Elkay ELG250RSD0, ELGLBO3322WH0, ELGOU3321LPC0, ELGR13322GR0, ELGULB3322GR0 Installation manual
...
TO BE REMOVED FOR USE BY THE OCCUPANT!
Installation Instructions
E-Granite
™
Sink
• READ THESE INSTRUCTIONS THOROUGHLY BEFORE YOU BEGIN.
• Follow all local plumbing and building codes.
• Before installation, please inspect the sink for damage. Do not install a damaged sink.
• For undermount sinks proceed to section I. For drop-in sinks proceed to section II.
I. UNDERMOUNT INSTALLATION
ATTENTION INSTALLER:
•ELKAY RECOMMENDS THAT UNDERMOUNT SINKS SHOULD BE INSTALLED BY A PROFESSIONAL EXPERIENCED
INSTALLER.
• WARNING: THE ENCLOSED CUTOUT TEMPLATE PROVIDES A SINK OPENING THAT WILL EXPOSE APPROXIMATELY
1/8" OF SINK RIM LEDGE AS SHOWN IN ILLUSTRATION A.
• IT IS RECOMMENDED THAT YOU DISCUSS THIS WITH YOUR CUSTOMER AND AGREE TO WHAT THE FINISHED
EFFECT WILL BE. ELKAY IS NOT RESPONSIBLE FOR IMPROPER SINK OR COUNTERTOP INSTALLATIONS.
• ELKAY E-GRANITE UNDERMOUNT SINKS MUST BE FASTENED TO SOLID SURFACE COUNTERTOPS ONLY (I.E. GRANITE).
• ELKAY IS NOT RESPONSIBLE FOR SINK AND COUNTERTOP IF DAMAGED DURING INSTALLATION.
• FOLLOW ALL LOCAL PLUMBING AND BUILDING CODES.
1. Position template on countertop. Locate front to rear, so sink will not interfere with the cabinet.
2. Trace a line around the template. Cut along the inside of this line to provide opening.
3. Locate and provide for the mounting holes (following the countertop manufacturer’s instructions). Holes should allow for even
spacing around sink. Type of fasteners to be as recommended by countertop supplier.
4. Fasten mounting brackets to countertop loosely
5.
U
sing a high quality silicone adhesive caulk, apply a bead evenly all around the top of the sink flanges. CAUTION: DO NOT USE
EPOXY TO SEAL SINK.
6. Position and align the sink in the countertop opening.
7. Tighten fasteners until mounting brackets are snug against sink. (See illustration A).
C
heck alignment of sink to countertop opening.
8.
9. Tighten down fasteners evenly. Be careful not to over-tighten. Remove excess caulk and allow caulk to cure following the
caulk manufacturer’s instructions.
ILLUSTRATION A
II. DROP-IN INSTALLATION
Note: The clips provided are designed for a maximum countertop
thickness of 1-3/4”.
1. To determine the proper size opening for your sink place the sink
upside down on top of the countertop. Mark or trace line around the
edge of the rim. Then cut an opening 5/16” inside the line. (See
illustration B).
2. Set new sink in opening to see that it fits properly.
Elkay
2222 Camden Court
Oak Brook, IL 60523
©2016 Elkay
Printed in Germany
elkay.com
TRACE COMPLETELY
AROUND EDGE OF SINK
ILLUSTRATION B
DRAW SECOND
LINE INSIDE SINK
OUTLINE (CUT LINE)
5/16"
(Rev. 03/16) 0000000217
Installation Instructions
INK
II. DROP-IN INSTALLATION Cont.
Note: MUST SUPPORT FAUCET DECK ON BOTH SIDES WHILE
PUNCHING FAUCET HOLES.
3. Faucet Holes: Faucet holes can be identified by the faucet hole
emboss on the underside of the faucet deck and the corresponding
circular labels located on the faucet deck top surface. Before
punching the holes please verify that the circular labels are properly
centered over the faucet emboss. The faucet hole should be
carefully penetrated FROM ABOVE THE SINK using chisel or screw
driver and tapping lightly on the circular labels. (See illustration C).
If necessary the hole can been enlarged using a metal hole saw, a
jigsaw with a metal cutting blade
or a metal file.
4. Attach faucet, drain fittings and accessories according to the
manufacturer’s instructions.
5. Determine if your sink was shipped with the ORANGE DOWEL CLIP or the BLACK / GRAY SLOTTED SCREW CLIP. If
ORANGE DOWEL CLIP, go to step 7. If BLACK / GRAY SLOTTED SCREW CLIP, proceed to step 6.
6. As shown in illustration D and E, align clips with the corresponding slots in the sinks per illustration D. It may be necessary to
use a mallet and wood block to push it into place, as shown in illustration E. Make sure metal portion of the clip (clamp) is in the
open position so that sink can be dropped into cutout. Proceed to step 8.
ILLUSTRATION C
SILICONE CAULK
(NOT INCLUDED)
CLOSED
CLAMP
ILLUSTRATION D ILLUSTRATION E
ILLUSTRATION F
7. As shown in illustration G and H, align clips with the corresponding holes in the sink and gently push into place. Push plastic pins
on the clips inward completely so that the clip expands and engages the sink. Note that it may be necessary to use a pin punch or
screw driver and hammer to push pin in completely. Make sure metal portion of the clip (clamp) is in the open position so that the
sink can be dropped into cutout.
CLAMP
CLIP BASE
PLASTIC
PINS
ILLUSTRATION G
S
ILLUSTRATION H
8. Apply a bead of a high quality silicone adhesive caulk to the underside of the sink rim and position sink into countertop opening.
CAUTION: DO NOT USE EPOXY TO SEAL SINK.
9. Swing metal portion of clip (clamp) into the clip base. (See illustration F). Using a Phillips screw driver, turn screw until
clamp engages the countertop. Use shims if necessary.
10. Remove excess caulk and allow caulk to cure following the caulk manufacturer’s instructions.
Elkay
2222 Camden Court
Oak Brook, IL 60523
©2016 Elkay
Printed in Germany
elkay.com
(Rev. 03/16) 0000000217
Loading...