Elkay EDFPBW114FP Installation Manual

EDFPBW114FP EDFPBWM114FP

Installation/Care/Use Manual

®

Swirlflo

Freeze Resistant Fount ain

Installer

T o assure you install this model easily and correctly , PLEASE READ THESE SIMPLE IN­STRUCTIONS BEFORE ST ARTING THE INST ALLA TION. CHECK YOUR INST ALLA TION
FOR COMPLIANCE WITH PLUMBING , ELECTRICAL AND OTHER APPLICABLE CODES.
After installation, leave these instructions with the building owner for future reference. This
Freeze Resistant Fountain is shipped in two separate cartons. The second carton contains
the Freeze Resistant Package LKFRB1 that is installed on an interior heated wall. Refer to
the Freeze Resistant Package for the rough-in dimensions for installation.

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SER VICE PERSON

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. T O WA TER
LINES IS A COMMON PROCEDURE. THIS GROUNDING MA Y BE IN THE BUILDING OR MA Y OCCUR A WA Y
FROM THE BUILDING . THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNT AIN, CREA T ­ING AN ELECTROL YSIS WHICH CAUSES A MET ALLIC T ASTE OR AN INCREASE IN THE MET AL CONTENT
OF THE WA TER. THIS CONDITION IS A VOIDABLE BY USING THE PROPER MA TERIALS AS INDICA TED.
ANY DRAIN FITTINGS PROVIDED BY THE INST ALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALL Y
ISOLA TE THE FOUNT AIN FROM THE BUILDING PLUMBING SYSTEM.

1/4" O.D. TUBE
WATER INLET
TO COOLER

FIG. 1

3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY

NOTE: WATER FLOW

DIRECTION

BUILDING WATER
INLET

SERVICE STOP
(NOT FURNISHED)

Page 1

OPERA TION OF QUICK CONNECT FITTINGS

SIMPLY PUSH IN
TUBE TO ATTACH

TUBE IS

SECURED

IN POSITION

PUSH IN COLLET

TO RELEASE TUBE

PUSHING TUBE IN BEFORE

PULLING IT OUT HELPS TO

RELEASE TUBE

FIG. 2

98400C (Rev. B - 6/08)

12 1/2"
318mm

MAX. WALL
THICKNESS

7 1/4"
184mm

EDFPBW114FP EDFPBWM114FP

EDFPBWM1 14FPC ROUGH-IN

16"
406mm

1/4" (8mm) DIA. HOLES FOR
MOUNTING PLATE TO WALL

SURFACE MOUNTING
PLATE

3/8" (10mm) DIA. HOLES
FOR MOUNTING PLATE
TO WALL (10)

7 7/8"
200mm

26 1/2"
673mm

9 3/4"
248mm

8"
203mm

5 1/4"
133mm

5 1/4"
133mm

1 1/4"
32mm

28 3/4"
730mm

B

A

BACK PANEL

43 5/8"
1108mm

29 1/4"
743mm

19 3/4"
502mm

21 15/16"
557mm

22 15/16"
583mm

1 5/8"
41mm

33 15/16"
863mm

27"

686mm
ADA
REQUIREMENT

FINISHED FLOOR

FIG . 3 Rough-in for EDFPBWM1 14FP

19"
483mm

12"

305mm
MAX. WALL
THICKNESS

13 3/8"
339mm

FINISHED FLOOR

2 5/8"
66mm

3 5/8"
91mm

FIG . 4 Rough-in Assembly for EDFPBWM114FP

NOTE: REINFORCE WALL IN SHADED AREAS.

LEGEND:
A = 7/8" (22mm) DIA. HOLE FOR W A TER SUPPL Y TUBE
B = 1-3/4" (44mm) DIA. HOLE FOR WASTE LINE

*Note: All dimensions are taken from the finished floor on the side of the wall
that the fountain is installed on.

98400C (Rev. B - 6/08)

Page 2