Beschreibung
P-Amps, ein modulares Endstufen-Konzept. Die flexible Lösung für alle Anwendungen im mobilen Einsatz und für Festinstallationen. Die modulare Architektur der P-Amps erlaubt die flexible Auswahl an Filter- / Signalprozessor sowie Eingangsund Ausgangsmodulen. Damit können die Endstufen leicht und vor allen Dingen zukunftssicher unterschiedlichen Einsatzzwecken in nahezu beliebiger Anschlußtechnik angepaßt werden. Die P-Amps sind werksseitig mit dem Eingangsmodul I-1 (XLR Eingänge mit Durchschleifbuchsen) und dem Ausgangsmodul O-1 (SPEAKON Buchsen) bestückt. Die Frontslots der P-Amps sind mit Abdeckblenden versehen. Über diese Slots können Filterbzw. Signalprozessor Module in den Signalpfad eingefügt werden. Für viele Electro-Voice Lautsprecher stehen boxenspezifische Module zur Verfügung, die in bezug auf Übertragungsverhalten und Dynamik eine optimale Anpassung bzw. Entzerrung der Lautsprecherkomponenten gewährleisten.
Durch Verwendung der Frontmodule können sehr einfach und kostengünstig hochwertige Mehrwegsysteme aufgebaut werden. Der Verkabelungsaufwand im Komplettsystem wird dabei drastisch reduziert.
Die Endstufen P1201 mit 1x1200W an 4Ohm und P1202 mit 2x600W an 4Ohm vereinen überragende Audio-Performance mit höchster Zuverlässigkeit und Betriebssicherheit.
Ein lückenloses Konzept an Protections schützt nicht nur die Endstufen, sondern auch die angeschlossenen Lautsprecher. Zu diesen Schutzschaltungen gehören dynamische Audio-Limiter, DC/HF-Pro- tections, Back-EMF-Protection, Inrush Current Limiter, Short Circuit Protection, Thermal Brain Circuit und natürlich die Temperaturüberwachung der Endtransistoren und der Netztransformatoren. Über die Softstart-Schaltung werden die Leistungsausgänge über Relais verzögert zugeschaltet.
Die thermische Stabilität wird durch zwei dreistufige Hochleistungslüfter mit sehr niedrigem Geräuschpegel gewährleistet. Die Luftführung ist Front-to-Rear, was den problemlosen Betrieb in großen und schmalen Endstufen-Racks ermöglicht.
Comparatorschaltungen vergleichen ständig das Eingangsund das Ausgangssignal der Endstufen und steuern beim Auftreten von nichtlinearen Betriebszuständen die eingebauten Limiter. Sie schützen die angeschlossenen Lautsprecher vor Überlast durch Endstufenclipping. Die Übertragungseigenschaften der P-Amps sind hervorragend. Durch groß dimensionierte Netzteile mit streuarmen Ringkerntransformatoren wird ein großer Headroom weit oberhalb der ausgewiesenen Nennleistung erzielt. In den Endstufen wurde auf die Verwendung von V/I-Foldback - Limiter-Schaltungen verzichtet, so daß der Betrieb an komplexen Lasten bis zu ± 90° Phasenwinkel problemlos möglich ist. Höchste Präzision ist auch in der mechanischen Konstruktion und Verarbeitung gewährleistet. Das robuste Stahlblech-Chassis ist besonders verwindungssteif und auf den harten Tourbetrieb ausgelegt.
Schnelle Auskunft über den Betriebszustand der Endstufen vermittelt das leicht ablesbare LED-Display. Für die beiden Kanäle wird übersichtlich angezeigt, ob Betriebsbereitschaft gegeben ist, ob ein Signal am Ausgang anliegt, wann die Limiter ansprechen und ob eine der Schutzschaltungen aktiv ist. Alle Endstufen der P-Amp Serie können im Normalbetrieb an Lasten bis hinab zu 2 Ohm eingesetzt werden.
Technische Informationen
Architects and engineers specifications
P1201
P1202
MODULAR PRECISION SERIES
Description
P-Amps - a modular power amplifier concept and the most flexible solution for any mobile and permanent installation application. The modular architecture of the P-Amps allows flexible selection of filter/signal processor as well as input and output modules. This provides the possibility to easily include P-Amps power amplifiers into basically any existing and most of all any future application, using principally any connection technique. From the factory, the P-Amps are equipped with an input module I-1 (XLR-type inputs with parallel connectors) and an output module O-1 (SPEAKON-type connectors). The front slots of the P-Amps are covered with blind panels. These slots are meant for including filter or signal processor modules into the signal path. For many Electro-Voice loudspeaker systems cabinet-pertinent modules are available, which in regard to their frequency and dynamic response optimally match the equalization of the loudspeaker components.
The use of front modules makes it easy to establish high quality and yet cost effective multi-way systems while cabling of the entire system is drastically reduced.
The power amplifiers P1201 providing 1 x 1200W into 4 ohms and P1202 providing 2 x 600W into 4 ohms unite outstanding audio performance, highest reliability, and security.
The comprehensive protection concept not only prevents the power amplifiers from being damaged but also the connected loudspeaker systems. This extensive protection circuitry includes dynamic audio limiters, DC/RF protection, Back-EMF protection, inrush current limiter, short circuit protection, thermal brain circuit, and of course the protection against thermal overload of the power transistors and the transformers. During “soft start”, delayed switching the power outputs is performed via relays.
Thermal stability is guaranteed by two extremely low-noise, 3-stage fans. The air circulation is front-to-rear, allowing trouble-free operation even in tall and slim power amplifier rack systems.
The embodied comparators constantly monitor the power amp’s input and output signals, and control the integrated limiters whenever nonlinearity is detected, thus protecting the connected loudspeaker systems against overload and power amplifier clipping. The overall response of the P-Amps is simply extraordinary. Using widely dimensioned power supplies with low-loss toroidal transformers provide additional headroom way above the rated nominal power output capacity. The power amplifiers do not employ V/I-Foldback-Limiters, which allows to drive even complex loads with phase angles of up to ±90° without any problem.
Also the mechanical construction and manufacturing guarantee highest precision. The robust and highly rigid steel chassis is meant to survive the extensive wear of touring applications.
The easily readable LED-display provides quick information about the power amplifier’s operational state. Ready-mode, signal presence, and the activation of limiters or of one of the protection functions are indicated for both channels individually. All P-Amp Series power amplifiers are capable of handling loads down to 2 ohms.
Technical Specifications: P 1201
Amplifier at rated conditions, 8 ohms load, unless otherwise specified.
Load Impedance |
8 ohms |
4 ohms |
2 ohms |
|
Maximum Midband Output Power |
750 W |
1200 W |
1600 W |
|
THD = 1%, 1kHz |
|
|
|
|
Rated Output Power |
500 W |
1000 W |
—— |
|
THD < 0.2%, 20Hz ... 20kHz |
|
|
|
|
Max. Single Channel Output Power |
850 W |
1450 W |
1700 W |
|
Dynamic-Headroom, IHF-A |
|
|
|
|
Maximum RMS Voltage Swing |
|
86V |
|
|
THD = 1%, 1kHz |
|
|
|
|
Voltage Gain |
at 1kHz |
|
33 dB |
|
Slew Rateat 1kHz |
|
40 V/µs |
|
|
Power Consumption |
|
870 W |
|
|
at 1/8 maximum output power @ 4 ohms |
|
|
|
|
Input Sensitivity |
|
1.4 V |
|
|
at rated output power @ 4 ohms, 1kHz |
|
|
|
|
THD at rated output power, |
|
< 0.05 % |
|
|
MBW = 80kHz, 1kHz |
|
|
|
|
IMD-SMPTE |
|
|
< 0.08 % |
|
60Hz, 7kHz |
|
|
|
|
DIM30 |
|
|
< 0.03 % |
|
3.15kHz, 15kHz |
|
|
|
|
Frequency Response |
|
13 Hz ... 45 kHz |
||
-1dB, ref. 1kHz |
|
|
|
|
Power Bandwith |
|
10 Hz ... 50 kHz |
||
THD = 1%, ref. 1kHz, half power @ 4 ohms |
|
|
||
Input Impedance |
|
20 kohms |
|
|
20Hz ... 20kHz, balanced |
|
|
|
|
Damping Factor |
|
> 300 / > 200 |
||
at 100Hz / 1kHz, 8 ohms |
|
|
|
|
Signal to Noise Ratio |
|
106 dB |
|
|
A-weighted, non internal summing mode |
|
|
|
|
Power Requirements |
240V,230V,120V,100V / |
|||
|
50Hz ... 60Hz,factory configured |
|||
Protections |
Audio limiters, High temperature, DC, HF, |
|||
|
Back-EMF, Peak current limiters, |
|
||
|
Inrush current limiters, Turn-on delay |
|
||
Cooling |
|
Front-to-rear, 3-stage-fans |
||
Dimensions (W x H x D), mm |
483 x 132.5 x 426 |
|
||
Weight |
|
17 kg |
|
|
Optional |
|
|
|
|
|
Input transformer |
NRS 90208 (121 641) |
||
|
Rear-rackmount 15,5" |
NRS 90235 (112 733) |
||
|
Rear-rackmount 18" |
NRS 90223 (112 701) |
Technical Specifications: P 1202
Amplifier at rated conditions, both channels driven, 8 ohms loads, unless otherwise specified.
Load Impedance |
8 ohms |
4 ohms |
2 ohms |
|
Maximum Midband Output Power |
2 x 380 W |
2 x 600 W 2 x 850 W |
||
THD = 1%, 1kHz |
|
|
|
|
Rated Output Power |
2 x 250 W |
2 x 500 W |
———— |
|
THD < 0.2%, 20Hz ... 20kHz |
|
|
|
|
Max. Single Channel Output Power |
460 W |
880 W |
950 W |
|
Dynamic-Headroom, IHF-A |
|
|
|
|
Maximum RMS Voltage Swing |
|
64 V |
|
|
THD = 1%, 1kHz |
|
|
|
|
Voltage Gain |
at 1kHz |
|
30 dB |
|
Slew Rate |
at 1kHz |
|
30 V/µs |
|
Power Consumption |
|
870 W |
|
|
at 1/8 maximum output power @ 4 ohms |
|
|
|
|
Input Sensitivity |
|
1,4 V |
|
|
at rated output power @ 4 ohms, 1kHz |
|
|
|
|
THD at rated output power, |
< 0.05 % |
|
||
MBW = 80kHz, 1kHz |
|
|
|
|
IMD-SMPTE |
|
< 0.08 % |
|
|
60Hz, 7kHz |
|
|
|
|
DIM30 |
|
< 0.03 % |
|
|
3.15kHz, 15kHz |
|
|
|
|
Crosstalk Attenuation |
> 80 dB |
|
||
ref. 1kHz, at rated output power |
|
|
|
|
Frequency Response |
13 Hz ... 45 kHz |
|||
-1dB, ref. 1kHz |
|
|
|
|
Power Bandwith |
10 Hz ... 50 kHz |
|||
THD = 1%, ref. 1kHz, half power @ 4 ohms |
|
|
||
Input Impedance |
|
20 kohms |
|
|
20Hz ... 20kHz, balanced |
|
|
|
|
Damping Factor |
|
> 300 / > 200 |
||
at 100Hz / 1kHz, 8 ohms |
|
|
|
|
Signal to Noise Ratio |
106 dB |
|
||
A-weighted |
|
|
|
|
Power Requirements |
240V,230V,120V,100V / |
|||
|
|
50Hz ... 60Hz,factory configured |
||
Protections |
Audio limiters, High temperature, DC, HF, |
|||
|
Back-EMF, Peak current limiters, |
|
||
|
Inrush current limiters, Turn-on delay |
|
||
Cooling |
|
Front-to-rear, 3-stage-fans |
||
Dimensions (W x H x D), mm |
483 x 132.5 x 426 |
|
||
Weight |
|
|
17 kg |
|
Optional |
|
|
|
|
|
Input transformer |
NRS 90208 (121 641) |
||
|
Rear-rackmount 15,5" |
NRS 90235 (112 733) |
||
|
Rear-rackmount 18" |
NRS 90223 (112 701) |