Electro-Voice P2000 User Manual

P2000
Precision Series Power Amplifier
560 watts per channel at 8 ohms, 900 watts per channel at 4 ohms, 1,200 watts per channel at 2 ohms
Neutrik Speakon® output connectors allow use of heavy-gauge speaker wire for low-loss connections
Extremely low (<0.01%) dynamic distortion ensures excellent sound quality
Three-year parts-and-labor warranty
TM
SPECIFICATIONS Conditions:
1. 0 dBu = 0.775 V rms.
2. Dual-mode ratings are for each channel, both operating, unless noted.
3. 120-volt ac line voltage maintained throughout testing.
Continuous Rated Output Power (20­20,000 Hz at less than 0.1% THD, both channels driven per EIA RS-490),
Dual Mode, 2 Ohms:
1,000 watts
Bridged Mode, 4 Ohms:
2,000 watts
Dual Mode, 4 Ohms:
800 watts
Bridged Mode, 8 Ohms:
1,600 watts
Dual Mode, 8 Ohms:
500 watts
Continuous Rated Output Power (1 kHz, 1% THD, both channels driven per EIA RS-490),
Dual Mode, 2 Ohms:
1,200 watts
Bridged Mode, 4 Ohms:
2,400 watts
Dual Mode, 4 Ohms:
900 watts
Bridged Mode, 8 Ohms:
1,800 watts
Dual Mode, 8 Ohms:
560 watts
Power Bandwidth (+0, –1 dB, reference 1 kHz), Any Mode, 4 Ohms:
10-30,000 Hz
Frequency Response (+0, –3 dB, reference 1 kHz/1 watt):
<10-30,000 Hz
Voltage Gain, 1 kHz, Any Mode, Constant­Gain Option:
26 dB
Input Sensitivity, 1 kHz, Dual Mode for 800 Watts into 4 Ohms:
0 dBu (775 mV)
Maximum Input Level (reference 1 kHz):
+20 dBu (7.75 V)
Input Impedance (per channel, 20-20,000 Hz), Balanced:
20 kilohms
Phase Response (at rated power, any mode, 10-30,000 Hz):
±22.5 degrees
THD Plus Noise at 1 kHz (at rated power, measurement bandwidth 80 kHz):
<0.01%
IMD (SMPTE) (60 Hz/7 kHz, typical, at rated power; see Figure 2):
<0.01%
DIM 30 (composite square-sine wave band-limited to 30,000 Hz):
<0.01%
DIM 100 (composite square-sine wave band-limited to 100,000 Hz):
<0.01%
Rise Time (10% to 90% at rated power, any mode):
<2.5 microseconds
Slew Rate, Any Mode:
>35 V/microsecond
Damping Factor, Any Mode:
>300
Amplifier Protection:
Excessive output voltage; shorted loads; excessive phase shift; rf interference; overtemperature; excessive back EMF; In-rush current limiter
__________________
1. Configured for constant-gain option, all Precision Series amplifiers, regardless of power rating, have a maximum voltage gain of 26 dB.
1
Load Protection:
Start-up/shutdown transients; dc fault; infrasonic signals; low ac line voltage; nonlinear signal limiter
Output Topology:
True complementary symmetry with ungrounded collectors (no mica insulators means better heat transfer)
Output Devices,
Total Number: 32 devices Pd(max) Rating: 250 watts Ic (collector current): 20 amps dc Tj(max): 200 °C (392 °F)
Controls and Switches,
Rear:
Hi-Lo-Cut Filter(On/Off); Bridged Mode switch (Bridged/Normal); Limiter mode (Fast/Slow); Circuit To Chassis Switch (Grounded/Ungrounded); Input Routing (Parallel Mono or Dual Stereo)
Front:
Two calibrated input level controls; power switch
Front-Panel Indicators:
Five LED’s per channel (10 total) for power on, input signal, output signal, limiter on and protect on
Connections,
Input:
3-pin female XLR-type connectors for each channel in parallel with a 3-pin male XLR-type output connector for easy signal routing; the XLR connec­tors are wired according to the IEC 268 standard: pin 1 shield, pin 2 positive, pin 3 negative
Output:
Neutrik Speakon® NL4MP for channels
TM
A, B and for bridged mode
Power:
12-gauge, 3-wire, permanently attached power cable; no ac plug supplied
P2000 SPECIFICATION GRAPHICS
FIGURE 1 — P2000 Dimensions FIGURE 2 — P2000 Intermodulation Distortion
(SMPTE 60 Hz/7 kHz) vs. Power
FIGURE 3 — P2000 Front and Rear Panel
Loading...
+ 2 hidden pages