Elinchrom SkyPort Speed User Manual
EL-SKYPORT TRANSMITTER SPEED
ERROR MANAGEMENT
DOWNLOAD THE ELB 400 USER GUIDE
Frequency
channel selector
MODE switch
GROUP switch
FREQUENCY CHANNEL
RX feature button
Power decrease
RX feature button
power increase or
modelling lamp toggle
Flash test / flash mode /
configuration button
Flexible swivel
antenna 360
Status LED
ERROR
NUMBER
1
3
4
15
60
90 Safety stop system (generic error)
2
11
61
DESCRIPTION SOLUTION
Capacitor over voltage
Discharge timeout error
Charge timeout error
Temperature sensor error
Communication bus error
System over heat
Battery low
Battery unseal error
Switch the unit off, wait 2 minutes
and switch the unit on again. If the
error shows up again the unit
requires a check up at an authorized
Elinchrom service centre.
Wait until the unit has cooled down.
The unit will switch back to the
normal operation as soon as the
temperature decreases to a normal
working level.
The unit has detected a mains
supply fault. Please check the
mains/battery supply. It could be
not working correctly.
Switch the unit off, wait 2 minutes
and switch the unit on again. If the
error shows up again the battery
requires a check up at an authorized
Elinchrom service centre.
Please get the complete user guide
is a registered trademark of ELINCHROM LTD, RENENS, SWITZERLAND
at this link:
http://bc.gs/32
Quick Start Guide
DOWNLOAD CONFORMITY
Please find the declaration for EC
conformity and USA & Canada
conformity on the Elinchrom website.
http://bc.gs/ec
EL-ENTERPRISE APP FOR iOS
Please download our corporate
™
iOS
App on App Store™:
™
http://bc.gs/14
Please check all security documents before use !
Elinchrom LTD - ELB 400 - Made in Switzerland
Av. de Longemalle 11, P. O. Box -458, CH-1020 Renens, Switzerland,
Tel. : + 41 21 637 26 77 Fax: +41 21 637 26 81 E-mail: elinchrom@elinchrom.ch
www.elinchrom.com
Elinchrom LTD - ELB 400 - Made in Switzerland - 01.2015 (73036)
ELB 400
DISPLAY PANEL - DASHBOARD CONTROL PANEL BATTERY BOX INFO
1 2 3
17
16
15
EL-Skyport synchronisation speed
1
EL-Skyport frequency channel
2
EL-Skyport group number
3
Photocell status
4
Ready beep
5
Recycling time
6
Battery level
7
Power in J
8
Pilot lamp timer
9
4 5 6 7
121314
DISPLAY PANEL - MAIN MENU
1
6
345
> 85%
70% ~ 85%
55% ~ 70%
8
9
10
11
10
11
12
13
14
15
16
17
1
2
3
2
4
5
6
40% ~ 55%
20% ~ 40%
< 20%
Flash function
Flash function value
Increase selected f-stop
Flash test
Decrease selected f-stop
Power of outlet A in f-stop
Total power in f-stop
Power of outlet B in f-stop
Menu title
Menu selected
Scroll down
Enter
Scroll up
(R)
(S)
(L)
Back to menu (Short press)
Back to dashboard (Long press)
(R)
(S)
(L)
B only 7-140 Ws
AS 33% 7-140 Ws
A only 21-424 Ws
AS 66% 14-280 Ws
Pilot lamp
Left Right
Set
selected timer (short press)
continuous (long press)
1° level 2° level 3° level
off
photocell
skyport (radio)
audio
flash mode
power settings
statistics
on
preflash
preflash setup manual block time timeframe
off (r.0)
normal (r.1)
speed (r.2)
group
channel
ready volume
error volume
key volume
ready tone
default
sequence
delayed sync set delay (in ms)
strobo
setup of activated mode
auto standby from[disabled] to [60 min.]
auto off
pilot lamp timer
recycling time eco mode fast mode
step per push 0.1 0.2 0.3
auto
group 1 to 4
channel 1 to 20
off min low default
off min low default
off min low default
tone 1 to 12
disabled enabledflash before ready
unit address total units seq. timeout
frequency duration
from[disabled] to [60 min.]
from[1"] to [60"]
0.4 0.5 1 in f-stop
high max
high max
high
max
A
1
Spare fuse
2
Fuse in use
3
Battery status
4
Charge socket
BATTERY LEVEL
75% -100%
50% -75%
25% - 50%
10% - 25%
< 10% (if blinking)
1B
2 3 4
A
Push Button
B
Security Lock
Loading...