Elitegroup PV-28SV55-CN-CP-GN-GP-1, PV-28SV50-BN-BP-1 User Manual

INSTALLATION INSTRUCTIONS

tis

™

AND

OWNER’S MANUAL

POWER-VENT

HIGH-EFFICIENCY

FIREPLACE WITH

BAY WINDOW

MODELS

PV-28SV50-(BN,BP)-1

PV-28SV55-(CN,CP,GN,GP)-1

Installer: Leave this manual with the

appliance.

Consumer: Retain this manual for future

reference.

WARNING: If the information in these instructions are not followed exactly, a ﬁre or explosion may result causing property damage, personal injury or loss of life.

— Do not store or use gasoline or other ﬂamma-

ble vapors and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre department.

— Installation and service must be performed

by a qualiﬁed installer, service agency or the gas supplier.

EFFECTIVE DATE

MAY 2007

This appliance is NOT to be installed in Canada.

This appliance may be installed in an aftermarket, permanently located, manufactured home (USA only) or mobile home, where not prohibited by state or local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁed kit is used.

WARNING: If not installed, operated and maintained in accordance with the manufacturer’s instructions, this product could expose you to substances in fuel or from fuel combustion which can cause death or serious illness.

22618-12-0707 Page 1

TABLE OF CONTENTS

SECTION PAGE

Important Safety Information ......................................................................................................................................... 3

Safety Information for Users of LP-Gas ......................................................................................................................... 4

Requirements for Massachusetts ..................................................................................................................................... 5

Gas Supply ...................................................................................................................................................................... 6

Introduction ..................................................................................................................................................................... 7

Installation Instructions – General Safety Information ................................................................................................... 8

Speciﬁcations .................................................................................................................................................................. 8

Clearances for Direct Vent .............................................................................................................................................. 9

Heater Installation for Direct Vent .................................................................................................................................. 9

Clearances for Single Flue ............................................................................................................................................ 10

Heater Installation for Single Flue ................................................................................................................................ 10

Speciﬁcations ........................................................................................................................................................ 11 – 14

Clearance to Combustibles ........................................................................................................................................... 15

Rough Framing Dimensions ......................................................................................................................................... 16

Insert Into Masonry Fireplace ....................................................................................................................................... 16

Wall Clearances ............................................................................................................................................................. 17

Log Set Installation Instructions ................................................................................................................................... 18

Vent Examples for Single Flue .............................................................................................................................. 19 - 21

PVVK-CFA Flex Vent Kit ............................................................................................................................................. 22

PVVK-SH Horizontal Vent Adaptor Kit ....................................................................................................................... 23

Horizontal Examples for Colinear Direct Vent ............................................................................................................. 24

Vertical Examples for Colinear Direct Vent ........................................................................................................... 25 - 26

PVCA Horizontal Colinear Direct Vent Adaptor .......................................................................................................... 27

PVVTC Termination Cap Vent Kit ............................................................................................................................... 28

PVCT Colinear Transition Vent Kit .............................................................................................................................. 29

Direct Vent Installation Instructions ...................................................................................................................... 30 - 31

PVVK-24H and PVVK-48H Vent Kit ................................................................................................................... 32 - 33

Gas Connection Installation Instructions ...................................................................................................................... 34

Operating Instructions Checklist ................................................................................................................................... 35

Lighting Instructions .............................................................................................................................................. 36 - 37

Fan Operation ................................................................................................................................................................ 38

Gas Conversion Instructions .................................................................................................................................. 39 - 40

Automatic Humidiﬁer Operation .................................................................................................................................. 41

Optional Controllers ................................................................................................................................................ 42 - 43

Wiring ........................................................................................................................................................................... 44

General Information ...................................................................................................................................................... 45

Maintenance ........................................................................................................................................................... 45 - 46

Unit Operating Faults .................................................................................................................................................... 47

Resetting the Heater ...................................................................................................................................................... 47

Log Placement .............................................................................................................................................................. 47

Main Convection Fan .................................................................................................................................................... 48

Heat Exchanger ............................................................................................................................................................. 48

Surround Installation Instructions ................................................................................................................................. 48

Pedestal Installation Instructions .................................................................................................................................. 49

Parts List ................................................................................................................................................................ 50 - 51

Parts View .............................................................................................................................................................. 52 - 53

Warranty Terms ............................................................................................................................................................. 54

How To Order Repair Parts ........................................................................................................................................... 55

Service Notes ......................................................................................................................................................... 55 - 56

22618-12-0707Page 2

IMPORTANT SAFETY INFORMATION

THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.

• Due to high temperatures the appliance should be located out of trafﬁc and away from furniture and draperies.

• Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the appliance.

• Clothing or other ﬂammable material should not be placed on or near the appliance.

• Any safety screen or guard removed for servicing an ap pliance must be replaced prior to operating the appliance.

• Keep burner and control compartment clean.

• Vent cap hot while furnace is in operation.

• For manufactured home (USA only) or mobile home or residential installation convertible for use with natu ral gas and liqueﬁed petroleum gases when provision is made for the simple conversion from one gas to the other.

• Installation and repair should be done by a QUALIFIED SERVICE PERSON. The appliance should be inspected before use and at least annually by a qualiﬁed service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding materials, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.

• DO NOT put anything around the furnace that will ob struct the ﬂow of combustion and ventilation air.

• DO keep the appliance area clear and free from combus

tible material, gasoline and other ﬂammable vapors and liquids.

• Do examine venting system periodically and replace damaged parts.

• Do make a periodic visual check of burner. Clean and replace damaged parts.

• DO NOT use this heater if any part has been under wa ter. Immediately call a qualiﬁed service technician to inspect the heater and to replace any part of the control system and any gas control which has been under water.

22618-12-0707 Page 3

SAFETY INFORMATION FOR USERS OF LP-GAS

Propane (LP-Gas) is a ﬂammable gas which can cause ﬁres and explosions. In its natural state, propane is odorless and colorless. You may not know all the following safety precautions which can protect both you and your family from an accident. Read them carefully now, then review them point by point with the mem-

LP-GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.

That’s your signal to go into immediate action!

• Do not operate electric switches, light matches, use your phone. Do not do anything that could ignite the gas.

• Get everyone out of the building, vehicle, trailer, or area. Do that IMMEDIATELY.

• Close all gas tank or cylinder supply valves.

• LP-Gas is heavier than air and may settle in low areas such as basements. When you have reason to suspect a gas leak, keep out of basements and other low areas. Stay out until ﬁreﬁghters declare them to be safe.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell the odor of the chemical put into the gas. You must ﬁnd out if you can smell the odorant in propane. Smoking can decrease your ability to smell. Being around an odor for a time can affect your sensitivity or ability to detect that odor. Sometimes other odors in the area mask the gas odor. People may not smell the gas odor or their minds are on something else. Thinking about smelling a gas odor can make it easier to smell.

The odorant in LP-gas is colorless, and it can fade under some circumstances. For example, if there is an underground leak, the movement of the gas through soil can ﬁlter the odorant. Odorants

bers of your household. Someday, there may not be a minute to lose, everyone’s safety will depend on knowing exactly what to do. If, after reading the following information, you feel you still need more information, please contact your gas supplier.

• Use your neighbor’s phone and call a trained LP-Gas ser vice person and the ﬁre department. Even though you may not continue to smell gas, do not turn on the gas again. Do not re-enter the building, vehicle, trailer, or area.

• Finally, let the service man and ﬁreﬁghters check for escaped gas. Have them air out the area before you return. Properly trained LP-Gas service people should repair the leak, then check and relight the gas appliance for you.

in LP-Gas also are subject to oxidation. This fading can occur if there is rust inside the storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or into walls, masonry and other materials and fabrics in a room. That will take some of the odorant out of the gas, reducing its odor intensity.

LP-Gas may stratify in a closed area, and the odor intensity could vary at different levels. Since it is heavier than air, there may be more odor at lower levels. Always be sensitive to the slightest gas odor. If you detect any odor, treat it as a serious leak. Imme diately go into action as instructed earlier.

SOME POINTS TO REMEMBER

• Learn to recognize the odor of LP-gas. Your local LP-Gas Dealer can give you a “Scratch and Sniff” pamphlet. Use it to ﬁnd out what the propane odor smells like. If you suspect that your LP-Gas has a weak or abnormal odor, call your LP-Gas Dealer.

• If you are not qualiﬁed, do not light pilot lights, perform service, or make adjustments to appliances on the LP-Gas system. If you are qualiﬁed, consciously think about the odor of LP-Gas prior to and while lighting pilot lights or performing service or making adjustments.

• Sometimes a basement or a closed-up house has a musty smell that can cover up the LP-Gas odor. Do not try to light pilot lights, perform service, or make adjustments in an area where the conditions are such that you may not detect the odor if there has been a leak of LP-Gas.

• Odor fade, due to oxidation by rust or adsorption on walls of new cylinders and tanks, is possible. Therefore, people should be particularly alert and careful when new tanks or cylinders are placed in service. Odor fade can occur in new tanks, or reinstalled old tanks, if they are ﬁlled and allowed

to set too long before reﬁlling. Cylinders and tanks which have been out of service for a time may develop internal rust which will cause odor fade. If such conditions are suspected to exist, a periodic sniff test of the gas is advisable. If you have any question about the gas odor, call your LP-gas dealer. A periodic sniff test of the LP-gas is a good safety measure under any condition.

• If, at any time, you do not smell the LP-Gas odorant and you think you should, assume you have a leak. Then take the same immediate action recommended above for the occasion when you do detect the odorized LP-Gas.

• If you experience a complete “gas out,” (the container is under no vapor pressure), turn the tank valve off immediately. If the container valve is left on, the container may draw in some air through openings such as pilot light oriﬁces. If this occurs, some new internal rusting could occur. If the valve is left open, then treat the container as a new tank. Always be sure your container is under vapor pressure by turning it off at the container before it goes completely empty or having it reﬁlled before it is completely empty.

22618-12-0707Page 4

REQUIREMENTS FOR MASSACHUSETTS

For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above ﬁnished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisﬁed:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas ﬁtter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the ﬂoor level where the gas equipment is to be installed. In addition, the installing plumber or gas ﬁtter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualiﬁed licensed professionals for the installation of hard wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas

fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent ﬂoor level.

b. In the event that the requirements of this subdivision can

not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/ UL 2034 listed and IAS certiﬁed.

3. SIGNAGE. A metal or plastic identiﬁcation plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a) 1 through 4.

(b) EXEMPTIONS: The following equipment is exempt

from 248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled

“Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

2. Product Approved side wall horizontally vented gas

fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes.

(d) MANUFACTURER REQUIREMENTS - GAS

EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the ﬂue gases, but identiﬁes “special venting systems”, the following requirements shall be satisﬁed by the manufacturer:

1. The referenced “special venting system” instructions

shall be included with the appliance or equipment installation instructions; and

2. The “special venting systems” shall be Product

Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instruction.

(e) A copy of all installation instructions for all Product

Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

22618-12-0707 Page 5

GAS SUPPLY

FLEX TUBING

3/8 NPT NIPPLE

FLARE FITTING

GAS VALVE

SOLENOID

FLARE SHUT OFF VALVE

Consult the current National Fuel Gas Code, ANSI Z223.1 CAN/ CGA-B149 (.1 or .2) installation code.

Recommended Gas Pipe Diameter

Pipe Length Schedule 40 Pipe

Inside Diameter

Tubing, Type L

Outside Diameter

Nat. L.P. Nat. L.P.

0-10 feet

0-3 meters

10-40 feet

4-12 meters

40-100 feet

13-30 meters

100-150 feet

31-46 meters

1/2”

12.7mm

1/2”

12.7mm

1/2”

12.7mm

3/4”

19mm

3/8”

9.5mm

1/2”

12.7mm

1/2”

12.7mm

1/2”

12.7mm

1/2”

12.7mm

5/8”

15.9mm

3/4”

19mm

7/8”

22.2mm

3/8”

9.5mm

1/2”

12.7mm

1/2”

12.7mm

3/4”

19mm

Note: Never use plastic pipe. Check to conﬁrm whether your local codes allow copper tubing or galvanized.

Note: Since some municipalities have additional local codes, it is always best to consult your local authority and installation code.

The use of the following gas connectors is recommended: — ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing

and Fittings

— ANS Z21.45 Assembled Flexible Appliance Connectors of

Other Than All-Metal Construction

The above connectors may be used if acceptable by the authority having jurisdiction. The state of Massachusetts requires that a ﬂexible appliance connector cannot exceed three feet in length.

Figure 1

Installing a New Main Gas Cock

Each appliance should have its own manual gas cock.

A manual main gas cock should be located in the vicinity of the unit. Where none exists, or where its size or location is not ad equate, contact your local authorized installer for installation or relocation.

Compounds used on threaded joints of gas piping shall be resistant to the action of liqueﬁed petroleum gases. The gas lines must be checked for leaks by the installer. This should be done with a soap solution watching for bubbles on all exposed connections, and if unexposed, a pressure test should be made.

Never use an exposed ﬂame to check for leaks. Appliance must be disconnected from piping at inlet of control valve and pipe capped or plugged for pressure test. Never pressure test with appliance connected; control valve will sustain damage!

A gas valve and ground joint union should be installed in the gas line upstream of the gas control to aid in servicing. It is required by the National Fuel Gas Code that a drip line be installed near the gas inlet. This should consist of a vertical length of pipe tee connected into the gas line that is capped on the bottom in which condensation and foreign particles may collect.

Pressure Testing of the Gas Supply System

1. To check the inlet pressure to the gas valve, a 1/8" (3mm) N.P.T.

plugged tapping, accessible for test gauge connection, must be placed immediately upstream of the gas supply connection to the appliance.

2. The appliance and its individual shutoff valve must be

disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).

3. The appliance must be isolated from the gas supply piping

system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).

Attention! If one of the procedures results in pressures in excess of 1/2 psig (14" w.c.) (3.5 kPa) on the ﬁreplace gas valve, it will result in a hazardous condition.

Checking Manifold Pressure

Both Propane and Natural gas valves have a built-in pressure regulator in the gas valve. Natural gas models will have a manifold pressure of approximately 3.5" w.c. (.872kPa) at the valve outlet with the inlet pressure to the valve from a minimum of 5.0" w.c. (1.245kPa) for the purpose of input adjustment to a maximum of

10.5" w.c. (2.614kPa) Propane gas models will have a manifold

pressure approximately 10.0" w.c. (2.49kPa) at the valve outlet with the inlet pressure to the valve from a minimum of 11.0" w.c. (2.739kPa) for the purpose of input adjustment to a maximum of

13.0" w.c. (3.237kPa).

A 1/8" (3mm) N.P.T. plugged tapping, accessible for test gauge connection, is located on the outlet side of the gas control.

22618-12-0707Page 6

INTRODUCTION

Introduction

Always consult your local Building Department regarding regu lations, codes or ordinances which apply to the installation of a direct vent wall furnace.

Instructions to Installer

1. Installer must leave instruction manual with owner after installation.

2. Installer must have owner ﬁll out and mail warranty card supplied with furnace.

3. Installer should show owner how to start and operate furnace and thermostat.

4. Installer must locate unit near a grounded wall receptacle for 115VAC power and must provide gas supply and vent the unit properly for safe operation.

Warning: Any change to this furnace or its control can be dangerous. This is a heating appliance and any panel, door or guard removed for servicing an appliance must be replaced prior to operating the appliance.

General Information

This series is designed certiﬁed in accordance with American National Standard/CSA Standard Z21.88 and CSA 2.33 by the Canadian Standards Association as a Gas Fireplace Heater to be installed according to these instructions.

Any alteration of the original design, installed other than as shown in these instructions or use with a type of gas not shown on the rating plate is the responsibility of the person and com pany making the change.

Important

All Correspondence should refer to complete Model Number, Serial Number and type of gas.

Notice: During initial ﬁring of this unit, oil from the heat exchanger may bake out and smoke may occur. To prevent triggering of smoke alarms, ventilate the room in which the unit is installed.

Installation in Residential Garages

Gas utilization equipment in residential garages shall be installed so that all burners and burner ignition devices are located not less than 18” (457mm) above the ﬂoor.

Such equipment shall be located, or protected, so it is not subject to physical damage by a moving vehicle.

Qualiﬁed Installing Agency

Installation and replacement of gas piping, gas utilization equip-

ment or accessories and repair and servicing of equipment shall be performed only by a qualiﬁed agency. The term “qualiﬁed agency” mean any individual, ﬁrm, corporation or company which either in person or through a representative is engaged in and is responsible for (a) the installation or replacement of gas piping or (b) the connection, installation, repair or servicing of equipment, who is experienced in such work, familiar with all precautions required and has complied with all the requirements of the authority having jurisdiction. The installation must conform with local codes, or in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1/NFPA 54 or Natural Gas and Propane Installation Code, CSA B149.1. * Available from the American National Standards Institute, Inc., 11 West 42nd St., New York, NY 10036.

A manufactured home (USA only) or mobile home OEM instal lation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable, the Standard for Manufactured Home Installations, ANSIZ225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.0.

Sate of Massachusetts: The installation must be made by a licensed plumber or gas ﬁtter in the Commonwealth of Massachusetts.

High Altitudes

For altitudes/elevations above 2,000 feet (610m), input ratings

should be reduced at the rate of 4 percent for each 1,000 feet (305m) above sea level, this may be accomplished by reducing manifold pressure. The maximum allowable reduction in manifold pressure for Natural gas shall be from 3.5” w.c. (.872kPa) to 2.8” w.c. (.697kPa). The maximum allowable reduction in manifold pressure for Propane (LP) gas shall be from 10.0” w.c. (2.49kPa) to 8.0” w.c. (1.99kPa). For Canadian high altitude applications, this appliance is suitable for installation at elevations between 0 feet (0m) and 4,500 feet (1,372m) without change.

Canada:

This appliance is NOT to be installed in Canada.

22618-12-0707 Page 7

INSTALLATION INSTRUCTIONS - GENERAL SAFETY INFORMATION

1. This installation must conform with local codes or, in the absence of local codes with NFPA54.

2. Provide adequate clearances around the product for servic ing and ensure there are no obstructions to the combustion air intake situated at the back of the heater. Refer to Page 15, Figures 7 through 10.

3. The appliance must be installed on a ﬂat, solid

continuous surface (i.e. wood, metal, concrete). Please Note: Rough or uneven surfaces can cause vibration or humming in the heater.

4. The Mantis Power-Vent High-Effeciency Fireplace can be in stalled in a wide variety of ways and will ﬁt nearly any room layout. It may be installed in a recessed position, framed out into the room, or across a corner. For installation options refer to page 15.

5. This appliance (Insert and Freestanding Models) needs to be installed in such a way that the heater can be

removed at all times to service the heater exchanger and ﬂue fan located in the rear section of the heater.

Note: Under no circumstances should the appliance be in

stalled under conditions which would not allow for

easy removal of the appliance to carry out routine inspection and service to the appliance, to do so will void the warranty.

Note: On Single Wall ﬂue pipe installations (imitation zero

clearance ﬁreplace) a minimum of 2” (50.8cm) clearance must be provided at the rear of the heater to enable the heater to get sufﬁcient combustion air to the air inlet located at the rear of heater. Refer to installation instructions on page 15, Figures 7 through 10.

Note: Where a mantel surround is being used on insert installa-

tions and zero clearance ﬁreplace installations, the combustion air intake slot located in the top mantel surround must have no obstructions to allow combustion air to enter through the slot to the combustion air inlet located at the back of the heater.

SPECIFICATIONS

Model PV28SV50

Input BTU/HR (KW/H) 19,000 Rear - 9,000 Front

Height 25 1/8”

Width 28 3/16”

Depth 17 5/8”

Gas Inlet (Pipe) 3/8” Flair

Electrical - Unit has a 5’ (1.5m) 3 pronged cordset for con-

nection to an approved 115 VAC 60HZ maximum AMPs - 5A wall receptacle.

Accessories

Part Number Description

PV-2H Top Cover - Slim Assembly

PV-4H Top Cover - Short Assembly

PVPK Pedestal Kit

PVE-1 6” Surround Assembly

PVSH Rear Shroud

TRW Wall Thermostat - Wireless Remote

FRBTC Battery Operated Remote w/Thermostat

FRBTP Battery Operated Remote w/Programmable Ther-

mostat

TMV2 Two-Stage Thermostats

CIPFP-1 Floor Pad Kit

CIFPB-1C Corner Floor Pad Kit

PVVK24H Direct Vent 24” Vent Kit

PVVK48H Direct Vent 48” Vent Kit

PVVK-SH Single Flue Horizontal Vent Kit

PVVK-SV Single Flue Vertical Vent Kit

PVVK-CFA Flex Vent Kit

PVCT Colinear Transition

PVVTC Vertical Termination Cap - 1.5”

PVCA Colinear Adapter

22618-12-0707Page 8

CLEARANCES FOR DIRECT VENT

1 9/16”

4 3/32”

1. Pick a location on a wall with a clear space in the room. In selecting a location for installation, it is necessary to provide adequate accessibility clearances for servicing and proper installation. Be sure to locate the unit close enough to a 110 VAC wall receptacle to properly power appliance.

2. When facing the front of the furnace the minimum clearances from casing to combustible construction are 0” (0mm) on top, 0” (0mm) on each side, recommend 4” (102mm) on sides for servicing and 0”(0mm) from the ﬂoor, 0” (0mm) to rear wall and 40” (1016mm) from Mantis top to ceiling.

3. The minimum distance from the center of the vent cap to the nearest outside corner or obstruction is 12” (305mm).

4. The minimum wall depth is 4” (102mm) and the maximum is 48” (121.92cm).

The vent terminal of a direct vent appliance, with an input of 50,000 BTU (14.6KW) per hour or less shall be located at least 9” (229mm) from any opening through which ﬂue gases could enter a building.

The bottom of the exhaust vent terminal and the air intake shall be located at least 12” (305mm) above grade and must be vented outside.

WARNING: The nearest point of the vent cap should be a minimum horizontal distant of six (6) feet (1.83m) from any pressure regulator. In case of regulator malfunction, the six (6) feet (1.83m) distance will reduce the chance of gas entering the vent cap.

Installation on Rugs and Tile

If this appliance is to be installed directly on carpeting, tile, or other combustible material, other than wood ﬂooring, the appliance shall be installed on a metal or wood panel extending the full width and depth of the appliance.

The base referred to above does not mean the ﬁre-proof base as used on wood stoves. The protection is primarily for rugs that may be extremely thick and light-color tile that can discolor.

HEATER INSTALLATION FOR DIRECT VENT

Locating Wall Opening

The recommended location for this furnace is on an outside wall. Locate wall studs so that wall vent opening will be located between wall studs. The wall opening required for venting is a 3 1/2” (89mm) minimum diameter opening.

Refer to Figures 3 and 6 for positioning the heater on wall and for locating gas line connection and vent opening. Furnace can sit on the ﬂoor.

Figure 2

22618-12-0707 Page 9

CLEARANCES FOR SINGLE FLUE

2. When facing the front of the furnace, the minimum clearances from casing to combustible construction are 0” (0mm) on top, 0” (0mm) on each side, recommend 4” (102mm) for servicing and 0” (0mm) from the ﬂoor and 2” (51mm) to rear wall for servicing and installation.

3. The minimum distance from the center of the vent cap to the nearest outside corner or obstruction is 12” (305mm).

The bottom of the exhaust vent terminal and the air intake shall be located at least 12” (305mm) above grade and must be vented outside.

WARNING: The nearest point of the vent cap should be a minimum horizontal distance of six (6) feet (1.83m) from any pressure regulator. In case of regulator malfunction, the six (6) feet (1.83m) distance will reduce the chance of gas entering the vent cap.

Installation on Rugs and Tile

The base referred to above does not mean the ﬁre-proof base as used on wood stoves. The protection is primarily for rugs that may be extremely thick and light-color tile that can discolor.

HEATER INSTALLATION FOR SINGLE FLUE

Locating Wall Opening

The recommended location for this heater is on an outside wall (the unit can be located on an inside wall but must not exceed 40’ (12.192m) in exhaust vent length). Locate wall studs so that wall vent opening will be located between wall studs. The wall opening required for venting is a 1 7/8” (48mm) minimum diameter opening.

Refer to Figures 3 to 6 for positioning the heater on wall and for locating gas line connection and vent opening. Heater can sit on the ﬂoor.

22618-12-0707Page 10

SPECIFICATIONS

Heater with Pedestal and Single Flue Adaptor

1 Flue Outlet 1 1/2” PVC Pipe

2 Air Inlet

3 Electric Cord

4 3/8” Flare Connection (Inside)

5 Single Flue Adaptor Model #PVVK-SH (required)

Figure 3

22618-12-0707 Page 11

SPECIFICATIONS - (continued)

Heater without pedestal

1 Flue Outlet 1 1/2” PVC Pipe

2 Air Inlet

3 Electric Cord

4 3/8” Flare Connection (Inside)

5 Single Flue Adaptor Model #PVVK-SH (required)

Figure 4

22618-12-0707Page 12

SPECIFICATIONS - (continued)

Fireplace Insert with Mantel Surround with Slim Top Panel

1 Flue Outlet 1 1/2” PVC Pipe

2 Air Inlet

3 Electric Cord

4 3/8” Flare Connection (Inside)

5 Single Flue Adaptor Model #PVVK-SH (Required)

6 Surround Model #PVE-1

7 Top Cover Kit, Slim Model #PV2H

Caution: Do not block louver in surround. Note: Verify ﬁreplace opening dimensions using Figure 9, page 15.

Figure 5

22618-12-0707 Page 13

SPECIFICATIONS - (continued)

Fireplace Insert with Mantel Surround with Short Top Panel

1 Flue Outlet 1 1/2” PVC Pipe

2 Air Inlet

3 Electric Cord

4 3/8” Flare Connection (Inside)

5 Single Flue Adaptor Model #PVVK-SH (Required)

6 Surround Model #PVE-1

8 Top Cover Kit, Short Model #PV4H

Caution: Do not block louver in surround. Note: Verify ﬁreplace opening dimensions using Figure 9, page 15.

Figure 6

22618-12-0707Page 14

CLEARANCE TO COMBUSTIBLES

B B

12”

18”

24”

8”

6”

4”

COMBUSTIBLE TRIM AND MANTELS

ALLOWED

IN SHADED AREA

40”

CEILING

Freestanding Models

Figure 7 Figure 8

Freestanding Units

A Rear Wall to Heater 0” (2” Single Flue and 1 1/4” Direct Vent for Serviceability)

B Side Wall to Heater 0” (4” recommended for serviceability)

C Corner Installation 0”

D Mantel Clearance See Figure 11

Fireplace Insert

Single Flue

Requires surround for combustion air.

Do not cover surround louver.

Figure 9

Direct Vent Installation Shown

Mantel and Ceiling Clearances

Figure 11

Single Flue requires surround for combustion air.

Figure 10

Note: The Mantis Power-Vent High-Efﬁciency Fireplace has been tested and approved for zero clearance to combustible materials.

Empire Comfort Systems, Inc. recommends that clearances as listed above should be maintained to allow for removal of the product for servicing.

22618-12-0707 Page 15

ROUGH FRAMING DIMENSIONS

A - 13 /34” MIN. CO-LINEAR

8 1/2” WHEN USING DIRECT VENTING PVVK-24H/PVVK-48H

NOTE: DIMENSIONS FOR USE WITH SHORT TOP

PV4H. THIS IS RECOMMENDED FOR UNIT SERVICEABILITY.

B - 25 1/8”

C - 28”

NOTE: IF TRIM AROUND HEATER IS NECESSARY,

THE SURROUND KIT PVE-1 MUST BE USED, AND SUBTRACT 1” FROM (A) DIMENSION.

Figure 12

INSERT INTO MASONRY FIREPLACE

A - 12 3/4” MIN. SHORT TOP PV4H

17 13/16” MIN. SLIM TOP PV2H USING PVE-1 SURROUND KIT

B - 25 1/8” MIN. DIRECT VENT

26 1/2” MIN. SINGLE FLUE 29” MAX

C - 28” MIN. NO SURROUND

33” MIN. WITH PVE-1 SURROUND 35” MAX. WITH PVE-1 SURROUND

Figure 13

22618-12-0707Page 16

WALL CLEARANCES

Figure 14

22618-12-0707 Page 17

+ 39 hidden pages