Element TT3 User Manual
Headset User Guide
Warranty
Your TT3 headset has been carefully manufactured
and 100% tested using high quality assured
components. It is protected by warranty against
faulty workmanship and materials for a period of
24 months from the date of purchase. In the unlikely
event that a failure should occur, the unit will be
repaired or replaced free of charge when returned
postage paid to the address below, within the
24 month warranty.
This warranty does not cover damage or failure
resulting from misuse. Failure to comply with the
warnings, care and safety advice listed in this user
guide will void the warranty. This warranty does
not cover goods damaged in transit. Removing the
warranty tab thread on the headset cable will also
void warranty. Your statutory rights are in no way
aected by this warranty.
For service in or out of warranty please return the
unit postage paid to:
JPL Limited, Unit 1, Church Close Business Park,
Church Close, Todber, Sturminster Newton,
Dorset, DT10 1JH, ENGLAND.
When returning your unit please ensure that the
package contains a covering letter stating when and
where you purchased the unit and a description of
the problem encountered. If the unit is within the
warranty period please enclose proof of purchase.
Repair or replacement is at the discretion of the
manufacturer. In accordance with its policy of
progressive design, JPL reserves the right to alter
product specications at any time, without prior
notice.
Limited Warranty
Consequential and incidental damages, including
without limitation, loss of property and those arising
from breach of any express or implied warranty, are
not the responsibility of the retailer and to the extent
permitted by law, are excluded.
JPL Limited, Unit 1, Church Close Business Park,
Church Close, Todber, Sturminster Newton,
Dorset, DT10 1JH, ENGLAND.
Telephone: +44 (0)1258 820100
www.jpltele.com
7 9 108
Adjusting the Microphone Boom
To avoid low or distorted sound, and to provide
clear and crisp telephone calls, the microphone
should be positioned within 30-40mm of your
mouth (2 ngers width). The microphone boom
arm will move in a variety of directions to ensure
the best t. See g.5.
30 - 40mm
from mouth
(2 ngers width)
Adjusting the Headband
Place the headset receiver to your ear(s),
if using a single ear headset you should set
the T-bar above your other ear. Adjust the
headband until it is comfortable, ideally
ensuring there is virtually no pressure felt on
the ear(s).
Most headsets can be worn on either side.
To change the microphone side, simply rotate
the microphone boom 180° to the other
side. The microphone boom will not rotate a
complete 360°. See g.3.
Microphone
housing -
120° rotation
Microphone boom
- 280° rotation
The microphone housing/ear cushion can
rotate 120° to enable individual comfort on
ear(s). See g.4.
Removing the Microphone Boom
To remove the microphone boom from the
headband, carefully and gently push inside the
ear cushion on the speaker material for approx.
3mm - 5mm. The microphone housing will
then come away easily. See g.8a & 8b.
DO NOT pull on the
microphone boom
to remove it from the
headband.
14/04/005.V2
NOTE:
Disconnect the Quick Disconnect cable, See g.7,
before separating the microphone boom from
the monaural/binaural headand.
g.7
g.3
g.4
g.5
g.8a
g.8b
To adjust the microphone boom to the shape of
your face, hold the boom arm as shown in g. 6.
Do not hold the microphone end to shape boom.
g.6
Designed and Engineered in the UK
Assembled in China
Contents
Introduction 2
Connecting boom to headband 4
Features 5
Connection to your desk phone 6
Adjustment 7
Notes 9
Warranty 10
Introduction
Thank you for purchasing this product.
Your new headset has been developed using
the latest technology, designed for comfort
and freedom of movement.
This headset is very easy to use and setup,
although to get the best from your new
purchase, we recommend you read this user
guide carefully before using the headset for the
rst time.
Unpacking
Remove your headset from its packaging and
ensure that along with this user guide, you
have the correct specied accessories.
Retain the headset box for storage of your unit,
and also in the unlikely event that it needs to
be returned for servicing or repair.
Compatibility Guide
Please check that you have the correct bottom
cable to connect your new headset to your
desk phone. You can check with your supplier
or visit www.jpltele.com and follow the links in
the compatibility menu.
Warning
Ensure that all electrical connections (including
extension leads and interconnections between
pieces of equipment) are properly made and
in accordance with the relevant manufacturers
instructions.
Do not continue to operate the equipment if you
are in any doubt about it working normally, or if
it is damaged in any way. Disconnect from your
telephone equipment and consult your dealer.
Do not allow electrical equipment to be exposed
to rain or moisture.
Never push anything into holes, slots or any other
opening on your headset as this could result in
fatal electrical shock.
Do not open the headset housing as doing so will
void the warranty.
Never guess or take chances with electrical
equipment.
Telephone headsets are capable of producing
high levels of sound. Prolonged exposure to high
sound levels can cause damage to hearing.
3 4 5
Headset Features
Adjustable Headband
Ear Cushion
Microphone
Clothing Clip
Quick Disconnect
(QD)
Connecting Your Headset
Does your desk phone have a dedicated
headset connection port?
If it does, simply connect your headsets Quick
Disconnect cable to your chosen bottom lead
(not supplied), then connect the bottom lead
to the dedicated port on your desk phone.
If you nd that when the headset is connected
to the phone it is not working as expected then
it is very likely you are using an incompatible
bottom lead. There are various bottom leads
available, these are all designed to connect
your headset to specic brands of desk phone,
ensuring whatever your setup, your headset
will be compatible.
Please contact your dealer to attain the correct
bottom lead for your desk phone.
Note: All bottom leads are supplied as an
accessory at additional cost.
What to do if your desk phone does not
support a dedicated headset connection
port:
Your desk phone requires an external headset
amplier. If you already have a headset
amplier, read through the units setup guide
and connect your headset accordingly.
Using the Quick Disconnect Lead
Your headset may be equipped with a Quick
Disconnect allowing you to move away from
your desk (disconnecting the 2 connectors)
without losing the call.
To separate the 2 connectors, simply make a
straight pull, pulling the lehand connector to
the le and the righthand connector to the right.
DO NOT attempt to bend or leaver the
connectors apart.
In the event that you do not have a headset
amplier, please contact the supplier of this
headset (details found on rear of user guide).
They will be able to provide the correct
amplier for your headset and desk phone.
6
Connecting the Microphone Boom to
the Headband
Gently push the microphone boom into the
headband until it clicks. See g.2a & 2b.
Safety
For your own safety, this product should only be
used with CE ACA and RoHS approved equipment.
Using this headset with non approved equipment
can void this products warranty.
Maintenance
To gain optimal performance, hygiene and lifespan from you headset, replace all consumable
items; - ear foam cushion, microphone foam (if
applicable) and microphone lter every 6 months.
Environmental Notice
This headset has been made to CE, RoHS and
WEEE standards. In the interest of recycling raw
materials, please do not dispose of this headset
in the household waste at the end of its useful
life. Disposal can take place at approved recycling
or disposing locations in accordance with local
regulations.
Bottom Cable
(Not included)
NOTE:
Before connecting the Quick Disconnect cable to
bottom lead, See g.1, make sure the microphone
boom is securely fastened onto the monaural/
binaural headband.
g.1
g.2a
g.2b
Warning: Before connecting the
Quick Disconnect cable, make sure
the microphone boom is securely fastened
onto the monaural/binaural headband!
Also, before separating the microphone
boom from the monaural/binaural headband,
make sure the Quick Disconnect cable is
disconnected from the bottom lead rst!
Loading...