Element ELCP0371 Instruction Manual

This TV incorporates High-Denition Multimedia Interface (HDMITM) technology.
HDMI, the HDMI logo and High-Denition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.

Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Condential unpublished works. © 1992 -1997 Dolby Laboratories, Inc. All rights reserved.

ENGLISHENGLISH

1

FCC

Federal Communications

Commission Statement

This equipment has been tested and found to comply with the limits of a class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

1. Reorient/Relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit which is different from what the receiver is
connected to.

4. Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user authority to operate the
equipment.

2

Warnings and Precautions

Warnings and Precautions

To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture.

This symbol is intended to alert the user to avoid the risk of electric shock.
This equipment must not be disassembled by anyone except qualied service personnel.

This symbol is intended to alert the user to the presence of important operating and
maintenance instructions in the literature accompanying the appliance.

▪ TO REDUCE THE RISK OF ELECTRIC SHOCK,
▪ DO NOT REMOVE COVER (OR BACK).
▪ NO USER-SERVICEABLE PARTS INSIDE.
▪ REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Use of controls, adjustments or performance of procedures other than those specied herein
may result in hazardous radiation exposure.

CAUTION

Important Safety Instructions

To prevent any injuries, the following safety precautions should be observed in the installation, use,
servicing and maintenance of this equipment.
Before operating this equipment, please read this manual completely, and keep it nearby for future
reference.

WARNING

▪ Do not place the equipment on any uneven or unstable carts, stands, tables, shelves etc.

The equipment may fall, causing serious injury to children or adults and serious damage to
the equipment itself.

▪ Use only a cart or stand recommended by the manufacturer. This equipment and

recommended cart or stand should be handled with care. Quick stops, excessive force, and
uneven surfaces may cause the equipment and cart/stand to overturn.

▪ Do not disable the 3-wire grounding type plug. The grounding pin on the 3-prong plug is an

important feature. Removing the grounding pin will increase the risk of damaging the
equipment.

▪ If you can not t the plug into the electrical outlet, contact an electrician to install a grounding

outlet.

▪ Always operate this equipment from the type of power source indicated on the rear of the

serial/model plate.

▪ Never overload wall outlets and extensions.

This symbol indicates caution points.

This symbol indicates actions that should not be done.

This symbol indicates actions that must be performed.

ENGLISHENGLISH

3

Warnings and Precautions

▪ Use and handle the power cord with care. Do not place any heavy objects on the AC

power cord.

▪ Do not pull the AC power cord. Do not handle the AC power cord with a wet hand.

▪ Do not touch the power cord and antenna cable during lightning.
▪ Remove the plug from the wall outlet, if the equipment will not be used for a long period

of time.

▪ Do not place, use or handle this equipment near water.

▪ Never expose the equipment to liquid, rain, or moisture.
Seek for service if any of the above is spilled into the equipment.

▪ Do not expose the equipment to extreme temperature or to direct sunlight, as the

equipment may heat up and suffer damage.

▪ Do not install the equipment near any heat sources such as radiators, heat registers,

stoves, or any other apparatus that might produce heat.

▪ Do not attempt to service the equipment yourself.

▪ Opening and removing the covers may expose you to dangerous voltage or other

hazards and may void your warranty. Refer service to qualied personnel.

▪ Do not place or drop any other objects on top.

▪ Do not insert anything into the ventilation holes of your equipment.
Inserting any metal or ammable objects may result to re or electric shock.

▪ Protect the power cord from being walked on or pinchrd particularly at plugs ,convenience

receptacles, and the point where they exit from the apparatus.

▪ Do not place the equipment on uneven or unstable carts, stands, tables, shelves etc. The

equipment may fall, causing serious injury to children or adults and serious damage to
the equipment itself.

Always place the equipment on the oor or on a surface that is sturdy, level, stable and

strong enough to support the weight of the equipment.

▪ Do not block any ventilating openings. Leave an open space around the equipment.
Never place the equipment :
on a bed, sofa, rug, or any other similar surfaces; too close to drapes/curtains/walls, in a

bookcase, built-in cabinet, or any other similar places that may cause poor ventilation.

▪ Unplug this apparatus during lightning storms or when unused for long periods of time.

▪ Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been admaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.

▪ Always remove the power cord from the outlet before cleaning the equipment.

▪ Never use liquid or aerosol cleaners on the equipment.
Clean only with a soft dry cloth.

▪ Only use attachments/accessories specified by the manufacturer.

4

Warnings and Precautions

Outdoor Antenna Safety Instructions

Antenna lead-in wire

Antenna discharge unit
(NEC section 810-20)

Grounding conductors
(NEC section 810-20)

Ground clamps

Power service grounding
(NEC Art250 part H)

Ground clamps

Electric service
equipment

NEC : National Electrical code

If an outdoor antenna is connected, follow the precautions below:

EXAMPLE OF OUTDOOR ANTENNA GROUNDING

Section 810 of National Electrical Code (NEC) provides information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for
the grounding electrode.

▪ An outdoor antenna should not be located in any area where it could come in contact with

overhead power lines, or any other electric light or power circuits.

▪ When installing an outdoor antenna system, extreme caution should be taken to prevent

contact with power lines. Direct contact with power lines may be fatal and should be avoided
at all costs.

ENGLISHENGLISH

5

TABLE OF CONTENTS

Federal Communications Commission Statement .......................... 1

Warnings and Precautions

Important Safety Instructions ....................................................................................... 2

Antenna Safety Instructions ......................................................................................... 4

Chapter 1 Introducing the LCD TV

Key Features ............................................................................................................... 6

Package Contents ....................................................................................................... 7

Setting Your LCD TV .................................................................................................... 8

Your LCD TV .............................................................................................................. 10

Your Remote Control ................................................................................................. 12

Chapter 2 Installing the LCD TV

Connecting a TV Cable or an Antenna ...................................................................... 14

Connecting a VCR ..................................................................................................... 18

Connecting a Video Camera or Play Station ............................................................. 19

Connecting a DVD Player .......................................................................................... 20

Connecting a Digital TV Cable Box or Digital Satellite Receiver ............................... 22

Connecting an AV Equipment with HDMI Connector ................................................. 23

Connecting an AV Equipment with DVI Connector .................................................... 24

Connecting a PC........................................................................................................ 25

Connecting an Audio Receiver or a Dolby Digital 5.1 Sound System........................ 26

Chapter 3 USING THE FEATURES

Wide Screen Viewing ......................................................................................29

Operating the Menu ........................................................................................30

Setting up the HDTV Function ..........................................................................32

Customizing the VIDEO Settings ......................................................................35

Customizing the AUDIO Settings ......................................................................36

Customizing the SETUP Settings......................................................................37

Using the V-CHIP Settings ...............................................................................39

Using the Parental Settings .............................................................................. 41

Customizing the TV Settings ............................................................................42

Speciction .............................................................................................................. 43

6

Chapter 1 Introducing the LCD TV

Various Audio/Video terminals for external equipment connection

▪ 2 set of composite A/V input terminals
▪ 1 set of S-VIDEO terminals
▪ 2 set of component Video input terminals
▪ 1 VGA/ Audio input terminal
▪ 1 HDMI/Auido input terminal
▪ 1 sets of Audio(L/R) output terminals
▪ 2 SPDIF output terminal (Optical x 1 /Coaxial x 1)
▪ 1 Headphone terminal

The built-in TV tuner to receive HD ATSC

▪ This function allows the reception of HD broadcasting without the addition of a set top

box.

High Definition Multimedia Interface (HDMI)

▪ High Denition Multimedia Interface (HDMI) is a small, user-friendly interconnect that

can carry up to 5 Gbps of combined video and audio in a single cable. This system
eliminates the cost, complexity and confusion of multiple cables used to connect
current A/V systems.

HDTV Component Video Inputs

▪ Offers the best video quality for DVD(480p) and digital set-top-box (HD1080i, 720p)

connections.

3D Digital Noise Reduction

▪ This function can digitally reduce image noise to provide better picture quality.

Film-Mode Detection (3:2 Reverse Pull Down)

▪ This function can automatically detect content derived from lm and adjust the

interlacer’s frame matching to provide a more natural-looking, clearer image of the
moving picture.

Chapter 1
Introducing the LCD TV

Key Features

ENGLISH

7

Chapter 1 Introducing the LCD TV

Make sure all of the above contents are included in the package. If you are missing
any items, please contact the customer service department.

 LCD TV

Make sure all of the following contents are included.

 Power Cord

These items are all you need to set up and operate the LCD TV in its basic conguration.

Package Contents

 Remote Control/
AAA Batteries x 2

 User’s Manual

 Bottom Stand /

Screw Driver and 4 Screws

 Quick Start Guide  Warranty Card

 Remote control Guide Stand Assembly Guide

S.MODE MTS P. MODE

VOL.

CH.

MUTE

INPUT

GUIDE EXIT

INFO MENU

LI

S
T

F
A

V
.C

H

T

I

M

E

R

F

R

E

E

Z

E

P.SIZESLEEPCAPTION

Note: the photos of the accessories are for reference only, the numbers of screws, the color
of the remote control, the type of power cord are variable based on the actual models.

8

Chapter 1 Introducing the LCD TV

Setting Your LCD TV

How to install the TV Stand

Stand

Shipping box

Protective bag

Table

Unit

Stand

Table

Stand

Screw

Follow the instructions below to install the TV stand:

 Open the box, and make sure all necessary parts are in the box. The package

contains the LCD TV, screw(s) and stand.

 Cover an even stable surface with a soft cloth. Place the LCD TV unit face-

down on the cloth. Fit the stand onto the bottom of the LCD TV unit as shown:

 Secure the TV stand to the TV neck using the supplied screw(s).

ENGLISH

9

Chapter 1 Introducing the LCD TV

If you prefer to mount your new Element Electronics TV on a wall instead of attaching it to the
stand, please reference the instructions included in the wall mounting kit (sold separately).

 Remove the screws of the table stand and detach the table stand from the TV.

Soft cloth

 Align the holes on the wall mounting hook units with the corresponding holes on the rear

of the TV and fasten four screws.

Soft cloth

Table stand

How to remove the TV Stand

Soft cloth

Wall mounting hook
unit (supplied with the
wall mount kit)

 To prevent damaging the surface of the LCD TV, place the TV on a soft cloth.

Verify your TV’s model and be sure to use the wall mounting kit specied

for your TV model only. Contract your technician for assistance when
installing the wall mounting kit.

4 screws (supplied
with the wall mount
kit)

10

Chapter 1 Introducing the LCD TV

Do not use caustic cleaners (porcelain, stainless steel, toilet, or oven cleaner
etc.) on the remote, as it may suffer damage.

 Use a supplied antenna cable to connect the VHF/UHF signal to the LCD TV’s ANT. terminal

(refer to page15-17).

 Connect the AC power cord at the back of the TV and connect the power cord to wall outlet.

 Insert the 2 batteries supplied in remote control.

 Connect other an external AV device (refer to page19-27).

Step1 Slide the back cover up to open the

battery compartment of the remote
control.

Step2 Insert two AAA size batteries.

Make sure to match the (+) and
( - ) ends of the batteries with
the (+) and ( - ) ends indicated
in the battery compartment.

Slide the cover back into place.

How to setup the TV

L

R

VIDEO1 IN

VIDEO

Your LCD TV

LED

The LED light indicates when the LCD TV is
activated.

IR

Infrared
Receiver

Front/Right Side View and Controls

HEADPHONE

Connects to the external
headphone for private
listening.

VIDEO1 IN

Connects to the composite
Video and Audio output jacks
on external video equipment.

MENU

Press once to display the OSD (on screen
display), press again to turn the OSD off.

VOLUME+-

Adjusts the volume up and down.
Selects the main-menu item and
change values for items when in the
OSD mode.

Turns the LCD TV on and into standby mode.

CHANNEL▲▼

Scans up and down through channels.
Selects sub-menu item when in the OSD
mode.

INPUT

Chooses from different input signal sources.

ENGLISH

11

Chapter 1 Introducing the LCD TV

HDMI IN

AUDIO

L R

L R L R

L R

L

R

L R

L R

AUDIO

VGA IN

VIDEO2 IN

VIDEO AUDIO

S-VIDEO IN

S-VIDEO AUDIO

YPbPr1 IN

AUDIO OUT

STEREO

DIGITAL

OPTICAL

COAXIAL

TV

CABLE

HDTV

AIR

VHF/UHF IN

Y Pb Pr AUDIO

YPbPr2 IN

Y Pb Pr AUDIO

12

Chapter 1 Introducing the LCD TV

Rear View and Jacks

VGA IN

Connects the PC, or other AV equipment with VGA and
AUDIO(L/R) output jacks.

VIDEO2 IN

Connects to the composite VIDEO and AUDIO(L/R) output jacks on external video equipment.

HDMI IN

Connects the all digital AV equipment with HDMI connector.HDMI supports enhanced,
high-denition video and two-channel digital audio. The AUDIO(L/R) of HDMI IN is for
DVI connection.

S-VIDEO IN

Connects to the S-VIDEO and AUDIO(L/R) output jacks on external
video equipment.

AUDIO OUT-DIGITAL-OPTICAL/COAXIAL

Connects to the OPTICAL AUDIO jack on the digital/standard5.1

VHF/UHF IN-HDTV-AIR

Connects RF input from VHF/UHF antenna or cable to receive
high/standard denition television.

VHF/UHF IN-TV-CABLE

Connects RF input from VHF/UHF antenna or cable.

YPbPr1 IN/YPbPr2 IN

Connects to the DVD player, Digital Set-Top-Box, or other AV
equipment with component(YPbPr) video and audio output jacks.

AC IN

Connects to the AC power cord.

AUDIO OUT-STEREO

Connects to the AUDIO(L/R) input jacks on AV equipment.

Your Remote Control

ENGLISH

13

Chapter 1 Introducing the LCD TV

S.MODE

MTS

P. MODE

VOL.

CH.

MUTE

INPUT

GUIDE EXIT

INFO MENU

LIST

FAV.CH

TIMER

FREEZE

P.SIZESLEEPCAPTION

3

9

2

1

8

12

Turns the LCD TV on and off.

MTS Cycles through the multi-channels TV

sound(MTS) options: SAP/MONO/
STEREO

S.MODE Selects sound effect options: Surround/

Live/Dance/Techno/Classic/Soft/Rock/
Pop/Off.

P.MODE Selects picture mode: Vivid/Hi-Bright/

Cinema/Sport/User

P.SIZE Cycles through Wide mode settings :

NORMAL /FULL/WIDE/ZOOM

CAPTION Cycles through the Closed Caption:

 Anlalog Closed Caption:CC1/CC2/

CC3/CC4/T1/T2/T3/T4/Off

 Digital Closed Caption:Service1/

Service2/Service3/Service4/Service5/
Service6/Off

SLEEP Cycles through the LCD TV sleep timer:

OFF/30/60/90/120 mins

0-9 Select and switch to a channel by using

0-9 buttons.

 In HDTV mode, use with 0-9 and 

buttons to select a digital channels.

JUMP Returns to previously selected channel.

MUTE Mutes and restores the audio

VOL.+- Increases and decreases volume.

CH.+- Scans up and down the channels

1

2

2

3

4

5

6

7

8

9

10

11

12

4

5

6

7

10

11

3

9

2

1

8

12

4

5

6

7

10

11

Effective range:
The remote can control the LCD TV from up to 5m away, if pointed directly at the receiver.

14

Chapter 2 Installing the LCD TV

Main
TV(CABLE/AIR) 
HDTV (CABLE/AIR)
VIDEO1 (SIDE)
VIDEO2 (REAR)
VIDEO3 (S-VIDEO)
VIDEO4 (YPbPr1)
VIDEO5 (YPbPr2)
VIDEO6 (HDMI)
COMPUTER (VGA)

S.MODE

MTS

P. MODE

VOL.

CH.

MUTE

INPUT

GUIDE EXIT

INFO MENU

LIST

FAV.CH

TIMER

FREEZE

P.SIZESLEEPCAPTION

13

14

15

16

17

18

19

20

21

22

23

GUIDE Displays the Program Guide on the

screen. Pressing again to turn GUIDE off.

EXIT Exits the OSD menu.

▲▼►◄

Cycles through OSD options and

OK selects individual menu items.

OK conrms option settings.

INFO Pressing repeatedly displays a variety of

information such as the current channel
and the input source.

MENU Displays the OSD menu on the screen.

GREEN No function.

RED No function.

YELLOW No function.

BLUE No function.

LIST Displays the received channel list

INPUT Pressing INPUT displays the source list,

use ▲▼ to select the video equipment
connected to the video inputs of your
LCD TV : TV/HDTV/VIDEO1/VIDEO2/
VIDEO3/VIDEO4/VIDEO5/VIDEO6/
COMPUTER

FAV.CH Pressing FAV.CH display favorite channels.

FREEZE In TV mode, pressing FREEZE to freeze

the current picture, press again to restore
the picture.

TIMER Displays the current time on the screen.

16

14

13

17

15

18

22

25

24

20

19

26

23

21

24

25

26

ENGLISH

15

Chapter 2 Installing the LCD TV

Chapter 2
Installing the LCD TV

Refer to the owner’s manual of any external equipment to be connected.
When connecting any external equipment, do not connect any AC power cords to wall outlets
until all other connections are completed.

Antenna Connection

The antenna requirements for good color TV reception are more important than those for a black &
white TV reception. For this reason, a good quality outdoor antenna is strongly recommended.
The following is a brief explanation of the type of connection that is provided with the various antenna
systems.

75-ohm coaxial cable (round)

F-type connector

300-ohm twin-lead cable (flat)

■ A 75-ohm system is generally a round cable (not included) with F­type connector that can easily be attached to a terminal without
tools.

■ A 300-ohm system is a flat twin-lead cable (not included) that can
be attached to a 75-ohm terminal through a 300-75-ohm adapter
(not included).

Connecting a TV Cable or an Antenna

16

Chapter 2 Installing the LCD TV

OUT

IN

300-ohm twin­lead cable

300-ohm twin­lead cable

75-ohm
coaxial cable

UHF
Antenna

VHF
Antenna

Combiner
(not included)

A. Combination VHF/UHF antenna

300-ohm twin­lead cable

75-ohm
coaxial cable

VHF/UHF
Antenna

VHF/UHF
Antenna

300/75-ohm adapter
(not included)

B. Separate VHF and/or UHF antennas

Use one of the following two diagrams when connecting an outdoor antenna.
A: Shows how to use a VHF/UHF combination outdoor antenna.
B: Shows how to use a separate VHF and/or UHF outdoor antenna.

ENGLISH

17

Chapter 2 Installing the LCD TV

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the
National Electrical Code (NEC) that provides guidelines for proper grounding and, in particular,
species that the cable ground shall be connected to the grounding system of the building
accurately, or as close to the point of cable entry as possible. Use of this TV for other than
private viewing of programs broadcasted on UHF, VHF or transmitted by cable companies for
the use of the general public may require authorization from the broadcast/cable company, and/
or program owner.

A
IN
B

OU T

Cable TV Line

2 set signal
splitter
(not included)

RF switch
(not included)

Cable TV converter/
descrambler
(not included)

Cable TV (CATV) Connection

■

The RF switch (not included) is required to provide two inputs (A and B). Setting

the RF switch to position A allows viewing of all unscrambled channels by using
the TV channel keys.

■ Setting the RF switch to position B allows viewing of all scrambled channels via
the converter/descrambler by using the converter channel keys.

■ A 75-ohm coaxial cable connector is built into the set for easy hookup.
When connecting the 75-ohm coaxial cable to the set, connect the 75-

ohm cable into the ANT. terminal.

■ Some cable TV companies offer premium pay channels. Since the
signals of these premium pay channels are scrambled, a cable TV
converter/descrambler is generally provided to the subscriber by the
cable TV company.

This converter/descrambler is necessary for normal viewing of scrambled channels.
(Set your TV to channel 3 or 4, typically one of these channels is used. If this is unknown,
consult your cable TV company.)
For more specic instructions on installing cable TV, consult your cable TV company.
One possible method of connecting the coverter/descrambler provided by your cable TV
company is shown in the diagram below.

VHF/UHF IN

18

Chapter 2 Installing the LCD TV

 METHOD A:

Use a supplied antenna cable to connect the NTSC signal to the LCD TV’s TV CABLE

terminal.

METHOD B:

Use a supplied antenna cable to connect the ATSC signal to the LCD TV’s

HDTV AIR terminal.

 Connect the AC power cord at the back of the TV and connect the power cord to wall

outlet.

 Press the button on the remote to turn on the LCD TV.

Always disconnect the LCD TV from the main voltage when the LCD TV will
not be used for a long period of time. The POWER button on the front panel
is only used for switching the LCD TV into standby, it does not disconnect
the device from the main voltage. To completely disconnect the main
voltage, please remove the power plug from the socket.

 Press the Input button on the remote to

display the Input List. Use the ▲► buttons to
select TV( METHOD A), or HDTV (METHOD
B), and press the OK button.

TV

CABLE

HDTV

AIR

VHF/UHF IN

A

B

TV

CABLE

HDTV

AIR

VHF/UHF IN

Main
TV(CABLE/AIR) 
HDTV (CABLE/AIR)
VIDEO1 (SIDE)
VIDEO2 (REAR)
VIDEO3 (S-VIDEO)
VIDEO4 (YPbPr1)
VIDEO5 (YPbPr2)
VIDEO6 (HDMI)
COMPUTER (VGA)

A B

HDMI IN

AUDIO

L R

L R L R

L R

L

R

L R

L R

AUDIO

VGA IN

VIDEO2 IN

VIDEO AUDIO

S-VIDEO IN

S-VIDEO AUDIO

YPbPr1 IN

AUDIO OUT

STEREO

DIGITAL

OPTICAL

COAXIAL

TV

CABLE

HDTV

AIR

VHF/UHF IN

Y Pb Pr AUDIO

YPbPr2 IN

Y Pb Pr AUDIO

Rear of TV

AUDIO Cable

S-VIDEO Cable

AV Cable

ENGLISH

19

Chapter 2 Installing the LCD TV

 METHOD A:

Use a composite cable to connect the VCR’s composite video/audio jacks to the LCD TV’s

VIDEO2 IN jacks.

METHOD B:

Use an audio cable to connect the VCR’s audio output jacks to the LCD TV’s audio

inputs. Use a S-Video cable to connect the VCR’s s-video output jack to the LCD TV’s
S-VIDEO IN input jack.

 Connect all AC power sources, before turning on the power switch of the LCD TV or

other connected equipment.

 Press the button on the remote to turn on the LCD TV.
 To watch a videotape, press the Input button on the remote to select

VIDEO2( METHOD A), or VIDEO3 (METHOD B).

Connecting a VCR

A

B

HDMI IN

AUDIO

L R

L R L R

L R

L

R

L R

L R

AUDIO

VGA IN

VIDEO2 IN

VIDEO AUDIO

S-VIDEO IN

S-VIDEO AUDIO

YPbPr1 IN

AUDIO OUT

STEREO

DIGITAL

OPTICAL

COAXIAL

TV

CABLE

HDTV

AIR

VHF/UHF IN

Y Pb Pr AUDIO

YPbPr2 IN

Y Pb Pr AUDIO

Rear of TV

L

R

VIDEO1 IN

VIDEO

AUDIO

Right Side

or

AUDIO Cable

S-VIDEO Cable

AV Cable

20

Chapter 2 Installing the LCD TV

 METHOD A:

Use a composite cable to connect the video camera’s or play station’s composite video/

audio jacks to the LCD TV’s VIDEO2 IN jacks or VIDEO1 IN jacks.

METHOD B:

Use an audio cable to connect the video camera’s or play station’s audio output jacks to

the LCD TV’s audio inputs. Use a S-Video cable to connect the video camera’s or play
station’s s-video output jack to the LCD TV’s S-VIDEO IN input jack.

 Connect all AC power sources, before turning on the power switch of the LCD TV or

other connected equipment.

 Press the button on the remote to turn on the LCD TV.
 To watch a video vis camera or play station, press the Input button on the remote to

select VIDEO2/VIDEO1( METHOD A), or VIDEO3 (METHOD B).

Connecting a Video Camera or Play Station

Not all cameras have the ability to connect to a TV. Please check your video camera
user guide for compatibility.

PLAY STATION

C

Rear of TV

A

B

HDMI IN

AUDIO

L R

L R L R

L R

L

R

L R

L R

AUDIO

VGA IN

VIDEO2 IN

VIDEO AUDIO

S-VIDEO IN

S-VIDEO AUDIO

YPbPr1 IN

AUDIO OUT

STEREO

DIGITAL

OPTICAL

COAXIAL

TV

CABLE

HDTV

AIR

VHF/UHF IN

Y Pb Pr AUDIO

YPbPr2 IN

Y Pb Pr AUDIO

or

ENGLISH

21

Chapter 2 Installing the LCD TV

 METHOD A:

Use a composite cable to connect the DVD player’s composite video/audio jacks to the LCD

TV’s VIDEO2 IN jacks.

METHOD B:
Use an audio cable to connect the DVD player’s audio output jacks to the LCD TV’s

audio inputs. Use a S-Video cable to connect the DVD player’s s-video output jack to the
LCD TV’s S-VIDEO IN input jack.

METHOD C:
Use a component cable to connect the DVD player’s component output jacks to the LCD TV’s

YPbPr1 IN or YPbPr2 IN input jacks.

Use an audio cable to connect the DVD player’s component audio jacks to the LCD TV’s

audio input jacks.

DV D PL AYE R

PrPb

PrPb

Connecting a DVD Player

The component video jacks on your DVD player are sometimes labeled
YPbPr, or YCbCr. For an explanation of component video, see your DVD
player’s user guide.

AUDIO Cable

S-VIDEO Cable

AV Cable

COMPONENT/AUDIO Cable

22

Chapter 2 Installing the LCD TV

For best picture quality, if your equipment has component video output, use
a component cable instead of a composite video or S-video cable.

 Connect all AC power sources, before turning on the power switch of the LCD TV or

other connected equipment.

 Press the button on the remote to turn on the LCD TV.
 To watch a DVD, press the Input button on the remote to select

VIDEO2( METHOD A), or VIDEO3 ( METHOD B), or VIDEO4/VIDEO5 (METHOD C).

ENGLISH

23

Chapter 2 Installing the LCD TV

 Use a component cable to connect the satellite receiver’s/TV Cable Box’s component

(YPbPr1) output jacks to the LCD TV’s component input jacks.

Use an audio cable to connect the satellite receiver’s/TV Cable Box’s component audio

jacks to the LCD TV’s audio input jacks.

 Connect all AC power sources, before turning on the power switch of the LCD TV or

other connected equipment.

 Press the button on the remote to turn on the LCD TV.

 To watch programs via satellite receiver or TV Cable Box, press the Input button on the

remote to select VIDEO4/VIDEO5.

Rear of TV

HDMI IN

AUDIO

L R

L R L R

L R

L

R

L R

L R

AUDIO

VGA IN

VIDEO2 IN

VIDEO AUDIO

S-VIDEO IN

S-VIDEO AUDIO

YPbPr1 IN

AUDIO OUT

STEREO

DIGITAL

OPTICAL

COAXIAL

TV

CABLE

HDTV

AIR

VHF/UHF IN

Y Pb Pr AUDIO

YPbPr2 IN

Y Pb Pr AUDIO

or

PrPb

PrPb

Connecting a Digital TV Cable Box or Digital Satellite Receiver

COMPONENT/AUDIO Cable

24

Chapter 2 Installing the LCD TV

HDMI IN

AUDIO

L R

L R L R

L R

L

R

L R

L R

AUDIO

VGA IN

VIDEO2 IN

VIDEO AUDIO

S-VIDEO IN

S-VIDEO AUDIO

YPbPr1 IN

AUDIO OUT

STEREO

DIGITAL

OPTICAL

COAXIAL

TV

CABLE

HDTV

AIR

VHF/UHF IN

Y Pb Pr AUDIO

YPbPr2 IN

Y Pb Pr AUDIO

Rear of TV

 Use a HDMI cable to connect the AV equipment’s HDMI output jack to the LCD TV’s HDMI IN

jacks.

 Connect all AC power sources, before turning on the power switch of the LCD TV or

other connected equipment.

 Press the button on the remote to turn on the LCD TV.
 Press the Input button on the remote to select VIDEO6.

Connecting an AV Equipment with HDMI Connector

The HDMI connector provides both video and audio signals, it’s not
necessary to connect the audio cable.

HDMI Cable

AV EQUIPMENT

ENGLISH

25

Chapter 2 Installing the LCD TV

HDMI IN

AUDIO

L R

L R L R

L R

L

R

L R

L R

AUDIO

VGA IN

VIDEO2 IN

VIDEO AUDIO

S-VIDEO IN

S-VIDEO AUDIO

YPbPr1 IN

AUDIO OUT

STEREO

DIGITAL

OPTICAL

COAXIAL

TV

CABLE

HDTV

AIR

VHF/UHF IN

Y Pb Pr AUDIO

YPbPr2 IN

Y Pb Pr AUDIO

Rear of TV

 Use a HDMI-to-DVI cable to connect the AV equipment’s DVI output jack to the LCD TV’s

HDMI IN jacks.

Use an audio cable to connect the AV equipment’s audio output jacks to LCD TV’s HDMI

AUDIO jacks.

 Connect all AC power sources, before turning on the power switch of the LCD TV or

other connected equipment.

 Press the button on the remote to turn on the LCD TV.
 Press the Input button on the remote to select VIDEO6.

Connecting an AV Equipment with DVI Connector

If the LCD TV is connected to AV equipment’s DVI connector, you will need
an HDMI-to-DVI cable or an HDMI adapter(not suplied).

AV EQUIPMENT

HDMI-to-DVI Cable

AUDIO Cable

DVI IN

AUDIO

L R

26

Chapter 3 Using the LCD TV

 Use a D-SUB cable to connect the PC’s D-SUB output jack to the LCD TV’s VGA input

jack. Use an audio cable to connect the PC’s audio output jacks to LCD TV’s.

 Connect all AC power sources, before turning on the power switch of the LCD TV or

other connected equipment.

 Press the button on the remote to turn on the LCD TV.
 Press the Input button on the remote to select COMPUTER.

HDMI IN

AUDIO

L R

L R L R

L R

L

R

L R

L R

AUDIO

VGA IN

VIDEO2 IN

VIDEO AUDIO

S-VIDEO IN

S-VIDEO AUDIO

YPbPr1 IN

AUDIO OUT

STEREO

DIGITAL

OPTICAL

COAXIAL

TV

CABLE

HDTV

AIR

VHF/UHF IN

Y Pb Pr AUDIO

YPbPr2 IN

Y Pb Pr AUDIO

Rear of TV

Connecting a PC

VGA Cable

AUDIO Cable

PC

Audio Receiver

Audio Amplifier

AB

ENGLISH

27

Chapter 3 Using the LCD TV

 Connecting to Audio Receiver:

Use an audio cable to connect the audio receiver’s audio LINE IN jacks to LCD TV’s

AUDIO OUT jacks.

 Connecting to Digital 5.1 Sound System:

METHOD A:
Use an optical cable to connect the audio amplier’s OPTICAL IN jacks to LCD TV’s

OPTICAL OUT jacks.

METHOD B:

Use a coaxial cable to connect the audio amplier’s COAXIAL IN jacks to LCD TV’s

COAXIAL OUT jacks.

Note: Above mentioned function is only available under HDTV (cable/air) mode.

 Connect all AC power sources, before turning on the power switch of the LCD TV or

other connected equipment.

 Press the button on the remote to turn on the LCD TV.

HDMI IN

AUDIO

L R

L R L R

L R

L

R

L R

L R

AUDIO

VGA IN

VIDEO2 IN

VIDEO AUDIO

S-VIDEO IN

S-VIDEO AUDIO

YPbPr1 IN

AUDIO OUT

STEREO

DIGITAL

OPTICAL

COAXIAL

TV

CABLE

HDTV

AIR

VHF/UHF IN

Y Pb Pr AUDIO

YPbPr2 IN

Y Pb Pr AUDIO

Connecting an Audio Receiver or a Dolby Digital 5.1 Sound System

AUDIO Cable

For better sound quality, you may want to play the LCD TV audio through your stereo system.

28

Chapter 3 Using the LCD TV

Chapter 3
USING THE FEATURES

 WIDE

Stretches the image vertically and

horizontally to ll the screen at 1:1.85
aspect ratio.

Wide Screen function allows viewing of 4:3/16:9 images in wide screen mode, cycling through
the following wide screen settings. Press the P.SIZE button repeatedly to select the screen
format you want.

 NORMAL

Displays at 4:3 aspect ratio.

 ZOOM

Stretches the image vertically and

horizontally to ll the screen at 1:2.35
aspect ratio.

Wide Screen Viewing

 FULL

Stretches the image vertically and

horizontally to keeps the image size
consistent in the center of the screen and
stretches the sides

ENGLISH

29

Chapter 3 Using the LCD TV

 Press the button to turn the LCD TV on.
 Press the MENU button on the remote control,the on-screen menu will appear on the

screen. Use the ◄► buttons to select your main menu option.

VIDEO MENU:

AUDIO MENU:

Operating the Menu

Picture Mode Vivid
Contrast 75
Brightness 65
Auto Setting
Phase 20
Manual Clock 128
Display Adjustment
Color Temperature Nature

Video Select Exit

Audio Select Exit

Bass 50
Treble 50
Balance 0
Sound Effect Off

▪ If the signal source is VIDOE/SVIDEO/YPbPr/

HDMI/VGA, the AUDIO MENU appears as:

Audio Select Exit

Bass 50
Treble 50
Balance 0
Sound Effect Off
MTS System Stereo

▪ If the signal source is TV, the AUDIO MENU

appears as:

▪ If the signal source is VGA, the VIDEO MENU

appears as:

Picture Mode Vivid
Contrast 75
Brightness 55
Saturation 62
Hue +22
Sharpness 4
Color Temperature Nature

Video Select Exit

▪ If the signal source is TV/HDTV/VIDOE/SVIDEO/

YPbPr/HDMI, the VIDEO MENU appears as:

Allows you to make adjustments to your picture settings.

Allows you to customize the audio options and effects.

Audio Select Exit

Bass 50
Treble 50
Balance 0
Sound Effect Off

▪ If the signal source is HDTV, the AUDIO MENU appears as:

30

Chapter 3 Using the LCD TV

 Use the ▲▼ buttons to select an option of the sub-menu, and press the OK button. While in

adjustment mode, and use the ◄► buttons to change the value of the item.

 Press the MENU button to exit the menu.

SETUP MENU:

Setup Select Exit

Language English
Timer 15
Closed Caption off
V-Chip
Parental
Default

TV MENU:

Searching
Tuner Mode Cable-STD
Channel Skip On
Channel Name

TV Select Exit

HDTV MENU:

HDTV Select Exit

Audio Language ◄ English ►
Time Zone Eastern Time
SPDIF Type PCM
Auto Scan Scan
Manual Scan Press<Enter>
Channel Skip Press<Enter>
Channel Block Press<Enter>
Caption Press<Enter>

Allows you to set up a variety of features: Language, Closed Caption, factory reset, V-Chip, Parental Control
sleep timer.

Allows you to edit and label channels.

Allows you to set up the HDTV program function.

ENGLISH

31

Chapter 3 Using the LCD TV

 With the LCD TV connected to a television programming source, press the TV button

on the remote control.

 Press the MENU button on the remote control to display the Main menu, and use

the ◄► buttons to select the HDTV.

Automatically scans and stores all the TV channels

Setting up the HDTV Function

HDTV Select Exit

Audio Language ◄ English ►
Time Zone Eastern Time
SPDIF Type PCM
Auto Scan Scan
Manual Scan Press<Enter>
Channel Skip Press<Enter>
Channel Block Press<Enter>
Caption Press<Enter>

 Press the OK button to display the received channel list, then press ▲▼the buttons to

select a channel. Or, use the ▪ (Input button) with 0-9 buttons to select digital channel( for

example 9.1)

 Press the ▼ button to select Auto Scan, and press the OK button. The Auto Scan

automatically creates a list of receivable channels. Press the MENU button at any time to
interrupt the memorization process.(the list cannot be created if interrupted)

HDTV Cancel

Status: Scanning..
Channels Found: 2

Channel List

9-1 KQED-HD

9-2 KOED-SD

The digital main channel might include many subchannels (for example
9-1, 9-2..) that are showing program at the same time.

32

Chapter 3 Using the LCD TV

 The HDTV menu includes the following options:

Audio Language Allows to select the audio language:

English/Spanish/French.

Time Zone Allows selection of regional TV systems of USA: Eastern Time/Indiana/

Central time/Mountain Time/Arizona/Pacic Time/Alaska/Hawaii

SPDIF Type Allows to selection of the digital sound format: PCM/OFF/Dolby Digital

Auto Scan Automatically sets up channel list on TV for all receivable channels.

Manual Scan Allows to set up TV channel manually.

Channel Skip Allows addition/removal of digital channels.

Channel Block Allows to block digital channels.

Use the Channel Block function, must enter a four-digit password. The

factory password is 0000.

Caption Allows to set closed caption:

HDTV Select Back

Analog Closed Caption ◄ OFF ►
Digital Closed Caption OFF
Caption Style

▪ Analog Closed Caption:
Allows to set basic analog closed caption options:OFF/CC1/CC2/CC3/CC4
▪ Digital Closed Caption:
Allows to set digital closed caption options:Service1/Service2/Service3/
Service4/Service5/Service6/OFF
▪ Caption Style:
Allows to customize the settings for digital closed caption option:

HDTV Select Back

Caption Style ◄ Custom ►
Font Size Large
Font Color White
Font Opacity Solid
Background Color Black
Background Opacity Solid
Window Color Black
Window Opacity Translucent

ENGLISH

33

Chapter 3 Using the LCD TV

 With the LCD TV connected to a television programming source, press the TV button on the

remote control.

 Press the GUIDE button on the remote control, the Program Guide will appear on the

screen:

The Program Guide feature brings all sorts of information provided by the cable TV
company to your screen, such as program title, program duration, time remaining, rating
information, closed caption, availability, etc.

Monday 29 April 2005 2:36:26 PM

9-1 ◄ 9-2 KQED-SD ► 9-1

Today 5:00 PM Calfornia’s Gold CC
Today 5:30 PM Antiques Roadshow
Today 6:00 PM The NewHour with Jim Lehrer CC
Today 7:30 PM Zoboomafoo CC
Today 7:30 PM Arthur
Today 11:00 PM Antiques Roadshow CC

5:00 PM - 5:30 PM Mon, 29 Apr Not Rated
Clubs: Dongwa doesn’t communicate with his parents.
Eplisode: Explorer’s club/Time for everything

9 - 2 KOED-SD

 Press the ▲▼ button to select the program from a list, the Program Guide provides

introduction about the current program being shown on each channel.

Monday 29 April 2005 2:36:26 PM

9-1 ◄ 9-2 KQED-SD ► 9-1

5:00 PM - 5:30 PM Mon, 29 Apr Not Rated
Clubs: Dongwa doesn’t communicate with his parents.
Eplisode: Explorer’s club/Time for everything

9 - 2 KOED-SD

Today 5:00 PM Calfornia’s Gold CC

Today 5:30 PM Antiques Roadshow
Today 6:00 PM The NewHour with Jim Lehrer CC
Today 7:30 PM Zoboomafoo CC
Today 7:30 PM Arthur
Today 11:00 PM Antiques Roadshow CC

Using the Program Guide

 Press the GUIDE button again on the remote control to exit the Program Guide

34

Chapter 3 Using the LCD TV

 Press the button to turn the LCD TV on.
 Press the MENU button on the remote control to display the Main menu, and use the

◄► buttons to select the VIDEO.

 Use the ▲▼buttons to highlight an individual VIDEO option, use the ◄► buttons to

change the setting, and press the MENU to exit the menu

 The VIDEO menu includes the following options:

Picture Mode Cycles among display types: Vivid/Hi-Bright/Cinema/Sport/User

Contrast Controls the difference between the brightest and darkest regions of the

picture.

Brightness Controls the overall brightness of the picture.

Saturation Controls the color intensity.

Hue Controls the difference between the green and red regions of the

picture.

Sharpness Increase this setting to see crisp edges in the picture; decrease it for

soft edges.

Color temperature Adjusts color components independently to achieve a warm or cool

effect: Cool/Middle/Warm/User

▪ Warm: Increases red tint
▪ Nature: Increases natural tint
▪ Cool: Increases blue tint
▪ User: Allows the user to adjust red, green and blue color
component levels independently.

Customizing the VIDEO Settings

Picture Mode Vivid
Contrast 75
Brightness 55
Saturation 62
Hue +22
Sharpness 4
Color Temperature Nature

Video Select Exit

ENGLISH

35

Chapter 3 Using the LCD TV

 Press the button to turn the LCD TV on.
 Press the MENU button on the remote control to display the Main menu, and use the

◄► buttons to select the AUDIO.

 Use the ▲▼buttons to highlight an individual AUDIO option, use the ◄► buttons to

change the setting, and press the MENU to exit the menu

 The AUDIO menu includes the following options:

Bass Controls the relative intensity of lower-pitched sounds.

Treble Controls the relative intensity of higher pitched sounds.

Balance Adjusts the relative volume of the speakers in a multiple speaker

system.

Sound Effect Allows selection of an audio-enhancement technique from among the

following options: Surround/Live/Dance/Techno/Classic/Soft/Rock/POP/
Off.

MTS System Allows you to listen to high-delity stereo sound while watching TV.
▪ Stereo:
Use separate audio tracks for left and right speakers, if available.
▪ SAP:
You can enjoy a second audio program from the speakers while

watching a scene in the original program.

▪ Mono:
Allows mono output (useful when stereo is noisy or inconsistent).

Customizing the AUDIO Settings

Video Select Exit

Bass 50
Treble 50
Balance 0
Sound Effect Off
MTS System Stereo

36

Chapter 3 Using the LCD TV

 Press the button to turn the LCD TV on.
 Press the MENU button on the remote control to display the Main menu, and use the

◄► buttons to select the SETUP.

 Use the ▲▼buttons to highlight an individual SETUP option, use the ◄► buttons to

change the setting, and press the MENU to exit the menu.

 The SETUP menu includes the following options:

Language Selects to display all on-screen menus in your language of choice:

English/French/Spanish.

Timer Allows to set up clock and to program the TV to turn on and off and tune

to a specic channel.

Customizing the SETUP Settings

Video Select Exit

Language English
Timer 15
Closed Caption off
V-Chip
Parental
Default

▪ Time:
Selects to set the current time by hour, minute, second.
▪ Start Time:
Selects to set the time that you want the TV to turn on.
▪ Stop Time:
Selects to set the time that you want the TV to turn off.
▪ Channel:
Selects to set the specic channel that you want the TV to tune.
▪ Activate:
Selects to turn on/off/once the timer.
▪ Confirm:
Selects to conrm.

ENGLISH

37

Chapter 3 Using the LCD TV

Closed Caption Allows to select from 4 closed caption modes:
▪ CC1 /CC2 /CC3 /CC4:
Display a printed version of the dialog and sound effects of the

program being viewed.

▪ T1/T2:
Display station information presented using either half or the whole

screen.

▪ T3/T4:
Extended Data Services. For example: Network name, program

name, program length, etc.

V-Chip Allows to setup the TV and MPAA Rating Lock options (refer to “Using the

V-CHIP Setting”).

Parental Allows to setup the Parental Lock options.

Default Restores factory settings.

38

Chapter 3 Using the LCD TV

 Use the V-CHIP function, must enter a four-digit password. The factory password is

0000.

The US has 2 rating system for viewing content: Movie blocking(MPAA) and TV Blocking.
The TV Blocking conjuncts with the V-CHIP to help parents block inappropriate programs from their
children.
The Movie blocking(MPAA) is used for original movies rated by the Motion Picture Association of
America(MPAA) as broadcasted on cable TV and not edited for television.
The V-CHIP can also be set to block MPAA-rated movies.

 Use the ▼ button to select the V-Chip, and press the OK to display the V-Chip menu.

 The MPAA includes the following options:

RATING DESCRIPTION

G General Audiences. Movie is appropriate for all ages.

PG Parental Guidance Suggested. May contain material not suited for younger

viewers

PG-13 Contains content that may not be appropriate for viewers under the age of 13.

R Restricted. Contains adult content, no one under 17 admitted without parent.

NC-17 No one 17 and under admitted.

X No one 17 and under admitted.

Use the ▲▼ buttons to select the rating you want and press the OK button repeatedly to select

BLOCK() or UNBLOCK().

Using the V-CHIP Settings

Setup Select Exit

Block MPAA Rating
Block TV Rating
Block MPAA Unrated No
Block TV None Rating No

Inout Your Password Please

* * * *

OK Cancel

ENGLISH

39

Chapter 3 Using the LCD TV

CONTENT-BASED

FV D L S V

AGE-BASED

TV-Y

TV-Y7



TV-G

TV-PG

   

TV-14

   

TV-MA

  

 : To block programs by both content and age.

 The TV GUIDELINE has 2 rating methods: Content-Based Rating and Age-Based Rating.

The

TV GUIDELINE includes the following options:

Use the ▲▼ buttons to select the rating you want and press the OK button repeatedly to select

BLOCK() or UNBLOCK().

 The V-CHIP menu includes the following options:

Block MPAA Rating Selects to activate the MPAA Rating programs

Block TV Rating Selects to activate the TV Rating programs.

Block MPAA Unrated ▪ YES:

Block all movies that are broadcast without a MPAA rating.
▪ NO:
Allows all movies that are broadcast without a MPAA rating

Block TV None Rating ▪ YES:
Block all movies that are broadcast without a TV rating.
▪ NO:
Allows all movies that are broadcast without a TV rating.

AGE-BASED

RATING DESCRIPTION

TV-Y All children

TV-Y7 Directed to children age 7 and older

TV-G General Audience

TV-PG Parental Guidance suggested

TV-14 Parents strongly cautioned

TV-MA Mature Audience only

CONTENT-BASED

RATING DESCRIPTION

FV Fantasy violence
D Suggestive dialogue
L Strong language
S Sexual situations
V Violence

40

Chapter 3 Using the LCD TV

The Parental blocking can be set up to the TV to block a Channel or a Video Source.

 Use the ▼ button to select the Parental, and press the OK to display the Parental

menu.

Using the Parental Settings

Setup Select Exit

Channel Lock 1
Video Lock VIDEO5(YPbPr2)
Change Password

 Use the V-CHIP function, must enter a four-digit password. The factory password is

0000.

You need your password for any future access into the V-Chip and
Parental Setting,

 The Parental menu includes the following options:

Channel Lock Selects to block a TV channel.

Video Lock Selects to block a Input source signal.

Change Password Selects to change your password.

Inout Your Password Please

* * * *

OK Cancel

ENGLISH

41

Chapter 3 Using the LCD TV

 Press the button to turn the LCD TV on.
 Press the MENU button on the remote control to display the Main menu, and use the

◄► buttons to select the TV.

 Use the ▲▼buttons to highlight an individual TV option, use the ◄► buttons

changes the setting, and press the MENU exits the menu.

 The TV menu includes the following options:

Searching Automatically sets up channel list on TV for all receivable channels.

Tuner Mode Allows selection between CATV cable and antenna signal sources:

▪ ANTENNA
Choose this setting if you are receiving TV channels with an antenna

cable.

▪ CABLE STD/CABLE IRC/CABLE HRC
Choose this setting if you are receiving TV channels with a CATV

cable.

Channel Skip Allows addition/removal of channels on the channel list.

Channel Name Allows channel labels to be edited.

Customizing the TV Settings

Searching
Tuner Mode Cable-STD
Channel Skip On
Channel Name

TV Select Exit

42

Specifications

SPECIFICATIONS

LCD Panel Panel Size 37’’ TFT LCD

Brightness 500

Contrast Ratio 1000:1

Max. Resolution 1366x768

Input Connector VIDEO/AUDIO(L/R) 2

S-VIDEO/AUDIO(L/R) 1

YPbPr/AUDIO(L/R) 2

VGA/AUDIO(L/R) 1

HDMI/AUDIO(L/R) 1

AUDIO OUT(L/R) 1

OPTICAL/COAXIAL 1

HEADPHONE 1

Power Source 100-240V~, 50/60HZ,3A

Power Consumption 275 W, standby < 3 W

Dimension 36.6 w x 28.6 h x 10.6 d inch

WEIGHT 40 LB