Elkay 3875A-1, 750A-2, 2235-1, 760A-2, 320A-1 User guide

Instruction Guide

BROOK DESIGN HARDWARE LTD

BDH

BDH

BROOK DESIGN
HARDWARE LTD

BDH

BROOK DESIGN
HARDWARE LTD

–

PUSHBUTTON &
TOUCH SENSOR/
REMOTE TIMER

3875A-1 / 750A-2 / 2235-1 /

760A -2 / 320A-1

3 wire

The Pushbutton & Touch Sensor /
Remote Timer (3 wire) are part of the
Elkay family of switches, timers and
detectors which save energy and
increase convenience in and around
your home, garden or premises.

Rating at 240V ac

• All general load t ypes 16A

• Time Delay: 2 min - 2 hrs

• Blue locator ring

• Time cancellation functions

• Countdown LED

• Fits 25mm back boxes

Usage

The Pushbutton & Touch sensor / Remote
Timer are general purpose time controls.
Appplications for suitable use include
lighting, heating and ventilation. Timers can
be used independently or as a master
when the using Activator trigger switches.

Mounting and Installation
IMPORTANT Please note that it is essential

that the Live In wire and switch Live Out is

identied prior to commencing installation.
Turn o mains supply installation.

Your Elkay
gang, 25mm deep, British Standard

unit is compatible with a single

accessory plate. Please ensure that the top

and bottom lugs are removed, if tted,
from metal wall boxes prior to tting. Ensure

that there is adequate space for wiring.

Step 1 – Place the Live In wire into the left hand

position of the connector, the switched Live
Out wire into the second from left position of
the connector and neutral into right hand
position of connector (See diagram 1).

Step 2

switches one through four. Depending
on required time available from 2 minutes to
2 hours, e.g. 10 minutes - switch one - OFF,
switch two - ON, switch three - OFF,
switch four - OFF (See diagram 2).

Step 3

locator ring will light up around the
pushbutton / touch pad. Your light source or

appliance will now be switched o.

Please refer to operation section.

–

To set time, as per timing table, use

–

Re-apply mains supply. The blue

Diagram 1

LIVE IN

NEUTRAL

LIVE OUT

5 - 7m

4 - 6m

5 - 7m

3 - 4m

5 - 7m

4 - 6m

5 - 7m

3 - 4m

LIVE IN

LIVE OUT

NEUTRAL

7 metres approx

.

2.4 metres

7 metres approx.

CEILING

FLOOR

LIVE IN

NEUTRAL

LIVE OUT

LIVE IN

LIVE OUT

Battery

LIVE IN

LIVE OUT

DIL

switches

Battery

NEUTRAL

BROOK DESIGN HARDWARE LTD

BDH

B

BDH

BROOK DESIGN
HARDWARE LTD

Diagram 2 – Time settings

Please note:

The black bar denotes
the positio n of the dip swi tch.

4
3
2

ON DIP

1

2 mins 5 mins 10 mins 15 mins 20 mins 30 mins 40 mins 60 mins

4
3
2

ON DIP

1

50 mins 60 mins 70 mins 80 mins 90 mins 100 mins 110 mins 120 mins

ON DIP

ON DIP

4
3
2
1

4
3
2
1

ON DIP

ON DIP

4
3
2
1

4
3
2
1

ON DIP

ON DIP

4
3
2
1

4
3
2
1

ON DIP

ON DIP

4
3
2
1

4
3
2
1

ON DIP

ON DIP

4
3
2
1

4
3
2
1

ON DIP

ON DIP

4
3
2

ON DIP

1

4
3
2

ON DIP

1

4
3
2
1

4
3
2
1

Activator and Momentary Fitting

When connecting with Elkay activators use
three core cable connecting the live in,
live out and trigger terminals as shown in
Diagram 1. Please note that the TRIGGER
terminal is the third terminal between
live out and neutral. Retractive or
Momentary switches will work with this
product when looped with the live in
and trigger terminals.

Operation of the Unit

1. Press the pushbutton/touch pad and the
red LED will light up. Your light source or
appliance will now be switched ON.

2. At any time during the working of the
light source or appliance, the
pushbutton/touch pad can be pressed
to reset the timing sequence to the

Important Notice

All wiring should be carried out by a competent

person or a qualifi ed electrician and should be
fi tted to current IEE wiring regulations BS 7671.

The circuit should be isolated before carrying out
any work. Failure to adhere to the instructions
will invalidate the warranty.

Brook House,
Dunmurry Industrial Estate,
Dunmurry,
Belfast BT17 9HU

T [phone]
F [phone]
E [e-mail]

Elkay ( Europe), 51C Milic ka, Trzebnic a, 55-100, Pola nd

Technical Helpline

For fu rther help o r assista nce or informa tion on this o r other prod ucts in the r ange
please call the Elkay Technical team on [phone]. Please call the
Technica l helpline before ret urnin g any pro duct s to your stock ist. These
are available in other languages. Please refer to our website www.elkay.co.uk

Instrukcje są również dostępne w innych językach. Prosimy o zapoznanie się z naszą
stroną internetową www.elkay.co.uk lub www.elkaypolska.pl

elkay.co.uk

originally set time, e.g. when the timing
period is 30 minutes. If pushbutton/

touch pad is pressed 15 minutes into

the sequence, the timer will re-set for a
further 30 minutes.

3. To end the timing sequence prematurely,
press and hold the pushbutton/touch

pad until the red LED fl ashes

continuously indicating the last minute
of operation. Your light source or
appliance will be switched OFF, after
one minute.

4. At one minute prior to the end of the
timing sequence, the red LED will begin

to fl ash continuously for the last

minute of operation. The blue locator

ring will then illuminate once the light

source or appliance has gone o .

instructions

DH

BROOK DESIGN
HARDWARE LTD