ELNA Xperience 8200 Instruction Manual

1

IMPORTANT SAFETY INSTRUCTIONS

Your Elna 8200 embroidery sewing machine is designed and constructed for HOUSEHOLD use

only. Read all instructions before using this machine.

DANGER – To reduce the risk of electric shock:

1. Your sewing machine should never be left unattended when plugged in. Always unplug the machine
from the electrical outlet immediately after using and before cleaning.

2. Always unplug before replacing light bulb. Replace bulb with same type rated 12 Volts, 5 watts.

3. Do not reach for the machine if it has fallen into water. Unplug immediately.

4. Do not place or store machine where it can fall or be pulled into a tub or sink. Do not place it in or
drop it into water or other liquid.

WARNING – To reduce the risk of burns, fire, electrical shock or injury:

1. Do not allow machine to be used as a toy. Supervision is necessary when this machine is used by or
near children.

2. Use this sewing machine only for its intended use as described in this manual. Only use
attachments recommended by the manufacturer as described in this manual.

3. Never operate this machine if it has a damaged cord or plug, is not working properly, has been
dropped or damaged or dropped into water. Return the machine to the nearest authorized dealer or
service center for examination, repair, electrical or mechanical adjustment.

4. This machine is equipped with a special connection cord which, if damaged, must be replaced by an
identical cord. This can be obtained from your dealer.

5. Never operate the sewing machine with any air opening blocked. Keep ventilation openings of the
sewing machine and foot control free from the accumulation of lint, dust and fibers.

6. Never drop or insert any object into any opening.

7. Do not use outdoors.

8. Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.

9. To disconnect, turn machine off and remove plug from outlet.

10. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

11. Keep fingers away from all moving parts, especially the needle.

12. Always use the proper needle plate. The wrong plate can cause the needle to break.

13. Do not use bent needles.

14. Do not pull or push fabric while stitching. This may deflect the needle causing it to break.

15. Switch the sewing machine off when making any adjustment in the needle area, such as threading
needle, changing needle, threading bobbin, etc.

16. Always unplug the sewing machine from the electrical outlet when removing covers, lubricating or
making any other servicing adjustments mentioned in the instruction manual.

SAVE THESE INSTRUCTIONS

IMPORTANT

Be sure to keep machine away from static electricity, heat sources, humidity and direct sunlight.

USA only

Your machine comes equipped with a polarized plug (one prong wider than the other). A polarized plug
reduces the risk of electrical shock. This plug is intended to fit into a polarized outlet. If the plug does not
fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the
proper outlet. Do not modify the plug in any way.

2

TABLE OF CONTENTS

Machine Parts and Functions

Part Names ........................................................................................................................................................... 3

Standard Accessories ........................................................................................................................................... 4

Extension Table (Storage Box) ............................................................................................................................. 5

Free Arm ............................................................................................................................................................... 5

Presser Foot Lever and Additional Presser Foot Clearance ............................................................................... 5

Adjusting the Needle Thread Tension .................................................................................................................. 6

Getting Ready to Embroider

Connecting Machine to Power Supply ................................................................................................................ 7

Start/Stop Key....................................................................................................................................................... 8

LCD Touch Screen ................................................................................................................................................ 9

Design Selection Window Keys............................................................................................................................ 9

Mode Selection Window Keys ............................................................................................................................ 10

SET Preference Keys .................................................................................................................................... 11-13

How to Access On Screen Information .............................................................................................................. 14

Winding a Bobbin .......................................................................................................................................... 15-16

Inserting the Bobbin............................................................................................................................................ 17

Threading the Machine ....................................................................................................................................... 18

Built-in Needle Threader .................................................................................................................................... 19

Drawing Up the Bobbin Thread .......................................................................................................................... 20

Changing Needles .............................................................................................................................................. 21

Embroidery Hoops .............................................................................................................................................. 22

Stabilizers ........................................................................................................................................................... 22

Templates ........................................................................................................................................................... 23

Securing Fabric in Hoop ................................................................................................................................ 23-24

Attaching Hoop to Carriage ................................................................................................................................ 25

Embroidering Small Areas .................................................................................................................................. 26

Sewing Designs

How to Select a Built-In Design ..................................................................................................................... 26-27

Sewing a Single Built-in Design ......................................................................................................................... 28

Ready to Sew Window After Embroidery Begins ............................................................................................... 29

How to Select Alphabets ............................................................................................................................... 30-31

Sewing Alphabets .......................................................................................................................................... 32-33

Alphabet Corrections .......................................................................................................................................... 34

2 Letter or 3 Letter Monograms .......................................................................................................................... 35

Sewing with PC Design Cards ........................................................................................................................... 36

Edit Window ........................................................................................................................................................ 37

Selecting a Design After Opening the Edit Window...................................................................................... 38-39

Combine a Built-in Design with Alphabet ...................................................................................................... 40-41

Saving a Design in a File ............................................................................................................................... 42-43

Opening a Saved File ......................................................................................................................................... 44

Embridery with Optional Free Arm Hoop C ........................................................................................................ 45

Taking Care of Your Machine

Cleaning the Hook Area ..................................................................................................................................... 46

Replacing the Bobbin Case ................................................................................................................................ 47

Changing the Light Bulb ..................................................................................................................................... 47

DESIGN CHART.......................................................................................................................... 48-49

TROUBLESHOOTING ...................................................................................................................... 50

INDEX .......................................................................................................................................... 51-52

NOTE: Information found in this instruction manual is current at the time of printing. Elna
reserves the right to change and update specifications and information as needed.

3

Machine Parts and Functions

Part Names

1. Top cover

2. Design chart

3. Spool pin

4. Spool holder, large

5. Bobbin winder cutter

6. Bobbin winder spindle

7. Bobbin winder stop

8. LCD touch screen

9. Start/Stop key

10. Bobbin cover plate release button

11. Extension table (accessory storage box)

12. Bobbin cover plate

13. Needle plate

14. Built-in needle threader

15. Thread cutter and holder

16. Face plate

17. Thread tension dial

18. Thread take-up lever

19. Thread guide slit

20. Needle clamp screw

21. Needle

22. Presser foot

23. Carrying handle

24. Presser foot lever

25. Carriage

26. Machine socket

27. Power switch

28. Card eject button

29. PC design card (optional)

30. PC design card slot

31. Flywheel (always turn towards you)

1

2

3

4

6

5

7

8

12

11

10

9

15

14

13

17

16

18

22

21

20

19

27

26

25

24

30

29

28

31

23

4

Standard Accessories

1. Bobbins

2. Lint brush

3. Additional spool pin

4. Spool pin felt

5. Spool stand

6. Spool holder (large)

7. Spool holder (small)

8. Scissors

9. Screw key

10. Screwdriver

11. Set of needles

12. Standard hoop – A (with template)

13. Large hoop – B (with template)

14. Power supply cord

15. Instruction Manual

16. Template sheets

11

6

5

43

2

1

10

9

87

13

12

15

14

16

5

Extension Table (Storage Box)

Most accessories are stored inside the extension
table.

To Open:

Pull cover towards you. Lift out the packet of
accessories.

Ferr Arm

Remove the extension table to access the free
arm.

To Remove:

Lift out extension table away from the machine, as
shown.

NOTE: Always embroider with the extension table
attached unless using optional free arm hoop C.
See page 45.

To Attach:

Place tabs over slots and push down on table.

Presser Foot Lever and Additional Presser
Foot Clearance

Raise and lower the foot with this lever q.

Before sewing can occur, the presser foot must be
lowered to close the tension discs.

You can raise the presser foot about 6.5 mm (1/4")
higher than the normal up position for easier

removal of the hoop. Pull the presser foot lever q
up beyond the normal up position.

q

6

3

2

1

2

1

3

Adjusting the Needle Thread Tension

Align the number 2 on the tension dial with the
setting mark q.

Balanced thread tension:

A small portion of needle thread should appear on
the underside of the fabric.

When adjusting needle thread tension, the higher
numbers tighten, the lower numbers loosen.

•Tension is too tight

The bobbin thread shows through on the topside
of the fabric.

Turn the dial to a lower number to loosen the
needle thread tension.

•Tension is too loose

The needle thread forms loops and looks ragged.

Turn the dial to a higher number to tighten the
needle thread tension.

q

q

7

N

O

Getting Ready to Embroider

Connecting Machine to Power Supply

Machine has an auto voltage system and will
automatically adjust to any local power supply
voltage between 100 and 240V, 50/60 Hz.

Always use the power supply cord that came with
the machine.

To connect machine to power supply, turn off the
power switch

q. Insert machine plug w into the

machine and the power supply plug e into the
wall socket.

Your machine may come equipped with a
polarized plug (one prong wider than the other). A
polarized plug reduces the risk of electrical shock.
This plug is intended to fit into a polarized outlet. If
the plug does not fit fully into the outlet, reverse
the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet. Do not
modify the plug in any way.

For Your Safety

Do not use extension cords or plug adapters.

Do not touch plug with wet hands.

Always turn off the power/light switch first and then
unplug from the electrical outlet. Examples:

• when leaving the machine unattended

• when cleaning the machine

• when attaching or removing parts such as
needle or needle plate

Do not place heavy items on cords. Do not subject
cords to heat. Do not use damaged cords. Have
the cord repaired immediately.

While the machine is in operation, always keep
your eye on the sewing area and do not touch
any moving parts such as the thread take-up
lever, flywheel or needle.

q

w

e

8

Edit

Mode

1 2 3 4

5 6 7 8

Designs

Hoop Size A(F): 126X110mm

A Z

IMPORTANT:
Before turning on your machine, clear
your table surface of anything that might
obstruct the carriage movement. If your
machine is in a cabinet, check that the
machine is even or above the cabinet
surface. (The carriage could possibly hit
the cabinet and disturb the sewing result.)

TURN ON THE POWER SWITCH.

NOTE: After turning on the machine there is

approximately a six second delay before the LCD
To uch Screen becomes visible. (This is the
required boot up time and is not a malfunction.)

q Start/Stop Key (changes color to indicate

function)

Press this (green) key to start the machine.
When the machine is running, press this (red)
key to stop machine.

NOTE: The Elna 8200 is equipped with a
safety feature that will automatically shut down
the machine to prevent overheating if it is
running overloaded. Follow the instructions
that appear in the LCD touch screen should
this occur.

q

9

Edit

Mode

1 2 3 4

5 6 7 8

Designs

Hoop Size A(F): 126X110mm

A Z

LCD Touch Screen

When the machine is turned on, the design
selection window will appear in the LCD touch
screen.

NOTE: Only a light touch is required when
making a selection on the LCD touch screen. Do
not touch the surface of the screen with any hard
or sharp object, such as pencils, pens,
screwdrivers, etc.

Design Selection Window Keys

1. Built-in designs

There are 58 built-in designs. For an overview,
see page 48.

2. Alphabets

Three distinctive fonts – Gothic, Script and
Cheltenham. In addition, 2 letter and 3 letter
monogramming. See page 30.

3. PC design cards (optional)

Please verify that this machine will accept
compact flash card. See page 36.

4. Edit

This is the window where you can modify and
combine designs. See page 37.

5. Next key

Touch this key to go forward to next window in
sequence.

6. Previous key

Touch this key to go back to the previous
window in sequence.

7. Window category

Names the window function based on the
activated category.

8. Hoop recommendation

Identifies the appropriate hoop (and shows its
dimensions) depending on the designs
displayed on the screen. The example shows
standard rectangular A hoop and the optional
round F hoop.

9. Sound

This symbol indicates the beep sound is on.
See page 11.

10. Mode key

This key opens the mode selection window.

See page 10.

3

2

7

91

54

6

10

8

10

Edit

Mode

1 2 3 4

5 6 7 8

Designs

Hoop Size A(F): 126X110mm

A Z

Mode Selection Window Keys

The mode key is displayed in the selection
window no matter the category: built-in designs,
alphabets, PC design cards or edit.

Touch the “Mode” key.

The mode selection window will open.

1. Open file key

Any designs that have been saved can be
recalled. See page 44.

2. SET preference key

You can program the machine to change the
default settings to reflect your personal sewing
style. See page 11.

3. On screen information key

View basic operation information windows.
See page 14.

4. Return carriage key

Use this key to bring the carriage back to the
store position after completing embroidery.

IMPORTANT: Always have the carriage in the
stored position before turning OFF the
machine.

5. Return key

Use this key to close this window and return to
the previous window.

3

5

4

21

11

Edit

Mode

1 2 3 4

5 6 7 8

Designs

Hoop Size A(F): 126X110mm

A Z

Screen Contrast

+

inch/mm

5

+

Eco Mode

SET

inch

mm

Register

10

min

SET Preference Keys

These functions can be set according to your
preferences: screen contrast, sound volume, eco
mode, inch/mm, adjust key position, set maximum
embroidery speed, sewing light, thread selection,
format and language.

Touch the “Mode” key.

Touch the “SET” preference key to access and
personalize the machine settings.

1. Screen contrast
The LCD touch screen has an adjustable
backlight so the contrast can be lightened or
darkened. Touch the “+” key to darken and the
“–” key to lighten.

2. Sound
The beep volume default setting is 5 but it can
be adjusted between 0 (off) and 10 (loud).
Touch the “+” key to increase and the “–” key
to decrease or turn off.

3. Eco Mode
After turning on the machine this energy
saving feature will darken the LCD touch
screen and turn off the sewing light if the
machine has not been used. Simply touch the
LCD screen for the screen and light to turn
back on. The eco mode default setting is 10
minutes but it can be adjusted between 1 and
30 minutes. Touch the “+” key to increase and
the “–” key to decrease. If you want to turn off
the eco mode, touch the “+” key until “OFF”
appears in the display.

4. Inch/millimeter
Choose to have the measuring unit for designs
readout in either inch or millimeters. The
default unit setting is millimeters. Touch either
the “inch” or “mm” key.

5. Touch the “Next” key.

NOTE: Any change in the set preference window
must be “registered” to be activated. Only touch
the “Register” key (6) after making all changes
desired.

1

2

3

4

5

6

12

Key Position Adjustment

END

Key Position Adjustment

Sewing Light

+

Maximum Speed Setting

SET

Register

650spm

Yes

Key Position Adjustment

Sewing Light

+

SET

Register

650

spm

Yes

Maximum Speed Setting

Key Position Adjustment

PRESS MARK ( )

+

.

7. Adjust key positions
If the touch keys in the LCD touch screen do
not react to your touch, the keys may need to
be adjusted or realigned.

Touch the “Yes” key to open the key position
adjustment window.

The first of five black plus (+) symbols will
appear. Touch the black symbols in the order
that they appear.

After the fifth black symbol is touched, the
END message appears. Wait a few moments
and the set preference window reappears.

8. Set maximum embroidery speed
The maximum embroidery speed default
setting is 650 spm (stitches per minute).
Designs featuring narrow zigzag stitches may
need to be sewn at a slower speed for best
results. Touch the “–” key to decrease and “+”
key to increase.

9. Sewing light
You can operate the machine with the sewing
light on or off. Touch this key to change
between the two settings.

Touch the “Next” key.

7

8

9

13

Thread selection

Reset all to defaults

Format

Built-in Memory
ATA PC Card

SET

Register

Madeira

Mettler

Robison­Anton

Yes
Yes

Yes

10. Select thread brand
Choose from three popular brands of
embroidery thread. The default thread brand is
Robinson-Anton®. Touch the key that
represents the brand of thread you use most
commonly. The color code and name for that
brand of thread will be displayed in the LCD
screen after selecting a design.

Format

If the built-in memory or PC design card does not
function because the memory bank is damaged,
you must re-enable by formatting the memory.

NOTE: Formatting will erase all stored data.

11. Built-in memory
Touch “Yes” key next to Built-in memory.

12. PC design card (or Compact Flash)
Touch “Yes” key next to ATA PC card.

13. Reset to factory defaults
Touch this key to return everything, except
language, to the default settings (same
settings as when you purchased the machine).

14. Language selection
Touch the language key to open the language
selection window.

Choose from eleven languages. Touch the key
that represents the language you desire.

a. English
b. French
c. Spanish
d. Italian
e. Dutch
f. German
g. Portuguese
h. Swedish
i. Russian
j. Finnish
k. Japanese

15. Register key
Touch this key to save your personal settings
and exit the set preferences window. If you
touch the “Return” key (16), you will exit the
set preference window but the new setting will
not be saved.

10

11

12

13

14

c

b

a

15

d

e

f

g

h

i

j

k

(16)

14

Edit

Mode

1 2 3 4

5 6 7 8

Designs

Hoop Size A(F): 126X110mm

A Z

Index

Changing needles
Inserting the bobbin

Winding the bobbin

Threading the machine

?

?

?

?

Changing needles

How to Access On Screen Information

The LCD touch screen can show you information
for these basic machine operations: changing
needles, inserting the bobbin, threading the
machine and winding the bobbin.

1. Touch the “Mode” key to open the mode
selection window.

2. Touch the “On Screen Information” key to
open the index window.

3. Touch one of the keys in the index window.

4. View the illustrations of the topic selected.

5. Touch the “Return” key to go back to the
index window. Touch “Return” key again to
exit mode selection window.

2

5

3

1

15

Winding a Bobbin

To remove bobbin, slide bobbin cover plate
release button q to the right and lift away the
bobbin cover plate w.

Lift out the bobbin e. (Always use bobbin type
supplied with machine.)

Lift up the spool pin. Place the spool of thread on
the spool pin with the thread coming off the spool
as shown. Attach the spool holder and press it
firmly against the spool of thread.

NOTE: Spool holder needs to be changed
according to the type of thread spool

(A) Large spool
(B) Small spool

Additional Spool Pin

The additional spool pin can be used to wind a
bobbin without unthreading the machine.

PROCEDURE: Insert the spool stand w and the
additional spool pin e in the hole q. Place the felt r
and spool t on the pin with the thread coming off

the spool as shown.

NOTE: Hole is located in front and to the right of
the standard spool pin.

q

w

e

(A)

(B)

w

e

q

r

t

16

21

3

Using both hand, pull thread towards left and
insert thread into slit.

Pull the thread (dotted line in illustration) around
the thread guides following the broken lines
indicated on the machine .

Pass the thread through the hole in the bobbin
from inside to the outside. Place the bobbin on the

bobbin winder spindle

w.

Push bobbin winder spindle to the right. (The LCD
touch screen will show a bobbin winding
message.) Holding the free end of the thread,
press the Start/Stop key. Stop machine after the
bobbin has made a few turns. Cut the thread tail
close to the hole in the bobbin. Start machine
again to continue winding bobbin. When the
bobbin is fully wound, stop the machine.

Move the spindle to the left to return the bobbin
winder to its original position. Remove the bobbin

and cut the thread with the bobbin winder cutter e.

NOTE: Do not move the bobbin winder spindle
while the machine is running.

If the machine is running for more than two
minutes during bobbin winding, it will automatically
stop for safety purposes.

q

w

e

q

q

w

17

Inserting the Bobbin

Place the bobbin in the bobbin case with the
thread running counterclockwise.

Guide the thread into notch q on the front side of
the bobbin case. Hold the bobbin with your right
hand and pull the thread to the left, through the
tension spring blades.

Continue pulling the thread lightly until the thread
slips into notch w.

Pull out about 15 cm (6") of thread.

Replace the bobbin cover plate.

Refer to the chart shown on the bobbin cover plate
to check the threading.

q

w

18

Threading the Machine

Raise the presser foot with the presser foot lever.
Hand turn the flywheel (always turn towards you)
to bring the needle up to its highest position.

Using both hands, pull thread towards left and
insert thread into slit. firmly insert the thread under

the thread guide plate .

Pull thread foward around guide . (Thread
pathway is indicated on the machine with solid
line.)

Guide the thread down right channel and around
the thread holder .

Pull the thread up the left channel to the take-up
lever. Firmly pull the thread from right to left, over
the take-up lever and down into the take-up lever

eye r.

Proceed down left channel and through the lower
thread guide t.

Slide the thread to the left behind the needle bar
thread guide y.

Thread the needle from front to back manually or
use the built-in needle threader. See page 19.

4

21

3

q

w

e

e

t

y

r

q

w

19

Built-in Needle Threader

Hand turn the flywheel (always turn towards you)
to bring the needle up to its highest position. Turn
OFF the power switch. Lower the presser foot.

Pull down the needle threader lever q as far as it
will go. Hook

w is automatically inserted into the

needle eye.

Bring the thread around guide e and under hook

w.

Slowly release the lever while holding the thread
end and let the needle threader return to its

original position. A loop of thread r is pulled
through the needle eye.

Pull the thread loop off the guide to the back and
manually bring the thread through the needle eye.

NOTE: The needle threader can be used with #11
to #16 size needles. Thread weight may vary from
30 to 90.

If the needle threader does not catch a thread
loop, check the needle and positioning.

q

w

e

w

r

20

Drawing Up the Bobbin Thread

Raise the presser foot and hold the needle thread
lightly with your left hand.

Hand turn the flywheel (always turn towards you)
one full revolution. Draw up the needle thread
together with a loop of bobbin thread.

Pass the needle thread through the embroidery
foot. Pull thread up and secure it into thread holder

(located on front side of thread cutter)

q and leave

a small thread tail.

q

21

Changing Needles

Never use a bent or blunt needle, as it may cause
skipped stitches or thread breakage. Defective
needles can ruin the fabric. Always purchase good
quality needles. Change needles often.

Turn OFF the power switch. Hand turn the flywheel
to bring needle up to highest position. Lower the

presser foot. Turn the needle clamp screw q
counterclockwise to loosen. Remove the needle
from the clamp.

Insert the new needle into needle clamp with the
flat side w to the back, pushing it up as far as it
will go. Tighten the clamp screw firmly.

To determine if the needle is defective, place the
flat side of the needle on something flat (a needle
plate, piece of glass, etc.). The gap between the
needle and the flat surface should be consistent.

NOTE: Use a 75/11 needle for fine fabrics and a
90/14 needle for medium to heavyweight fabrics.
Your Elna 8200 comes inserted with a 75/11
needle.

q

w

22

Embroidery Hoops

Hoop A

The embroidery area is 126mm x 110mm
(5" x 4 3/8"). Ideal for sewing many of the built-in
designs and designs from optional PC design
cards.

Hoop B

The embroidery area is 140mm x 200mm
(5 1/2" x 8"). Use the generous dimensions of this
hoop for large size designs or combine several
designs or alphabets into one arrangement.

Hoop Part Names:
q Outer hoop

w Inner hoop
e Hoop turnkey
r Hoop tightening screw

Stabilizers

All embroidery needs some form of stabilizer that
can be easily removed. Use a stabilizer
appropriate to the fabric and project. Common
forms of stabilizer for embroidery sewing are
fusible, adhesive, tear-away, heat-away or wash­away.

The fusible type is recommended for stretch
fabrics and fabrics that might shrink. Adhesive type
is great for velvets or other napped fabrics that
would be damaged if secured in the hoop. The non
adhesive types should be used when embroidering
fabric which cannot be ironed or for areas which
are difficult to iron.

Most stabilizers should be used on the wrong side
of fabric. More than one layer may be required.
Wash-away stabilizer may be placed on top of
fabrics like toweling so the loops lay flat under the
embroidery.

For any type of stabilizer, prepare a piece larger
than the embroidery hoop and place it in the hoop
so that the entire piece can be fastened within.

q

w

e

r

e

q

w

r

A

B

23

Templates

Each hoop comes with a template to help you
place your design where you want it on the fabric.

There are a variety of starting points visible on the
template. Find the one that is appropriate for your
machine/design.

q Starting point for built-in and PC

design cards.

w Starting point for alphabets with horizontal

placement.

e Starting point for 100 series EnVision card

and for Elna EnVision CE20 and 8007.

r Boundary edges for built-in and PC design

cards.
Starting point for alphabets with vertical
placement.

NOTE: The four indentations

t for fitting the

template onto the hoop do not correspond with any
of the reference lines.

Securing Fabric in Hoop

Use a washable fabric marker or tailor’s chalk to
draw centerlines q on your fabric (see stabilizers
on page 22).

Loosen the hoop tightening screw w and lift out
the inner hoop.

STARTING POINT

STARTING POINT FOR MONOGRAMMING

STARTING POINT FOR MEMORY CARDS ( FROM No.1001 )

STARTING POINT FOR MEMORY CARDS ( FROM No.102 )

q

w

q

w

e

r

t

y

y

t

24

L

R

Fit the template e into the inner hoop. (L and R
markings on the inner hoop should be visible.)
Place the inner hoop and template over the fabric,
matching the centerlines.

Place the outer hoop on a flat surface. Position
inner hoop, template and fabric over the outer
hoop.

Set inner hoop into outer hoop and slightly tighten
the hoop tightening screw r. Gently pull fabric taut
in hoop, respecting the fabric grain (vertical and

horizontal). Check fabric and template centerlines.
Once fabric is taut and properly positioned, tighten
adjustment screw with screwdriver.

Remove template from inner hoop.

e

r

25

START

STOP

Attaching Hoop to Carriage

Lift up the presser foot. Rotate the hoop turnkey q
so it lies parallel to the hoop. With the hoop
turnkey turned towards the back, slide the hoop
from left side of machine. Position the hoop pins w

into the holes e on the carriage.

Rotate the hoop turnkey clockwise to lock hoop
onto carriage.

CAUTION:

Always allow plenty of room behind the carriage so
it can move freely. See page 8.

Never try to move the carriage by hand or touch
the carriage when it is moving.

Always return the carriage to store position before
turning off the machine. See page 10.

q

w

e

26

Edit

Mode

1 2 3 4

5 6 7 8

Designs

Hoop Size A(F): 126X110mm

A Z

Edit

Mode

1

2

3 4

Ready to Sew

A Z

Size

P

A(F): 126 x110m m

Jog

ST

2

1

30 min

5 colors

109x84mm

5597

5776

5802

5757

Snow
White

Seashell

GS
Gray

Green
Dust

Embroidering Small Areas

Attach stabilizer (cut larger than embroidery hoop)
to small piece of fabric. Draw centerline and place
stabilizer in hoop.

Sewing Designs

How to Select a Built-In Design

The built-in designs have been organized by
recommended hoop size (A or B) and subject
matter (animals, floral, ocean life, etc.).

To select a design, touch the key that represents
the design you desire.

Hoop size warning message appears. Touch
“Return” key.

The ready to sew window opens. The LCD touch
screen now shows the design information like the
image, thread colors, sewing time, etc.

q Color/Part key

The design is separated into parts based on
thread color changes. The parts are sewn in
the order displayed. Thread color names and
numbers are shown based on your thread
brand preference (see page 13). The part that
will be sewn is darkened.

After a part is sewn, the machine will
automatically stop and the next color part key
will darken. Change thread to next color and
continue sewing.

How to Sew a Specific Part (Skipping)

You can eliminate parts of the design by
touching the “Color/Part” key previous to the
part you wish to sew. All parts located before
that color/part key will lighten.

w Next key

This key will be displayed if there are more
parts to the design. Touch the key to view the
other parts.

q

w

27

Trace outline

Cancel

Edit

Mode

1

2

3 4

Ready to Sew

A Z

Size

P

A(F): 126 x110m m

Jog

ST

2

1

30 min

5 colors

109x84mm

5597

5776

5802

5757

Snow
White

Seashell

GS
Gray

Green
Dust

q Return key

Touch this key to close this window and return to the
design selection window.

w Jog keys

The needle must be aligned directly above the
centerlines on the fabric. Touch these keys to adjust
the hoop position.

NOTE: See page 29 for explanation of “Jog/St” key.

e Trace key

Check the size and sewing area of the design. Touch
this key. A message appears and tracing function
automatically starts. The carriage traces the outlying
boundaries of the design without any stitching.

r Cancel key (within tracing message)

You can cancel the tracing function while it is
happening by touching this key.

t Mode key

See page 10.

Sewing Information

a. Recommended needle thread tension
b. Sewing time in minutes
c. Number of colors/parts
d. Design size
e. Embroidery foot P
f. Appropriate hoop and its dimensions

q

w

e

r

t

a

b

c

d

e

f

28

Edit

Mode

1 2 3 4

5 6 7 8

Designs

Hoop Size A(F): 126X110mm

A Z

START

STOP

Edit

Mode

1

2

3 4

Ready to Sew

A Z

Size

P

A(F): 126x 110mm

Jog

ST

2

1

30 min

5 colors

109x84mm

5597

5776

5802

5757

Snow
White

Seashell

GS
Gray

Green
Dust

Sewing a Single Built-in Design

Select a design.

Touch “Return” key in the hoop size warning
message.

Hoop fabric and attach hoop to carriage. Position
needle directly over centerlines on fabric. Thread
machine with first thread color. Lower presser foot.

Press “Start/Stop” key and sew 5 or 6 stitches.
Stop machine by pressing “Start/Stop” key.

Raise presser foot. Cut away beginning thread tail
close to the start point. Lower presser foot.

Press the “Start/Stop” key and let the machine sew
until it stops automatically for the thread change.

Sew entire design using method described above
for each thread change.

When design is finished, the word “Completed” will
appear. Touch the “Return” key.

The design should be aligned with the centerlines
on the fabric.

HINT: You can check the design positioning before
sewing with the tracing key or template sheets.

29

Ready to Sew Window After Embroidery
Begins

When you start to sew, the ready to sew window
will change – jog keys disappear and current stitch

count q, stitch minus/plus keys and return carriage
key appear.

Thread Breaks

If the needle thread breaks, the machine will stop
and show a warning message. Touch the “Return”
key. Rethread machine.

w Stitch Minus/Plus keys

Touch the “–” key to move the hoop back to
the point before the thread break occurred.
Each time you touch the “–” key the hoop
moves back 10 stitches. Each time you touch
the “+” key the hoop moves forward 10
stitches.

e Jog/ST key

Touch this key before sewing – the jog keys
disappear and the stitch minus/plus keys
appear.

r Return Carriage key

Since this is a very important key to use before
turning off your machine it appears here as
well as in the mode selection window (see
page 10).

Edit

Mode

1

2

3 4

Ready to Sew

A Z

Size

P

A(F): 126 x110m m

00001 ST/NO

Jog

ST

2

1

30 min

5 colors

109x84mm

Snow
White

Seashell

GS
Gray

Green
Dust

5597

5776 5802 5757

q

w

e

r

Rethread and start.

30

Edit

Mode

1 2 3 4

5 6 7 8

Designs

Hoop Size A(F): 126X110mm

A Z

Edit

Font

A Z

AB

OK

M

L

S

AB

Mode

G

H

IJKL

M

N

OP

Q

RST

U

V

W

X

YZ

A

B

C

DEF

Gothic

AB

A(F)

A Z

Edit

Font

A Z

AB

OK

M

L

S

AB

Mode

G

H

IJKL

M

N

OP

Q

RST

U

V

W

X

YZ

A

B

C

DEF

Gothic

AB

A(F)

A Z

How to Select Alphabets

Choose from five different fonts to create text and
monograms.

Touch the “A~Z” key q to open the alphabet
selection window.

Touch the “Font” key

w.

Select one of the fonts by touching its
corresponding key.

Touch the “Return” key e and the font selected will
be indicated.

r Diacritical Letter key

Touch this key to open/close diacritical letters.
(Letters with accents, umlauts, etc.)

t Upper/Lower Case key

Touch this key to switch between lower case
and upper case lettering. See page 32.

q

w

e

r

t

31

q Move Cursor keys

Touch either of these keys to move the cursor
(underline). The cursor location allows you to
edit the text. To add a letter, number or
punctuation (character), move the cursor until
it is under a character. When the new
character is selected it will be inserted on the
left side of the cursor (underlined character).
See page 34.

w Delete key

A character can be deleted if the cursor
(underline) is under it. Use the Move Cursor
keys until the character to be deleted is
underlined. Touch “Delete” key. See page 34.

e Numbers/Punctuation key

Touch this key to switch between letters and
numbers/punctuation keys.

r Horizontal/Vertical key

Touch this key to switch the embroidery
direction between horizontal and vertical. See
page 33.

t Alphabet Size key

Touch this key to switch between large,
medium and small size lettering. This key will
not be active if the font selection is 2 or 3
letters.

y Magnifier key

Touch this key to enlarge the keys so they are
easier to select. Touch the “Return” key to go
back to regular sized keys.

u OK key

When all characters have been selected,
touch this key to proceed to the ready to sew
window.

i Save File key

Touch this key to save your selections in a file
for future use. See page 42.

o Mode key

See page 10.

Font

OK

M

L

S

G

H

IJKL

M

N

O

P

Q

RST

U

V

W

X

YZ

A

B

C

DEF

A Z

AB

Edit

Font

A Z

AB

OK

M

L

S

AB

Mode

G

H

IJKL

M

N

OP

Q

RST

U

V

W

X

YZ

A

B

C

DEF

Gothic

AB

A(F)

A Z

q

we

r

t

y

u

i

o

32

Edit

Mode

Ready to Sew

A Z

Size

P

A(F): 126x 110mm

3 min

Jog

ST

Color
Change

1 color

2

43x18mm

Edit

Font

A Z

AB

OK

M

L

S

AB

Mode

G

H

IJKL

M

N

OP

Q

RST

U

V

W

X

YZ

A

B

C

DEF

Gothic

AB

A(F)

A Z

Edit

Font

A Z

AB

OK

M

L

S

AB

Mode

Gothic

AB

A(F)

Edit

Font

A Z

AB

OK

M

L

S

AB

Mode

Gothic

AB

A(F)

Sewing Alphabets

The alphabet selection window should be open.
See page 30.

Touch the “Font” key and select the Gothic style.
Select “E”.

Touch the “Upper/Lower Case” key to select lower
case.

Select “l”, “n” and “a”.

Touch the “OK” key.

Touch the “Return” key in the hoop size warning
message.

The ready to sew window will open.

q Color Change key

Touch this key if you want the machine to stop
between each letter so that the thread color
can be changed.

q

33

Edit

Mode

Ready to Sew

A Z

Size

P

A(F): 126x 110mm

3 min

Jog

ST

Color
Change

1 color

2

43x18mm

Hoop fabric with the centerlines located on left
side. (Remember the start position for horizontal
alphabets is on the left side of template. See page

23.)

Use the Jog keys q to position hoop and align
needle directly over the centerlines

w.

Lower presser foot. Press “Start/Stop” key and
sew 5 or 6 stitches. Stop machine by pressing
“Start/Stop” key.

Raise presser foot. Cut away beginning thread tail
close to the start point. Lower presser foot.

Press the “Start/Stop” key and let the machine sew
until it stops automatically.

NOTE: Vertical orientation of alphabets would sew
out like illustration

e.

q

w

e

34

Gothic

AB

A(F)

Gothic

AB

A(F)

Gothic

AB

A(F)

Gothic

AB

A(F)

Gothic

AB

A(F)

2

Alphabet Corrections

Deleting a letter

Example: Delete the “3” from “8300”

Touch the “Move Cursor” keys until the cursor
(underline) is under the 3.

Touch the “Delete” key. The “3” is deleted.

Inserting a letter

Example: Insert “2” into 800

Touch the “Move Cursor” keys until the cursor
(underline) is under the number where you want to
insert the new number.

Select “2”. The “2” will be inserted between the “8”
and “0”.

Gothic

AB

A(F)

35

Edit

Font

A Z

AB

OK

M

L

S

AB

Mode

G

H

IJKL

M

N

OP

Q

RST

U

V

W

X

YZ

A

B

C

DEF

2 Letters

AB

A(F)

A Z

Edit

Font

A Z

AB

OK

M

L

S

AB

Mode

G

H

IJKL

M

N

OP

Q

RST

U

V

W

X

YZ

A

B

C

DEF

2

Letters

AB

A Z

A(F)

Edit

Mode

Ready to Sew

A Z

Size

P

A(F): 126x1 10mm

53x62mm

8 min

Jog

ST

Color
Change

2

1 color

Edit

Font

A Z

AB

OK

M

L

S

AB

Mode

G

H

IJKL

M

N

OP

Q

RST

U

V

W

X

YZ

A

B

C

DEF

Gothic

AB

A(F)

A Z

2 Letter or 3 Letter Monograms

Example: 2 letters and frame for crest

The alphabet selection window should be open.
See page 30.

Touch the “Font” key and select “2 Letters” key.

Select one of the frames.

Select “A” and “B”.

Touch “OK” key. Touch the “Return” key in the
hoop size warning message. Sew 2 letter crest.

NOTE: The starting point for 2 letter and 3 letter
monograms is the center of the hoop.

36

Edit

Mode

1 2 3 4

5 6 7 8

Designs

Hoop Size A(F): 126X110mm

A Z

Edit

Mode

PC Card NO.1001
Hoop Size A(F):126x110mm

2

1

3

4

A Z

Sewing with PC Design Cards (Optional)

Inserting the Card

Insert PC design card

q into slot with front side

facing you. Push card in until it clicks and the card
eject button

w pops out. (You should see a red bar

on the button.)

Selecting from a PC Design Card

Touch the “PC Design Card” key e.

The PC design selections window opens. Designs
programmed on the card will appear. Select a
design.

Ejecting the Card

Push in the card eject button. Remove PC design
card from the slot.

CAUTION: Do not turn off the power switch or
eject the card when warning messages or
hourglass icon is displayed.

q

w

e

37

Edit

Mode

1 2 3 4

5 6 7 8

Designs

Hoop Size A(F): 126X110mm

A Z

Edit

Mode

Cancel

OK

Edit

A Z

B: 140x200mm

Size

Edit

Edit

A Z

A(F): 126x110mm

Mode

Cancel

OK

Size

C

A(F)

B

Cancel

OK

B: 140x200mm

C

Edit Window

Modify and combine designs to create your unique
interpretation of them.

Touch the “Edit” key.

The hoop selection window opens. Select one of these
hoops by touching its corresponding key.

q Standard Hoop A or Optional Hoop F –

126 mm x 110 mm (5" x 4 3/8")

w Large Hoop B – 140 mm x 200 mm (5 1/2" x 8")

Optional Free Arm Hoop C – 50 mm x 50 mm (2" x 2")

Touch “OK” key to open the selected hoop edit window.

NOTE: If you touch the “Cancel” key, the large hoop B edit
window will open because the large hoop B is the default
hoop.

NOTE: If you select a design before opening the edit
window, touch the “Hoop Selection” key and use same
method as described above.

Large hoop B edit window

Standard hoop A and Optional hoop F edit window

q

w

e

r

r

e

38

Edit

Mode

Cancel

OK

Edit

A Z

B: 140x200mm

Size

Edit

Mode

1 2 3 4

5 6 7 8

Designs

Hoop Size A(F): 126X110mm

A Z

Edit

A Z

B: 140x200mm

Mode

Cancel

OK

Size

Edit

Selecting a Design After Opening the Edit
Window

Open the design selection window.

Select a design.

The design will appear in the edit window with an
outline surrounding it.

Moving a Design

q Touch the design on the screen and drag it to

the new location with your fingertip. NEVER
drag it with a sharp pointed object.

OR

w Move Design keys

Use these keys to move the design to a new
position. The carriage will not move (like it
does with the jog keys) but instead the design
moves relative to the hoop and not the
machine.

q

w

39

Size

OK

Cancel

100%

Edit

A Z

B: 140x200mm

Mode

Cancel

OK

Size

Edit

Edit

A Z

B: 140x200mm

Mode

Cancel

OK

Size

Edit

Edit

A Z

B: 140x200mm

Mode

Cancel

OK

Size

Edit

q Size key

Touch this key and the size adjustment window will
open. Design size can be changed in 10% increments
between 90% and 120% from the original size.

Touch the “–” key to decrease the design size.
Touch the “+” key to increase the design size.

Touch the “OK” key and the new size of design will
appear in the edit window. (If you touch the “Cancel”
key, size window closes and design remains at original
size.)

w Mirror Image key

Touch this key to flip the design from left to right.

e Face to Face key

Touch this key to flip the design from top to bottom.

r Rotate key

Touch this key to rotate the design 45 degrees
clockwise.

t Delete key

The design that is surrounded by the outline will be
deleted.

y Magnifier key

Touch this key to view the design in a larger image.
Touch “Return” key to close window.

OK key

All designs are grouped together and the ready to sew
window opens.

Cancel Key

Touch this key and all designs in the edit window will be
deleted and edit mode is deactivated.

q

e

w

r

t

y

u

i

u

i

40

Edit

Mode

1

2

3 4

Ready to Sew

A Z

Size

P

A(F): 126x110mm

46x42mm

6 colors

Jog

ST

10 min

2

18

Seashell

5776

Wicker

5789 Date 5590

Visor
Gold

5698

Edit

Mode

Cancel

OK

Edit

A Z

Size

Bear

A(F): 126x110mm

Edit

Mode

Designs

Hoop Size A(F): 126X110mm

A Z

18

17

19 20

21 22 23 24

Edit

Font

A Z

AB

OK

M

L

S

AB

Mode

G

H

IJKL

M

N

OP

Q

RST

U

V

W

X

YZ

A

B

C

DEF

Gothic

AB

A(F)

AA

ZZ

B

Combine a Built-in Design with Alphabet

Example: Built-in design #18 and “Bear”

Select design #18 from the built-in design
selection window.

Touch the “Return” key in the hoop size warning
message.

Touch the “Edit” key.

Touch the “Alphabets” key.

Select “B” (upper case in Gothic style).

Touch the “Upper/Lower Case” key to activate
lower case.

Edit

Font

A Z

AB

OK

M

L

S

AB

Mode

Gothic

AB

A(F)

B

41

Select the “e”, “a” and “r”.
Touch the “OK” key.

Position design and text by either dragging or using the
move design keys. Touch “OK” key to group everything
and open the ready to sew window.

Touch the “Return” key in the hoop size warning
message.

The ready to sew window opens.

Sew design.

NOTE: If you touch the “Return” key in the ready to
sew window, edit mode is deactivated and all data is

deleted.

Edit

Mode

Cancel

OK

Edit

A Z

Size

A(F): 126x110mm

Edit

Mode

1

2

3 4

Ready to Sew

A Z

Size

P

A(F): 126x1 10mm

6 colors

Jog

ST

2

13 min

49x63mm

Seashell

5776

Wicker

5789

Date

5590

Visor
Gold

5698

Edit

Font

A Z

AB

OK

M

L

S

AB

Mode

Gothic

AB

A(F)

B

ear

q

q

42

Edit

Mode

Cancel

OK

Edit

A Z

Size

Bear

A(F): 126x110mm

Save File (Built-in)

M_001

Cancel

OK

Built-in

Card

File Name

Cancel

A

B

C

DEF

G

HI JKLM

N

OPQR

STU

0

1

2

7

8

9

3

456

VWX

YZ

OK

B

E

A

K

Saving a Design in a File

(Edit key must be activated)

q Save File key

Touch this key if you want to save your unique
combination so it can be used in the future.

The save file window will open.

Select the location of where the file will be saved
by touching the “Built-in/Card” key w.

• Built-in: the file will be saved in the internal
memory of the machine.

• Card: the file will be saved onto the PC
card.

File names are automatically assigned in
numerical order, beginning with M_001.

Touch the “File Name” key e to label the file with a
different name.

Touch the keys (up to 8 characters) that
correspond to the file name you wish to assign.

To correct the last character in the name, touch the
“Backspace” key r.

Touch the remaining keys to complete file name.

Cancel

A

B

C

DEF

G

HI JKLM

N

OPQR

STU

012
789

3

456

VWX

YZ

OK

B

E

A

R

1

q

w

e

r

r

43

Short of memory space,

the file cannot be saved.

The same file name exists,

overwrite it?

Cancel

OK

Touch the “OK” key. The file name window will
close and the file will be saved with that name. (If
you touch the “Cancel” key, the file name window
will close without assigning the new file name.)

NOTE: Should you try to save a file under a name
that already exists, this warning message will
appear. Touch “OK” key to overwrite the file. Touch
“Cancel” key if you don’t want to overwrite the file.
Change the file name and then save it under the
new name.

NOTE: When the memory is full, a warning
message will appear. Touch the “OK” key. Go to
the open file window (see page 44) and delete a
file you no longer want.

q Next and Previous keys

The save file window will display 5 saved file
names at a time. Touch these keys to view the
other saved file names.

Touch the “OK” key to save the file. Touch
“Cancel” key to close the save file window without
saving the file.

CAUTION: Do not turn off the power switch or
eject the card when warning messages or
hourglass icon is displayed. The stored data could
be lost or damaged.

Save File (Built-in)

Built-in

Card

File Name

M_00

2

M_001

BEAR

_

1

M_00

3

M_00

5

M_00

4

Cancel

OK

q

Cancel

A

B

C

DEF

G

HI JKLM

N

OPQR

STU

012
789

3

456

VWX

YZ

OK

B

E

A

R

1

44

Opening a Saved File

You can sew any design that has been saved in a
file.

Touch the “Mode” key. Touch the “Open File” key

q.

Open file window will open.

Touch the “Built-in/Card” key w and select the
location of the file directory.

Touch the “File Up/Down” keys e to select the file
you want to open. It will appear in the active name
window .

The open file window will display 5 saved file
names at a time. Touch the next and previous keys

t to view the other saved file names.

Select the file you want to sew. Touch the “OK”
key. The file will appear either in the edit window
or ready to sew window depending on where you
accessed the open file key.

Deleting a Saved File

Display the file you want to delete in the active
name window .

Touch the “Delete” key y.

The confirmation window will open. Touch the “OK”
key to delete. Touch “Cancel” key to close the
confirmation window without deleting the file.

Mode

Are You Sure Y ou W ant

to Delete this File?

OK

Cancel

Open File(Built-in)

Cancel

OK

Built-in

Card

M_002

M_002

M_001

BEAR

_

1

q

w

e

r

t

y

r

r

45

Embroiderying with Optional Free Arm Hoop C

The dimension of the leg or sleeve opening must be
large enough to allow the hoop to move freely. Insert
the innner hoop of large hoop B into the opening
. If the inner hoop cannot be easily inserted, the
opening is too narrow for free arm embroidery.

Maximum distance for design position inside the
opening from the edge is 200mm (77/8”) .
Draw centerlines for design placement.

Remove extension table. See page 5.

Select hoop “C” in Edit Mode.

Select design or letters (dimensions or design/
letters must be 49mm or less).
NOTE: Built-in designs less than 49mm are 3, 9, 18,
20, 21, 22, 23, 24, 29, 30, 34, 35, 36 and 44.

Hoop fabric, aligning centerlines with hoop
template .

Place fabric around free arm and lock hoop onto
carriage. Roll up fabric edges so it will not be caught
at the neck of the free arm during embroidery sew­ing.

Insert the blocking plate (stored in the arm of the
hoop) next to the hoop opening. The blocking
plate prevents the fabric edge on the free arm from
rolling back into the embroidery area.

Touch the “Jog” keys to position needle directly over
centerline.

Sew design.

CAUTION: Immediately remo ve hoop from free arm
after sewing is completed. Never atempt to select a
new design, change modes or switch off machine
without first removing the hoop from the arm.

q

w

e

r

y

t

w

q

e

r

r

t

y

y

46

Taking Care of Your Machine

The machine is self-lubricating, however, the area
around the bobbin and hook must be cleaned each
time the machine has had extensive use. Do not

dismantle the machine further than explained
on these pages. Clean the outside of the machine

with a soft cloth and pure soap.

Cleaning the Hook Area

Loose threads and dust may cause puckered
stitches and thread breakage during stitching.
Check for lint buildup after each project is
completed.

Hand turn the flywheel to raise the needle to its
highest position. Turn Off power switch. Unplug
the machine before cleaning.

Remove the needle. Use the screw key q supplied
with the machine to remove the screw w. Lift away
the needle plate e.

Take out the bobbin. Lift up and remove the bobbin
case r.

Clean the bobbin case with the lint brush and soft,
dry cloth.

Clean the hook area t with the lint brush.
Wipe out gently with soft, dry cloth. (You can also
use a small vacuum cleaner.)

q

w

e

r

t

47

Replacing the Bobbin Case

Insert the bobbin case so the knob q fits next to
the stopper w in the hook area.

Attach the needle plate and tighten the screw.

After cleaning, be sure to replace the needle,
presser foot and bobbin.

Changing the Light Bulb

Turn OFF the power switch. Unplug the machine.
Wait until the bulb has cooled before touching it.

Remove screw cap q and set screw w. Pull away
face plate e.

Pull out light bulb t from the socket r.

Insert light bulb into light socket.

Replace face plate, screw and screw cap.

NOTE: Only use same type light bulb rated 12
Volts, 5 watts.

q

w

e

q

w

t

r

48

2

1

34

20191817

9

10 11 12

65 78

2423

22

21

13

14 15 16

26

25

27

28

44434241

33 34 35 36

30

29

31

32

48474645

52515049 56555453

58

57

37

38

39 40

STITCH CHART

Built-in designs

49

Gothic

Script

Cheltenham

3-letters / 2-letters

50

Condition

Needle thread breaks

Bobbin thread breaks

Needle breaks

Skipped stitches

Designs are distorted

Machine does
not work

Abnormal noise when
machine is turned on

LCD Touch Screen
is not visible

Noisy operation

Selection keys

don’t work

Cause

1.The needle is not threaded properly.

2. The needle thread tension is too tight.

3. The needle is bent or blunt.

4. The needle is not inserted correctly.

5. The needle thread and bobbin thread are not
set in the thread holder before sewing starts.

1. The bobbin thread is not threaded correctly in
the bobbin case.

2. Lint has collected in the bobbin case.

3. The bobbin is damaged and does not turn
smoothly.

1. The needle is not inserted correctly.

2. The needle is bent or blunt.

3. The needle clamp screw is loose.

4. The needle thread tension is too tight.

1. The needle is not inserted correctly.

2. The needle is bent or blunt.

3. The needle thread is not threaded properly.

4. The hoop is not attached correctly to the
carriage.

5. Fabric is not taut in the hoop.

6. Stabilizer is not being used.

1. Fabric is not taut in the hoop.

2. The hoop is not attached correctly to the
carriage.

3. The carriage is hitting into something around
the machine.

4. Fabric is caught or pulled by something
during sewing.

5. The needle thread tension is too tight.

6. Stabilizer is not being used.

7. The thread on the underside of fabric is not
cut correctly.

1. The machine is not plugged in.

2. A thread is caught in the hook area.

3. The control circuit is not working correctly.

1. Something is caught between the carriage
and arm.

2. The carriage is touching something around
the machine.

1. Screen contrast is not adjusted correctly.

2. Machine has not been used for a time and
enters eco mode.

1. Threads have been caught in the hook area.

2. Lint has built up in the bobbin case or hook
area.

1. Keys are not aligned correctly.

2. The control circuit is not working correctly.

See page (s)

18
6
21
21
20

17
46-47

Change bobbin

21
21
21
6

21
21
18
25

24
22

24
25

8
Free up fabric
6

22
Cut thread

7
46-47
Turn machine off and on

Remove object
8

11
11

46-47
46-47

12
Turn machine off and on

TROUBLE SHOOTING

51

INDEX

A

Accessories ............................................................................ 4

Accessory Storage ................................................................. 5

Adjust Key Positions ............................................................. 12

Alphabet Selection Window.................................................. 32

Alphabet Size Key ............................................................... 31

Alphabets............................................................................. 30

B

Backspace Key ..................................................................... 42

Bobbin

Drawing Up Bobbin Thread ............................................... 20

Inserting the Bobbin .......................................................... 17

Winding a Bobbin .......................................................... 15-16

Bobbin Case ..............................................................17, 46-47

Built-in Designs..................................................... 9, 26, 48-49

C

Cancel Key ........................................................................... 27

Card Eject Button ............................................................ 3, 36

Card Slot.......................................................................... 3, 36

Carriage ....................................................................... 3, 8, 25

Centerlines............................................................... 23, 28, 33

Centimeter Measurements .................................................. 11

Changing Needles ............................................................... 21

Cleaning.......................................................................... 46-47

Color Change Key ............................................................... 32

Color/Part Key...................................................................... 26

Combining Designs ........................................................ 37-41

Connecting Machine to Power Supply .................................. 7

Correcting Alphabets ........................................................... 34

Cutting Threads ................................................................... 28

D

Delete Key ..................................................................... 31, 39

Deleting a Saved File .......................................................... 44

Design Chart................................................................ 3, 48-49

Diacritical Letter Key............................................................ 30

E

Eco Mode.............................................................................. 11

Edit................................................................................... 37-39

F

Fabric ....................................................................... 22, 23, 26

Face Plate......................................................................... 3, 47

Face to Face Key ................................................................. 39

Factory Default Settings ...................................................... 13

File Names........................................................................... 42

File Up/Down Keys ............................................................... 44

Files

Saving, Overwriting, Recalling and Deleting.......... 10, 42-44

Flywheel............................................................................ 3, 18

Font Key................................................................................ 30

Format.................................................................................. 13

Free Arm ........................................................................... 5, 45

Function Keys ........................... 9-14, 26-27, 29-32, 38-39, 44

H

Hook Area............................................................................ 46

Hoop Selection Window........................................................ 37

Hoop Tightening Screw ................................................. 22, 24

Hoop T urn key................................................................ 22, 25

Hoops..................................................... 4, 9, 22, 23-25, 37,45

Horizontal/Vertical Key ........................................................ 31

I

Inch Measurements .............................................................. 11

Index Window ....................................................................... 14

Inner Hoop ..................................................................... 22, 24

J

Jog keys......................................................................... 27, 33

Jog/ST Key .......................................................................... 29

K

Keys .......................................... 9-14, 26-27, 29-32, 38-39, 44

L

LCD Screen Contrast .......................................................... 11

LCD T ouch Screen........................................................ 3, 9, 11

Language Selection.............................................................. 13

Letters/Numbers .................................................................. 30

Light Bulb.......................................................................... 1, 47

M

Magnifier Key................................................................. 31, 39

Maintenance ................................................................... 46-47

Memory Bank....................................................................... 13

Mirror Image Key .................................................................. 39

Mode Key......................................................................... 9, 10

Mode Selection Window ...................................................... 10

Monograms..................................................................... 30, 35

Move Cursor Keys ............................................................... 31

Move Design Keys ................................................................ 38

Moving Designs ................................................................... 38

N

Needle Plate ........................................................... 1, 3, 46-47

Needle Position.................................................................... 27

Needle Threader.............................................................. 3, 19

Needles.......................................................................... 19, 21

Next key ..................................................................... 9, 26, 43

Numbers/Letters .................................................................. 30

Numbers/Punctuation Key................................................... 31

O

OK Key ................................................................................. 31

On Screen Information key............................................. 10, 14

Open File key.................................................................. 10, 44

Outer Hoop .................................................................... 22, 24

Overwriting Saved File ........................................................ 43

P

PC Design Card......................................................... 3, 13, 36

PC Design Card Slot ................................................. 3, 13, 36

Part Names............................................................................ 3

Plugs .............................................................................. 1, 3, 7

Power/Light Switch ............................................................. 3, 7

Presser Foot .................................................................... 3, 27

Presser Foot Lever ............................................................ 3, 5

Previous Key .................................................................... 9, 43

R

Ready to Sew Window.................................................... 29, 32

Recalling Saved File............................................................ 44

Register Key .................................................................. 11, 13

Reset to Factory Defaults..................................................... 13

Return Carriage Key....................................................... 10, 29

52

Return Key...................................................................... 10, 27

Rotate Key ........................................................................... 39

S

Save File Key................................................................. 31, 42

Saving a File .................................................................... 42-43

Screen Contrast................................................................... 11

SET Preference Key .................................................. 10, 11-13

Sewing Light .................................................................. 12, 47

Size Key ............................................................................... 39

Size of Design - Dimensions ............................................... 27

Skipping ............................................................................... 26

Small Area – Embroidery ............................................... 26,45

Sound................................................................................... 11

Speed................................................................................... 12

Spool Pins..................................................................... 3, 4, 15

Stabilizers ............................................................................ 22

Start/Stop Key.............................................................. 3, 8, 28

Stitch Minus/Plus Keys ........................................................ 29

T

Template Sheets .............................................................. 4, 28

Templates....................................................................... 23, 24

Thread.................................................................................. 13

Thread Breaks ..................................................................... 29

Thread Cutting ................................................................. 3, 28

Thread Holder.................................................................. 3, 20

Thread Tension ............................................................ .3, 6, 27

Threading........................................................................ 14, 18

Time ..................................................................................... 27

Trace Key ............................................................................. 27

U

Upper/Lower Case Key........................................................ 30

V

Vertical Orientation .............................................................. 33

W

Window category ................................................................... 9