Elk 982, 982K User Manual
Cell-Pack
Power Supply , and Enclosure for
Cellular Alarm Transceiver
APPLICATION
The ELK-982(K) Cell-Pack is ideal for Cellular Alarm
Transceivers. It consists of a metal enclosure and 12 Volt
DC power supply/battery charger. It supplies 1 Amp
continuous current and 2.5 Amps peak for the brief high
current demands of the radio during transmission. The
design of the enclosure allows quick and easy field
mounting of the transceiver and antenna.
FEATURES
• Supplies 12 Volts D.C. Power for Transceiver
• Current: 2.5A Peak, 1A Continuous
• Heavy Duty Metal Enclosure
INSTALLATION
1. Mount transceiver in top right corner by sliding
antenna thru rubber grommet and securing the
bottom using hardware supplied. (see page 2)
2. Mount the ELK-P624 power supply board into the
enclosure as shown.
3. Wire as per the Cellular Transceiver instructions.
4. Connect Transformer and Battery after all wiring
is complete.
Transformer
16.5 VAC
45 VA
* See Note
* Note:
Battery (ELK-1250) &
Transformer (ELK-TRG1640)
Included with ELK-982K
Sold Separately for ELK-982
JP1
JP1 ON
JP2
JP2 OFF
Do Not Move Jumpers
ELK-624 12V POWER SUPPLY
TRANSFORMER
AC
- +
DC OUTPUT
LEDS
AC DC
+
BATTERY
ELK-982
ELK-982K
Cellular
Alarm Transceiver
Refer to the Cellular Transceiver
Instructio ns for Connections
Optional hookup
for Transmission
Shunt (if available)
-
-
Transceiver
12 Volts D.C.
Power Input
+
Includes Battery
& Transfomer
Bell / Alarm
Input
-
+
Control Panel
Line Fault output
Relay (contacts closed to
halt radio transmissions)
Bell / Alarm output
OPERATION
This hookup example shows the Transmission Shunt
Mode of operation. Control panel's that have phone
line fault monitoring will halt radio transmissions while
the phone line is good. Relay contacts on the control
panel will be closed to shunt any possible radio
transmissions.
If your control does not have line fault monitoring,
see ELK-981 which provides line fault monitoring
with power supply.
Features and Specifications subject to change without notice.
For Technical Support on the Numerex Technologies
Digicell Transceiver, call 888-987-5465.
+
-
(Grn)(Red)
AC DC Indication
ON / ON AC input is on / DC output is on. Normal.
OFF / ON AC input is off / DC out put is from Battery only. Step
ON / OFF AC input is on / DC output is off. The auto -re set
OFF /OFF AC input is off / DC output is off.
LED Status Indicat or s
down Transformer is defective or unplugged, or the
AC outle t is off. Battery will eventually discharge.
overload protector is likely open due to an ov erload
short circuit.
Red
Battery
12 Volt
* See Note
Black
P.O. Box 100 • Hildebran, NC 28637 USA • 828-397-4200 • 828-397-4415 FAX
http://www.elkproducts.com • email: info@elkproducts.com
03/04
Transceiver Mounting Location for this Model
Place
Plug
Here
Slide Transceiver
Over Mounting Plate
to Secure it in Place
Place
Antenna
Grommet
Here
Secure Mounting
Plate Here
Transceiver Mounting Location for this Model
Secure Transceiver
with Washer and Nut
Here
Place
Plug
Here
Place
Antenna
Grommet
Here
Place
Standoff
Here
Loading...