Elmo BOXI MP-350 Operation Manual

■ Read this guide and the separate “IMPORTANT SAFEGUARD” carefully before using the

projector.

■ This guide describes the configurations and operations using a wireless LAN (WiFi).

■ For the configurations and operations other than using a wireless LAN (WiFi), refer to the

separate “INSTRUCTION MANUAL - MASTER OPERATION GUIDE”.

■ Keep this guide in a safe place for future reference.

©2013 Copyright ELMO Co., Ltd. All rights reserved.

MP-350 (Ver.2)

INSTRUCTION MANUAL

Network Operation Guide

ENGLISH

2

IMPORTANT SAFEGUARDS

This section provides warnings about the wireless LAN (WiFi).
Also read the “IMPORTANT SAFEGUARDS” and “BEFORE YOU USE” in the
separate “INSTRUCTION MANUAL - MASTER OPERATION GUIDE”

NOTES ON THE USE OF WIRELESS LAN（WiFi）

■ This product uses 2.4GHz radio waves. The wireless device in this product has
been certified under the Radio Law.
Do not use this product under the following conditions:

-Near industrial, scientific, and medical devices, such as a pacemaker

-Near in-plant radio station for mobile equipment identifier (license required and
being used in factory line; etc.)

-Near low power wireless base station (license not required)

■ Depending on the using environment the wireless communication may be

adversely affected. Especially the wireless communication is not available when
there are reinforcing steel, metal and/or concrete between the product and the
equipment.

■ The frequency bandwidth permitted to be used varies depending on the radio wave
regulations in each country. Using this product outside the country may be illegal.

■ “Wireless LAN(WiFi)” is also referred to as “WiFi” in this guide.

N o t e

3

TABLE OF CONTENTS

IMPORTANT SAFEGUARDS..................................................................................... 2

NOTES ON THE USE OF WIRELESS LAN（WiFi） ................................................. 2

TABLE OF CONTENTS ............................................................................................. 3

1 BEFORE YOU USE ................................................................................................. 4

WiFi connection procedure ..................................................................................... 5

2 INSTALLING THE APPLICATION .......................................................................... 6

Installing BOXi Air ................................................................................................... 6

Installing BOXi Play ................................................................................................. 8

3 WiFi CONNECTION ................................................................................................ 9

SETTING UP THE PROJECTOR............................................................................ 9

Setting up Smartphones/tablets ............................................................................ 12

PC SETUP ............................................................................................................ 15

4 WIRELESS PROJECTION .................................................................................... 20

Using BOXi Air (Smart phones / Tablets)............................................................... 20

Use BOXi Play (PC:Windows/MacOS) .................................................................. 29

Display PC screen on 4 screens at the same time ................................................ 41

5 CHANGING IMAGE FROM WiFi DEVICE ............................................................ 43

Image controls from Web Browser ................................................................ ........ 43

6 BOXi NETWORK SETUP ................................................................................... 46

7 TROUBLESHOOTING .......................................................................................... 53

8 APPENDIX ............................................................................................................ 55

TRADEMARKS ..................................................................................................... 55

4

1 BEFORE YOU USE

This guide contains the instruction on connecting the projector to smartphones/tablets
(iOS/AndroidOS devices: hereinafter referred to as "mobile devices") or computers
(Windows/MacOS devices: hereinafter referred to as "Computer") using WiFi
(Wireless LAN) to project images from those devices wirelessly.

■ Benefit of the WiFi function
You can project Office documents (Word, Excel, PowerPoint) or PDF files using
the propriately application software "BOXi Air" (a client software) installed in
mobile devices.
You can also project a computer screen using another propriatery application
software "BOXi Play"(a client software) installed in computers.

■ Supported devices and versions:
BOXi Air (iPhone / iPad / iPod touch)

Supported OS versions:

iOS 3.2 or higher

Restrictions:

iOS4.2 or higher is required for PhotoViewer function
iOS5.0 or higher is required for slide show function

BOXi Air (android mobile/tablet)

Supported OS versions:

Android OS 2.2 or higher

Restrictions:

CPU: operation frequency 600MHz or higher
(Duo-core 1GHz or higher is recommended)

BOXi Play (Windows PC)

Supported OS versions:

Windows 8, 7, Vista, XP SP2/SP3 (32bit / 64bit)

Restrictions:

CPU: Dual Core 1.8 GHz or higher (except Atom)

1GB memory or higher

nVIDIA or ATI graphic card (VRAM 64MB or higher)

WiFi:IEEE 802.11n

BOXi Play (Mac)

Supported OS versions:

Mac OS X (10.5, 10.6, 10.7)

Restrictions:

CPU: Intel Dual Core 1.4 GHz or higher (except Power PC)

1GB memory or higher

nVIDIA or ATI graphic card (VRAM 64MB or higher)

WiFi: IEEE 802.11n

5

WiFi connection procedure

BOXi Air (for smartphone/tablets)

"2-1 Installing the iOS version" P.6
"2-2 Installing the Android version" P.6

"2-3 Uploading with the iOS version" P.6

"3-2 WiFi settings for iOS devices" P.12
"3-3 WiFi settings for Android devices" P.14

"4-1 Use BOXi Air for iOS." P.20
"4-2 Using BOXi Air for Android" P.24

BOXi Play (for personal computer)

"2-4 Installing BOXi Play (for both Windows
and Mac)” P.8

"3-4 Wi-Fi Setup on Windows" P.16
"3-5 WiFi Configuration for Mac OS.” P.17

"4-3 Use BOXi Play for Windows" P.29
"4-4 Use BOXi Play for MacOS" P.32

Install applications

Upload files to be projected

"3-1 WiFi settings - Setting up the projector" P.9

Connect devices to the projector using WiFi

Start projection using the application

Configure the WiFi settings of the projector

6

2 INSTALLING THE APPLICATION

Installing BOXi Air

The proprietary application software “BOXi Air” can be installed as
follows:

2-1 Installing the iOS version

Install BOXi Air from the App Store on your iOS device.

2-2 Installing the Android version

Install BOXi Air from Google Play on your Android device.

Follow these steps to register the files that you want to display with
BOXi. (iOS version only)

2-3 Uploading with the iOS version

1. Connecting to a PC that has iTunes

Use a proprietary cable to connect the iOS device for installation to a computer
(Windows PC or Mac) which has iTunes installed.

2. Starting iTunes
Follow the steps below after starting iTunes to go to the” Apps” screen.

A) From the left menu, click the name of the device (A) that you have connected

to your computer.

B) Click “Apps” in the top menu (B).

ELMO

ELMO

A)

B)

7

3. Click the icon “BOXi Air” on the Apps screen.

4. Select the file that you want to display.

Select the file that you want to display from the file selection window.

A) Click “Add” on the lower right.
B) Select the file that you want to display and click “Open”.

(Repeat this process to select multiple files.)

■ Also refer to the instruction manual for iOS device.

Click

ELMO ELMO

BOXi‗Air_How_To.pdf

N o t e

8

Installing BOXi Play

The proprietary BOXi Play software for PCs can be downloaded from the BOXi
website.

2-4 Installing BOXi Play (for both Windows and Mac)

Download BOXi Play to your computer from the BOXi website.
(http://boxi.elmoglobal.com)

1. Perform installation of BOXi Play after downloading.

A) Double click the BOXi Play installer.

B) Follow the instructions for installation.

C) The window closes and installation is complete.

Click “Next”

9

3 WiFi CONNECTION

SETTING UP THE PROJECTOR

3-1 WiFi settings - Setting up the projector

1. Press the button on the control panel or

on the remote control to turn on the projector.

2. Press the MENU button.

Perform the following operations after
the flashing wireless LAN indicator (blue) turns steady.

3. Select the “Input source select” icon .

Select the “Input source select” icon in the
“Main” menu with the buttons on the

control panel or on the remote control.
Then press the button to execute the
selection.

4. Select the “WiFi” icon .

Select the “WiFi” icon in the “Input source
select” menu with the buttons on the

control panel or on the remote control.
Then press the button to execute the
selection.

control panel Remote control

Main menu

Input source select menu

10

The “WiFi” menu will be displayed.

5. Select “Connect WiFi Device”.

"Connect WiFi Device" is already selected in
the disaplyed screen, so press the
button to execute the selection.

The “WiFi standby” screen will be displayed.

Leave the projector in this condition to connect
computers.

■ In the “WiFi standby” screen, the “LOGIN CODE**** (4-digit number)”
will be displayed at the left top of the screen.

This code will be automatically renewed every time the projector is
turned on. This code is for “BOXi Air”.

WiFi Menu

Connect

Wifi Device

N o t e

LOGIN CODE: XXXX

Server IP: 192.168.100.10

Resolution: 1200x800

Version: 2.0.0.7

SSID: BOXi-xxxxxxx

Channel: x

Security: OFF

WiFi standby screen

LOGIN CODE: XXXX

Server IP: 192.168.100.10

Resolution: 1200x800

Version: 2.0.0.7

SSID: BOXi-xxxxxxx

Channel: x

Security: OFF

11

■ Pressing the buttons on the control panel or on the remote control too
fast may freeze the screen. If the screen is frozen, try to press the
buttons slowly several times.

■ When changing the input source to “WiFi”, make sure that the wireless
LAN indicator is on.

N o t e

12

Setting up Smartphones/tablets

3-2 WiFi settings for iOS devices

Follow the instruction below when using iOS mounted smartphones/tablets.

1. Preparation

Turn on your iOS device.
Turn on the BOXi.

2. Open "Settongs" and set up WiFi.

To be continued to the next page.

Tap

Tap

Turn ON

BOXi-xxxxxxx

Tap

13

Connection between iOS device and the BOXi is completed.

BOXi-xxxxxxx

Tap

14

3-3 WiFi settings for Android devices

Refer to the following to set up on smart phones/tablets with Android.

1. Preparation

Power on the Android device.
Power on BOXi.

2. Open the Wi-Fi Settings application to perform setup.

Connection between BOXi and the Android device for setup is now complete.

Tap

Turn ON

BOXi-xxxxxxx

Tap

BOXi-xxxxxxx

15

PC SETUP

BOXi Play has software for Windows and Mac.

Refer to the setup procedures below.

■ Use a PC with Wi-Fi to use BOXi Play.

■ Activate Wi-Fi on the PC.

■ Also refer to the instruction manual for your PC, iOS or Android device.

■ If the Projector name (SSID) is changed in the “Network Setup” menu on

the projector, the changed Projector name (SSID will be displayed on
your device.
Refer to “6 BOXi NETWORK SETUP” (page 46) for details.

■ When using optional settings for IP address, subnet mask, routers or
DNS on the projector’s “Network Setup” menu, use the following network
configurations on your device:

- IP Address: different number from projector

- Subnet mask: same as subnet mask on the projector.
Refer to “6 BOXi NETWORK SETUP” (page 46) for details.

■ If you cannot connect the projector to your device after setting the IP
address and subnet mask, set the router for your device as follows.

- Router: same IP address as the projector

N o t e

N o t e

16

3-4 Wi-Fi Setup on Windows

1. Open “START” ”Control Panel”

2. Select “Network and Internet” “Network and Sharing Center”

When the window below opens click “Connect to network.”

3. Select / Connect SSID “BOXi-xxxxxxx”

The “Network Connections” window is displayed. WiFi networks which can be
connected to our listed. Select the BOXi SSID “BOXi-xxxxxxx” that you want to
connect to and click “Connect.”

4. Select auto configuration of IP address

Open “Networks and Sharing Center” from #2 above.
Click “Wireless Network Connection (BOXi-xxxxxxx).”

The “Wireless Network Connection Status” window is opened.
A) Click “Properties”.

The “Wireless Network Connection Properties” window is opened.
A) Select “Internet Protocol Ver.4”.
B) Click “Properties”.

The “Internet Protocol Ver. 4 (TCP/IPv4) Properties” window opens.
A) Select “Automatically obtain IP address.”
B) Select “Automatically obtain DNS server address”.
C) Click OK and the window will close.

■ The default SSID for the project is “xxxxxxx.”
Example) BOXi-2000000

N o t e

17

3-5 WiFi Configuration for Mac OS.

1. Open Apple MenuSystem Preference

2. Select “Network”

Click “Network” from the “Internet & Wireless” section.

18

3. Select “BOXi-xxxxxxx.”

Open the Network Screen.
A) Select “Wi-Fi”.
B) Select the BOXi SSID “BOXi-xxxxxxx” that you want to connect to from the
Network names.
C) Click “Advanced”.

N o t e

■ The Network Screen below is displayed.
Click “Turn Wi-Fi Off” before setting up the network.

BOXi and your computer may not be able to be connected if “Turn
AirPort Off” is not selected.

BOXi-XXXXXXX

19

4. Select “Use DHCP server”

3. Clicking “Advanced” opens the following screen.

A) Click “TCP/IP.”
B) For IPv4 select “Using DHCP.”
C) For “Configure IPv6” select “Automatically.”
D) Click OK.

A)

B)

C)

D)

BOXi-xxxxxxx

① ② ③

20

4 WIRELESS PROJECTION

Using BOXi Air (Smart phones / Tablets)

4-1 Use BOXi Air for iOS.

The WiFi Standby Screen on the left
appears on the projection screen to connect
to WiFi.

SETTING UP THE PROJECTOR (page 9)

1. Tap “BOXi Air” on your iOS device

The screen on the right is displayed.

xxxxxxx

Tap

Tap

WiFi Standby Screen

LOGIN CODE: XXXX

Server IP: 192.168.100.10

Resolution: 1200x800

Version: 2.0.0.7

SSID: BOXi-xxxxxxx

Channel: x

Security: OFF

21

2. Enter the Login Code

The document file list and viewer selection screen below is displayed.

A) Enter the login code shown on
the BOXi WiFi Standby Screen.

BTap the Login Button.

SAMPLE.pptx

…Tap this to show Office / PDF

files.
(This screen)

…Tap this to show jpg/bmp files.

Viewable Office files are listed.

…Word documents

…Excel documents

…PowerPoint documents

…PDF documents

22

3. How to Use the Document Viewer

On the previous screen tap the file you want to display to view the file’s contents
as below.

・How to use the screen

※Tap center of screen to show or hide the icons and list on the top and bottom of

the screen.

■ If the Projector name (SSID) is changed from the “Nettowork Setup”
menu on the projector, the changed Projector name (SSID will be
displayed on your device.

■ Refer to “Change Network Details” (p. 46) for details.

■ Logging in (WiFi connection) with a different iOS device while using

BOXi Air with an iOS device will stop the current projection and start
projecting the files from the new device logged in (WiFi connection).

…Cancel projection and go back to the

File Selection Screen.

…Stop projection.

Tap the screen while stopped to
restart projection.

Projection Screen controls available:
Slide left/right: move page
Pinch out: enlarge
Pinch in: reduce size
Tap: Switch to full screen display

Page List:
Show selected document pages.
Controls available:
Slide left/right: move display list
Tap: send selected page to projection screen

N o t e

23

4. How to Use the Photo Viewer

Select files for display on the screen below by tapping to select the photo
viewer on the viewer selection screen.
Graphic data (jpg/bmp) such as from a camera’s storage folder on an iOS device
can be displayed with the photo viewer.

<Image selection screen>

<Projection screen>

※Tap center of screen to show or hide the icons and list on the top and bottom of
the screen.

Thumbnails are shown for displayable
photos.

Slide left/right: move page
Pinch out: enlarge
Pinch in: reduce size
Tap: Switch to full screen display

Show list of photos that can be displayed.
Controls available:
Slide left/right: Move the displayed list
Tap: move photo to projection screen

…Stop projection and return to the

photo selection screen.

…Stop projection.

Restart by tapping the screen

…Rotate image 90°to the right.

…Start slideshow

24

4-2 Using BOXi Air for Android

The WiFi Standby Screen on the left
appears on the projection screen to connect
to WiFi.

SETTING UP THE PROJECTOR (page 9)

1. Tap “BOXi Air” on Android devices.

The screen below will appear.

Searching for BOXi Tap the displayed BOXi

WiFi Standby Screen

Tap

LOGIN CODE: XXXX

Server IP: 192.168.100.10

Resolution: 1200x800

Version: 2.0.0.7

SSID: BOXi-xxxxxxx

Channel: x

Security: OFF

25

2. Enter the Login Code

The viewer selection screen below is displayed.

① Enter login code shown on

WiFi Standby Screen on

②Tap “Connect”

…Tap to show Office documents/

PDF files.

…Tap to show jpg/bmp files.

ELMO

26

3. How to Use the Document Viewer

・How to select files

On the viewer selection screen tap and select the document viewer to select
the file for display on the screen below. (SD card data from the Android device can be
selected)

All folders with Office docs or
PDF files on the SD card are
shown.
Tap the folder containing the file
to be displayed.

All files in selected folder are
listed.
Tap file to be displayed. File
icons are shown below.

…for Word documents

…for Excel documents

…for PowerPoint

…for PDF documents

memo

etc

27

・How to Use the Screen

※Tap center of screen to show or hide the icons and list on the top and bottom of
the screen.

Controls on Projection Screen:
Slide left/right: move page
Pinch out: enlarge
Pinch in: reduce size
Tap: Switch to full screen display

Page list:
Show pages of selected document.
Controls available:
Slide right/left: Move display list.
Tap: Move selected page to projection

Cancel projection and return to file
selection screen

Pause projection. Tap screen to

restart projection.

28

4. How to Use the Photo Viewer

Tap on the viewer selection screen and select photo viewer to select files
displayed on the screen below.
The photo viewer can be used to show image data (jpg/bmp) such as from camera
data storage folders for an Android device.

Tap the folder to show the files
within the selected folder.

Cancel projection and return to photo
selection screen.

<Projection screen>

Stop projection

Projection Screen: controls available:
Slide right/left: Go to last/next photo
Pinch out: Enlarge display
Pinch in: Reduce display
Tap: Switch to full screen display on device

Photo List: Show photos from the folder
Available controls:
Slide left/right: Move the display list.
Tap: Move selected photo to projection

<Folder selection screen>

Tap

Picture

Tap

<Photo selection screen>

29

Use BOXi Play (PC:Windows/MacOS)

Let’s explain how to connect with Windows or Mac.

4-3 Use BOXi Play for Windows

1. Open BOXi Play

The first time BOXi Play is started, a performance test wizard for your computer
is activated. Follow the steps below to proceed.

Click “Next”

Select “Determined by

the Remoting Device.”

Click “Finish.”

■ Connection procedures the first time connecting BOXi Play differ
slightly the second time and after. Refer to p. 37 for procedures to
connect the second time and after.

N o t e

30

2. Select an Access Point

※The “Connect to Access Point” window is not displayed if the WiFi connection

is complete. Advance to “3. Enter Login Code.”

3. Enter Login Code

If the following message appears, click OK.

※For smooth operation, screen resolution is automatically changed while BOXi Play is

running. Resolution is restored automatically when BOXi Play is closed.

Select SSID

“BOXi-xxxxxxx.”
Click “Connect.”

IP address for the projector is
displayed.

Enter the login code.

****

Click “Connect.”

■ Refer to “SETTING UP THE PROJECTOR” (p. 9) for details on the login
code.

N o t e

BOXi-xxxxxxx

31

4. Menu panel is displayed on the desktop.

The menu panel appears, and the desktop screen is projected from BOXi.

5. Quit BOXi Play

BOXi Play closes when the Quit Button is clicked.

Menu Panel

■ The remote box appears during connection or while searching for a
network.

Quit Button

■ The message below appears if the PC screen is projecting. Click OK to
quit.

N o t e

N o t e

32

4-4 Use BOXi Play for MacOS

1. Open “BOXi Play"

The first time BOXi Play is started, a performance test wizard for
your computer is activated. Follow the steps below to proceed.

Click “Next.”

Select “Determined by the

Remoting Device”.
Click “Finish.”

■ A computer performance test wizard is launched the first time opening
BOXi Play on Mac.

After that, operations are the same for the first time as for the second time and
later.

N o t e

33

2. Enter IP address for the projector.

The Quick Connection screen below appears.

3. Enter the login code.

Click OK when the message below appears.

① Enter IP address for the

projector in the “Remote Box

IP” column.

② Click “Connect.”

■ Entering the login code on the Quick Connection screen is not necessary.

① Enter the Login Code.

② Click “Connect.”

■ Refer to “SETTING UP THE PROJECTOR” (p. 9) for details on the login
code.

N o t e

N o t e

① ② ①

②

Click

34

4. The menu panel is displayed

Connection is complete when the menu panel is shown on the desktop.

5. Quit BOXi Play

Click the Quit Button to close BOXi Play.

Menu Panel

■ Remote box is displayed during connection or while searching for a network.

Quit Button

■ The following message appears when the PC screen is being projected.
Click OK to quit.

N o t e

N o t e

35

※How to connect after first time (BOXi Play for Windows PC)

Checking and setting “SETTING UP THE PROJECTOR” (p. 9) is required when the
projector was connected to a different network after using it the last time.

1. Open “BOXi Play”

Follow the steps below when connecting from the second time.

2. Enter the login code

Click OK if the following message appears.

Click “Connect.”

****

IP address for the projector is
displayed.

Enter the login code.

Click “Connect.”

36

3. The menu panel is displayed

Connection is complete when the menu panel appears on the desktop.

(For BOXi Play for MacOS, the procedure is the same the first time as the second and
later times.

Menu Panel

37

※How to Control the Menu Panel

Use the menu panel while using wireless projecting to check controls and status.
The menu panel buttons represent the controls and projection status.

Naming of the Menu Panel Buttons

Pause button

Play/Stop button

Screen switch button

Minimize button

Menu button

Close button

Play 4 button

Play 2 button

Full screen display

Play 3 button

Play 1 button

38

Checking Projection Status

Button

Status

Projecting PC screen with the projector.

Not projecting PC screen with the projector.
PC screen projected is paused.

Button

Status

Projecting PC screen on upper left.

Projecting PC screen on upper right.

Projecting PC screen on lower left.

Projecting PC screen on lower right.

Projecting PC screen on full screen.

39

Menu Panel Controls

Action

Button

Operation

Project PC screen

PC screen is not projected when the
Play/Stop button on the menu panel is as
shown on the left.
Click the Play/Stop button or Full Screen
to project.

Stop projection of
PC screen

PC screen is projected when the
Play/Stop button on the menu panel is as
shown on the left.
To stop projection click the Play/Stop
button.

Pause PC screen

Click the Pause button.

Resume PC screen

Press the Pause button again.

Project PC screen
to upper left

Click the Play 1 button.

Project PC screen
to upper right

Click the Play 2 button.

Project PC screen
to lower left

Click the Play 3 button.

Project PC screen
to lower right

Click the Play 4 button.

Close BOXi Play

Click the Close button.

Show menu

Click Menu button
→See below for details on the menu.

Minimize menu
panel

Click the Minimize button

40

Menu Button

Click the Menu button to show the details menu below.

Num.

Menu Name

Details

①

Search Remote Box…

Select to search and connect another
BOXi that can be connected.

②

Projection Quality

Select either Normal or Best.

③

Auto Power Management

Disabled on this projector.

④

Auto WiFi Connect

Next connection will be automatic.

⑤

Advanced Screen Capture

Disabled on this projector.

⑥

About

Show version info for BOXi Play.

⑦

Exit

Close this menu.

Menu Button

① ② ③ ④ ⑤ ⑥ ⑦

■ Actions may be lagging when the message below is shown on the screen
while controlling BOXi Play.

Perform operations after the message has disappeared.

Search Remote Box…

Projection Quality

Auto Power Management
Auto WiFi Connect
Advanced Screen Capture

About
Exit

N o t e

41

Display PC screen on 4 screens at the same time

Use BOXi Play to show up to four PC screens at the same time on one BOXi.

*figure

1. Project WiFi standby screen and open “BOXi Play.”

2. Enter the same login code on the PCs to be connected at the same.
time.

Enter the login code shown on the WiFi
standby screen to login all PCs to be
simultaneously connected (up to 4).

The PC screen in which the Login
button was pressed first will be
projected first.

LOGIN CODE: XXXX

Server IP: 192.168.100.10

Resolution: 1200x800

Version: 2.0.0.7

SSID: BOXi-xxxxxxx

Channel: x

Security: OFF

42

3. Select a screen button

Select and click a screen button for the position you want to project to from the
PC.

Project the PC screens to the position specified in order from the button
clicked.

To project one PC screen to the full screen, use the Full Screen button.

①

②

④

③

Play 4 button

Play 2 button

Full screen button

<Screen button>

Play 3 button

Play 1 button

43

5 CHANGING IMAGE FROM WiFi DEVICE

Image controls from Web Browser

The control console for changing devices to be used for projection can be opened with
BOXi through a web browser (Internet Explorer/Chrome/Safari, etc.) from a PC
(Windows/Mac) or smart phone/tablet (iOS/Android) connected to the network.
(Refer to”3 WiFi CONNECTION” P9; Limited to one device at a time for one BOXi)

1. Open the BOXi Control Screen from the web browser

Open URL http://192.168.100.10/ (BOXi’s IP address) from the web browser.

① Click “Conference Control” from the above screen.

① Enter “trainer” for the password.
② Click “Login.”

①

②

①

44

2. Specify image and display position from the control screen.

On the following screen select images from the device connected to BOXi.

【Image Selection with BOXi Play】
Images can be sent to BOXi by using BOXi Play from a PC (Windows/MacOS device)
Choose from “Hide”, “Full Screen” or “4 panel display” on the control panel.

#

Icon

Description of Settings
①

Display projection in full screen

②

Display projection screen in top left quarter

③

Display projection screen in top right quarter

④

Display projection screen in bottom left quarter

⑤

Display projection screen in bottom right quarter

⑥

Do not display

Win-1

iPhone-1

Mac-1

Image from BOXi Play

↑① ↑② ↑③ ↑④ ↑⑤ ↑
⑥

Image from BOXi Air

Restrict projection screen controls to this screen

45

【Image selection from BOXi Air】
Use BOXi Air to send images to BOXi from your smart phone/tablet (Android/iOS
device)
On the control panel specify “Hide” or “Full Screen.”

#

Icon

Description of Settings

①

Display projection screen in full screen

②

Do not display

※If this screen is used but an image for projection is not selected, BOXi will project
the last requested image.

↑① ↑
②

46

6 BOXi NETWORK SETUP

Launch web browser (Internet Explorer/Google Chrome/Safari, etc.) from the
terminal on the device for setup.
(Refer to “3 WiFi CONNECTION” P9; IE is used below as an example)

6-1 Change Network Details

Open URL http://192.168.100.10 in the browser and click System Administrator.

Login as Admin (Default password is “admin.”)

Click

Click

Enter

“admin”

The screen below is shown when http://192.168.100.10
is entered here and the Return key is pressed.

47

Choose Network Setup from the list on the left side of the screen.

Change the necessary items on the screen below.

①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪

⑫
⑬
⑭
⑮
⑯

Click the Apply button
after updating
everything.
⇒Changes are
enabled automatically

after rebooting.

Click

48

Details of Settings

6-2 When changing the password

Choose “Change Passwords” from the list on the left of the screen.

Item

Default

Situations of change

IP Setup

①IP Address

192.168.100.10

To change the BOXi address

②Subnet Mask

255.255.255.0

To change the network address

③Default Gateway

192.168.100.10

To set up gateway server in the LAN

④DNS Server

192.168.100.10

To set up DNS server in the LAN

DHCP Setup

① “Auto”/”Disable”

Auto

When DHCP functions are not used

⑥Start IP

192.168.100.11

When changing DHCP-issued address

⑦End IP

192.168.100.254

When changing the DHCP-issued address.

⑧Subnet Mask

255.255.255.0

Make the basically same as ②

⑨Default Gateway

192.168.100.10

Make the basically same as ③

⑩DNS Server

192.168.100.10

Make the basically same as ④

Wireless Setup

⑪Wireless LAN

BOXi-xxxxxxx

Do not overlap with another device when
making changes

⑫SSID Broadcast

Enable

When using stealth setup (Improvement of
security)

⑬Channel

Auto

Locking the channel used for wireless LAN
(Only channels 1-11 can be used.)

⑭Encryption

Disable

To increase security
(Can select WEP/WPA/WPA2)

⑮Keys

(None)

When selecting encryption

⑯Hide Characters

Check

To check the text upon entry.

Click

49

Passwords for System Admin and Conference Control can be changed on the screen
below. Press “Apply” after inputting the new password.

6-3 Changing how to issue authentication code when connecting BOXi-Air and

BOXi-Play

Select Device Setup on screen below.

50

Method for issuing authentication code when connecting to the projector can be
changed with the WiFi connection tool from the screen below.

Meaning of Settings

Default

Meaning

Disable

Code unnecessary when connecting

Random

○

System generates four random digits when connecting

Specify

Specify code for connection
Code for connection can be specified (4 digits)

6-4 Restore Defaults
Select “Reset to Default” below.

Click the Apply
button after
setting

51

Click “Apply” on the confirmation window below.

Click OK when the message below appears.

SSID is not changed under factory default settings on the webpage.

To include SSID with factory default settings use “Restore factory

default settings” on the device. Also use “Restore factory default

settings” when network settings have been set incorrectly, and

network connection with the device is not possible.

N o t e

52

6-5 Rebooting

Select “Reboot system” on the screen below.

Click “Reboot” on the confirmation window below.

Click OK when the message below appears.

53

7 TROUBLESHOOTING

This section describes troubleshooting related to the wireless LAN (WiFi).
Also refer to the separate “INSTRUCTION MANUAL - MASTER OPERATION
GUIDE”.

The problems described in the following table may not be caused by malfunction of
the projector. Check the following table before asking for repair.
If the problem still remains after the troubleshooting, please contact your dealer for a
check.

Problem

Check These Items

Related

Page

Cannot establish
WiFi connection.

➡

There is an obstacle between the projector
and iPad or iPhone or the distance between
the projector and iPad or iPhone is too far.
【Remedy】Remove the obstacle or reduce
the distance between the projector and iPad
or iPhone.

→P2
➡

There are other devices in the
neighborhood that are using the same
frequency as that of the projector.
【Remedy】Keep those devices away from
the projector.

→P2
➡

The network information such as the IP
address has been changed.
【Remedy】Check the IP address of the
projector and iPad or iPhone.

→P エラー!
ブックマーク
が 定 義 さ れ
て い ま せ
ん。

54

WiFi connection is
sometimes cut off.

➡

There is an obstacle between the projector
and iPad or iPhone or the distance between
the projector and iPad or iPhone is too far.
【Remedy】Remove the obstacle or reduce
the distance between the projector and iPad
or iPhone.

→P2

Problem

Check These Items

Related

Page

WiFi connection is
sometimes cut off.

➡

There are other devices in the
neighborhood that are using the same
frequency as that of the projector.
【Remedy】Keep those devices away from
the projector.

→P2
➡

There is other device in the neighborhood
that is using the same IP address as that of
the projector.
【Remedy】Change the IP address.

→P エラー!
ブックマーク
が 定 義 さ れ
て い ま せ
ん。

No image is
projected.

➡

The projector is not in the “WiFi standby”

mode.

【Remedy】Call the “WiFi standby” screen.

→P9

➡ The projector is in the “Blank screen” mode.

【Remedy】Press the button on the
remote control.

“INSTRUCTION

MANUAL ­MASTER
OPERATION

GUIDE”

→P39

55

8 APPENDIX

TRADEMARKS

The following trademarks /registered trademarks are used in this guide.

 Is a registered trademark of ELMO Co., Ltd.
 DLP(Digital Light Processing) is a trademark of Texas Instruments.
 Mac, Mac OS, MacBook, MacBook Air, iPhone, iPad, ipod touch and iTunes are

trademarks of Apple Inc.

 App Store is a service mark of Apple Inc.
 iOS is a trademark or registered trademark of Cisco Systems Inc., registered in the U.S.

and other countries.

 Microsoft, Windows, Windows XP, Windows Vista, Windows 7, Windows 8, Word,

Excel and PowerPoint are trademarks or registered trademarks of Microsoft
Corporation, registered in the U.S. and other countries.

 Android and Google Play are trademarks or registered of Google Inc.
 Adobe PDF is a trademark or registered trademark of Adobe Systems

Incorporated, registered in the U.S. and other countries.

 Other company and product names mentioned in this guide are trademarks or

registered trademarks of their respective companies.

56

6-14, Meizen-cho, Mizuho-ku

Nagoya, 467-8567, Japan

ELMO USA CORP.

ELMO Europe SAS

Headquarters

Headquarters

1478 Old Country Road

Immeuble Elysées La Défense,

Plainview, NY 11803, U.S.A.

7C, Place du Dôme,

Tel. [phone] Fax.[phone]

92056 Paris La Défense, France

E-mail: [e-mail]

Tel. [phone]

Web: http://www.elmousa.com

Fax. [phone]

West Coast Branch

German Branch

5676 Corporate Avenue

Hansaallee 201, Haus 1

Cypress, CA 90630, U.S.A.

40549 Düsseldorf Germany

Tel. [phone] Fax. [phone]

Tel. [phone]

Fax. [phone]

6X1SPJBC2(en) R01-XeX

OVERSEAS SUBSIDISRY COMPANIES