Elkay HTHB-HRFER User Manual

HydroBoost® In-Wall Bottle Filler

Satisfying Thirsts Since 1912

MODEL: HTHB-HRFER

GENERAL

In-wall, recessed bottle lling station paired with the single Contour™
refrigerated fountain.

HYDROBOOST® BOTTLE FILLING STATION

In-wall, recessed design with solid lower panel. Quick ll rate is 1.1 gallons
per minute. Includes laminar ow to provide a clean ll with minimal splash
and easy maintenance. Equipped with automatic 20-second shut-off timer.
User interface design makes touchless operation intuitive. Key plastic
components are integrated with silver ion anti-microbial protection to inhibit
growth of mold and mildew.

Designed with hinged top and bottom stainless steel panels for easy
access and service.

GREEN COUNTER™

Visually displays count of plastic bottles saved from waste. (Based on

20 oz. bottles.)

FOUNTAIN

Features contoured basin and softly rounded corners and edges.

HALSEY TAYLOR DOUBLE BUBBLER™

Exclusive one-piece, chrome-plated two-stream mound-building bubbler
with non-removable anti-squirt feature and integral hood insures a
satisfying drink of water.

AUTOMATIC STREAM HEIGHT REGULATOR

Self-closing assembly is located inside unit to prevent tampering. Unit
resists corrosion and liming. A constant stream height is automatically
maintained under line pressures that vary from 20 to 105 psi.

PUSHBUTTON ACTUATION

Self-closing, vandal-resistant pushbutton does not require grasping or
twisting.

MOUNTING FRAME

Manufactured from corrosion resistant, galvanized steel. Open construction
designed for ease of installation. Mounting frames can be shipped in
advance for rough-in installation.

with Filtered Model HTHB-HRFER

HRF Fountain

With Bottle Filler

Rated for Indoor Use Only

Stainless Steel Finish Only

SUGGESTED SPECIFICATIONS

Model HTHB-HRFER provides 8.0 gph of 50°F water at 90°F ambient and
80°F inlet water. Bottle ller shall be recessed design and include electronic
sensor activation with 20-second automatic water shut-off. Shall provide

1.1 gpm ow rate with laminar ow to prevent splashing. Shall include
anti-microbial protected plastic components to prevent mold and mildew.
Shall include visual display of plastic bottles saved from waste. Fountain
shall have rounded corners and contoured basin, designed with easy
to operate pushbutton. Shall include SJ8 water chiller. Shall meet ADA
guidelines for visual and motion disabilities, when properly installed. Shall be
lead-free design which meets the Safe Drinking Water Act and is certied to
NSF/ANSI 61 and 372, UL 399 and CAN/CSA 22.2 No. 120.

Each HTHBWF-HRFER is shipped in 5 cartons including:

HYDROBOOST Station with Solid Lower Panel

HRF-ER Fountain

Mounting Frame (2)

Cooling Unit – SJ8

CAPACITIES CHART

Model

HTHB-HRFER 115V / 60Hz 8 GPH 4.0 260 123 lbs.

Note: Continued product improvement makes specication subject to change without
notice. See Halsey Taylor website for most current spec Sheet.

Voltage /

Hertz

Chilling**

Capacity

HALSEY TAYLOR, 2222 Camden Court, Oak Brook, IL 60523

F.L.

Amps

halseytaylor.com

Rated
Watts

Approx.

Ship

Wt.

UL399 and

CAN/CSA 22.2

No. 120

Certied

ADA

COMPLIANT

• • •

NSF/ANSI

61 and 372

Certied

SPEC00315 06/2015

Model HTHB-HRFER
HydroBoost® In-Wall Bottle Filler

Refer to diagrams for rough-in of plumbing and
electrical sources. The support frame is to be
installed rst. Hang upper Bottle Filler panel to
hanger on frame. Water service lines, waste
lines and electrical are assembled as required.
The bottom panel is attached last, after a nal
check for leaks and correct functions of Bottle
Filler. (For details see the installation instructions. )

INSTALL (2) SCREWS
(P/N 111008343890) IN FRAME
BEFORE INSTALLING IN OPENING

MOUNTING INSTRUCTIONS:

FRAME

5/16" SCREWS OR BOLTS
(10 REQ'D-NOT PROVIDED)

40"

1016mm

4 1/2"

114mm

NOTE: A service stop (not included) must be installed at
the fountain inlet line.
NOTE: P-Trap (not supplied) to be installed per local
building code.
NOTE: For wall support required locations see installation
instructions provided with panel and fountains.

CAUTION - Bottle Filler must be securely bolted to wall.

IMPORTANT:
DOUBLE STUD OR 3 INCHES (76 mm)
BETWEEN MOUNTING FRAMES
IF PLACED NEXT TO ANOTHER
BOTTLE FILLER, FOUNTAIN OR WALL

WOOD OR STEEL FRAME SHOWN
(NOT PROVIDED)

18 3/4"
476mm

FLOOR LINE

BACK OF WALL TO

8” (203mm)

BE 12" (305mm)

MIN DEPTH

MIN DEPTH

Satisfying Thirsts Since 1912

DOUBLE STUD OR 3" (76mm)
BETWEEN MOUNTING FRAMES
IF PLACED NEXT TO ANOTHER
FOUNTAIN OR WALL

Rated for Indoor Use Only

OPERATING PRESSURES:

Supply water - 105 psi maximum

Minimum 40 psi supply line pressure required in special
circumstances where both Bubbler and Hydroboost are
in use simultaneously to ensure adequate stream height.

ELECTRICAL

Hydroboost® station equipped with electric cord

and three-prong molded rubber plug for use with
15-amp minimum receptacle. For the cooling unit,
a junction box for a (3) wire, 10 amp branch circuit
is provided. Rated at 115 volt, 60 Hz, single phase.

TOP & SIDE VIEWS

9 3/8"
238mm

18 3/4"
476mm

ACTIVATION
SENSOR

®

FRONT VIEW

19 3/4"

1 3/16"
30mm

38 7/8"
988mm

32 11/16
831mm

502mm

17 3/8"
441mm

FINISHED FLOOR

Job Name: ______________________________

Date: __________________ Qty. ____________

Contact Info (Name, Phone, Email): __________

________________________________________

________________________________________

Approval: _______________________________

1 3/16"
30mm

20 3/8"
518mm

20 7/16"
519mm

27"
682mm

WALL LAYOUT

2 7/8"
73mm

25 1/4"
642mm

FINISHED FLOOR

8"

203mm
MINIMUM
DEPTH

4"
102mm

8" (203mm) MINIMUM
FOR DRAIN ACCESS TO
BOTTLE FILLER ELECTRICALS

BACK WALL LINE

1-1/4" (32MM)
WASTE TUBE

FURNISHED

25 7/8"
658mm

Page 2

Printed in the U.S.A.

Model HTHB-HRFER
Filtered Contour™ Fountain

WALL OPENING

IMPORTANT: It is necessary to create a wall opening 18 3/4” W
x 37 3/4” H and 4 1/2” above the oor line.

MOUNTING INSTRUCTIONS

Refer to rough-in for location of plumbing and electrical sources.
The support frame is to be installed rst. The shelf for the water
chiller should be assembled to the wall frame, and then place
chiller into position. Hang upper fountain panel to hanger on
frame. Fountains are to be attached to panel and wall frame.
Water service lines, waste lines and electrical are assembled as
required. The bottom panel is attached last, after a nal check
for leaks and correct functions of fountains and chiller.
(For details see the installation instructions.)

Installation required trap to be install in wall. Trap and
service stop not included.

OPERATING PRESSURES:

Supply water - 105 psi maximum

5/16" SCREWS OR BOLTS
(10 REQ'D-NOT PROVIDED)

HOOK RODS (2)
P/N 101567443730

CREWS OR BOLTS

S
(NOT PROVIDED)

FRAME

37 3/4"
959mm

4 1/2

114mm

I

MPORTANT:
DOUBLE STUD OR 3 INCHES (76mm)
BETWEEN MOUNTING FRAMES
IF PLACED NEXT TO A BOTTLE
FILLER UNIT

1"
25mm

WOOD OR STEEL FRAME SHOWN
(NOT PROVIDED)

ELECTRICAL INLET
LOCATION ON CHILLER

8"

203mm

TO FLOOR LINE

Satisfying Thirsts Since 1912

ELECTRICAL DATA

Junction box for a (3) wire 10 AMP branch
circuit. Standard 120 volt, 60 Hz, single phase.

TOP & SIDE VIEWS

3 1/8"

1 1/8"
29mm

B

79mm

A

5 5/8"
143mm

Rated for Indoor Use Only

INSTALL (2) SCREWS
(P/N 111008343890) IN FRAME
BEFORE INSTALLING IN OPENING

CHILLER SHELF
P/N 27638C

FRONT VIEW

19 3/4"
502mm

12 1/8"
308mm

18 3/4"
476mm

130mm

FLOOR LINE

20 3/8"
518mm

20 7/16"

519mm

5 1/8"

BACK OF WALL TO

BE 12" (305mm)

MIN DEPTH

33 1/2"
851mm

ADA
REQUIREMENT

WALL LINE

WALL LAYOUT

27"
686mm

18"
457mm

9 3/8"
238mm

12"
305mm

MINIMUM DEPTH

5/8"
16mm

BACK WALL LINE

C

31 1/4"
794mm

D

LEGEND:

A = 1/4” O.D. TUBE CONNECT (CHILLER WATER OUTLET)
B = 3/8” O.D. TUBE CONNECT (CHILLER WATER INLET) SHUT OFF VALVE BY OTHERS
C = 1-1/2” WASTE TUBE (ELBOW & TRAP NOT PROVIDED)

D = ELECTRICAL INLET

Page 3

FINISHED FLOOR

1"
25mm

11"
279mm

4 1/2"
114mm

8"
203mm

Printed in the U.S.A.