Elinchrom ZOOM Pro HD, ZOOM Action, ZOOM Pro User Manual
Elinchrom SA ZOOM Head - Made in Switzerland - 12.07.2011 (73012)
USER MANUAL
GEBRAUCHSANLEITUNG
MANUEL D’UTILISATION
MANUALE D’USO
MANUAL DE INSTRUCCIONES
EN
DE
FR
IT
ES
ZOOM Pro HD - 20192
ZOOM Pro - 20191
ZOOM Action - 20193
is a registered trademark of ELINCHROM LTD, RENENS, SWITZERLAND
EN
2
User Manual
Table of contents
Introduction 3
Declaration of conformity 4
CE / Disposal 4
Characteristics 5
User Safety Information 6
Before You Start 8
Replacing the Plug-In Flash Tube 9
ZOOM Head Accessories 10
Technical Data 11
Maintenance 12
Warranty 62
EN
3
User Manual
INTRODUCTION
Dear photographer
Thank you for buying the ELINCHROM ZOOM FLASHHEAD for the ELINCHROM power
pack range. All Elinchrom products are manufactured using the most advanced technology.
Carefully selected components are used to ensure the highest quality and the equipment
is submitted to many tests both during and after manufacture. We trust that it will give you
many years of reliable service.
Please read the instructions carefully, before use, for your safety and to obtain
maximum benefit from the many features.
Your Elinchrom-Team
Please read carefully the notes about this manual…
This manual may show images of products with accessories, which are not part of Sets or
single units.
Elinchrom set and single unit configurations may change without advise and may differ in
other countries.
Please find actual configurations at www.elinchrom.com
For further details, upgrades, news and the latest information about the Elinchrom
System, please regularly visit the Elinchrom website. The latest user guides and technical
specifications can be downloaded in the “Support” area.
Technical data, features and functions of Elinchrom flash units, accessories and the ELSkyport system may change without advice.
The listed values can differ due to tolerances in components, or measuring instruments.
Technical data, subject to change. No guarantee for misprints.
EN
4
User Manual
DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
This device may not cause harmful interference.
1. This device must accept any interference received, including interference that may
cause undesired operation.
Product name: ZOOM HEAD
Trade name: ELINCHROM
Model number(s): Pro HD: 20192 Action: 20193 Pro: 20191
Name of responsible party: Elinchrom S.A.
Av. De Longemalle 11
CH - 1020 Renens / Switzerland
Phone: +41 21 637 26 77
Fax: +41 21 637 26 81
E-Mail: elinchrom@elinchrom.ch
ELINCHROM S.A. hereby declares that the equipment bearing the trade name and model
number specified above was tested conforming to the applicable FCC rules, and that all the
necessary steps have been taken and are in force to assure that the production units of the
same equipment will continue to comply with the Commissions requirements.
CE MARKING
The shipped version of this device complies with the requirements of
EMC directives
(EMC 2004/108/EC) «Electromagnetic compatibility» and (Low voltage
2006/95/EC) «Low voltage directive».
EN
5
User Manual
CHARACTERISTICS
• Three versions; ZOOM PRO HD, ZOOM ACTION and ZOOM PRO
• NEW: ZOOM function for flash tube and halogen modelling lamp.
• The ZOOM function is available from the left and right housing side
• ZOOM angle 50° to 66°, with 21 cm Reflector // 26141
• Up to 3000 ws maximum flash power, for the ELINCHROM power pack range.
• Up to 300 W halogen modelling lamp.
• High quality 5 m flash cable for maximum power and flexibility, also available as
Flashhead Extension cable in 5 m and 10 m.
• NEW: Reliable, high quality plug-in flash tube included.
• NEW: Protection glass dome included.
• Halogen lamp on/off switch.
• Centred umbrella fitting (7 mm).
• Extra umbrella fitting for other umbrella shaft sizes.
• NEW: Intelligent low noise fan cooling system. Electronically controlled the fan spins
slower or faster depending on the internal temperature of the head.
• Large handle with rubber grip.
• Small, robust and lightweight housing.
DISPOSAL AND RECYCLING
This device has been manufactured to the highest standards from materials, which can
be recycled or disposed of in a manner that is not environmentally damaging. The device
may be taken back after use to be recycled, provided that it is returned in a condition
that is the result of normal use. Any components not reclaimable will be disposed of in an
environmentally acceptable manner.
If you have any question on disposal, please contact your local office or your local
ELINCHROM Agent (please visit our website for a list of all ELINCHROM agents worldwide).
Loading...