Elitegroup 259EI User Manual

i -1

Notice

The information in this user’s manual is subject to change without notice.

THE MANUFACTURER OR RESELLER SHALL NOT BE LIABLE FOR ERRORS
OR OMISSIONS CONTAINED IN THIS MANUAL AND SHALL NOT BE LIABLE
FOR ANY CONSEQUENTIAL DAMAGES, WHICH MAY RESULT FROM THE
PERFORMANCE OR USE OF THIS MANUAL.

The information in this user’s manual is protected by copyright laws. No part of this
manual may be photocopied or reproduced in any form without prior written
authorization from the copyright owners.

Copyright May, 2005
All rights reserved.

Microsoft and Windows are registered trademarks of Microsoft Corporation. DOS,
Windows 95/98/ME/2000/NT/XP are trademarks of Microsoft Corporation.

Product names mentioned herein may be trademarks and/or registered trademarks
of their respective owners/companies.

The software described in this manual is delivered under a license agreement. The
software may be used or copied only in accordance with the terms of the agreement.

This product incorporates copyright protection technology that is protected by U.S.
patents and other intellectual property rights. Use of this copyright protection
technology must be authorized by Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
.

Rev 1.0

i -2

TABLE OF CONTENTS

PREFACE

Symbols and Conventions
Protecting Your Computer - Avoid Abusive Handling and Adverse
Environment
Chapter Summaries

1. GETTING TO KNOW THE BASICS

Performance Features (1-2,3)
System at a Glance (1-4)

Top View (1-4,5,6,7)
Front and Rear Views (1-8,9)
Side Views (1-10,11)
Bottom View (1-12,13)
AC Adapter (1-14)
LED Status Indicators (1-15)

Keyboard Features (1-16)

Function (Quick) Keys (1-16)
Windows Keys (1-17)

Embedded Numeric Keypad (1-17)
Touch Pad (1-18)
Graphic Subsystem (1-19)

Adjusting the Display Brightness (1-19)

Extending the Life of the TFT Display Panel (1-19)

Opening and Closing the Display Panel (1-20)
Audio Subsystem (1-21)

Adjusting the Volume in Windows (1-21)

Voice Recording (1-21)
Modem and Modem Setting (1-22)
Ethernet Adapter (1-23)

2. BIOS SETUP AND SECURITY

Entering the BIOS Setup Screen (2-3)
Leaving the BIOS Setup Screen (2-3)
BIOS Action Keys (2-3)

i -3

Modifying the BIOS Settings (2-4)

Main Setup (2-4)

Advance Setup (2-4,5)

Security Setup (2-5,6)

Power Setup (2-6,7)

Boot Setup (2-7,8)

Exit Setup (2-8)

3. BATTERY POWER & POWER MANAGEMENT

The Battery Pack (3-2)

Lithium-Ion Battery Technology (3-2)

Battery Low-Power Warning (3-3)
Installing and Removing the Battery Pack (3-4,5)
Charging the Battery and Charging Time (3-5)
Checking the Battery Level (3-6)
Prolonging the Battery’s Life and Usage Cycles (3-6)
Using Windows Power Options (3-7)

Windows’ Power Schemes (3-7,8)

Suspend Modes (3-9,10)

Power Button Action (3-11)

Low Battery Warning (3-12)

Power Manual Quick Access (3-13)

4. UPGRADING YOUR COMPUTER

Upgrading the Hard Disk Drive (4-2,3,4,5)
Upgrading the System Memory (4-6,7,8,9,10)
Installing a Mini PCI Card to the System (4-11,12,13)

5. TROUBLE-SHOOTING2

First Step (5-2,3)
Audio Problems (5-4)
Hard Disk Problems (5-5,6)
Optical Drive Problems (5-7)
Display Problems (5-8)
Keyboard and Mouse Problems (5-9)
CMOS Battery Problems (5-10)
Memory Problems (5-11)

i -4

Modem Problems (5-12)
Network Adapter / Ethernet Problems (5-13)
PC Card / PCMCIA Problems (5-14)
Performance Problems (5-15)
Firewire (IEEE1394) and USB2.0 Problems (5-16)

APPENDIX A Product Specification
APPENDIX B Agency Regulatory Notices

i -5

Preface

Using This Manual

This User’s Manual contains general information about the
hardware and software setup, troubleshooting, and technical
specifications of the notebook computer.

Symbols and Conventions

The following conventions and symbols are used in this manual:

 When keys are to be pressed at the same time, a plus (+)

symbol is used. For instance, Fn+F7 means holding Fn and
F7 keys at the same time.

 When a series of clicking actions is needed in Windows O/S, [ ]

and > symbols are used. For instance, [Start > Settings >
Control Panel > Display] means clicking the Start icon first,
then the Settings, then the Control Panel, then the Display
icon.

 When you need to make a selection with the touch pad (or

mouse), you will be asked to ’select’ or ‘click’ or ‘double-click’,
‘right-click’ the item.

Note:

Text in this format and symbol means specific instructions, commentary ,

sidelights, or any additional information or notes that you should be aware of.

Warning:

given instructions or information could result in damage to your computer or could
cause bodily harm or loss of life.

Text in this format and symbol means that failures to comply with the

i -6

Protecting Your Computer - Avoid Abusive Handling and
Adverse Environment

Follow the advice below will help ensure that you get the most out
of your Investment.

Your computer will serve you well if you take good care of it.
 Do not expose the computer to direct sunlight or place it near
sources of heat.
 Do not subject it to temperatures below 0

o

30

C (86oF).

o

C (32oF) or above

 Do not expose the computer to magnetic fields.
 Do not expose the computer to moisture or rain.
 Do not spill water or liquid on the computer.
 Do not subject the computer to adverse shock and vibration.
 Do not expose the computer to dust and dirt.
 Do not place objects on top of the computer to avoid damaging

the computer.
 Do not place the computer on rocky surfaces.

Here are some ways of taking care of your AC adapter.
 Do not connect the adapter to any devices other than your
computer.

 Do not let water get into the adapter .
 Do not block the ventilation airway of the adapter.
 Keep the adapter in a cool and ventilated place.
 Do not step on the power cord or place heavy objects on top of

it.
 Carefully tuck away the power cord and any cables away from
pedestrian traffic.
 When unplugging the power cord, do not pull on the cord itself
but pull on the plug.

i -7

 Keep the adapter away from children.
 The total ampere ratings of the equipment plugged in should

not exceed the ampere rating of the cord if you are using an
extension cord.
 The total current rating of all equipment plugged into a single
wall outlet should not exceed the fuse rating.
 Do not connect other A C a dapter to your notebook. This
Notebook uses exclusively the AC adapter:

Liteon PA-1650-02 (65W), Electricity Power Source F10654-A (65W)

Lishin 0335A2065 (65W),

When cleaning the computer, observe these steps:

1. Power off the computer and remove the battery pack.

2. Disconnect the AC adapter.

3. Use a soft cloth dampened with water. Do not use liquid or
aerosol cleaners.

Contact your dealer or see your service technician if any of the
following occurs:

 Computer has been dropped or the body has been damaged.
 Liquid has been spilled into the product.
 The computer does not operate normally.

Cleaning the Ventilation Grills:
It is suggested that you clean the ventilation grills regularly to
maintain optimal thermal regulation of the notebook. To do this, you
may use a soft brush or a vacuum cleaner (with appropriate head
adapter) to remove the dust buildup on the ventilation grills.

i -8

Chapter Summaries

The following is a summary of the available chapters and
appendices in this manual.

Chapter 1: Getting to Know the Basics
In this chapter, you will learn the basic operations and features
of your computer. It gives you a gene ral understanding of the
components of your computer.

Chapter 2: BIOS Setup / Security
In this chapter, you will learn how to cha nge various firmware
settings and what the settings mean. Also, you will learn how to
take advantage of the built-in security feature provided by the
BIOS.

Chapter 3: Battery Power & Power Management
In this chapter, you will learn the fundamentals of power
management and how to use them to achieve longer battery life.

Chapter 4: Upgrading Your Computer
In this chapter, you will learn how to up grade the system
memory, the hard disk drive, and to install wireless mini PCI card.

Chapter 5: Trouble -Shooting
In this chapter, you will learn how to solve common hardware
and software problems.

Appendix A: Product Specification
In this section, you will find a list of the computer’s system
specifications.

Appendix B: Agency Regulatory Notices
In this section, you will find the general electro-magnetic and
safety regulatory information.

i -9

■ chapter 1 getting to know the basics

CHAPTER▼ ONE

GETTING TO KNOW THE BASICS

This chapter introduces the features and
components of the computer.

1-1

■ chapter 1 getting to know the basics

Performance Features

 High Performance Processor with Alvi so Chipset

The notebook PC is equipped with a powerful Mobile Intel
Pentium M or Celeron M processor . Together with the latest
Alviso chipset and technologies, the system offers
advanced PC performances.

 Advanced Graphic Engine

The Intel Integrated GMA900 Extreme3 video processor
gives excellent graphic performance. The advanced
graphic chip also incorporates a hardware-based
motion-compensation engine, which gives you smooth
MPEG video playback. 3D graphics capability also adds
realism to PC games.

 LCD Display

The computer is equipped with a 15” or wide 15.4” TFT
high-resolution display panel for clear text and brilliant
colors.

 Serial ATA Hard Disk Drive Support (on certain models)

The serial ATA bus offers higher data throughput than the
traditional parallel ATA bus. This gives you optimal hard
drive performance.

 Expandability

The system offers upgradeable hard disk drive and 2 DDR
SDRAM sockets for expansion, allowing the user to easily
increase the storage and system capacities as the need
arises.

 Built-in Multiple Card Reader

1-2

■ chapter 1 getting to know the basics

The built-in 4-in-1 card reader lets you access many of the
portable media formats (SD Card, MMC Card, MS Card,
and MS Pro Card).

 Ethernet Port

The system provides built-in 10/100Mbps or
10/100/1000Mbps Ethernet network adapter for high
bandwidth network connection.

 Firewire (IEEE1394 / 1394a) and USB2.0 ports

In addition to a full array of built-in I/O por

ts, the computer

offers IEEE1394 for ultra high-speed connection to high
bandwidth digital video devices and US B2.0 ports to
connect to any USB-based peripheral devices.

 Wireless LAN

The internal Wireless LAN module allows your notebook to
connect wirelessly to other 802.11-enabled systems,
devices, or network.

 Internal USB slot for integrated USB Devices (Optional)

The optional USB Bluetooth module or USB Thumb Drive
gives you added function to the notebook.

1-3

■ chapter 1 getting to know the basics

System At A Glance

Top View

1. LCD Latch

The LCD latches lock / unlock the LCD panel.

2. Built-in Microphone

The built-in microphone records sound.

1-4

■ chapter 1 getting to know the basics

3. LCD Display

The panel is where the system content is displayed.
The LCD panel has a maximum opening of 135 degrees. Do
not push it down forcibly.

4. Built-in Stereo Speakers

The built-in speakers output the sound in stereo.

5. Keyboard

The keyboard is used to enter data. It has an embedded
numeric keypad and cursor control keys. (See Keyboard
Section for details.)

6. Touch Pad

The touch pad is a built-in pointing device with functions similar
to a mouse.

7. LED Status Indicator

The LED Status indicators reveal the status of these functions:
Numeric keypad, cap lock, scroll lock, WLAN module enabling
and disabling and also the ODD, HDD activities. (See the LED
Status Indicator Section for details.)
The LED Status indicators also reveal the status of the system

1-5

■ chapter 1 getting to know the basics

power state and battery-charging state. See the LED Status
Indicator Section for details.

8. Power / Suspend Button

The power/suspend button turns the notebook on and off and it
also acts as a system suspend key. Press momentarily to turn
on the system. Press and hold for at least 4 seconds to turn off
the system. How this key behaves can be defined in [Start >
Settings > Control Panel > Power Options > Advanced] menu.
Press the power / suspend button again to return from the
suspend mode. (See Chapter 3 for more details on system
suspend function.)

Note:

When the system power is initially turned on, the Scroll-lock,
Cap-lock, and Numeric keypad LED indicators will light up momentarily to
indicate the start of the Power-On sequence.

9. Silent Mode Button

Pressing the key enables the system to lower its power usage;
therefore the fan speed is reduced to achieve lowest operating
noise.

10. Instant-On Multimedia Player Launch Key

When the system is powered off, pressing the key launches a
multimedia application that allows you to watch movies files,
listen to music, or view photos in the optical drive or hard disk
drive without having to boot to Windows.

Note:

The way the Instant-On software works is that when the quick key is

1-6

■ chapter 1 getting to know the basics

pressed (when the system is in Power-Off mode), the system boots to a
Linux-based O/S and media player application.

11. Internet Explorer Quick Key

Pressing the button launches Internet Explorer in Windows.

1-7

■ chapter 1 getting to know the basics

Front and Rear View

Warning: Do not place any heavy objects on the top of notebook. This may

damage the display

1. External VGA Port

The 15-pin VGA analog port is for connecting the external CRT
monitor or projector.

2. Battery Pack

The battery pack is a built-in power source for the notebook.

3. Kensington Lock Key Hole

A Kensington -type se curity lock latches to this keyhole for
anti-theft purpose.

4. 4-in-1 Card Reader

The 4-in-1 Card Reader supports SD Card, MS Card, MMC
Card, and MS-Pro Card.

5. Microphone Jack

The microphone jack (3.5-mm diameter) is where you connect
a microphone.

1-8

■ chapter 1 getting to know the basics

6. Audio Line-in Jack

The Audio Line-in jack (3.5-mm diameter ) is where yo u connect
an external audio input source such as a CD Player.

7. Stereo Headphone / SPDIF-out Jack

The stereo headphone jack (3.5-mm diameter) is where you
connect the headphones or external speakers. Alternatively,
you may connect the SPDIF output to an external DTS, AC3, or
PCM sound processor / decoder in your home stereo system.

8. Wireless On/Off Switch

Use the Switch to disable or enable Wireless function.

1-9

■ chapter 1 getting to know the basics

Side Views

Warning:

damage the display

Do not place any heavy objects on the top of notebook. This may

1. Ethernet / LAN Port

The port connects to a network hub via the RJ-45 cable and
also conforms to 10/100Base-TX transmission protocol.

2. Modem Port

This is where you plug the phone jack (RJ-11) for fax/modem
functions.

3. Optical Drive and Disk Eject Button and Manual Eject Key
Hole

If your computer comes with the Combo drive, DVD-RW,
DVD+RW, or DVD-Dual drive, you may save data onto a CD-R
/ CD-RW or DVD RW disc. Press the eject button to eject the
disk tray. The manual eject keyhole allows you to manually
eject a jammed disk.

1-10

■ chapter 1 getting to know the basics

4. PC Card Slot (Type II PCMCIA) and Card Eject Button

The slot is where PC Card (Type II PCMCIA) is inserted. Press
the eject button to release the PC Card.

5. Ventilation Grill

The fan grill is where air is exchanged to dissipate the internal
heat. Do not block this airway completely.

6. Firewire / IEEE1394 / 1394a Port

This is a high-speed serial data port. You may connect any
Fire-wire-ready device to this port.

7. USB2.0 Port (x3)

The Universal Serial Bus (USB2.0-compliant) port allows you to

connect a wide variety of devices to your computer at a rate of
up to 480 Mbps. This port conforms to the latest USB2.0
plug-and-play standards.

8. Power Jack (DC-in)

The DC-out jack of the AC Adapter connects here and powers
the computer.

9. TV (S-Video) Port

The S-Video port permits you to redirect the screen output to a
television set or any analog video playback device. This TV
Port is copyright protected; when DVD movie is played, the
output is scrambled to prevent analog recording.

1-11

■ chapter 1 getting to know the basics

Bottom View

1. Battery Pack and Battery Latch

The battery pack is a built-in power source for the notebook.
Slide the battery latch to release the battery pack.

1-12

■ chapter 1 getting to know the basics

2. USB Device Cover (Optional)

Underneath the cover , there is a USB connector. You may
install the optional Bluetooth module or USB Thumb Drive into
this slot.

3. Hard Disk Drive Cover

The system’s hard disk drive is located unde r the cover. The
HDD can be upgraded to a larger capacity. (See Chapter 4 for
instructions on a HDD upgrade.)

4. System Device Cover

The system’s processor with cooler assembly, Wireless LAN
module, and DDR memory module are located under the case
cover. You may install the WLAN module and the sy stem
memory can be upgraded to a larger capacity. (See Chapter 4
for instructions on a memory upgrade.)

5. Ventilation Grill

The fan grill is where air is exchanged to dissipate the internal
heat. Do not block this airway completely.

Warning:

surface only. The bottom case may get very hot.

Do not block the Fan Grill outlet. Place the machine on hard

1-13

■ chapter 1 getting to know the basics

AC Adapter

1. DC-out Connector

The DC-out connector docks to the power jack (DC-in) on the
computer.

2. Adapter

The adapter converts alternating current into constant DC
voltage for the computer.

3. AC Plug

The AC plug plugs to the AC wall outlet.

Warning: Make sure you are using a standard 3-prong AC wall socket with a

ground pin. If not, you may feel a slight tingling sensation on any of the
computer’s metal parts such as the I/O ports. This is caused by leakage current
when the AC adapter is not properly grounded (via the ground pin). However,
the amount of leakage current is within the safety regulation and is not harmful
to human body.

1-14

■ chapter 1 getting to know the basics

LED Status Indicator

The LED Status Indicator displays the operating status of your
notebook. When a certain function is enabled, an LED will light
up. The following section describes its indication.

System & Power Statu s Indicators

LED Graphic

Symbol

Indication

Green light indicates the WLAN module
is active.

Blinking green light indicates the
notebook is in suspend mode.

Persistent green light indicates the Silent
mode is active.

Blinking orange light indicates the
battery is being charged.

Blinking red light indicates the battery
power is low when the system is turned
ON.

Persistent green light indicates the
battery is Full.

Green light indicates the hard drive

Note:

When the system power is initially turned on, the Scroll-lock, Cap-lock,
and Numeric keypad LED indicators will light up momentarily to indicate the
start of the Power-On sequence.

and/or optical drive is being accessed.
Green light indicates the numeric keypad

is activated.
Green light indicates the cap-lock is

activated.
Green light indicates the scroll-lock is

activated.

1-15

■ chapter 1 getting to know the basics

Keyboard Features

Function Keys (Quick Keys)

Graphic

Symbol

For various system controls, press the Fn (Function) key and the Fx key
simultaneously.

Action System Control

Fn + F1 Enters Suspend Mode.

Fn + F3 Audio Mute on or off.

Fn + F4 Changes Display Mode:

Fn + F5 Turns Speaker Volume up.
Fn + F6 Turns Speaker Volume down.

Fn + F7 Increases Display Brightness.
Fn + F8 Decreases Display Brightness.

Fn+Num Lk Enables the embedded keypad

Fn + Scr Lk Press the Scroll Lock key and

LCD-only, CRT-only and
LCD&CRT.

to work in numeric mode. The
keys act like numeric keypads
in a calculator . Use this mode
when you need to do a lot of
numeric data entry. An
alternative would be to connect
an external numeric keypad.

then press ↑or ↓to move one
line up or down.

1-16

■ chapter 1 getting to know the basics

Windows Keys

Your keyboard also has two Windows keys:

1. Start Key
This key allows you to pull up the Windows Start Menu at
the bottom of the taskbar.

2. Application Menu Key
This key brings up the popup menu for the application,

similar to a click of the right mouse button.

Embedded Numeric Keypad

Press Fn+NumLk to enable the embedded numeric keypad.
The numbers are printed in upper right corner of a key, in a
color different from the alphabets. This key pad is complete
with arithmetic operators (+, -, * , /).

Press Fn+NumLk to revert to normal character keys.

1-17

■ chapter 1 getting to know the basics

Touch Pad

The built-in touch pad, which is a PS/2-compatible pointing device,
senses movement on its surface. As you move your fingertip on the
surface of the pad, the cursor responds accordingly.

The following items teach you how to use the touch pad:

1. Move your finger across the touch pad to move the cursor.

2. Press buttons to select or execute functions. These two buttons
are similar to the left and right buttons on a mouse. Tapping on the
touch pad twice produces is similar to clicking the left button of a
mouse.

Function Left Button Right

Button

Execution Click twice

quickly

Selection Click once Tap once
Drag Click and hold

to drag the

cursor
Access
Context Menu
Move One
Page Up or
Down

Click once

Tap twice (at the same speed as

Tap twice quickly and on the

Tips on Using the Touch Pad:

1. The double-click speed is timed. If you double-click too slowly,
your notebook responds as if you single-clicked twice.

2. Keep your fingers dry and clean when using the touch pad.
Also keep the surface of touch pad clean and dry to prolong its life.

3. The touch pad is sensitive to finger movements. Hence, the
lighter the touch, the better the response. Heavy touch does not
produce better response.

Equivalent Tapping Action

double-clicking
the mouse button)

second tap hold finger to the touch
pad to drag the cursor

1-18

■ chapter 1 getting to know the basics

Graphic Subsystem

Your computer uses a high performance 15-in ch or 15.4-in ch (wide)
active matrix TFT panel with high resolution and multi-million colors
for comfortable viewing. The Intel Integrated GMA900 Extreme3
video graphics accelerator , whi ch is Microsof t DirectX 9 compatible,
performs graphic rendering at a lighting-fast speed.

Adjusting the Display Brightness

The notebook uses special key combinations, called hot keys,
to control brightness.
Press Fn+F7 to increase the brightness.
Press Fn+F8 to decrease the brightness.

Note: To maximize your battery operating time, set the brightness to the

lowest comfortable setting, so that the internal backlight uses less power.

Extending the Life of the TFT Display Device

Observe the following guidelines to maximize the life of the
backlight in the display.

1. Set the brightness to the lowest comfortable setting
(Fn+F8).

2. When working at your desk, connect your notebook to an
external monitor and disable the internal display Fn+ F4.

3. Do not disable the suspend time-outs.

4. If you are using AC power and have no external monitor
attached, change to suspend mode when not in use.

1-19

■ chapter 1 getting to know the basics

Opening and Closing the Display Panel

To open the display, push the LCD latch inwardly and lift up the
lid. Then tilt it to a comfortable viewing position. The LCD panel
has a maximum opening of 135 degrees. Do not push it down
forcibly.

1-20

To close the display cover, fold it down gently until the LCD
latches click into place.

Warning:

place any object on top of the computer when the display is closed

To avoid damaging the display, do not slam it when closing. Do not

■ chapter 1 getting to know the basics

Audio Subsystem

Your computer’s audio subsystem is Sound Blaster Pro-compatible.

Adjusting the Volume Manually

To increase the volume, press Fn+ F5.
To decrease the volume, press Fn+F6.

Adjusting the Audio Volume in Windows

1. Click the speaker symbol in the task tray in Windows.

2. Drag the volume control bar up or down to adjust the volume.

3. To temporarily silence the speaker without changing the
volume setting, click Mute.

Voice Recording

A built-in micropho ne allows you to record sound. You will need
to use audio processing software to enable the built-in
microphone. For example, you may use Microsoft Sound
Recorder.

1-21

■ chapter 1 getting to know the basics

Modem

Y our comp uter comes with a 56K V.92 internal fax/modem and a phone
jack (RJ-1 1), which is located on the lef t side of your computer.
Use a telephone cable to connect the computer to the telephone wall
outlet.

Connecting the Modem

1. Plug one end of the phone line into the modem port located on
the rear side of the computer . (For EMI compliance, you need to clip
the included EMI CORE to the phone line.)

2. Plug the other end of the line into the analog phone wall outlet.

Depending on where your computer is used, you may need to change
settings in the modem. Correct setting will allow you to maintain a stable
connection in a country where its telecommunication system may be
different to others.

T o change the modem setting, do the follo wing:

1. Go to [S tart > Settings > Control Panel] and doubl e-click on
Modem Settings icon. You will see a similar dialog box.

1-22

2. Click on the pull-down menu and select the country where it is
applicable. Click on OK to exit.

■ chapter 1 getting to know the basics

Ethernet

Your computer is equipped with a 10/100Base-TX or
10/100/1000Base-TX Fast Ethernet network adapter. Connect the
active LAN cable to the RJ-45 LAN port located on the left side of
the computer. This allows you to access and transmit data in the
local area network.

Connecting to the Network

Use Unshielded Twisted Pair (UTP) Ethernet cable only.

1. Insert one end of the UTP cable into the network connector
until the connector snaps securely into the receptacle.

2. Either connect the other end of the cable to an RJ-45 jack
wall outlet or to an RJ-45 port on a UTP concentrator or hub in
the network.

Cabling Restriction for Networks

The following restrictions should be observed for
10/100/1000BASE-TX networks:
 The maximum cable run length is 100 meters(m) (328
feet[ft]).
 For 100Mbps or 1000Mbps operations, use Category 5
wiring and connections.

Note:

Consult Windows manual and / or Novell Netware user’s guide for the

software installation, configuration, operation of the network.

1-23

■ chapter 2 bios setup and security feature

CHAPTER▼ TWO

BIOS SETUP AND SECURITY FEATURE

In this chapter, you will learn how to
enter the BIOS Setup Menu and
manipulate various hardware control
settings. You will also learn how to use
the built-in security features.

2-1

■ chapter 2 bios setup and security feature

The Setup Utility is a hardware configuration program built into

your computer’s BIOS (Basic Input/Output System). It runs and

maintains a variety of hardware functions. It is a menu-driven

software, which allows you to easily configure and change the

settings.

The BIOS contains manufacture’s default settings for the

computer’s standard operations. However, there are occasions

when you may be required to modify the default settings in the

BIOS. For example, you may need to configure the BIOS power

management (APM) settings if you are using DOS, or

non-Windows operating system.

The BIOS allows you to set up passwords to limit access to users.

This is an important feature because a great deal of vital

information is carried within the computer nowadays. Unauthorized

access can be prevented. Later in this chapter, you will learn how to

use this security feature.

2-2

■ chapter 2 bios setup and security feature

Entering the BIOS Setup Screen

First turn on the power. When the BIOS performs the POST
(Power-On Self Test), press F2 key quickly to activate the AMI
BIOS Setup Utility.

Note:

You may need to press F2 key fairly quickly. Once the system begins to load

Windows, you may have to retry by cycle-power on again

Leaving the BIOS Setup Screen

When you have finished modifying the BIOS settings, exit the BIOS.
It takes a few seconds to record changes in the CMOS.

BIOS Action Keys

Function Key Command Description

Leaves a sub-menu to return to the

ESC Exit

previous menu OR exits the BIOS setup
while saving changes.

Enter Go to Sub Screen Shows the Sub Menu

F1 General Help Shows the Help Screen

F10 Save and Exit

<Tab> Select a field Selects the next field.

↑ Select an item Selects the next upper item.
↓ Select an item Selects the next lower item.

- Lower value Selects the next value within a field.

+ Higher value Selects the next value within a field.

Saves changes and reboots the
computer.

2-3

■ chapter 2 bios setup and security feature

Modifying the BIOS Settings

The AMIBIOS setup main menu is subdivided into sub-menus.
Each menu item is described in this section.

Main Setup

Under this menu, you may change time/date and view basic
processor and system memory information.

Item Selections /

Sub-menu

Date N/A Type in the current date, in MM/DD/YY

Time N/A Type in the current date, in HH:MM:SS

Description

format.

format.

Advanced Setup

►IDE Configuration

Item Selections /

Sub-menu

Primary
IDE
Master
Secondary
IDE
Master

Hard Disk Primary Master is where BIOS tries to

ATAPI CDROM The secondary master controls the

Description

boot from first. The primary master
controls the hard drive.

ATAPI CD-ROM drive.

2-4

Note:

The sub-menu is not selectable. Press enter to view information of the

■ chapter 2 bios setup and security feature

storage device.

Item Selections /

Description

Sub-menu

TouchPad
Support

LCD Auto
DIMM
Function

Enabled
Disabled

Enable
Disable

Enable or disable the built-in touchpad.

[Enable]: The system automatically
reduces the LCD brightness when AC
power is removed to save power.
[Disable]: The LCD brightness remains
the same whether or not AC power is

present.
BIOS Post
Beep
Sound

Enable
Disable

[Enable]: The system beeps when

performing POST on boot.

[Disable]: The beep is disabled.

Security Setup

►Boot Settings Configuration

Item Selections /

Sub-menu

Change

N/A Install or Change the Password
Supervisor
Password
Change

N/A Install or Change the Password
User
Password

Description

Using Password Protection

Two Levels of Password Protection are available. The BIOS

2-5

■ chapter 2 bios setup and security feature

provides both a Supervisor and a User password. If you try to
activate both passwords, the Supervisor password must be set first.
The passwords activate two different levels of protection:

1. System always asks for password every time it is powered on.

2. System asks for password only when you attempt to enter
BIOS utility.
The passwords are encrypted and stored in NVRAM. Make sure
you write them down or memorize them. If you lost the passwords,
the computer may need to be sent back to the factory or to an
authorized service dealer to reset the passwords.

Power Setup

Item Selections /

Sub-menu

Power Button
Mode

High
Performance

On/Off
Suspend

Enable
Disable

Mode

Long Battery
Life Mode

Enable
Disable

Description

[On/Off]: When the power button is
pressed, the system is turned off.

[Suspend]: When the power button is
pressed, the system enters the suspend
mode.

When Enabled, maximum system
performance can be achieved. The
processor performance is enhanced.

When Enabled, maximum battery life
can be achieved. The processor
performance is lowered.

Note:

The Suspend Mode selection in BIOS only applies to older Windows version

(such as Windows 3.1 or Windows 95 or NT4) or non-Windows operating system. In

2-6

■ chapter 2 bios setup and security feature

Windows ME / 98SE / 2000 / XP, suspend mode and settings are determined by

settings in the Power Options Properties (Start > Control Panel > Power Options).

Boot Setup

►Boot Settings Configuration

Item Selections /

Sub-menu

Quiet Boot Disabled

Enabled

►Boot Device Priority

Item Selections /

Sub-menu

1st Boot
Device

Removable Dev.

CD/DVD

Hard Drive

Realtek Boot

Agent

Disabled

2nd Boot
Device

3rd Boot
Device

4th Boot
Device

Description

When Enabled, the system will display
OEM logo instead of the POST
messages.
When Disabled, the system will display
POST messages (i.e. devices
information.)

Description

Set the type of device for the 1st drive
BIOS attempts to boot from. If Realtek
Boot Agent is selected, system will
attempt to load boot sector from the
Ethernet port.

Set the type of device for the 2nd drive
BIOS attempts to boot from.

Set the type of device for the 3rd drive
BIOS attempts to boot from.

Set the type of device for the 4th drive
BIOS attempts to boot from.

2-7

■ chapter 2 bios setup and security feature

Note:

If you select Realtek Boot Agent, the system will attempt to boot from the

network.

Note: When the BIOS performs POST, you may also press F12 Key to enable the

Boot Device selection menu. You may choose CD/DVD, Hard Drive, or Realtek Boot

Agent as the first storage device to boot from. If you have already connected a USB

Floppy Disk Drive before powering up, it will appear as a Removable Device in the

Boot Device selection menu

Exit Setup

Item Selections /

Sub-menu

Saves

N/A After you have completed the BIOS
Changes and
Exit

Discard

N/A Discards changes done so far to any of
Changes and
Exit

Discard

N/A Discards changes done so far to any of
Changes

Load Optimal

N/A Load Optimal Default value for all the
Defaults

Description

settings, select this item to save all
settings, exit BIOS Setup utility, and
reboot. New system settings will take
effect on next power-up. F10 key can be
used for this operation.

the setup questions and exit.

the setup questions.

setup questions. F9 key can be used for
this operation.

2-8

■ chapter 3 battery power & power management

CHAPTER▼ THREE

BATTERY POWER & POWER

MANAGEMENT

In this chapter, you will learn the
fundamentals of power management
and how to use it to achieve longer
battery life.

3-1

■ chapter 3 battery power & power management

In this chapter, you will learn how to operate your notebook on

battery power, how to handle and maintain the battery pack, and
learn about the system’s power saving features.

TFT display, central processor, hard disk drive are the major
hardware subsystems that consume the most power. Power
management deals how these key components should behave to
conserve power . For example, you can have the system turn off its
display after 2 minutes of inactivity to save power. Efficient power
management can help you work longer sessions before having to
recharge the battery.

The Battery Pack

Lithium-Ion Battery

Your notebook uses a six-cell or nine-cell (optional)
Lithium-Ion battery pack that provides power when you
don’t have access to an AC outlet.

3-2

Note:

It is necessary that you charge the battery pack for at least 6

hours before using it for the first time.

Note: In the Standby Suspend mode, a fully charged battery loses its

power in roughly 1/2 day or less. When not being used, the battery’s
power will deplete in 1-2 month.

■ chapter 3 battery power & power management

Battery Low-Power Warning

1. Low Battery Warning
Low battery condition occurs when battery power is
reduced to 6%. The red battery status LED indicator
blinks and the system beeps once every 16 seconds or
so.

2. Very Low Battery Warning
Very Low battery condition occurs at 3 % power
remaining. The red battery status LED indicator blinks
and the system beeps at 4-second interval.

When the notebook warns you of its low battery condit ion,
you will have about 3-5 minutes to save your current
work.

Warning:

degree Celsius (32 degree F) or above 60 degree C (140F). This may
adversely affect the battery pack.

Do not expose battery packs to temperatures below 0

Press Fn+F3 to turn off the battery warning beep.

Note:

3-3

■ chapter 3 battery power & power management

Installing and Removing the Battery Pack

To Remove the Battery Pack:

1. Place the notebook bottom-side up on a flat and
secured surface.

2. Push the latch and pull the battery’s hard case
away from the notebook.

3-4

■ chapter 3 battery power & power management

To Install the Battery Pack:

1. Place the notebook bottom-side up on a flat and
secured surface.

2. Carefully insert the battery pack into the battery
compartment of the notebook.

Charging the Battery and Charging Time

To charge the battery, while the battery pack is in the noteboo k,
plug the AC adapter into the notebook and an electrical outlet.
The charging time is approximately 4-6 hours when the
notebook is turned off and approximately 6-10 hours when the
notebook is turned on.
When the battery is fully charged, the battery charge indicator
becomes green.

If system runs at heavy loading or in a high temperature environment,

Note:

the battery may not be fully charged. You need to continue to charge it with the
AC adapter plugged in until the charging LED turns green.

3-5

■ chapter 3 battery power & power management

Checking the Battery Level

You can check the remaining battery power in the Windo ws
battery status indicator, which is located at the lower right-hand
corner of the task bar. (If you do not see a battery or AC-in icon
on the task tray, go to Power Options Properties box and click
on the Advanced tab. Check off ``Always show icon on the task
bar``.)
Alternatively, you can access the power meter by clicking the
Power Options icon in the Windows Control Panel.

Prolonging the Battery’s Life and Usage Cycles

There are ways you can do to prolong the use of battery.
 Use the AC adapter wherever AC wall outlet is available.

This will ensure uninterrupted computing.

 Purchase additional battery pack.
 Store the battery pack in room temperature. Higher

temperature tends to deplete the battery’s power faster.
 Make good use of the power management function. Save
To Disk (Hibernate) saves the most energy by storing current
system contents in a hard disk space reserved for this function.
 The life expectancy of the battery is app roximately 300
recharges.
 See the notices section in the beginning of the user
manual on how to care for the battery pack.

Note:

Read Section Protecting Your Notebook in the beginning of this manual

for tips about how to maintain the battery pack.

Note: To achieve optimal battery performance, you may need to do a battery

calibration at a 3-month interval. To do this:

1. Fully charge the battery.

2. Then discharge the battery by entering the BIOS setup screen. (Press F2
key as soon as you turn on the computer. And let it remain at the setup screen
until the battery runs out.

3. Fully charge the battery again.

3-6

■ chapter 3 battery power & power management

Using Windows Power Options

Windows Power Management provides basic power saving
features. In the Windows Power Options Properties [Start >
Settings > Control Panel > Power Options] dialogue box, you
may enter time-out values for display and hard disk drive.
Windows power manager saves power by turning off hard drive
after 1 minute of inactivity, for example.

Windows’ Power Schemes

The power management control panel in Windows XP,
known as Power Schemes, is designed to provide the
user with an easy-to-use interface. The Power Schemes
tab can be found in the Power Options Properties panel
that is accessible via the control panel window.
Schemes are easy to understand, based on notebook
usage scenarios, and control not only processor power
usage but other system peripherals as well.
Go to [Start > Settings > Control Pan el] and double-click
the Power Options icon.

Always on mode puts the processor into maximum
performance mode, which provides no power saving.
The other schemes control processor performance
based on demand. For example, Max Battery mode
lowers the processor’s speed and voltage to conserve
power as much as possible.

3-7

■ chapter 3 battery power & power management

In this dialog box, you can manually set the LCD and
hard drive’s time-out values in the Plugged in colu mn and
in the Running on batteries column. Lower time-out
values will save more battery power.

3-8

Note:

Also consult Windows user guide for more information on how

to use Windows power management functions.

Note: Actual dialogue box shown above may appear slightly different.

■ chapter 3 battery power & power management

Suspend Mode

Standby Suspend

The system automatically enters this mode after a period
of inactivity, which is set in the Power Schemes dialog
box. In Standby mode, hardwa re devices, such as
display panel and hard disk, are turned off to conse rve
energy.

Hibernate Suspend

In this mode, all system data are saved in the hard disk
before powering down. When this mode is activated, all
system state and contents are saved to the hard disk
drive after a period of inactivity defined by the user. No
power or very little power is drawn from the battery
module under this mode.
However, depending on how much RAM that have been
installed on your computer, the amount of time the
system requires to restore all its previous contents can
range from 5 to 20 seconds.
For Windows 2000 / XP users, hibernation is handled by
the operating system; therefore, no special disk partition
or disk file is necessary.
If you wish to activate Hibernate mode, you need enable
Hibernate Support in the Hibernate tab of the Power
Options menu.

3-9

■ chapter 3 battery power & power management

3-10

Note:

Do not install or remove the memory module when the system

is in the suspend mode.

Note: Actual dialogue box shown above may appear slightly different.

■ chapter 3 battery power & power management

Power Button Action

The notebook PC’s power button can be set to turn of f
the system or activate the suspend mode.

Go to [Start > Settings > Control Panel > Power Options]
and click on the Advanced tab. In the pull-down menu,
select how you wish the power button to work as.

Note:

Actual dialogue box shown above may appear slightly different.

Warning:

pull-down menu, DO NOT select Do nothing – otherwise the system will
still run at high speed while the processor’s fan grill is fully blocked by
the closed LCD panel. The heat will damage the LCD panel.

In the When I close the lid of my portable computer

3-11

■ chapter 3 battery power & power management

Low Battery Warning

You can define when and how the system warns you of
its battery-low condition.

Go to the Alarms tab in th e Power Options Properties box.
If you wish to hear audible beeps, click on the Alarm
Action button and put a check on Sound Alarm.

3-12

Note:

Consult Windows user guide for more information on how to

use Windows power management functions.

Note: Actual dialogue box shown above may appear slightly different.

■ chapter 3 battery power & power management

Power Manu Quick Access

Instead of making specific selections in the Power
Options Properties box, you can quickly and easily
specify which pre-set power saving function you desire
by clicking on the Battery icon at the lower right-hand
corner of the task bar. (If you do not see a battery or
AC-in icon, go to Power Options Properties box and click
on the Advanced tab. Check off ``Always show icon on
the task bar``.) Select Max Battery if you want the system
to enter suspend mode more often. Or, select Always On
if your notebook PC is plugged into an AC power source.

Actual dialogue box shown above may appear slightly different.

Note:

3-13

■ chapter 4 upgrading your computer

CHAPTER▼ FOUR

UPGRADING YOUR COMPUTER

In this chapter, you will learn how to
upgrade the DRAM, hard disk drive, and
to install the optional wireless LAN mini
PCI.

4-1

■ chapter 4 upgrading your computer

Upgrading the Hard Disk Drive

Replacing the original drive with one of larger capacity can in crease
the hard drive capacity of your computer. Depending on the model,
the computer may use 9.5 mm (height), 2.5-inch Ultra ATA type
hard disk drive or a 9.5 mm (height), 2.5-inch Serial ATA type hard
disk.

Before the upgrade

drive the system uses, you need to follow the steps below to
remove the hard disk drive and identify the drive’s model number.
Then, look up the drive’s model number in the HDD manufacturer’s
website to find out what type of hard disk your notebook uses.

Be sure to make a backup copy of all your data before attempting
this operation.

Warning:

instructions carefully or have a qualified technician install it for you. Damages due to
mishandling of this procedure are NOT covered by the manufacture’s warranty.

Hard drive upgrade is a delicate process. Please observe the following

Warning:

 Do not drop or apply any shock.
 Do not press on the cover.
 Do not touch the connector with your fingertips.
 Mishandling of the hard drive can result in permanent loss of data. Make a

backup copy of the drive s content before you remove it.

Apply care when handling the hard disk.

Note:

Certain models that come with the IBM-brand hard drive emit a clattering

sound when it is being rattled. This is a normal condition.

4-2

: In order to find out what type of hard disk

■ chapter 4 upgrading your computer

Upgrading the Hard Disk Drive

To replace the hard disk drive, do the following:

1. Turn OFF the computer. Unhook the AC cord and all
cables/devices attached to the notebook. Remove the battery.

2. Place your hand on a large metal object momentarily to
discharge any static electricity.

3. Locate and remove Screw A.

4. Remove HDD Cover.

5. Push the HDD module to the right and separate it from
the connector. Lift the module away from the bay.

4-3

■ chapter 4 upgrading your computer

6. Locate and remove 4 Screw B’s from the HDD module.
Remove the upper and lower metal cases.

7. Re-attach the metal cases to the new hard drive and
tighten 4 Screw B’s. Note the green PC board of the hard disk
drive is facing up.

8. Re-attach the HDD module to the HDD connector.

9. Put the HDD cover back and re-attach Screw A.

Congratulations! You have now completed the hard drive

4-4

■ chapter 4 upgrading your computer

upgrade. When you boot up the PC, you may need to create a
primary HDD partition and reformat the new drive and re-install
O/S, drivers, and all the necessary applications.

4-5

■ chapter 4 upgrading your computer

Upgrading the System Memory

Many applications will generally run faster when the computer’s
dynamic memory capacity is increased. The computer provides two
DDR memory sockets, located underneath the System Device
Cover. You can increase the amount of memory by replacing the
existing one with a dual inline memory module (commonly known
as SO-DIMM) of a higher capacity. The SO-DIMM can be 128MB,
256MB, 512MB or higher in capacity. Depending on the model,
your computer may use DDR I SDRAM (2.5V) type or DDR II
SDRAM (1.8V) type.

Before the upgrade

the system uses, you need to reboot the system. The initial boot
message shows you what type of DDR SDRAM module your
notebook uses.

Warning:

instructions carefully or have a qualified technician install it for you. Damages due to
mishandling of this procedure are NOT covered by the manufacture’s warranty.

Memory upgrade is a delicate process. Please observe the following

: In order to find out what type of DDR module

Warning:

mode may cause permanent damage to the hardware. Make sure you turn off the
power and unplug the AC cord before proceeding with a memory upgrade.

Changing memory while your computer is in suspend or power-saving

Warning:

or the manufacturer; otherwise the system may become unstable.

You should only use the DIMM module that is approved by the reseller

4-6

■ chapter 4 upgrading your computer

Installing a memory module (DIMM) into the system

To install the DIMM, do the following:

1. Power OFF the notebook. Unplug the AC cord and all
cables/devices attached to the notebook. Remove the battery.

2. Place your hand on a large metal object momentarily to
discharge any static electricity. Place the notebook on a flat
surface and fully close the LCD lid.

3. Locate and remove 9 Screw C’s on the System Device
Cover.

4. Remove the System Device Cover. The DIMM socket is
now seen as shown below.

4-7

■ chapter 4 upgrading your computer

5. If you need to remove an old DIMM from the socket,
press out on the latches located on both edges of the socket at
the same time. The DIMM should pop up to an angle of 30
degree (see diagram below). Pull the DIMM module out of the
memory socket. Store away the DIMM for the future use.

4-8

6. Install the new DIMM module into the memory socket.
The DIMM will only fit in one orientation. Insert the DIMM at an
angle of approximately 30 degrees into the empty memory
socket. Then press it firmly so that the contact edge is driven
into the receiving socket.

■ chapter 4 upgrading your computer

7. Pivot the DIMM until the latches on both sides of the
socket snap into place.

Note:

Notice the notch on the DIMM. The notches should fit nicely with the

socket.

8. Put the System Device Cover back and tighten 9 Screw
C’s.

Congratulations! You have just completed the memory upgrade.
When you boot up the computer , you should expect to see an

4-9

■ chapter 4 upgrading your computer

increase in DRAM capacity.

Your computer has been tested with a wide range of DIMM on the

Note:

market. However, not all memory modules are compatible. Check with your
system vendor for a list of compatible DIMM for your computer.

4-10

■ chapter 4 upgrading your computer

Adding a Mini-PCI Type Wireless LAN Card
(Optional Device)

Your computer comes with a unique Mini PCI Card so cket, which is
located next to the DRAM socket and underneath the WLAN
Module Cover. The socket allows the computer to add unique
features such as wireless LAN (IEEE802.11x). Ask your dealer on
the availability of the mini PCI card.

Warning:

following instructions carefully or have a qualified technician install it for you.
Damages due to mishandling of this procedure are NOT covered by the
manufacture’s warranty.

Warning:

power-saving mode may cause permanent damage to the hardware. Make sure you
turn off the power and unplug the AC cord before proceeding with a memory
upgrade.

Installing a mini PCI card is a delicate process. Please observe the

Installing the mini PCI card while your computer is in suspend or

4-11

■ chapter 4 upgrading your computer

Installing a Mini PCI Card into the System

To install a new Mini PCI card, do the following:

1. Follow steps in the previous section, Installing a memory
module (DIMM) into the system, to access the Mini PCI Socket.

4-12

2. The mini PCI card will only fit in one direction. Align the
small notch in the module with the socket on the connector and
insert the card at an angle of approximately 30 degrees into the
empty socket. Then press it firmly so that the contact edge is
driven into the receiving socket. Pivot the mini PCI card until
the latches on both sides of the socket snap into place.

Note:

If you want to remove a mini PCI card from the socket, press out on the
latches located on both edges of the socket at the same time. The card should
pop up to an angle of 30 degree.

■ chapter 4 upgrading your computer

3. Locate 2 antenna cables with connectors. Snap the cable
onto the golden connector on the Mini PCI Wireless LAN card.

(Note: The connectors are fairly small! This may take some
maneuvering. You may want to connect the antenna cables
before inserting the wireless card into the socket. )

4. Put the System Device Cover back and tighten 9 Screw
C’s.

Congratulations! You have now completed the mini PCI card
installation. During the next time the system boots to Windows,
the system will prompt for driver location. Insert the Factory
CD-ROM and point to the directory where the Wireless LAN
driver can be found. In addition to installing the driver, you may
also need to run a Setup.exe program to install the card’s utility
applications before it is fully operational.

4-13

■ chapter 5 trouble shooting

CHAPTER▼ FIVE

TROUBLE SHOOTING

In this chapter, you will learn how to
solve common hardware and software
problems.

5-1

■ chapter 5 trouble shooting

Your computer has been fully tested and complies with the

system specifications before shipping. However, incorrect
operations and/or mishandling may cause problems.

This chapter provides a reference for identifying and correcting
common hardware and software problems that you may encounter.

When you encounter a problem, you should first try to go through
the recommendations in this chapter. Instead of returning the
computer and waiting for repair, you may easily solve the problems
by considering the following scenarios and possible solutions. If the
error continues, contact your reseller for service information.

Before taking further actions, consider the following
suggestions:

 Check to see if the problem persi sts when all the external
devices are removed.
 Check to see that the green light indicator on the AC adapter
is lit.
 Check to see the power cord is properly plugged to the wall
outlet and to the computer.

 Check to see the power indicator of the computer is on.
 Check to see if your keyboard is ope rati onal by pressing and

holding any key.
 Check for any incorrect or loose ca ble connections. Make
sure the latches on the connectors latch securely on to the receptor
end.
 Be sure you have not performed an incorrect setting on the

5-2

■ chapter 5 trouble shooting

hardware devices in the BIOS Setup utility. A faulty setting may
cause the system to misbehave. If you are not sure of the changes
you made, try to restore all the settings to factory defaults.
 Be sure all the device drivers are installed properly. For
example, without the audio driver properly installed, the speakers
and microphone will not work.
 If external devices such as USB camera , scanner, printer do
not function correctly when connected to the system, it is usually
the device’s own problem. Consult the device’s manufacturer first.
 Some softwa re programs, which have not gone through
rigorous coding and testing, may cause problems during your
routine use. Consult the software vendor for problem solving.
 Legacy peripheral are not plug-and-play capable. You need
to restart the system with these devices powered up and connected
first.
 Be sure to go to BIOS SETUP and load DEFAULT SETTING
after BIOS re-flash.
 Be sure the Quick Key Lockout Switch on the bottom of the
computer is not engaged; otherwise the quick keys will not work.

5-3

■ chapter 5 trouble shooting

Audio Problems

No Audio output -

 Software volume cont rol is turned down in Microsoft
Sound System or is muted. Double-click the speaker icon on
the lower right corner of the taskbar to see if the speaker has
been muted or turned down all the way.
 Most audio problems are soft ware-related. If your
computer worked before, chances are software may have been
set incorrectly.
 Go to [Start > Settings > Control Panel] and double-click
the Sounds and Audio Devices icon. In the Audio page, make
sure that Realtek HD Audio is the default playback device.

Sound cannot be recorded -
 Double-click the speaker icon on the lower right corner of
the taskbar to see if the microphone has been muted.

1. Click Options and select Properties.

2. Select Recording and click the OK button.

3. After Click OK button, the recording volume control panel

will appear.
 Go to [Start > Settings > Control Panel] and double-click
the Multimedia icon (or Sounds and Audio Devices icon). In the
Volume or Audio page, make sure that Realtek HD Audio is the
default recording device.

5-4

■ chapter 5 trouble shooting

Hard Disk Problems

The hard disk drive does not work or is not recognizable -

 If you had just performed a hard disk upgrade, make sure
the hard drive connector is not loose and the hard disk drive is
also correctly seated. Remove it and reinsert it firmly, and
restart your PC. (Refer to Chapter 4 for details.)
 The new HDD may need to be pa rtitioned and
reformatted. O/S and drivers will need to be re-installed as well.
 Check the hard disk indicator LED. When you access a
file, the LED lamp should light up momentarily.

 The new HDD may be defective or is not compatible.
 If your computer has been subjected to static electricity

or physical shock, you may have damaged the disk drive.

The hard drive is making abnormal whining noises -

 You should back up your files as soon as possible.
 Make sure the source of noise is inde ed from the hard

drive and not the fan or other devices.

The hard disk drive has reached its capacity -

 Run Disk Cleanup utility in Windows. [Start > All
Programs > Accessories > System Tools > Disk Cleanup] The
system will prompt you for what to do.
 Archive files or programs that you had no longer used by
moving them to an alternative storage medium (floppy disk,
optical record-able disk, etc.) or uninstall programs that no
longer use.
 Many browsers store files in the hard drive as a cache to
speed up the performance. Check the program’s Online Help

5-5

■ chapter 5 trouble shooting

for instructions on decreasing the cache size or on removing
temporary Internet files.
 Empty the Recycle Bin to create more disk space. When
you delete files, Windows saves them to the Recycle Bin.

The hard disk takes longer to read a file -

 If you have been using the drive for a period, the files
may be fragmented. Go to [Start > Programs > Accessories >
System Tools > Disk Defragmenter] to perform a disk
defragmentation. This operation may take a while.
 Interrupt requests or problems with other hardware
devices may have occupied the CPU and therefore slows down
the system performance.

The files are corrupted -

 Run the Error-checking utility in Windows to chec k the
HDD. Double-click My Computer . Right -cli ck C: and select
Properties. Click Check Now in Error- checking in Tools.

5-6

■ chapter 5 trouble shooting

Optical Drive Problems

The optical drive does not work -

 Try rebooting the system.
 The disk is damaged or files are not readabl e.
 After you have inserted a CD-ROM disk, it may take a

moment before you can access its content.

The drive dose not read any disks -

 The CD may not be properly seated in the tray. Make
sure the disk is firmly seated onto the spindle.
 The disk is damaged or not readable.

The disk cannot be ejected -

 Normally, it takes a few seconds to eject the disk.
 If the disk cannot be ejected, it may be mechanically

jammed. Straighten out a paper clip and insert it to a tiny hole
next to the eject button. This should reject the disk tray. If not,
return the unit for repair. Do not forcefully pull on the disk tray.

The Combo or DVD RW drive (optional device) cannot
record -

 You need to purchase and install a burner utility program
to record files to a blank media.

5-7

■ chapter 5 trouble shooting

Display Problems

The display panel is blank when the system is turned on -

 Make sure the computer i s not in the Standby or
Hibernate suspend modes. The display is turned off to
conserve energy in these modes.

The screen is difficult to read -

 The display resolution should at least be set to at
least1024x768 for optimal viewing.

1. Go to [Start > Settings > Control Panel] and double-click
the Display icon.

2. Under the Settings page, set screen resolution to at least
1024x768 and choose at least 256 colors.

The screen flickers -

 It is normal if the display flickers a few times during
shutting down or powering up.

5-8

■ chapter 5 trouble shooting

Keyboard and Mouse Problems

The built-in touch pad performs erratically -

 Make sure there is no excess perspiration or humidity on
your hand when using the touch pad. Keep the surface of the
touch pad clean and dry.
 Do not rest your palm or wrist on the surface of the touch
pad while typing or using the touch pad.

The built-in keyboard accepts no input -

 If you are connecting an external keyboard to the system,
the built-in keyboard may not work.
 Try restarting the system.

The characters on the screen repeat while I type.

 You may be holding the keys down too long while you’re
typing.
 Keep the keyboard clean. Dust and dirt under the keys
could cause them to stick.
 Configure the keyboard to wait longer before the auto
repeat feature starts. To adjust this feature, Go to [Start >
Settings > Control Panel], and double-click the Keyboard icon.
A dialogue bo x shows up with the adjustable settings for the
keyboard.

5-9

■ chapter 5 trouble shooting

CMOS Battery Problem

A message “CMOS Checksum Failure” displays during the
booting process or the time (clock) resets when booting -

 Try to reboot the system.
 If the message “CMOS Checksum Failure” appears

during the booting procedure even after rebooting, it may
indicate failure of the CMOS battery. If so, you need to replace
the battery. This battery normally lasts two to five years. The
battery is of type CR2032 (3V). You may replace it by yourself.
The battery is located under the System Device Cover on the
bottom of the notebook. See Chapter 4 for more details.

5-10

■ chapter 5 trouble shooting

Memory Problems

The POST does not show an increased memory capacity
when you have already installed additional memory -

 Certain brands of memory module may not be
compatible with your system. You should ask your vendor for a
list of compatible DIMM.
 The memory module may not be installed properly. Go
back to Chapter 4 to review the details of this operation.
 The memory module may be defective.

The O/S issues an insufficient memory error message
during operation -

 This is often a software or Windows-related problem. A
program is draining the memory resources.
 Close the application programs you’re not using and
restart the system.
 You need to install additional memory module. For
instructions, go to Chapter 4 Upgrading Your Computer.

5-11

■ chapter 5 trouble shooting

Modem Problems

The built-in modem does not respond -

 Make sure the modem driver is loaded properly.
 Go to [Start > Settings > Control Panel > Phone and

Modem Options] and go to Modems tab. Make sure SmartLink
56K Voice Modem or Uniwill V.92 Modem is listed. Otherwise,
click the Add button to add the modem d rive, which is located in
the factory CD-ROM (or floppy diskette).
 Go to [Start > Settings > Control Panel > System] and
click Device Manager button in the Hardware page to check for
possible resource or driver conflict. See Windows on-line help
or manual for how to handle such problems.
 Make sure the phone line, whi ch the co mputer is
connected to, is working.

Connection difficulties -

 Be sure to disable Call Waiting on the phone line.
 Be sure to have the correct country setting where your

computer is used. [Start > Settings > Control Panel > Modem
Settings > Configuration] In the Country/Area pull-down menu,
select the appropriate country setting.
 Excessive line noise might cause the connection to b e
dropped. To check this, put the regular phone handset on the
line and placing a phone call. If you do hear abnormal noise, try
to make the modem connection with a different line or contact
your local telephony company for service.

 Make sure the cable co nnection is firm.
 Try a different receiver number and see if the problem

persists.

5-12

■ chapter 5 trouble shooting

Network Adapter / Ethernet Problems

The Ethernet adapter does not work -

 Go to [Start > Settings > Control Panel > System >
Hardware > Device Manager]. Double-click on Network
Adapters and check if Realtek RTL8139/810x Family Fast
Ethernet NIC (or Realtek RTL8169/8110 Family Gigabit NIC)
appears as one of the adapters. If it does not exist, Windows
has not detected the Ethernet NIC or the device driver has not
been installed properly. If there is a yellow mark or red-cross on
the network adapter, it may be a device or resource conflict.
Replace or update the device driver from the factory CD-ROM
disk or consult Windows manual on how to solve the resource
conflict problem.
 Make sure the physical connections on both ends of the
cable are good.
 The hub or concentrator may not be working prop erly.
Check to see if other workstations connected to the same hub
or concentrator is working.

The Ethernet adapter does not appear to operate in the
100/1000Mbps transmission mode -

 Make sure the hub you are using supports
100/1000Mbps operation.
 Make sure that your RJ-45 cable meets the
100/1000Base-TX requirements.
 Make sure the Ethernet cable is connected to the hub 　
socket that supports 100/1000Base-TX mode. The hub may
have both 100Base-TX and 1000Base-T sockets.

5-13

■ chapter 5 trouble shooting

PC Card / PCMCIA Problems

PC Cards do not function-

 Make sure you have properly installed the driver for the
card.
 Consult the card’s man ual or contact the vendor for
trouble-shooting.

The PC card cannot be recognized -

 Windows NT4.0 does not support PCM CIA (PC Card)
function. You may need an external program for this.
 Make sure the card is fully inserted; the outer end of the
card should be even with the edge of the computer.

 Remove and insert the PC card again.
 Make sure there is no IRQ conflict with the card. See

Windows on-line help for solving IRQ conflicts.

 Reboot the computer and see if the problem persists.
 The card may be defective. Try the card on another

system, if possible.

Windows crashes or freezes when you remove the PC
card-

 Make sure you have <Stop> the PC card before
removing it. Double-click the Safely Remove Hardware icon at
the lower right corner of the task bar and select the card you
wish to stop. When you click <Close>, in f ew second s Windows
will prompt you to remove the card.

5-14

■ chapter 5 trouble shooting

Performance Problems

The computer becomes hot -

 In a 35
computer’s back case are expected to reach 50 degrees.

 Make sure the air vents are not blocked.
 If the fan does not seem to be working at high

temperature (50 degrees Celsius and up), contact the service
center.
 Certain programs that are processor-intensive may
increase the computer temperature to a degree where the
computer automatically slows down its CPU clock to protect
itself from thermal damage.

The program appears stopped or runs very slowly -

 Press CTRL+ALT+DEL to see if an application is still
responding.

 Restart the computer.
 This may be normal for Windows when it is processing

other CPU-intensive programs in the background or when the
system is accessing slow-speed devices such the floppy disk
drive.
 You may be running too many applications. Try to close
some applications or increase system memory for higher
performance.
 The processor may have been overheated due to the
system’s inability to regulate its internal heat. Make sure the
computer’s ventilation grills are not blocked.

o

C environment, the certain areas of the

5-15

■ chapter 5 trouble shooting

Firewire (IEEE1394) and USB2.0 Problems

The USB device does not work -

 Windows NT 4.0 does not support USB protocols
 Check the settings in the Windows Control Panel.
 Make sure you have installed the necessary device

drivers.
 Contact the device vend or for additional support.

The IEEE1394 port does not work -

 Go to [Start > Settings > Control Panel > System >
Hardware > Device Manager]. You should see an entry which
reads “Texas Instrument OHCI Compliant IEEE 1394 Host
Controllers”. If it does not exist, Windows has not detected the
host controller or the device driver has not been installed
properly. If there is a yellow mark or red-cross on the 1394 host
controller, it may be a device or resource conflict. Replace or
update the device driver from the factory CD-ROM disk or
consult Windows manual on how to solve the resource conflict
problem.

 Make sure the cable is fully connected.
 Make sure you have installed the necessary device

drivers.
 Contact the device vend or for additional support.

5-16

■ appendix A product specification

A

APPENDIX▼ A

PRODUCT SPECIFICATION

-1

■ appendix A product specification

A

▼ Processor and Core Logic

 Processor

 Core Logic

z Mobile Intel Pentium M (Dothan), up to 2.13GHz,

2 MB L2 cache or

z Mobile Intel Celeron M, up to 1.70GHz, 1MB L2

cache
Intel Alviso 915GM + ICH6-M (FW82801FBM) chipset
with video, audio, modem, and USB2.0 controllers
integrated
533 MHz (Pentium M) / 400 (Celeron M) Front Side
Bus
400/533 MHz DDR1 / DDR2 interface

▼

System Memory

 Memory Type

 Default

 Memory

Expansion

DDR1 / DDR2 SDRAM 333/400/533MHz, PC2700 and
PC2 3200/4200 compatible
128 / 256 / 512MB, 2.5-Volt (DDR1) or 1.8-Volt (DDR2)
64-bit bus
Two 200-pin DIMM sockets

▼

Display

 LCD Panel

 Graphic

Accelerator

 Motion

Playback

 Other

Features

z 15-inch SXGA+ (1400x1050) TFT LC D or
z 15-inch XGA (1024x768) TFT LCD or
z 15.4-inch WXGA (1280x800) TFT LCD or
z 15.4-inch WSXGA+ (1680x1050) TFT LCD

Intel Integrated GMA900 Extreme3 graphic engine

Hardware Motion Compensation and IDCT Supported
for MPEG1/2 Playback
Direct3D compatible, Direct X compatible

-2

■ appendix A product specification

A

▼ Audio

 Chipset

 Chipset
 Audio Codec

 Audio Codec
 Sound

 Sound

Capabilities

Capabilities

Intel (ICH6M) integrated audio controller
Realtek ALC880
DirectSound 3D, EAX 1.0 & 2.0 compatible
A3D, I3DL2 compatible
AC97 V2.3 compatible

7.1 Multi-channel compatible (through S/PDIF)
Supports Azalia standard
2 Stereo Speakers

▼

Modem

 Chipset

 Transmission

Rate

Intel (ICH6M) integrated Modem Controller with MDC
card.
V.92 / V.90 / K56flex for download data speed up to
56Kbps.
V.34, V.17, V.29 protocol supported

▼ Wireless LAN

 Module
 Transmission

Protocol

Intel PRO/Wireless 2200, MiniPCI Interface
IEEE802.1 1 B&G

-3

■ appendix A product specification

A

▼ LAN / Ethernet

 Chipset

 Chipset

 PnP Function

 Flow Control

 PnP Function
 Speed

 Flow Control

Selection

 Speed
 Other

Selection
Features

 Other

Features

z Realtek 8100CL Ethernet function for

10/100Base-TX network standards or
z Realtek 8110SBL Ethernet function for

10/100/1000Base-TX network standards
Windows 2000 / XP Plug and Play compatible
Automatic Jam and auto-negotiation for flow control
Auto Negotiation and Parallel detection for automatic
speed selection (IEEE 802.3u)
High performance 32-bit PCI bus master architecture
with integrated DMA contro ller for low CPU and bus
utilization
Remote Wake-up Scheme supported
Hot Insertion supported
Remote Wake-up Scheme supported
Hot Insertion supported

▼

Firewire IEEE1394(a)

 Chipset

 Capabilities

TI TSB43AB22A IEEE1394 OHCI Host Controller and
Up to 400 Mbps
Expandable up to 63 devices in chains

▼

Storage

 Hard Drive

 Combo Drive

 DVD±R/±RW

or DVD-Dual or
DVD-Multi
Standards

z S-ATA 2.5-inch format hard disk drive
z P-ATA 2.5-inch format hard disk drive

5.25-inch format (12.7mm height) fixed module
(Optional Purchase)

5.25-inch format (12.7mm height) fixed module
(Optional Purchase)

-4

■ appendix A product specification

A

▼

Keyboard & Touch pad

 Keyboard

 Touch pad

 Chipset
 PC Card

 4-in-1 Card

Reader Format
Support

 Mic-In Port
 Audio-Out / SPDIF
 Audio-in Port
 Firewire
 USB2.0 Port

 Ethernet
 Modem
 S-Video
 Power-In
 VGA Port
 Card Reader
 PC Card Slot

87-key or 86-key QWERTY keyboard with embedded
numeric keypad and Windows keys, 19.05mm Pitch
Built-in Touch Pad

▼

PC Card & Multiple Card Reader

TI1410 (PC Card), Genesys GL817E (Card Reader)
Single Slot TYPE II, Hot insertion and removal
supported
Multimedia Card (MMC), Secure Digital Card (SD),
Memory Stick (MS), and MS Pro Card

▼

Ports and Connectors

One Microphone-in jack
One Headphone / SPDIF jack
One Line-in jack
One Firewire (IEEE1394) host connector
Three USB2.0-compliant connectors + One for Built-in
for Bluetooth or other USB integrated device
One standard network Ethernet connector (RJ-45)
One modem / phone connector (RJ11)
One S-video (TV-out) output connector
One DC-in connector
One 15-pin VGA connector
One 4-in-1 Card Reader slot
One PC Card Slot (type II)

-5

■ appendix A product specification

A

▼ Battery Pack / AC Adapter

 Primary

Battery Pack

 Feature

 Adapter

AC-Input /
DC-Output

z Li-ion 6-Cell pack, 11.1V x 4400 mAH or
z Li-ion 6-Cell pack, 10.8V x 4400 mAH or
z Li-ion 9-Cell pack, 10.8V x 6600 mAh

Low battery state with low battery warning beep
Uniwill SmartPower Power Management
Smart Battery Compliant; low battery warning beep

Autosensing AC-in 100~240V, DC-out 20V, 65W

▼

BIOS

 PnP Function
 Self Test
 Auto

Detection

 Power

Management

 Security
 Other

Features

AMI PnP BIOS
Power On Self Test
DRAM auto-detection, auto-sizing
L2 Cache auto-detection
Hard disk type auto-detection
APM 1.2 (Advanced Power Management) &
ACPI 2.0 (Advanced Configuration Power Interface)
Two Level Password Prote ction s
32bit access, Ultra DMA, PIO5 Mode support
Multi-boot capability

 O/S

Compatible with Microsoft Windows 2000 / XP / DOS

-6

■ appendix A product specification

A

▼ Physical Specification

 Dimension

 Weight

 Environmental

Limits

z 255EI: 333 (W) x 272 (D) x 25.3~35.7 (H) mm
z 259EI: 358 (W) x 272 (D) x 25.9~34.1 (H) mm
z 255EI: 6.43 lbs / 2.92 Kg

Drive, and 6-cell battery pack)
z 259EI: 6.7 lbs / 3.04 Kg

Drive, and 6-cell battery pack)
Operating Temperature: 5 to 30
Operating Humidity: 20 to 90 percent RH (5 to 35
Storage Temperature: -15 to 50

(with 15”LCD, DVD-ROM

(with 15.4”LCD, DVD-ROM

o

C (41 to 86oF)

o

C (-5 to 122oF)

o

C)

-7

■ appendix B agency regulatory notices

APPENDIX▼ B

AGENCY REGULATORY NOTICES

B-1

■ appendix B agency regulatory notices

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interferen ce
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and the receiver.
 Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

 Consult the dealer or an experienced radio or television technician

for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authorit y to operate
this equipment.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance.

This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.
"Uniwill declare that 255EIx/259EIx (with wireless card: Intel
WM3B2200BG/ WM3B2915ABG) is limited in CH1~CH11 by specified
firmware controlled in USA."

This device is intended only for OEM integrators under the following
conditions:

B-2

■ appendix B agency regulatory notices

1) The transmitter module may not be co-located with any other
transmitter or antenna.

As long as conduction above is met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed (for Notebook).

IMPORTANT NOTE: In the event that these conditions can not be met
example certain laptop configurations or co-location with another
transmitter), then the FCC authorization is no longer considered valid and
the FCC ID can not
the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.

be used on the final product. In these circumstances,

(for

End Product Labeling

The final end product must be labeled in a visible area with the following:
“Contains TX FCC ID:”.PD9WM3B2200BG /PD9WM3B2915ABG

Manual Information That Must be Included

The OEM integrator has to be aware not to provide information to the end
user regarding how to install or remove this RF module in the users manual
of the end product which integrate this module.

The users manual for OEM integrators must include the following
information in a prominent location “ IMPORTANT NOTE: To comply with
FCC RF exposure compliance requirements. The antenna must not be
co-located or operating in conjunction with any other antenna or
transmitter.

Modifications

The FCC requires the user to be notified that any changes or modifications
made to this device that are not expressly approved by the Manufacture
may void the user’s authority to operate the equipment.

Connections to Peripheral Devices

Connections to this device must be made with shielded cables with metallic
RFI/EMI connector hoods to maintain compliance with FCC Rules and
Regulations.

B-3

■ appendix B agency regulatory notices

Declaration of Conformity

This device complies with Part 15( CLASS B
is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

European Notice

Products with the CE Marking comply with both the EMC Directive
(89/336/EEC) and the Low Voltage Directive (73/23/EEC) and R&TTE
Directive (1999/5/EC) issued by the Commission of the European
Community.
Compliance with these directives implies conformity to the following
European Norms:

 EN55022 : 1998+A1: 2000+A2: 2003, CLASS B
 EN61000-3-2 : 2000
 EN61000-3-3 : 1995+A1: 2001
 EN55024 : 1998+A1 : 2001+A1: 2003
 IEC61000-4-2: 2001
 IEC61000-4-3:2002+A1:2002
 IEC61000-4-4:1995+A1:2000+A2:2001
 IEC61000-4-5:2001
 IEC61000-4-6:2001
 IEC61000-4-8:2001
 IEC61000-4-11:2001
 EN50082 (IEC801-2, IEC801-3, IEC801-4) Electro-magnetic

Immunity

 EN 300 328-2, EN 300 328-1, EN 301 489-1, EN 301 489-17 (ETSI

300 328, ETSI 301 489) Electro-magnetic Compatibility and Radio
Spectrum Matter.

 TBR21 ( ETSI TBR21) Terminal Equ ipment.
 EN60950 (IEC950) I.T.E. Product Safety

Canadian Notice

This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the radio interference
regulations of the Canadian Department of Communications.

Le present appareil numerique nemet pas de bruits radioelectriques
depassant les limites applicables aux appareils numeriques de Classe B
prescrites dans le reglement sur le brouillage radioelectrique edicte par le
Ministere des Communications du Canada.

B-4

)/68 the FCC Rules. Operation

■ appendix B agency regulatory notices

Power Cord Requirement

The power cord supplied with the AC adapter should match the plug and
voltage requirements for your local area. Regulatory approval for the AC
adapter has been obtained using the power cord for the local area.
However, if you travel to a different area and need to connect to a different
outlet or voltage, you should use one of the power cords listed below. To
purchase a power cord (including one for a country not listed below) or a
replacement ac adapter, contact your local dealer.

U.S. and Canada

 The cord set must be UL-Listed and CSA-Certified or C-UL Listed.
 The minimum specifications for the flexible cord are (1) No. 18 AWG,

(2) Type SJ, and (3) 3-conductor.

 The cord set must have a rated current capacity of at least 10 A.
 The attachment plug must be an earth-grounding type with a NEMA

5-15P (15A, 125V) or NEMA 6-15P (15 A, 250V) configuration.

Japan

 All components of the cord set (cord, connector, and plug) must bear

a `PSE` mark and registration number in accordance with the
Japanese Dentori Law.

 The minimum specification for the flexible cord are: (1) 0.75 mm

2

conductors, (2) Type VCT or VCTF, and (3) 3-conductor.

 The cord set must have minimum rated current capacity of 7 A.
 The attachment plug must be a two-pole, grounded type with a

Japanese Industrial Standard C8303 (15 A, 125 VAC) configuration.

Other Countries

 The cord set fittings must bear the certification mark of the agency

responsible for evaluation in a specific country. Acceptable agencies
are:

BSI (UK)
OVE (Australia)
CEBEC (Belgium)
SEMKO (Sweden)
FIMKO (Finland)
DEMKO (Denmark)
NEMKO (Norway)
SETI (Finland)
EANSW (Australia)
SEV (Switzerland)
IMQ (Italy)
UTE (France)

B-5

■ appendix B agency regulatory notices

CCC (China)
PSB (Singapore)
PSE (Japan)
BSMI (Taiwan)
B (Polish)
VDE (Germany)
SASO (Saudi Arabia)

 The flexible cord must be of a HAR (harmonized) type HO5VV-F

3-conductor cord with a minimum conductor size of 0.03 square
inches.

 The minimum specification for the flexible cord for Class II product

are: (1) 2X0.75 mm

2

conductors, (2) 2-conductor cord.

 The cord set must have a current capacity of at least 10 A and a

nominal voltage rating of 125 / 250 VAC.

CAUTION: MODEL 255EIx / 259EIx IS DESIGNED TO USE WITH THE
FLLOWING AC ADAPTER MODEL ONLY
Manufacture: LITE-ON ELECTRONICS, INC
Model: PA-1650-02 (65W)
Manufacture: LISHIN INTERNATIONAL ENTERPRISE CORP.
Model: 0335A2065 (65W)
Manufacture: Electricity Power Source
Model: F10653-A

Telephone lines requirement

 The appropriate utilization of 26AWG telephone line cord on unit.
CAUTION: Always disconnect all telephone lines from the wall outlet
before servicing or disassembling this equipment.
CAUTION: To reduc e the risk of fire, use only No. 26AWG or larger
telecommunication line cord.

Battery Pack Safety

 The battery pack is intended to use only with this notebook.
 Do not dis assemble the pack.
 Do not dispose of the battery pack in fire or water.
 To avoid risk of fire, burns, or damage to your battery pack, do not

allow a metal object to touch the battery contacts.

 Handle a damaged or leaking battery with extreme care. If you come

in contact with the electrolyte, wash the exposed area with soap and

B-6

■ appendix B agency regulatory notices

water. If it contacts the eye, flush the eye with water for 15 minutes
and seek medical attention.

 Do not charge the battery pack if the ambient temperature exceeds

45℃ (113℉).

 To obtain a replacement battery, contact your local dealer.
 Do not expose the battery pack to high storage temperatures (above

60℃, 140℉).

 When discarding a battery pack, contact your local waste disposal

provider regarding local restrictions on the disposal or recycling of
batteries.

 Use only supplied AC Adapter for charging.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace

only with same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions or local
laws.

VORSICHT! Explisionsgefahr bei unsachgernazen Austausch der Batterie.
Ersatz nur durch denselben oder einem vom Hersteller empfohlenem
ahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des
Herstellers.

Laser Safety

The optical drive used with this computer is certified as a Class 1 laser
device according to the U.S. Department of Health and Human Services
(DHHS) Radiation Performance Standard and International Standards IEC
825 / IEC 825-1 (EN60825 / EN60825-1). The device is not considered
harmful, but the following precautions are recommended:

 Do not open the unit.
 Avoid direct exposure to the laser beam.
 If the unit requires service, contact an authorized service center.
 Ensure proper use by reading and following the instructions carefully.
 Do not attempt to make any adjustment of the unit.

CLASS 1 LASER PRODUCT
APPAREIL A LASER DE CLASSE 1
LASERSCHUTZKLASSE 1 PRODUKT

B-7

■ appendix B agency regulatory notices

Warning!

Do not attempt to disassemble the cabinet containing the laser. The laser
beam used in this product is harmful to the eyes. The use of optical
instruments, such as magnifying lenses, with this product increase the
potential hazard to your eyes. For your safety, have this equipment
serviced only by an authorized service provider.

Lithium battery warning / Bridge battery warning

This computer contains a lithium battery to power the clock and calendar
circuitry.

CAUTION: Danger of explosion if battery is replaced incorrectly. Replace
only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.

ATTENTION: Il y a danger d’xplosion s’il y a remplacement incorrect de la
batterie. Remplacer uniquement avcc unc batterie du meme type ou d’un
type recommande par le constructer. Mettre au rebut les batteries usagees
conformement aux instructions du fabricant.

VORSICHT! Explosionsgefahr bei unsachgemBen Austausch der Batterie
Ersatz nur durch denselben oder einem vom Hersteller empfohlenem
ahnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des
Herstellers.

Der Arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 betragt 70dB
(A) oder weniger.

Zum Netzanschlua dieses Gerates ist eine geprufte Leitung zu verwenden.
Fur einen Nennstrom bis 6A und einem Gerategewicht groBer 3kg ist eine
Leitung nicht leichter als (1)H05VV-F, 3G, 0.75mm

conductors

einzusetzen.

2

(2)2X0.75 mm

2

Die Steckdose muB nahe dem Gerat angebracht und leicht
zuganglich sein.

CAUTION!
T his pa rt is h ot. Be Care ful.
VORSICHT!
Di ese F la ch e wird se hr heiss.

When you see this symbol, be careful as this spot may be very hot.

B-8