Electro-Voice N868, D868 User Manual

N/D868 User Manual

WIRED

MICROPHONE

The N/D868 is truly a top performer in any application.
Whether in a live sound or studio environment, the
N/D868 is able to handle incredibly high sound pressure
levels without distortion or overriding the input mixer.
With a response specifically designed to kick the
N/D868 can be used as is - no additional EQ required.
Electrovoice was the first to utilize the neodymium
magnet structure, and it remains at the heart of our new
N/DYM series of microphones. Experience the leader
again for the first time and hear the difference.



Designed specifically for kick drum applications in
live or studio environments



Optimized sensitivity for the high sound pressure
levels found in bass drum micing



Extended low-frequency response



No additional EQ required



Rugged steel construction for exceptional durability

Operation

Microphone Use and Placement

Please note that micing techniques are a matter of personal
preference. These are merely guidelines to assist in the
placement of the microphone to gain optimal performance.

Usage Optimal Placement

Kick Drum Remove drum head and damp

with a pillow or blanket.
Position the mic on the pillow
or blanket a few inches in
front of the drum beater. As
an alternative, position the
mic on a small boom stand
with the mic extended into the
drum and at a 90° angel to the
drum beater.

Standard Placement & Use Guidelines

1.

Always point the microphone at the desired source of
sound, and away from any unwanted sources.

The low frequency response of the N/D868 microphone
varies with the distance from the sound source. Known as
proximity effect, maximum bass response is produced
in close-up use with the microphone ¼ inch from the
sound source. Normal bass response is experienced with
working distances greater than 24 inches. Working close
to the microphone will produce a more robust sound.
Close up positioning of the microphone will also reduce
the potential for feedback from the sound reinforcement
system. When , the bass-boost provides an increase in
overall microphone output level. The mixer gain may be
proportionately reduced, resulting in a reduction of the
systems sensitivity to feedback caused by sound entering
the microphone from the loudspeakers.

The microphone should be located close to the

2.

sound source to minimize interference from other
potential sound sources.

Use the 3-to-1 rule when using multiple

3.

microphones. Place each microphone three times
farther from other microphones as from the desired
sound source.

4.

Minimize over-handling of the microphone to reduce
unwanted mechanical noise

5.

Working close to the microphone will increase the
bass tone and also provide increased
gain-before-feedback.

Warranty

N/D 868 Specifications

This product is guaranteed against malfunction from
any cause for two (2) years from the date of original
purchase. In addition, the Limited Warranty for the
acoustic system contained in the microphone shall
apply for the life of this product, defines as a period of
ten (10) years from the date that the manufacture of this
microphone model has been discontinued. Any and all
active electronics incorporated in this microphone are
guaranteed against malfunction due to material
workmanship for a period of three (3) years from the
date of original purchase. This Limited Warranty does
not extend to cables, connectors, or switches.

For warranty service please call us at:

616-695-6831 or
1-800-234-6831

5 dB per division

0

330

300

270

30

60

90

Frequency Response:
Polar Pattern:
Impedance:

..................Cardioid variant

...........150ohms balanced (low-Z)

..............20-10,000 Hz

Sensitivity:

Open Circuit Voltage: ......1mV/Pascal @ 1 kHz

Power Level:(0dB=1mW/pascal) -51.7 dB @1 kHz

Microphone Connector
Equivalent Output Noise

..........3-pin, XLR-type

........17dBAweighted

(0 dB= 0.00002 pascal)

Polarity:

.....Positive pressure on diaphragm causes

positive voltage on pin 2 ref. pin 3

Materials:

Grille screen ....................Memraflex

Finish: ..................Non-reflecting black

Case: ................................Steel

Dimensions:

Length.................@5.22in.(132.6 mm)

Diameter ..................@2.36 in. (60 mm)

Shank....................@1.0in.(25.4mm)

Weight:

Net....................@10.4 oz (295 grams)

Shipping ...............@26.5 oz (750 grams)

Accessories included:

320 stand clamp
Soft zippered gig bag

ä

240

210

180

USA 9600AldrichAve.S.,Minneapolis,MN 55420,Phone: [phone],FAX:[phone]
Canada 705ProgressAvenue,Unit 10,Scarborough,Ontario,Canada,M1H2X1,Phone:[phone],FAX:[phone]
Switzerland Keltenstrasse11, CH-2563IPSACH,Switzerland,Phone:[phone],FAX:[phone]
Germany HirschbergerRing 45,D94302,Straubing,Germany,Phone:[phone],FAX:[phone]
France Parcde Courcerin,AlleeLech Walesa,Lognes,f-77185MarneLa Vallee,France,Phone: [phone],FAX:[phone]
Australia Unit23, SloughBusinessEstate,SilverwaterN.S.W.2128,Australia,Phone:[phone],FAX:[phone]
HongKong UnitE &F, 21/F, Luk Hop IndustrialBldg., 8Luk Hop St.,SanPoK ong,Kowloon,HongKong,Phone: [phone],FAX:[phone]
Japan 2-5-60 Izumi, Suginami-ku,Tokyo, Japan 168,Phone:[phone],FAX:[phone]
Singapore TelexComm PreLtd, 3015AUbi Rd 1,#0510,Kampong UbiIndustrialEstate, Singapore408705,Phone:[phone],FAX:[phone]
Mexico TecnologiaEspecializadaEDD S.A. deC.V.,Av.ParqueChapultepec#66-201,ElParque, Naucalpan,Mexico,DF 53390,Phone:[phone],FAX:[phone]

120

150

N/D868 polar

AVERAGE RESPONSE

N/D868 response

Part Number 535836