Page 1
EDFPVR320RC FTN
Elkay Owners Manual
Model: EDFPVR320RC Fountain
Marblyte Fountain
Installer
T o assure you install this model easily and correctly ,
PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE ST ARTING THE
INST ALLATION. CHECK YOUR INST ALLA TION FOR COMPLIANCE WITH
PLUMBING , ELECTRICAL AND OTHER APPLICABLE CODES. After installation, leave
these instructions inside the fountain for future reference.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WA TER LINES IS A COMMON PROCEDURE. THIS GROUNDING MA Y BE IN THE BUILDING OR MA Y
OCCUR A WA Y FROM THE BUILDING . THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNT AIN, CREA TING AN ELECTROL YSIS WHICH CAUSES A MET ALLIC T ASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS A VOIDABLE BY USING
THE PROPER MA TERIALS AS INDICA TED. ANY DRAIN FITTINGS PROVIDED BY THE INST ALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALL Y ISOLA TE THE FOUNT AIN FROM THE BUILDING
PLUMBING SYSTEM.
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPL Y
NOTE: WA TER FLOW
DIRECTION
BUILDING WAT ER
INLET
SERVICE STOP
(NOT FURNISHED)
FIG. 2FIG. 1
98456C (Rev. B - 12/08)
Page 2
EDFPVR320RC FTN
FIG. 3
DETAIL #1
SEE DETAIL #1
27"
686mm
CHILD
ADA
WASHER REQUIRED TO
MINIMIZE BREAKAGE
OF FOUNTAIN
(TYP.) ALL MOUNTING BOLTS
WASHERS NOT INCLUDED
5/8" MOUNTING HOLES
& SLOTS
4"
102mm
33 3/4"
857mm
28"
711mm
4 1/2"
114mm
27 3/8"
695mm
14 1/8"
359mm
L
58 1/2"
1486mm
27 3/8"
C
14 1/8"
359mm
695mm
4 1/2"
114mm
A
8"
203mm
FINISHED FLOOR
B
29"
737mm
29 1/2"
749mm
INTERNAL TRAP
98456C (Rev. B - 12/08)
PAGE 2
31 1/4"
794mm
LEGEND
A = 3/8" O.D. UNPLA TED COPPER TUBE CONNECT - SHUT OFF V AL VE BY OTHERS
B = WATER OUTLET 1-1/2" O.D. DRAIN - STUB OUT FROM WALL 1" (25mm)
Page 3
EDFPVR320RC FTN
FIG. 4
DETAIL #1
SEE DETAIL #1
27"
686mm
CHILD
ADA
WASHER REQUIRED TO
MINIMIZE BREAKAGE
OF FOUNTAI N
(TYP.) ALL MOUNTING BOLTS
WASHERS NOT INCLUDED
5/8" MOUNTING HOLES
& SLOTS
4"
102mm
33 3/4"
857mm
28"
711mm
4 1/2"
114mm
27 3/8"
695mm
14 1/8"
359mm
L
14 1/8"
695mm
4 1/2"
C
359mm
114mm
58 1/2"
1486mm
27 3/8"
A
8"
203mm
FINISHED FLOOR
B
26"
660mm
29"
737mm
EXTERNAL TRAP
PAGE 3
29 1/2"
749mm
LEGEND
A = 3/8" O.D. UNPLA TED COPPER TUBE CONNECT - SHUT OFF V AL VE BY OTHERS
B = WATER OUTLET 1-1/2" O.D. DRAIN - STUB OUT FROM WALL 1" (25mm)
98456C (Rev. B - 12/08)
Page 4
EDFPVR320RC FTN
INSTALLATION INSTRUCTIONS
1. Wall should already be framed for the fountain using the positioning dimensions shown in Figure 3 or 4.
Shown dimensions pertain to installation location (framing must support up to 150 lbs. weight).
2. Install rough-in plumbing as shown in Figure 3 or 4. Run the supply water inlet line and connect to a
service stop (not provided). Turn on supply water and flush thoroughly .
3. Remove bottom access panel from fountain basin and save the screws. Install the fountain to the wall
using (10) 5/16" bolts and washers (not provided). Bolts should be long enough to securely fasten the
fountain to the wall. T ighten securely , but do not over tighten. Over tightening will crack the fount ain.
4. Remove elbow from end of p-trap and attach it to drain tube. Reattach elbow to p-trap and cut waste
tube to required length using plumbing hardware and trap as a guide.
5. Make water supply connections from service stop to the 3/8" O.D. unplated copper tube coming out of
the tee fitting). Turn on water supply and check for leaks. Newly installed water supply line should be
insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE TEE
AS DAMAGE TO THE O-RINGS MAY RESUL T.
6. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above
105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by reason of
connecting these products to supply line pressures lower than 20 PSIG or higher than 105 PSIG is not
covered by warranty .
7. Check stream height from bubbler. S tream height is factory set at 40-50 PSI. If supply pressure varies
greatly from this, adjust the screw on regulator (item 17) by using a small screwdriver through the small
hole in the push button (item 8)(See Figure 5). Clockwise adjustment will raise stream height and
counter-clockwise will lower stream height. For best adjustment stream height should be approximately
1-1/2" (38mm) above the bubbler guard.
8. Replace bottom access panel to fountain using the screws provided. T ighten securely .
CARE AND MAINTENANCE OF MARBLYTE FOUNTAINS
1. Marblyte provides an extremely durable, nonporous surface which resists staining. Care is very simple.
Routine cleaning with a soft sponge or cloth, or with water or a non-abrasive aerosol foam cleaner , is all
that is normally needed to give many years of trouble free service. Cleaners left standing on the fountain
surface can dull the surface finish. Be certain to rinse all cleaning agents completely and polish with a
soft cloth.
2. Harsh abrasive cleaners are not required and should not be used.
3. Mild abrasives such as liquid automotive cleaning compound or baking soda paste will remove simple
scratches and stains. Cigarette burns can normally be removed without noticeable effect. Deeper
scratches or gouges can be corrected with fine grit sandpaper (240 grit then 400 grit) or a green
scotchbrite pad.
4. T o maintain or regain luster and make cleaning easier , periodic applications of automobile wax or like
products will keep the finish looking like new.
TROUBLE SHOOTING AND MAINTENANCE
1. Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits
may be removed from orifice with a small round file not over 1/8" diameter or a small diameter wire.
CAUTION: Do not file or cut orifice materials.
2. Stream Regulator: If orifice is free of material deposits, regulate flow according to instruction on page
3. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize
an o-ring water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar
while pulling on the tubing (See Figure 2). To insert tubing, push tube straight into the fitting until it
98456C (Rev. B - 12/08)
PAGE 4
Page 5
EDFPVR320RC FTN
PAR TS LIST
PART NO.ITEM NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
45880C
75575C
75570C
15005C
28873C
40045C
55996C
45662C
45738C
50986C
98118C
56087C
56293C
61313C
15028C
70012C
75672C
70852C
45873C
45736C
55994C
56307C
45881C
45879C
56304C
DESCRIPTION
DRAIN
ANTI -ROTA TIONAL BALL
SCREW #10-24 PINNED TORX
NUT - REGULAT OR RET AINING
BOTTOM - COVER
HEX NUT
IN-LINE STRAINER
PUSH BUTTON
PUSH BUTTON SLEEVE
REGULATOR HOLDER
BUBBLER ASSEMBLY
PUSH BUTTON EXTENSION
FOUNTAIN - GRANITE
REGULATOR
NIPPLE ASSEMBL Y
HEX NUT - 3/8-18
SCREW - CAP #6-32 X 5/16
TEE - 3/8"
FERRULE - DRAIN
NUT - REGULATOR MOUNTING
1/4"POLY TUBING (CUT TO LENGTH)
3/8"POLY TUBING (CUT TO LENGTH)
6" TAIL PIPE
T-PIPE 1-1/2 X 1-3/16
GASKET - T-PIPE
812 9
11
2
16
15
FIG. 6
41410
13 19,24,25
21 2122
777
21
17 BASIN 6
FIG. 5
SEE FIG. 6
SEE FIG. 6
20
19
351
INTERNAL TRAP
19
PRINTED IN U.S.A.
22
18
2218
351
BOTTOM COVER
EXTERNAL TRAP
REMOVED
EXTERNAL TRAP
ELKA Y MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
PAGE 5
98456C (Rev. B - 12/08)
24
Loading...