Open the carton at the indicated side and fix the feet without removing the heater casing (fig 1). The screws are in the
accessories bag. Turn the carton upside down to allow the heater to stand on its feet and remove the carton. Check that it is the
correct model and that it is in good condition.
3.- Take off the front panel by removing the two screws at the bottom of the heater.
4.- Set the heater in the selected installation area and mark the fixing points on the wall using a pencil. Use the heater fixing
holes as a template and mark the wall through the fixing holes. Drill the required holes into the wall.
5.- Fix the heater to the wall. Please note the weight of the heater is taken by the feet, the wall fixing screws are only to prevent
the heater overturning. If there is any doubt as to the strength of the wall please consult an expert. Storage heaters are very
heavy and the installer must ensure that they are securely fixed and that there is no possibility of them overturning.
6.- Connect the heater using the enclosed wiring diagram. Ensure that all connections are firm. Use silicone covered wire. Do not
leave any remaining wire inside the heater.
7.- Remove the inner front panel with the attached convector element.
fig 1
fig 2
Combined Storage Heaters !
4
Warning!
At the other side of this front panel there is a breakable thermal insulation panel. Both sides must be handle with care. Avoid
touching the insulation and the convector element.
8.- Do not disconnect the electrical elements. Remove the packaging then lift and recline the elements.
9.- Place the storage bricks carefully, with the flat side facing the back of the heater. Arrange two rows of bricks (fig 3). Should
big bricks (ref 11072) are required they must be placed at the right side.
10.- Fix the elements in their original position. Place the other two rows of bricks with the knobs face to face.
11.- Refit the inner front panel. If the bricks have been fitted correctly you will find no difficulty in refitting the panel (fig 4).
12.- Attach the front panel and fix it at the bottom edge with the two screws provided.
fig 3
fig 4
Combined Storage Heaters !
5
3.- USING THE STORAGE HEATER
The two controls at the top of the heater govern the input and output functions. Both are printed with the numbers 1 to 5.
The charge (INPUT) control allows you to select the amount of heat you wish to store during the night.
During mild weather, it is normal to set your input control in a medium position. In cooler weather, the control could be set at 5 to
give maximum heat retention.
The stored heat will be delivered to the room by both radiant and convected methods. The convected heat can be regulated by
using the output control (OUTPUT) This control governs the continuous flow of convected heat from the outlet grill. Type SH6M
is completely automatic and has no output control.
All heaters have an exclusive feature which makes it unnecessary to close the output control at night. The outlet grill will close
automatically at the beginning of the overnight charge.
4.- MAINTENANCE OF YOUR STORAGE HEATER
This storage heater does not require any special care. During the first few charges you may be aware of an unusual odour. This
is normal and if it happens please ventilate the room until the odour disappears.
If dust accumulates on the heater surface it can be removed using a wet cloth when the heater is cold. Do not use solvents or
abrasive products for cleaning.
Night storage heaters are manufactured under an assured quality system using environment friendly procedures.
Please take the heaters to a clean point once their useful life is finished, in order to recycle their materials in the right way.
fig 5
Combined Storage Heaters
6
WIRING
R1, R2, R3, R4
Main heating elements
SH6M
SH9M / A
SH12M / A
SH15M / A
SH18M / A
SH24M/ / A
R1
800W
1200W
800W
1200W
800W
800W
R2 - -
800W
800W
800W
800W
R3 - - - -
800W
800W
R4 - - - - - 800W
R1 R3R2 R4
Ts
Tl
Tc
RAC
PE
N L
RAC Accelerating Resistance
Tc “Dual sensor” control thermostat
Tl Thermal limiter
Ts Safety
PE Earth
L Live
N Neutral
WARNING: In order to avoid overheating do not cover the heater.
The symbol on the product or in its packaging indicates that this product may not be treated
as household waste. Instead it shall be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste handling of this
product. For more detailed information about recycling of this product, please contact your
local city office, your household waste disposal service or the shop where you purchased the
product. These instructions are only valid in the EU member states.
Combined Storage Heaters
7
NOTES
As a part of the policy of continuous product improvement Elnur reserves the right to alter specifications without notice.
INSTALLATION INSTRUCTIONS AND USER GUIDE WEB VERSION
ELNUR UK Ltd.
Unit 1, Brown Street North
Leigh, Lancashire
WN7 1BU
www.elnur.co.uk
Customer Service Department:
Telephone +44(0)1942 670119
technical@elnur.co.uk
Manufactured by:
ELNUR, S.A.
Madrid, Spain
www.elnur-global.com
export@elnur-global.com
Management System International Certifications:
Loading...