Elinchrom Ranger RX Speed, Ranger Speed AS Operating Manual

English

elinca sa switzerland www.elinchrom.com

Operating Manual

Elinca S.A Ranger RX 01.06.2007 ENG (73300) Printed in Switzerland

Battery Power Pack

Ranger RX

1

P.S: Technical data subject to change.

The listed values are guide values which may vary due to tolerances in components used.

Introduction 2

Declaration of conformity, disposal and recycling, CE marking 3

Safety notice and precaution 4

Before you start 5

Control Panel 6

Functions 7, 8

Synchronisation, Wireless Remote control and ash triggering 9

Change the battery 9

Battery charging, battery fuses 10

Flashheads connections 10

Flashheads 11

Technical Data 12

Elinchrom Accessories 13

Guarantee 14

Table of contents

The quality of light and exceptional performance is the result of long research, application of
demanding principles, the long experience of ELINCHROM in lighting products for the studio
and the utilization of the latest technology in this area.

Totally integrated to the range of the ELINCHROM ashes, the Ranger RX units maintain the

traditional look and function that is ELINCHROM.

Ranger RX

The Elinchrom Ranger RX is manufactured by Elinca S.A. CH -1020 Renens/Switzerland

Dear Photographer,
Thank you for buying your Ranger RX autonomous ash unit.
All Elinchrom products are manufactured using the most advanced technology. Carefully
selected component are used to ensure the highest quality and the equipment is submitted to
many controls both during and after manufacture.
We trust that it will give you many years of reliable service.

All ash units are manufactured for the studio and location use of professional photographers.

Only by observance of the information given, can you secure your warranty, prevent possible
damage and increase the life of this equipment.

Note:

This equipement has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of

the FCC Rules and meets all requirements of the Canadian Interference-Causing Equipement Regulations. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipement

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipement does not cause harmful interferences to radio or television reception,

which can be determined by turning the equipement off and on, the user is encouraged to correct the interferences by one or

more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipement and receiver.

- Connect the equipement into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

ELINCA S.A. is not responsible for any radio or television interference caused by unauthorised modications of this

equipement or the substitution or attachment of connecting cables and equipement other than those specied by ELINCA S.A.

The correction of interference caused by such unauthorised modication, substitution or attachment will be the responsibility

of the user.

FCC Class B Compliance Statement

Introduction

2

3

CE marking

The shipped version of this device complies with the requirements of ECC directives
89/336/ECC «Electromagnetic compatibility» and 73/23/ECC «Low voltage directive».

Notational Conventions

The meaning of the symbols and fonts used in this manual are as follows:

Pay particular attention to text marked with this symbol.
Failure to observe this warning endangers your life, destroys the device, or may
damage other equipement

Supplementary information, remarks, and tips follow this symbol.
Text which follows this symbol describes activities that must be performed in the
order shown.

«Quotation marks» indicate names of chapters or terms

!

i

Disposal and recycling

This device has been manufactured to the highest possible degree from materials
which can be recycled or disposed of in a manner that is not enviromentally
damaging. The device may be taken back after use to be recycled, provided that is
returned in a condition that is the result of normal use. Any components not reclaimed
will be disposed of in a environmentally acceptable manner.

If you have any question on disposal, please contact your local ofce or your local ELINCHROM

agent (check our website for a list of all ELINCHROM agents world wide).

Product name: Professional Studio Flash unit

Trade name: ELINCHROM

Model number(s): Ranger RX

Name of responsible party: Elinca S.A

Av. De Longemalle 11
1020 Renens / Switzerland

Phone : [phone]

Fax: [phone]

We, ELINCA S.A., hereby declare that the equipement bearing the trade name and model number

specied above was tested conforming to the applicable FCC rules, and that all the necessary steps

have been taken and are in force to assure that the production units of the same equipement will
continue to comply with the Comissions requirements.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause
undesired operation.

Declaration of conformity

4

!

• Flash systems store electrical energy in capacitors by applying high voltage.

• For your safety, never open or disassemble your ashes.

• Only an authorised service engineer should open or attempt to repair the units.

• For repairs, take them to your elinchrom agent.

• Internal defect charge capacitors may explode whilst the unit is in use, never
switch on a not proper working ash unit.

Flash Tubes and Modelling lamps

• Flashtubes and modelling lamps in use are very hot!

• Never touch a ash tube or lamp before the unit cooled down and is disconnected from the mains.

• Do not re ashes from short distance (less than 1m) directed to a person and avoid looking
directly into the ashlight!

• Keep distance to ammable materials.

• Keep generally distance to operating units.

Outdoors

• A thermal cut out protects internal electronic components. At high ambient temperatures or

after rapid or frequent use, the thermal cut out may interrupt the capacitor charge. The display
will show “ER” .
After cooling down, the Generator restarts automatically. A Beep signal announces that
the unit is ready for operation, but note that it will only sound if the acoustic signal is switched on.

• The Ranger RX power pack is designed to keep out humidity and dust. When it is possible,

sockets should be sealed with the supplied caps and please ensure the Battery Box is secure
inside the Ranger RX housing.

• Never exchange the Battery under damp/humid conditions - look for a dry and clean area!!

• Avoid condensation related problems.

• Take care that the battery is well locked

• Do not use in restricted areas (like hospitals, etc.)

• Do not use in explosive environnements

Due to strict security regulations, please note :

• Remove the 30 A fuse from the top side of the Battery Box, this desactivates

the internal «Lead-Gel-Battery»

• Remove the Battery Box from the Ranger RX unit and store separately in your luggage.

• The sealed lead acid battery conrms to the special provisions of UN No. 2800/238.
Also this battery is satised with the special provisions A67 prescribed in

Non-Dangerous Goods Regulations by IATA

Travelling by Air (as well as any other transport option)

User Safety Information