Elmo Ceiling Presenter HV-C1000XG Instruction Manual

CEILING PRESENTER

HV-C1000XG

INSTRUCTION MANUAL

Please read this instruction manual carefully before using this product and keep it for future reference.

1

IMPORTANT SAFEGUARDS

■ Read Instructions – All the safety
and operating instructions should be
read before the appliance is
operated.

■ Retain Instructions – The safety and
operating instructions should be
retained for future reference.

■ Heed Warnings – All warnings on
the product and in the operating
instructions should be adhered to.

■ Follow Instructions – All operating
and use instructions should be
followed.

■ Cleaning – Unplug this product
from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for
cleaning.

■ Attachments – Do not use
attachments not recommended by the
product manufacturer as they may
cause hazards.

■ Water and Moisture – Do not use
this product near water - for example,
near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet
basement, or near a swimming pool,
and the like.

■ Accessories – Do not place this
product on an unstable cart, stand,
tripod, bracket, or table. The product
may fall, causing serious injury to a
child or adult, and serious damage to
the product. Use only with a cart,
stand, tripod, bracket, or table
recommended by the manufacturer, or
sold with the product. Any mounting
of the product should follow the

manufacturer's instructions, and
should use a mounting accessory
recommended by the manufacturer.

■ Ventilation – Slots and openings in
the cabinet are provided for
ventilation and to ensure reliable
operation of the product and to
protect it from overheating, and these
openings must not be blocked or
covered. The openings should never
be blocked by placing the product on
a bed, sofa, rug, or other similar
surface. This product should not be
placed in a built-in installation such as
a bookcase or rack unless proper
ventilation is provided or the
manufacturer's instructions have been
adhered to.

■ Power Sources – This product
should be operated only from the type
of power source indicated on the
marking label. If you are not sure of
the type of power supply to your
home consult your appliance dealer
or local power company. For products
intended to operate from battery
power, or other sources, refer to the
operating instructions.

2

■ Grounding or Polarization – This
product may be equipped with either
a polarized 2-wire AC line plug (a
plug having one blade wider than the
other) or a 3-wire grounding type
plug, a plug having a third
(grounding) pin. The 2-wire polarized
plug will fit into the power outlet only
one way. This is a safety feature. If
you are unable to insert the plug fully
into the outlet, try reversing the plug.
If the plug still fails to fit, contact your
electrician to replace your obsolete
outlet. Do not defeat the safety
purpose of the polarized plug. The 3­wire grounding type plug will fit into
a grounding type power outlet. This is
a safety feature. If you are unable to
insert the plug into the outlet, contact
your electrician to replace your
obsolete outlet. Do not defeat the
safety purpose of the grounding type
plug.

■ Power-Cord Protection – Power­supply cords should be routed so that
they are not likely to be walked on or
pinched by items placed upon or
against them, paying particular
attention to cords at plugs,
convenience receptacles, and the
point where they exit from the
product.

■ Lightning – For added protection
for this product during a lightning
storm, or when it is left unattended
and unused for long periods of time,
unplug it from the wall outlet and
disconnect the antenna or cable
system. This will prevent damage to
the product due to lightning and
power-line surges.

■ Overloading – Do not overload
wall outlets, extension cords, or
integral convenience receptacles as
this can result in a risk of fire or
electric shock.

■ A product and
cart combination
should be moved
with care. Quick
stops, excessive
force, and uneven
surfaces may cause the product and
cart combination to overturn.

■ Object and Liquid Entry – Never
push objects of any kind into this
product through openings as they
may touch dangerous voltage points
or short-out parts that could result in a
fire or electric shock. Never spill
liquid of any kind on the product.

■ Servicing – Do not attempt to
service this product yourself as
opening or removing covers may
expose you to dangerous voltage or
other hazards. Refer all servicing to
qualified service personnel.

WARNING : Handling the

cord on this product or
cords associated with
accessories sold with this
product, will expose you to
lead, a chemical known to
the State of California to
cause birth defects or
other reproductive harm.

Wash hands after
handling.

3

■ Damage Requiring Service –
Unplug this product from the wall
outlet and refer servicing to qualified
service personnel under the following
conditions:

● When the power-supply cord or
plug is damaged.

● If liquid has been spilled, or
objects have fallen into the
product.

● If the product has been exposed
to rain or water.

● If the product does not operate
normally by following the
operating instructions. Adjust
only those controls that are
covered by the operating
instructions as an improper
adjustment of other controls
may result in damage and will
often require extensive work by
a qualified technician to restore
the product to its normal
operation.

● If the product has been dropped
or damaged in any way.

● When the product exhibits a
distinct change in performance ­this indicates a need for service.

■ Replacement Parts – When
replacement parts are required, be
sure the service technician has used
replacement parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may result
in fire, electric shock or other
hazards.

■ Safety Check – Upon completion of
any service or repairs to this product,
ask the service technician to perform
safety checks to determine that the
product is in proper operating
condition.

■ Heat – The product should be
situated away from heat sources such
as radiators, heat registers, stoves, or
other products (including amplifiers)
that produce heat.

■ Wall or Ceiling Mounting - The
product should be mounted to a wall
or ceiling only as recommended by
the manufacturer.

■ When the lamp is ON, don't touch
the lamp or lamp cover.Negligence
could result in burned injury.

■ Don't use this outdoors.Negligence
could result in electric shock or fire.

CAUTION

RISK OF

ELECTRIC SHOCK

DO NOT OPEN

CAUTION:
TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK).
NO USER-SERVICEABLE
PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.

4

The lightning flash with
arrowhead symbol, within an
equilateral triangle, is intended
to alert the user to the presence
of uninsulated "dangerous
voltage" within the product's
enclosure that may be of
sufficient magnitude to constitute
a risk of electric shock to
persons. This marking is located
at the bottom of product.

The exclamation point within
an equilateral triangle is
intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
product.

SA 1965

SA 1966

WARNING:
TO REDUCE THE RISK
OF FIRE OR ELECTRIC
SHOCK, DO NOT
EXPOSE THIS
PRODUCT TO RAIN OR
MOISTURE.

THIS IS A CLASS A
PRODUCT.
IN A DOMESTIC
ENVIRONMENT THIS
PRODUCT MAY CAUSE
RADIO
INTERFERENCE IN
WHICH CASE THE
USER MAY BE
REQUIRED TO TAKE
ADEQUATE MEASURES.

INFORMATION

This equipment has been tested
and found to comply with the
limits for a Class A digital
device, pursuant to Part 15 of
the FCC Rules. These limits are
designed to provide reasonable
protection against harmful
interference when the equipment
is operated in a commercial
environment. This equipment
generates, uses, and can
radiate radio frequency energy
and, if not installed and used in
accordance with the instruction
manual, may cause harmful
interference to radio
communications. Operation of
this equipment in a residential
area is likely to cause harmful
interference in which case the
user will be required to correct
the interference at his own
expense.

USER-INSTALLER
CAUTION:

Your authority to operate this
FCC verified equipment could
be voided if you make changes
or modifications not expressly
approved by the party
responsible for compliance to
Part 15 of the FCC rules.

5

BEFORE YOU USE

■ Use this product under the rated electrical conditions.

■ Do not leave this product under direct sunlight or by heaters, or this

product may be discolored, deformed, or damaged.

■ Do not place this product in any humid, dusty, windy or vibrating
location. Use this product in the following environmental conditions:
Temperature: 5°C~40°C (41°F~104°F)
Humidity: 30%~85% (No condensation)

■ Use a soft, dry cloth for cleaning. Do not use any volatile solvent, such
as thinner or benzine.

■ Do not directly point the camera lens into the sun, or the camera may be
damaged.

■ Although this product is equipped with a lamp, it is not a lighting
system.
Do not use this product primarily as a lighting unit. Such use may cause
fire or accident.

■ Caring for the batteries:

• If this product is not used for a long time, take out the batteries from

the wireless remote control.

• Do not use rechargeable Ni-Cd batteries.

• Do not use new and old batteries, or batteries of different types

together.

• Do not try to recharge or short-circuit the batteries.

1. PART NAMES
AND FUNCTIONS

2.

WIRELESS REMOTE

CONTROL

3. MOUSE

4. INSTALLATION

5. OPERATION
PROCEDURES

6.

VARIOUS FUNCTION

AND OPERATIONS

7. OSD7. OSD

8. RS-232C
SPECIFICATIONS

9. REPLACING
THE LAMP

10.

TROUBLESHOOTING

HINTS

11. SPECIFICATIONS

CONTENTS

6

1. PART NAMES AND FUNCTIONS

Appearance .......................................................8

Connector Panel..................................................9

Wireless Remote Control .....................................10

2. WIRELESS REMOTE CONTROL

Receivable Range ..............................................12

Preparation ......................................................12

3. MOUSE

Mouse Operation ..............................................13

4. INSTALLATION

Installation of the Unit

............................................14

Setting of Auto Focus Operating Range...................14

Connection to Monitor and Projector ......................15

Connection to the analog RGB-out terminal .....................15

Connection to the composite video-out terminal................15

Connection to the S video-out terminal ...........................15

5. OPERATION PROCEDURES

Simple Steps for Presenting Printed Material .............16

6.

VARIOUS FUNCTIONS AND OPERATION

Lighting ...........................................................17

Zoom..............................................................17

Digital Magnification..........................................18

Color / B&W Selection ......................................19

Posi / Nega Conversion .....................................20

Image Rotation..................................................20

Pause..............................................................21

Contrast ..........................................................21

F.A.M. (Frame Accumulate Mode)..........................22

Iris .................................................................22

Auto iris adjustment ...................................................22

Focus..............................................................23

Auto Focus ..............................................................23

Powered Manual Focus ..............................................24

Preset Operation ...............................................25

Image Memory..................................................26

"Utility Software CD-ROM" ...................................26

7. OSD (On-Screen Display)

OSD Operation.................................................27

Main Menu ......................................................28

Sub Menu ........................................................30

11

1

2

3

4

5

6

7

8

9

10

1. PART NAMES
AND FUNCTIONS

2.

WIRELESS REMOTE

CONTROL

3. MOUSE

4. INSTALLATION

5. OPERATION
PROCEDURES

6.

VARIOUS FUNCTION

AND OPERATIONS

7. OSD

9. REPLACING
THE LAMP

10.

TROUBLESHOOTING

HINTS

11. SPECIFICATIONS

CONTENTS

8. RS-232C
SPECIFICATIONS

7

8. RS-232C SPECIFICATIONS

Setting Up........................................................32

Cable Connection..............................................32

Connection ......................................................33

Transmission Specifications ..................................33

Data Format Specifications...................................33

Transmission command (PC → Ceiling Presenter) ..............33

Response data format (Ceiling Presenter → PC)................34

UART Communication Format................................35

9. REPLACING THE LAMP

Replacing the Lamp ............................................37

10. TROUBLESHOOTING HINTS

Symptoms and Confirmation .................................38

11. SPECIFICATIONS

General..................................................................39

Camera..................................................................40

Lighting ..................................................................40

Supplied Accessories.................................................41

Optional parts (to be purchased separately) ....................41

11

1

2

3

4

5

6

7

8

9

10

11

8

Appearance

Ceiling mounting screw hole

Lamp cover

Ventilation outlet

Setscrew

Halogen lamp

Infrared ray receptor

LED

Lens

1 PART NAMES AND FUNCTIONS

1

2

3

4

5

6

7

8

9

10

11

9

1

2

3

4

5

6

7

8

9

10

Connector Panel

Mouse
Terminal
[MOUSE]

USB Terminal
[

USB

]

Video-out Terminal [S-VIDEO/VIDEO]
S-Video (Mini DIN 4P)

Composite Video (RCA pin jack)

RS-232C Terminal
[

RS-232C

]

Analog RGB-out
Terminal [RGB OUT]

DIP Switches

Power Cord
Receptacle[AC IN

]

Power Supply Switch
[

POWER

]

ABCD

0
1

Name Function Reference Page

1

2

4

3

5

6

P. 32

P. 15

P. 13

P. 26

P. 14 P. 15

P. 15

Mouse Terminal [MOUSE]

USB Terminal [USB

]

Video-out Terminal
[S-VIDEO/VIDEO]
S-Video (Mini DIN 4P)
Composite Video
(RCA pin jack)

RS-232C Terminal
[

RS-232C

]

Analog RGB-out
Terminal
[RGB OUT]

To connect the mouse (supplied accessory)(*1).

If connected to personal computer with
the attached USB cable, it is possible to
transfer images and control the unit by
using the software in the attached Utility
Software CD-ROM.(*1

)

To output images to the NTSC/PAL
monitor, such as TV monitor.

Image is output when this terminal is
connected to RGB input equipment
(e.g., LCD projector, multi-sync monitor).

To connect the RS-232C cable when
controlling the unit from the PC.

DIP Switches

0

[A] key

Over scan

Key alignment and functions:

Under scan

NTSC

PAL

[B] key [D] key[C] key

1

The functions can be changed as follows:

◊

[A] key: To change the video output type.

◊

[B] key: To change the screen size of video output.

◊

[C] key: Selects the operating range of AF.

◊

[D] key: Selects the operating range of AF.

Before changing the DIP Switch keys, be
sure to turn OFF the power supply to this
product.

AF range selected

(See P. 14.)

(*1) For cable extension, use a cable specified for extension that is commercially available.

11

10

1

2

3

4

5

6

7

8

9

10

Wireless Remote Control

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

SET

NORMAL OPEN CLOSE

PRESET

CALL

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PAU SE

PRESET.SET

POSI/NEGA

ZOOM.TELE

ZOOM.WIDE

IRIS.NORMAL

IRIS.OPEN

AUTO FOCUS

FOCUS.FAR

FOCUS.NEAR

IRIS.CLOSE

MENU

F.A.M.

LAMP

IMAGE.CALL

IMAGE.SET

CONTRAST

IMAGE ROTATION

PRESET.CALL

COLOR/B&W

2X

2

POWER

1

3

6
7
10

11

14

17

18

22

23

24

21

20

19

16

15

13

12

9

8

MEMORY NO.

ARROWS

5

4

Name Function Reference Page

7

8

Power Cord Receptacle
[

AC IN

]

Connected to the power cord connector.

Power Supply Switch
[POWER]

To turn ON/OFF the power supply.

11

11

1

2

3

4

5

6

7

8

9

10

COLOR/B&W

DIGITAL
MAGNIFICATION

Button Name Function Reference Page

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

To zoom in.

To zoom out.

To move the focus near.

To move the focus far.

To focus automatically.

To reset the AUTO IRIS to the initial value.

To open the AUTO/MANUAL IRIS.

To close the AUTO/MANUAL IRIS.

To change POSI/NEGA.

To change COLOR/B&W.

CONTRAST

To turn ON/OFF the contrast enhancement.

To turn ON/OFF the lamp.

To store images in the unit's memory.
Used with the MEMORY NO.
.

To switch pause/motion of the image.

The memory No. Used with 6 to 9 .

To double the image size.

PAU SE

To turn ON/OFF the power supply.

POWER

STAT US

IMAGE

LAMP

To turn ON/OFF the pointer and the OSD menu.
Determine the OSD menu pointed by the pointer.

MENU

To rotate the image anticlockwise by 90°.

IMAGE ROTATION

To reduce the rough noise of the image.

F.A.M.

ZOOM

FOCUS

IRIS

POSI/NEGA

2X

PRESET.SET

PRESET.CALL

NORMAL

OPEN

CLOSE

TELE

WIDE

NEAR

FAR

AUTO FOCUS

IMAGE.SET

IMAGE.CALL

ARROWS

MEMORY NO.

To scroll the magnified screen. This can
also be used to move the pointer when
the pointer is displayed.

To store the operating condition of the
unit. Used with the MEMORY NO.

To call the stored operating condition.
Used with the MEMORY NO.

To call the image stored by [IMAGE.SET]
button. Used with the MEMORY NO.

P. 21

P. 16

P. 18

P. 25

P. 26

P. 20

P. 19

P. 21

P. 17

P. 27

P. 20

P. 22

P. 17

P. 24

P. 23

P. 22

11

12

1

2

3

4

5

6

7

8

9

10

Receivable Range

Point the infrared emitting part of the wireless remote control at the infrared sensor of this
product, and press the button for desired function. The receivable range may be narrowed or
the light may not be received when this product is placed under sunlight, near an inverter
fluorescent lamp or in any other unfavorable surroundings. Take measures such as shielding
the sunlight and the light from inverter fluorescent lamp.

• Receivable range
Distance : Approx. 7 m (23 ft.) or less from the light receiving area to the front of the

wireless remote control.

Angle : Approx. 30° degrees or less from the light receiving area upward and

downward, approx. 50°degrees or less from the light receiving area
rightward and leftward.

2 WIRELESS REMOTE CONTROL

Preparation

Remove the battery case cover by pressing downward on the [ OPEN] mark part in the
direction as indicated by the arrow.
Install 2 pcs. of batteries (type R03, AAA) into the case in the direction as indicated there.

Install the batteries according to palarity.

Change the batteries once a year.

The batteries supplied with this product are only for use in initially confirming the operation of
this product. It is not guaranteed that these batteries can work effectively for the indicated
period.

11

13

1

2

3

4

5

6

7

8

9

10

Mouse Operation

Connect the mouse to the mouse terminal [MOUSE]
on the connector panel.

• Click the left button
To operate the OSD menu.
When digital magnification or image rotation (90°,
270°) is not used, the pointer and OSD menu can
be displayed/deleted.

•

Drag by left button (moves while button is being pushed)

In time of digital magnification or image rotation
(90°,270°), screen is scrolled.

• Click the mouse wheel
To display or clear the pointer and OSD menu
alternately by clicking.

• Roll the mouse wheel
To scroll the screen up/down when the image is in digital magnification or rotated to 90°
or 270°.

• Click the right button
When this button is clicked for digital magnification while the pointer is displayed,
the position of the pointer is the center of the magnified image.
When the pointer is not displayed, the center position of the image is digitally magnified.

Click the OSD menu, then the menu functions are given priority.

When using the mouse, connect the mouse before turning ON the power supply to this product.

Use the attached mouse. If another mouse is used, the normal operation cannot be guaranteed.
If the cable is extended, use the commercial cable for extension or consult the distributor.

The OSD menu is assumed to be used for large projection sizes with a projector or the like.
Therefore, the display on a hand monitor or a TV may be hard to see.

• Digital Magnification .......

• OSD ...............................

P.27

P.18

Reference Page

3 MOUSE

The pointer
is displayed.

The pointer
is cleared.

The OSD
menu is
displayed.

The OSD
menu is
cleared.

Click Click

Click

Click

Right button

Left button

Center button
Mouse wheel

Mouse

11

14

1

2

3

4

5

6

7

8

9

10

4 INSTALLATION

Setting of Auto Focus Operating Range

The following settings of this product can be changed with the DIP Switches. Change the
settings according to the connection environment. The factory settings are as shown in the
following table:

In delivery from plant, the whole area is set.

When changing the DIP Switch keys, be sure to turn OFF the power supply to this poduct
beforehand.

AF operating range (Shooting distance)

Whole area (1.3m )

1.3m 1.8m

1.7m 2.8m

2.7m

[C] key [D] key

00
10
01

11

Installation of the Unit

For the ceiling mounting metal piece, VB-1000
separately available, any product approved by UL
Standard for projector which is capable of supporting
a load of 8-10 kg or more, or similar product also
approved by UL Standard shall be used. Request your
distributor to install this product on the ceiling. For
details, refer to the HV-C1000XG Installation Manual
included in the package.

Connect the power supply cord with the Power Cord
Receptacle of this product and plug outlet.
Turn ON the Power Supply Switch.

When this product is not used for a long time, turn
OFF the Power Supply Switch or remove the power
supply plug from the outlet.

Provide a distance of 1.3m or more between the
unit and the document to be projected.Images can
be focused when the distance increases; however,
the light intensity may be insufficient.If the distance
is more than 3m, external lighting is needed.

11

15

1

2

3

4

5

6

7

8

9

10

■ Connection to the analog RGB-out terminal

Connect the Analog RGB-out Terminal [RGB OUT] to the equipment with an analog RGB-in
terminal with the analog RGB cable (attached) or a connection cable available on the market.
At this time, the position of the display may be deviated from the center. If deviated, manually
adjust the horizontal and vertical positions on the connected equipment.
Also, vertical stripes may appear on the screen of the LCD projector. That can be alleviated
by manually adjusting the dot clock frequency on the projector.

■ Connection to the composite video-out terminal

Use the Composite Video-out Terminal [VIDEO](RCA pin) and the video cable with RCA pin
plug as attached or available on the market.

■ Connection to the S video-out terminal

Use the S Video-out Terminal [S-VIDEO](Mini DIN 4P) and the S-Video cable as attached or
available on the market.

Hold the cable plug when connecting or disconnecting the cables.

S-VIDEO

USB

MOUSE

RGB OUT

RS-232C

AC IN

POWER

VIDEO

LCD projector

CRT monitor

or

S-VIDEO

USB

MOUSE

RGB OUT

RS-232C

AC IN

POWER

VIDEO

TV monitor

S-VIDEO

USB

MOUSE

RGB OUT

RS-232C

AC IN

POWER

VIDEO

TV monitor

Connection to Monitor and Projector

The following settings of this product can be made with the DIP Switches. Make the settings
according to the connection environment. The factory settings are as shown in the following
table:

Be sure to turn OFF the power supply to all equipment before making any connections to
protect this product and all the connected equipment.

When changing the DIP Switch keys, be sure to turn OFF the power supply to this product
beforehand.

Key

A

B

To change the Video output type
To change the screen size of Video output

Function Key selection

Initial setting

NTSC

Over scan

1
0

Content

11

16

1

2

3

4

5

6

7

8

9

10

Simple Steps for Presenting Printed Material

(1) Push the [POWER] button of the wireless

remote control to turn ON the power (Indicator
LED on the unit turns from red to green).

Connection with the monitor should be done in
advance.

If the Power Supply Switch is turned ON
immediately after it is turned OFF, this product may
not operate.
To restart operation, turn ON the Power Supply
Switch after several seconds.

When the document surface is dark, turn ON the
lamp by pressing the [LAMP] button.

After the power supply is turned ON, it takes
about 10 seconds to execute the initialization of
the unit and output the image.

(2) Place an object on the document surface and

adjust the image size using [ZOOM·TELE] and
[ZOOM·WIDE] buttons on the wireless remote
control as you watch the monitor screen so that
the projected image may be in compliance with
the object.

(3) Adjust the focus by pressing the [FOCUS·N/F]

(NEAR/FAR) buttons of the wireless remote
control. The focus can be also adjusted by
pressing the [AF] (AUTO FOCUS) button.

(4) After finishing the operation, turn OFF the

[POWER] button of the wireless remote control.
(Indicator LED on the unit turns from green to
red.)

NORMAL OPEN CLOSE

TELE

ZOOM

WIDE

NEAR

FOCUS

FAR

AF

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

Wireless remote control

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

WIDE

NEAR

FOCUS

FAR

AF

Wireless remote control

Wireless remote control

5 OPERATION PROCEDURES

(1)

(4)

(2)

(3)

11

17

1

2

3

4

5

6

7

8

9

10

Zoom

Press the [ZOOM.TELE] button on the wireless
remote control, and the image will gradually be
magnified.
Press the [ZOOM.WIDE] button on the wireless
remote control, and the image will gradually be
reduced.
Also, by continuously pressing the ZOOM button, the
zooming speed becomes faster. (Double speed
function)

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

NORMAL OPEN CLOSE

TELE

ZOOM

WIDE

NEAR

FOCUS

FAR

AF

Wireless remote control

Wireless remote control

Lighting

Lighting for presenting information such as printed
materials is provided.
When the [LAMP] button on the wireless remote
control is pressed, the lamp is lit.
When the [LAMP] button is pressed again, the lamp
goes off.

To obtain a sharp image with good color
rendering, it is sometimes necessary to use the
lighting.

When the lighting provided by the unit is
insufficient, use external lighting.

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

MENU

6

VARIOUS FUNCTIONS AND OPERATION

Wireless remote control

Wireless remote control

11

18

1

2

3

4

5

6

7

8

9

10

Digital Magnification

To double the image, press the [2x] button on the
wireless remote control or click the Right button of the
mouse.
Enlarged screen can be scrolled by operating the
arrow button on the wireless remote control or by
operating the mouse.

If the OSD menu is displayed on the digitally
magnified screen, the magnified screen cannot be
scrolled by the wireless remote control.

•

The mouse can be operated
as follows:

• Left button........ To scroll the image

according to the dragging of the
mouse while holding down the left
button.

•

Mouse wheel

.... To scroll up/down the magnified

screen.

• Right button ..... To tu r n ON/OFF the double

enlargement. When any image is
magnified digitally, the pointer
becomes the mark .

When the digital magnification is tried while the
mouse pointer is in display, since the left button of
the mouse is limited to the scroll function, the
mouse pointer and the OSD menu cannot be
turned ON/OFF.
To turn ON/OFF the mouse pointer and the OSD
menu, turn OFF the digital magnification.

• Mouse ................

• OSD....................

P.27

P. 13

Reference Page

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

Wireless remote control

IMAGE

CALLSET

PRESET

CALLSET

Wireless remote control

11

19

1

2

3

4

5

6

7

8

9

10

Color / B&W Selection

To present the B&W (Black&White) material such as
documents. Sharper image with no color blur on the
monitor can be produced.
If the [COLOR/B&W] button on the wireless remote
control is pressed, images are switched.

When PAUSE is effective, COLOR/B&W selection
does not work.

•OSD........

P.27

Reference Page

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

Wireless remote control

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

MENU

Wireless remote control

Posi / Nega Conversion

To show a negative film.
Press the [POSI / NEGA] button on the wireless
remote control, the image will be converted to the
NEGA mode accordingly.
When the [POSI / NEGA] button is pressed again,
the POSI mode is resumed.

When using the NEGA conversion mode, use of
the following is restricted.

• With CONTRAST ON: Gamma adjustment is not
available.

•Only with Gamma setting γ = 07: CONTRAST
can be turned ON.

NEGA setting at the factory

• Gamma: γ = 07 (0.3)

• CONTRAST: ON

When PAUSE is effective, POSI/NEGA conversion
does not work.

11

20

1

2

3

4

5

6

7

8

9

10

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

MENU

Wireless remote control

Wireless remote control

•OSD........

P.27

Reference Page

Image Rotation

When the [IMAGE ROTATION] button on the
wireless remote control is pressed, the image rotates.
Every time the [IMAGE ROTATION] button is
pressed, the image rotates counterclockwise by 90°.

The image does not rotate when PAUSE mode is
working.

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

Wireless remote control

IMAGE ROTATION

F.A.M.

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

Wireless remote control

•OSD........

P.27

Reference Page

11

21

1

2

3

4

5

6

7

8

9

10

Contrast

To present the material with a little half tone such as
texts.
Images with sharp characters and lines contrasty with
background can be obtained.
When the [CONTRAST] button on the wireless
remote control is pressed, the image becomes
contrasty.
When the [CONTRAST] button is pressed again, the
image is reset to the normal condition.

When using NEGA conversion, the CONTRAST
can only be turned ON if Gamma setting is γ =07
(0.3).

CONTRAST does not function while PAUSE is
functioning.

Pause

When the [PAUSE] button on the wireless remote
control is pressed, the image from the unit’s camera
pauses. When the [PAUSE] button is pressed again,
the PAUSE mode is canceled.

When PAUSE is effective, POSI/NEGA
conversion, IMAGE ROATION, COLOR/B&W
selection, F.A.M., and CONTRAST functions do
not work.

Although the ZOOM, FOCUS, and IRIS functions
are effective, the results are not reflected in the
image in this mode.

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

PAUSE

Wireless remote control

Wireless remote control

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

MENU

Wireless remote control

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

Wireless remote control

•OSD........

P.27

Reference Page

•OSD........

P.27

Reference Page

11

22

1

2

3

4

5

6

7

8

9

10

Iris

■ Auto iris adjustment

By adjusting the diaphragm, the brightness will
automatically follow changes of brightness according
to the object.
Press the [IRIS.OPEN] button on the wireless remote
control to open the iris.
Press the [IRIS.CLOSE] button on the wireless remote
control to close the iris.
Press the [IRIS.NORMAL] button on the wireless
remote control, to change setting back to the defaults.

Use RS-232C interface for MANUAL IRIS
operation.

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

IRIS

NORMAL OPEN CLOSE

AF

Wireless remote control

Wireless remote control

•OSD........

P.27

Reference Page

F.A.M. (Frame Accumulate Mode)

This is used to reduce artifacts of the image, and is
appropriate to take pictures of still objects. Press the
[F.A.M.] (Frame Accumulate Mode) button on the
wireless remote control, and the [F.A.M.] is selected.
Press the [F.A.M.] (Frame Accumulate Mode) button
again, and the normal status is resumed.

[F.A.M.] does not function while the image is rotated
or PAUSE is functioning.

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

MENU

Wireless remote control

Wireless remote control

11

23

1

2

3

4

5

6

7

8

9

10

Focus

Adjust the focus of the object.

■ Auto Focus

When the [AF](AUTO FOCUS) button on the
wireless remote control is pressed, the focus is set
automatically.
This product features a one-push AUTO FOCUS
function. Once focusing is completed, the AUTO
FOCUS function is released, and the focused position
maintains unchanged (FOCUSFREE).

The objects listed below may not be brought into
focus in the AUTO FOCUS mode. In these cases,
use the MANUAL FOCUS mode.

• Objects bearing little contrast

•Objects with fine repeated patterns, such as
lateral stripes and cross stripes

• Objects glittering or reflecting strong light

•Objects with bright background, or excessive
contrast

• The whole image is dark.

• Objects located near and far away at the same
time

• Objects in motion

Some objects require a long auto focus time.

When the MANUAL FOCUS buttons ([FOCUS

·NEAR] or [FOCUS·FAR] button) on the.wireless

remote control are pressed,the AUTO FOCUS
operation is reset.

When the ZOOM buttons ([ZOOM·TELE] or
[ZOOM·WIDE] buttons) on the wireless remote
control are pressed, the AUTO FOCUS operation
is suspended.

If some other operation is performed in

AUTO

FOCUS

operation, the

AUTO FOCUS

operation may

not be completed normally.

FOCUS can be adjusted at a distance of 1.3m or
more from the unit to the object in the max. side of
[ZOOM·TELE].

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

IRIS

NORMAL OPEN CLOSE

TELEOOWIDE

NEAR FAR

AF

Wireless remote control

Wireless remote control

•OSD........

P.27

Reference Page

11

24

1

2

3

4

5

6

7

8

9

10

■ Power Manual Focus

To focus on specific part of the material, such as 3-D
material. Press the FOCUS button [FOCUS.NEAR] or

[

FOCUS.FAR] on the wireless remote control.

This product can finely adjust the focus. For minor
adjustments, press the FOCUS button several times.
For major adjustments, keep the FOCUS button
pressed, then the focus begins to move more
quickly.

Focus can be adjusted at a distance of 1.3 m or
more from the unit to the object in the max. side of

[ZOOM

.

TELE].

NORMAL OPEN CLOSE

TELE

ZOOM

WIDE

NEAR

FOCUS

FAR

AF

Wireless remote control

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

Wireless remote control

•OSD........

P.27

Reference Page

25

1

2

3

4

5

6

7

8

9

10

11

Preset Operation

Operation status of this product can be stored / read
out in the memory (max. 8 states can be stored).
Operation states that can be stored are as shown
below.

•Present zoom angle of view

•Status of IRIS

•White Balance status

•ON/OFF of Aperture

•Status of Gamma

•Lighting status

•Status of COLOR/B&W switch

•Condition including pointer ON/OFF, color and

shape

•Condition of IMAGE ROTATION

•ON/OFF of CONTRAST mode

•Status of POSI/NEGA conversion

•Status of F.A.M. selection

1. How to store

Press the [PRESET.SET] button on the wireless
remote control and press the MEMORY NO.
button of the wireless remote control within 4 sec
then the current status of this product is saved in
the pressed number memory.

The preset (stored) status is maintained even when
the power is turned OFF.

2. How to read out operation status

Press the [PRESET.CALL] button on the wireless
remote control and press the MEMORY NO.
button of the wireless remote control within 4 sec
then this product is set to the memorized status
corresponding to the number.

CONTRAST

LAMP

POSI/NEGA COLOR/B&W

IMAGE

CALLSET

PRESET

CALLSET

Wireless remote control

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

Wireless remote control

•OSD........

P.27

Reference Page

26

1

2

3

4

5

6

7

8

9

10

11

Image Memory

Images can be stored / called in the memory of this
product (max. 8 images).

1. Press the [IMAGE.SET] button on the wireless

remote control and press the MEMORY NO.
button of the wireless remote control within 4 sec
then the image is stored in the pressed number.

When the Power Supply is turned OFF by pressing
the [POWER] button of the wireless remote
control, the images stored in the memory are
deleted.

2. How to read out stored images

Press the [IMAGE.CALL] button on the wireless
remote control and press the MEMORY NO. button
of the wireless remote control within 4 sec then the
image in the memory corresponding to the pressed
number is read out.

To return to the normal camera image, press the

[IMAGE

.

CALL] button again “within 4 seconds”.

The image cannot be saved in the number from
which the image is read.

"Utility Software CD-ROM"

The attached "Utility Software CD-ROM" contains the PC link software "Image Mate" and the
TWAIN driver "ELMO TWAIN DS, "and can be operated as shown below.

• To transfer graphic data to PC.

• To operate this product by PC.

For details, see the Installation Manual for "Utility Software" and "manual.pdf" in the CD­ROM.

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

CONTRAST

LAMP

POSI/NEGA COLOR/B&W

IMAGE

CALLSET

PRESET

CALLSET

Wireless remote control

Wireless remote control

•OSD........

P.27

Reference Page

11

27

1

2

3

4

5

6

7

8

9

10

7 OSD (On-Screen Display)

OSD (On-Screen Display) means the operating menu displayed on the screen (hereinafter
called OSD menu).
The OSD menu is operable by the wireless remote control or mouse.

OSD Operation

1. When the [MENU] button on the wireless remote

control is pressed, a pointer is displayed.

2. If the [MENU] button is pushed again, the OSD

menu is displayed, and the pointer moves to the
lower left area of the OSD menu.

3. Move the pointer to the required icon. The pointer
can be moved by pushing the ARROW buttons.
(Same as MEMORY NO. buttons for image
memory/PRESET operation.)

4. When the [MENU] button is pressed, the icon is
pressed and the corresponding operation is
executed.

5. To end the OSD menu, keep pushing the up/down
ARROW button to move the pointer out of the
OSD area. Then push the [MENU] button, and
the OSD menu goes off. If the [MENU] button is
pushed again, the pointer goes off.

While the OSD menu is on the display, the pointer
of the wireless remote control moves only on the
icons in the OSD menu. (Color of icons is turned
red).
If the sub-menu is displayed, the pointer moves
only on the functional items. To move to another
icon, close the sub-menu, and move the pointer.

When a pointer form is changed on the OSD menu,
this setting is subsequently used.

CONTRAST

LAMP

IMAGE ROTATION

F.A.M.

POSI/NEGA COLOR/B&W

IRIS

NORMAL OPEN CLOSE

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

IMAGE

CALL

POWER

PAUSE

AF

SET

PRESET

CALLSET

IMAGE ROTATION

F.A.M.

TELE

ZOOM

MENU

WIDE

NEAR

FOCUS

FAR

Wireless remote control

Wireless remote control

11

28

1

2

3

4

5

6

7

8

9

10

Main Menu

Icon Name

Lamp

Posi/Nega
conversion

Color/B&W
selection

Image rotation

Function

Reference Pages

To turn ON/OFF the lighting.
When power is turned ON, the
previous saved setting remains.

To switch the selection of the
Color/B&W of the screen.
When power is turned ON, the
previous saved setting remains.

To switch the selection of the
positive/negative of the screen.
When power is turned ON, the
previous saved setting remains.

To rotate the image
counterclockwise by 90°.
When power is turned ON, the
previous saved setting remains.

P. 17

P. 19

P.20

P.20

P. 21

To switch the selection of the
static/moving image.
When power is turned ON,
the initial state is Animation.

To switch the modulation (edge
emphasis) of the image.
When power is turned ON, the
previous saved setting remains.

To change the color and shape of
the pointer on the screen. Every
time the left button of the mouse
is clicked, the icon pointer is
switched in order of “[

White arrow

→ Blue arrow → Yellow arrow →
Red arrow] → [White line → Blue
line → Yellow line → Red line]

”.

Pointer

Aperture
selection

Pause

11

29

1

2

3

4

5

6

7

8

9

10

Icon Name Function

Reference Pages

To save initial status when power
is turned ON.
For the mouse pointer ON/OFF
selection the same items stored in
the Preset/Move operation are
saved.

To reset this product to the
status of the factory settings.

To adjust the focus .

To focus automatically.

To adjust the zoom of the lens.

Status saving

Initialization

Auto Focus

Focus
Near/Far

Zoom
Tele/Wide

To adjust the iris of the lens.

Auto/Manual selection
cannot be changed by
the OSD.

Iris
Close/Open

P. 25

P. 24

P. 23

P. 17

P. 22

30

1

2

3

4

5

6

7

8

9

10

11

Icon Name Function

Reference Page

To set the White Blance in the
AUTO FOLLOW mode. (initial
setting)

To set the push-set White
Blance. When this button is
pressed the white balance for
the then color temperature is
fixed.

To set the white balance with
<RED>, <GREEN> and
<BLUE>. Adjust the white
balance by pressing the mouse
button on the direction buttons
beside the volume bar.
<RED>…To adjust the red
component (01-99).
<

GREEN

>…To adjust the green
component (01-99).
<BLUE>…To adjust the blue
component (01-99).

To display the White Balance
Adjustment menu. When this
button is pressed again, the
White Blance Adjustment menu
is closed.

White Balance

Auto

One-push

Manual

●● White Balance Adjustment

menu

●● Gamma menu

●● Power Supply Off

Timer

Sub Menu

31

1

2

3

4

5

6

7

8

9

10

11

Icon Name Function

Reference Page

Gamma
adjustment

To change the Gamma setting
value (00(1.0) / 01(0.9) /
02(0.8) / 03(0.7) / 04(0.6) /
05(0.5) / 06(0.4) / 07(0.3)).
The factory setting is “04
(0.6).” Gamma cannot be
adjusted when the CONTRAST
is ON in the negative status.

Power Supply
Off Timer

Sets the time between end of
operation and power OFF.
The time can be set within the
range from 01 (1h) to 08 (8h).
When 00 is set, the timer does
not operate.
If Power Supply is turned OFF,
the indicator LED turns orange.

32

1

2

3

4

5

6

7

8

9

10

11

8 RS-232C SPECIFICATIONS

This product can be controlled by a PC connected through the RS-232C terminal [RS-232C].

Setting Up

(1) Connect this product to a PC with an RS-232C connection cable.

When using an RS-232C cable available in the market, select a cable with the connection
shown below.

To protect this product and the PC, be sure to turn OFF all the power supply of all equipment
before connecting.

(2) Start the PC, and set the communication mode of the RS-232C to the communication

mode of this product.

For the information how to set the communication mode of the RS-232C, refer to the
instruction manual of the PC.

(3) Start the PC program to operate this product.

(4) Control through the RS-232C will start.

For communication control, be sure to take the above steps for setting.

Cable Connection

54321

9876

1
2
3
4
5
6
7
8
9

CD
RXD
TXD
DTR
SG
DSR
RTS
CTS
RI

CD

RXD

TXD
DTR

SG

DSR

RTS

CTS

RI (CI)

1
2
3
4
5
6
7
8
9

DSUB-9P (Female)

54321

9876

PC side :
DSUB-9P (Female)

Ceiling Presenter side

(DSUB-9P)

PC side
(DSUB-9P)

33

1

2

3

4

5

6

7

8

9

10

11

Data Format Specifications

This command is executed in the form of 1-command/1 packet. The next command is not
accepted until the previous processing is completed.

• The communication command always starts with STX (Start of Text) , and ends with ETX
(End of Text) .

• If the communication format or command name is wrong, NAK (Negative
Acknowledgement) will be sent from this product.

• When the communication format is correctly received, this product sends ACK (Normal
Acknowledgement).

■

Transmission command (PC → Ceiling Presenter)

Each operation command is executed in ASCII code, and transmitted in a set of 7 bytes as
follows:

S

T

X

E
T
X

Command

(PC)

(Ceiling

Presenter) → ACK

Data

Parameter

Connection

If the RS-232C cable is not correctly connected between this product and the PC, no
acknowledgement is transmitted. Connect the RS-232C cable correctly, and fix it firmly with
the connector set screws before the operation.

Transmission Specifications

• Full duplex start-stop sync. mode

• Start bit : 1 bit

• Data bit : 8 bits

• Stop bit : 1 bit

• Parity bit : None

• X parameter : None

• Baud rate (Communication speed) : 9600bps

34

1

2

3

4

5

6

7

8

9

10

11

■

Response data format (Ceiling Presenter→ PC)

All response data is transmitted as ASCII code, and it covers parameter of the table of
operation command table.

• Status 0

• Status 2

• Status 7

• Status 8

Byte not storing images is 30H.
Byte storing images is 31H.
Byte reading out images is 32H.

• ROM version

F.A.M.

Iris

mode

Power
supply
off time

AUTO:31H

MANUAL:32H

20H 20H 20H 20H

20H

S
T
X

E
T
X

Image

memory8

Image

memory7

Image

memory6

Image

memory5

Image

memory4

Image

memory3

Image

memory2

Image

memory1

S
T
X

E
T
X

V

56H

H

48H

K

4BH

S
T
X

E

T

X

20H

ROM version 1

ROM version 2

S

T

X

Posi /
Nega

Color

/ B&W

Pointer

display

Digital

Magnification

Local

lockout

E
T
X

30H

Lamp

on/off

Pause

γ

adjustment

32H

30H

S
T
X

Image

rotation

Aperture

White

Balance

Contrast

30H

(Normal)

31H

(Adjustment)

E
T
X

35

1

2

3

4

5

6

7

8

9

10

11

Function

Command

Parameter

Data

Auto Focus AF ■ ■0

Posi/Nega NP ■ ■0 (POSI)

1 (NEGA)

Color/B&W CB ■ ■0 (COLOR)

1 (B&W)

Pointer display PO ■ ■0 (OFF)

1 (ON)

Digital
Magnification

MA

■ ■

■ ■0 (OFF)

1 (ON)

Pause FZ 0 (OFF)

1 (ON)

Magnified
image move

PM ■ ■0 (STOP)

1 ( → )
2 ( ← )
3 ( ↑ )
4 ( ↓ )
5 ( )
6 ( )
7 ( )
8 ( )

•

When the pointer is ON: The pointer moves.

• When the image magnification is ON.:
The magnified image moves.

Focus
adjustment

FO ■ ■+ (NEAR)

– (FAR)
0 (STOP)

Zoom
adjustment

ZO ■ ■+ (TELE)

– (WIDE)
0 (STOP)

Lamp PL ■ ■0 (OFF)

1 (ON)

Iris adjustment IR ■ ■+ (OPEN)

– (CLOSE)
0 (STOP)
1 (AUTO)
2 (MANUAL)

Comments

↑

↑

↑

↑

■ ■γ adjustment GN 0 (γ = 1.0)
1 (γ = 0.9)
2 (γ = 0.8)
3 (γ = 0.7)
4 (γ = 0.6)
5 (γ = 0.5)
6 (γ = 0.4)
7 (γ = 0.3)

Image Rotation RO

0 (0°)
1 (90°)
2 (180°)
3 (270°)

■ ■

Aperture
selection

White Balance
selection

AP

AW

■ ■

■ ■

0 (OFF)
1 (ON)

0 (OFF)
1 (AUTO)
2 (

ONE-PUSH

)

UART Communication Format

Commands, parameters and data are all transmitted in ASCII code.

36

1

2

3

4

5

6

7

8

9

10

11

Function

Command

Parameter Data

F.A.M.
selection

CL

■ ■

0 (OFF)
1 (ON)

Comments

Image Store IS

■ ■

1
2
3
4
5
6
7
8

Image Read IC

■ ■

1
2
3
4
5
6
7
8

Contrast CT

■ ■

0 (OFF)
1 (ON)

Image Switch AV

■ ■

0

Local Lockout LL

■ ■

0 (OFF)
1 (ON)

Default DF

■ ■

0

Status request QS

■ ■

0
2
7
8

Rom version QR

■ ■

0

ACK check SA

■ ■

0 (OFF)
1 (ON)

CR addition SC

■ ■

0 (OFF)
1 (ON)

Power Supply DN

■ ■

0 (OFF)
1 (ON)

Power Supply
Off Timer

PW

■ ■

0 (OFF)
1 (1 hour)
2 (2 hours)
3 (3 hours)
4 (4 hours)
5 (5 hours)
6 (6 hours)
7 (7 hours)
8 (8 hours)

• To finish the IMAGE CALL mode and go
back to the normal camera image.

"■ ■" in the data column means that the SPACE [20H] should be transmitted twice.

37

1

2

3

4

5

6

7

8

9

10

11

• The lamp is very hot immediately after use. Direct contact

with the lamp or lamp cover will cause burns. Make sure that
lamp is thoroughly cooled off (30 minutes or more) before
replacing the lamp.

• Replacement of the lamp requires a work done at a high
location. Take care not to cause accident.

CAUTION

• Use JR12V50W AKM/5EZ-1 manufactured by Phillips for
replacement. Other lamps may blow out or cause fire if used.

WARNING

1. Turn OFF the Power Supply Switch.

2. Remove the power cord.

3. Wait until the lamp is thoroughly cooled off.

4. Remove the lamp cover.
Loosen the fixing screws and displace the lamp
cover in the arrow direction. (Fig. 1)
Turn the lamp cover around the fixing screw.
(Fig. 2)

5. Replace the lamp.
Rotate the lamp and install a new lamp.

6. Install the lamp cover.
Lamp cover shall be installed in sequence
reverseto its removal.

REQUEST

Since the lamp is made of glass, do not touch the glass surface with bare hands, apply a
strong impact, or scratch the surface.

screw

Replacing the Lamp

The lamp that is installed in the product has a certain life span. When the lamp is used for a
long period, the lamp light may become dark or the lamp may go off due to the end of its life.
(The life of the lamp varies according to the utilization condition.) In this case, replace the lamp.

How to replace the lamp

9 REPLACING THE LAMP

(Fig. 1)

(Fig. 2)

38

1

2

3

4

5

6

7

8

9

10

11

10 TROUBLESHOOTING HINTS

Check the following items. If any abnormality is found, consult the seller or our branch/office
in your area.

No image on TV
monitor.

• Cable is not properly connected to the video-in terminal of monitor.

• The power cord is disconnected from the wall AC outlet.

•

The plug is disconnected from the power cord receptacle of this product.

• The power switch is not turned ON.

• Zoom is set at TELE to display only white/black part of the

material.

• The power switch is turned ON immediately after it is turned OFF.
In this case, this product may not start. Wait several seconds after

turning OFF the power switch, and then turn ON the power switch.

Symptom Possible cause / countermeasure

Image is too dark.

The image is striped.

Brightness tone is out
of order.

Out of focus

Image oscillates.

Video output image
is disarrayed.

•The object is too close to the lens.
Check it the object is not placed at a distance shorter than 1.3m

(51.2 in.) from the unit.

• FOCUS is set at the extreme position of WIDE and the picture is
zoomed to TELE. FOCUS at the extreme position of TELE and zoom
the picture to WIDE.

• Focusing is sometimes difficult in the AUTO FOCUS mode.

• If image oscillates widely at TELE position or in the digital

magnification, vibration of the building could affect the event.

By pushing the [PAUSE] button on the wireless remote control,

image oscillation is alleviated by displaying still image.

• The intensity of illumination is not sufficient.

Turn ON the lamp by pressing the [LAMP] button on the wireless

remote control.

• If the distance from this product to a manuscript is long, illuminate
the surface of specimen brighter by using external lighting.

• Is the iris adjusted to "Close" side? Adjust the iris to "Open" side.

• This may be interference fringes between dots of printed matter

and TV scanning lines or CCD pixels, which may be mitigated by
changing the projection range.

• When using an LCD projector, vertical stripes may appear on the
screen. This may be mitigated by manually adjusting the dot clock
frequency on the projector side (refer to P. 15).

• This may be mitigated by switching the Gamma setting.

• Is the video output type set to PAL?

If this product which is set to PAL is connected to the monitor
specially designed for NTSC, the video image may not be output
normally, in which the image is disarrayed, or becomes black
and white.
Switch the video output type by referring to P. 9 "DIP Switches."

Symptoms and Confirmation

39

1

2

3

4

5

6

7

8

9

10

11

■ General

11SPECIFICATIONS

Item

Power source AC100 - 240V 50Hz/60Hz
Rated current 1.2 - 0.6A

Weight

6.5 kg (14.3 lbs.) (main body only)

Output terminal RGB output ×1

×1
×1

Composite Video output
S-Video output

Mini DSUB 15P connector, female

Ext. control
terminal

×1
×1
×1

RS-232C
Mouse

USB

DSUB 9P connector, male
Mini DIN 6P connector, female
Type B receptacle

RCA pin jack/75Ω unbalanced (NTSC/PAL)
Mini DIN 4P connector/75Ω unbalanced (NTSC/PAL)

Dimensions
(W × D × H)

226mm × 226mm × 239mm (8.9 × 8.9 × 9.4 in.)

Specifications

40

1

2

3

4

5

6

7

8

9

10

11

■ Camera

Item

Lens f = 14.2 – 170mm (12 - time zoom), F2.6 – 2.7
Frame rate

20 frames / sec

Limit of focus
adjustment

Distance from the unit to the text (object of shooting):

Zooming Electromotive (with double speed function)
Focusing Auto / Manual
Iris

Auto (level adjustable) Manual (RS-232C)

Image pick-up device

1/3″ CCD

Total pixels

1077(H) × 788(V), 850,000 pixels

Effective

pixels

1034(H) × 779(V)

Sync. system Internal sync.

Composite Video output

NTSC/PAL
S-Video output NTSC/PAL
White Balance

Posi/Nega conversion

Full auto / One-push / Manual

Provided
Color/B&W selection

Provided

Provided (0° / 90° / 180° / 270°)

Provided (1.0 / 0.9 / 0.8 / 0.7 / 0.6 / 0.5 / 0.4 / 0.3)

Provided

Provided (NTSC / PAL)

Provided

Provided

Provided (double, can be scrolled)

Controllable (color selectable)

Image Rotation

Provided

Contrast
Gamma selection
Aperture selection
Pause
Digital magnification

Pointer
F.A.M. selection

Resolution

Analog RGB
output

Analog RGB output : Horizontal 600TV lines or more;

Vertical 600TV lines or more

Video output : Horizontal 400 TV lines or more

0.7V (p-p) 75Ω unbalanced, synchronization signal, positive polarity

Signal frequency

XGA: Horizontal frequency 48.363 kHz;

Vertical frequency 60.004 Hz (1024 × 768 at 60 Hz);

Compliant with VESA

Shooting area(H × V)
(Projection -> photographing
distance: 2m(78.7in))

662mm × 511mm (26.0 × 20.1 in.) max.

53mm × 41mm (2.1 × 1.6 in.) min.

Specifications

Video output selection

Video output selection

Video output selection

■ Lighting

Item

Lamp Halogen lamp 12V 50W

(model: JR12V50W AKM/5EZ-1 manufactured by Phillips)

Specifications

41

1

2

3

4

5

6

7

8

9

10

11

■ Supplied Accessories

1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
3
4

QuantityName

Power cord (2.5m

)

Video cable (RCA pin connector) (3 m

)
S-Video cable (Mini DIN 4P connector) (2 m)
Infrared wireless remote controller (RCW-C1000

)
Batteries (Type R03, AAA)
Analog RGB cable (DSUB 15P connector) (2 m)
Analog RGB cable (BNC connector) (1.8 m)
Instruction manual
Installation manual
Warranty card
Scroll mouse
USB cable (1.8m)
Utility Software CD-ROM
Utility Software Installation Manual
C. Mounting fitting
Attaching screw (M4x10)
Attaching screw (M5x10)

■ Optional parts (to be purchased separately)

• Halogen lamp ( JR12V50W AKM/5EZ-1)

• Ceiling - mounting fitting VB-1000

For the RCA pin, use a pin plug compliant with RC-6703.

The above specifications are subject to change without notice.

Trademark Acknowledgements

VESA is a registered trademark of Video Electronics Standards Association.

VGA, SVGA, XGA and SXGA are trademarks or registered trademarks of International
Business Machines Corporation.

and , VISUAL PRESENTER, FOCUSFREE are trademarks of ELMO Co., Ltd.

[MEMO]

WARNING

Unauthorized recording of copyrighted

slide films, materials, photographs, etc.

may infringe on the rights of copyright

owners and be contrary to copyright

laws.

Printed in Japan

6X1VHK002

ELMO CO., LTD.

6-14, Meizen-cho, Mizuho-ku,
Nagoya, 467-8567, Japan

OVERSEAS SUBSIDIARY COMPANIES

U.S.A. ELMO Mfg. Corp.

1478 Old Country Road, Plainview, NY 11803-5034

Tel:[phone] Fax:[phone]

E-mail: [e-mail]

Web: http://www.elmousa.com/

Canada ELMO Canada Mfg. Corp.

44 West Drive, Brampton, Ontario L6T 3T6

Tel:[phone] Fax:[phone]

E-mail: [e-mail]

Web: http://www.elmocanada.com/

Germany ELMO (Europe) G.m.b.H.

Neanderstr. 18, 40233 Düsseldorf

Tel:[phone] Fax:[phone]

E-mail: [e-mail]

Web: http://www.elmo.de/

Printed on recycled paper