Electronics MVP-50T User Manual

Glass Panel Engine MonitorGlass Panel Engine Monitor

Glass Panel Engine Monitor

Glass Panel Engine MonitorGlass Panel Engine Monitor

MVP-50TMVP-50T

MVP-50T

MVP-50TMVP-50T

(for Turboprops and Jets)

Installation InstructionsInstallation Instructions

Installation Instructions

Installation InstructionsInstallation Instructions

II 1211061

You must read this manual before installing or operating the instrument. This manual contains warranty and other information that may affect your decision

to install this product and/or the safety of your aircraft.

Rev. C: 5/2/09

5.55" W x 5.15" H x 2.4" D

Model #:Model #:

Model #:

Model #:Model #:

Electronics International Inc. Electronics International Inc.

Electronics International Inc.

Electronics International Inc. Electronics International Inc.

63296 Powell Butte Hwy • Bend, OR 97701 • (541) 318-6060 • Buy-EI.com 63296 Powell Butte Hwy • Bend, OR 97701 • (541) 318-6060 • Buy-EI.com

63296 Powell Butte Hwy • Bend, OR 97701 • (541) 318-6060 • Buy-EI.com

63296 Powell Butte Hwy • Bend, OR 97701 • (541) 318-6060 • Buy-EI.com 63296 Powell Butte Hwy • Bend, OR 97701 • (541) 318-6060 • Buy-EI.com

S/N:S/N:

S/N:

S/N:S/N:

®®

Important Notice

***** MUST READ *****

Page 1 of 4

If you think it is not important to read this manual, you're wrong!If you think it is not important to read this manual, you're wrong!

If you think it is not important to read this manual, you're wrong! This manual contains

If you think it is not important to read this manual, you're wrong!If you think it is not important to read this manual, you're wrong! important operating information that may affect the safety of the pilot, passengers, aircraft, operation of the system or time to install the system. You MUST read the manual prior to installing this system. Any deviation from these installation instructions is the sole responsibility of the installer and should be done in accordance with AC 43.13.

Read the Warranty/AgreementRead the Warranty/Agreement

Read the Warranty/Agreement. There is information in the Warranty/Agreement that may alter your

Read the Warranty/AgreementRead the Warranty/Agreement decision to install this product. not install this productnot install this product

not install this product. This product may be returned for a refund. Contact Electronics International

not install this productnot install this product inc. for details.

If you are not an FAA Certified Aircraft Mechanic familiar with the issues of installingIf you are not an FAA Certified Aircraft Mechanic familiar with the issues of installing

If you are not an FAA Certified Aircraft Mechanic familiar with the issues of installing

If you are not an FAA Certified Aircraft Mechanic familiar with the issues of installingIf you are not an FAA Certified Aircraft Mechanic familiar with the issues of installing aircraft N1, N2, ITT, Torque, Volt, Amp, Oil Temperature and Pressure instruments, aircraft N1, N2, ITT, Torque, Volt, Amp, Oil Temperature and Pressure instruments,

aircraft N1, N2, ITT, Torque, Volt, Amp, Oil Temperature and Pressure instruments,

aircraft N1, N2, ITT, Torque, Volt, Amp, Oil Temperature and Pressure instruments, aircraft N1, N2, ITT, Torque, Volt, Amp, Oil Temperature and Pressure instruments, Not attempt to install this instrument.Not attempt to install this instrument.

Not attempt to install this instrument.

Not attempt to install this instrument.Not attempt to install this instrument. and practices to install this system (refer to AC 43.13).and practices to install this system (refer to AC 43.13).

and practices to install this system (refer to AC 43.13).

and practices to install this system (refer to AC 43.13).and practices to install this system (refer to AC 43.13).

If you do not accept the terms of the Warranty/Agreement, doIf you do not accept the terms of the Warranty/Agreement, do

If you do not accept the terms of the Warranty/Agreement, do

If you do not accept the terms of the Warranty/Agreement, doIf you do not accept the terms of the Warranty/Agreement, do

DoDo

The installer should use current aircraft standards The installer should use current aircraft standards

The installer should use current aircraft standards

The installer should use current aircraft standards The installer should use current aircraft standards

If the installer does not have the skills, knowledge, tools, equipment or facility, to perform and determine whether the installation of this product is safe, reliable and accurate and to determine whether this product is operating properly after installation, pilot and/or installer are unwilling to take the responsibility for the installation and operation of this product, Electronics International Inc. for details.

By installing this product, the aircraft owner/pilot and installer agree to hold Electronics International Inc. harmless and in no way responsible for monetary compensation, including punitive damages for any incident, harm and/or damage associated with this product. If you do not agree to the above, NOT INSTALL THIS PRODUCT.NOT INSTALL THIS PRODUCT.

NOT INSTALL THIS PRODUCT. This product may be returned for a refund. Contact Electronics

NOT INSTALL THIS PRODUCT.NOT INSTALL THIS PRODUCT. International inc. for details.

Electronics International Inc. is not liable or responsible for a pilot’s action or any situation that results in personal injury, property damage, missed commitments, lack of use of an aircraft or any expenses incurred due to: product failure, inaccuracy in displayed data or text files, display or display format issues, software bugs or problems, upgrade or customization issues, misinterpretation of the display, warning and/or limit settings, calibration problems, installation issues (leaks, mis-wiring, obstructions, damage to aircraft or components, incorrect installation of any parts, wrong parts, parts that don’t fit, etc.) or any other issues related to the installation or operation of this product. All of the above are solely the pilot’s and/or installer’s responsibility. The pilot product before flying the aircraft. The pilot will not allow anyone to operate the aircraft that does not know the operation of this product. The pilot will keep the instrument Operating Instructions in the aircraft at all times. If you do not agree to all of the above, This product may be returned for a refund. Contact Electronics Internaional Inc. for details.

DO NOT INSTALL THIS PRODUCT.DO NOT INSTALL THIS PRODUCT.

DO NOT INSTALL THIS PRODUCT. This product may be returned for a refund. Contact

DO NOT INSTALL THIS PRODUCT.DO NOT INSTALL THIS PRODUCT.

DO NOT INSTALL THIS PRODUCTDO NOT INSTALL THIS PRODUCT

DO NOT INSTALL THIS PRODUCT. If the owner/

DO NOT INSTALL THIS PRODUCTDO NOT INSTALL THIS PRODUCT

DODO

must must

must understand the operation of this

must must

DO NOT INSTALL THIS PRODUCT.DO NOT INSTALL THIS PRODUCT.

DO NOT INSTALL THIS PRODUCT.

DO NOT INSTALL THIS PRODUCT.DO NOT INSTALL THIS PRODUCT.

Important Notice

***** MUST READ *****

Page 2 of 4

Do not install a non-certified MVP-50T (MVP) in a certified aircraft. A certified MVP lists the applicable TSO numbers at the bottom of the Model Label.

Before starting the installation make sure the unit will fit in the location you intend to install it without obstructing the operation of any controls.

Before using the Weight and Balance screen check that the “Weight and Balance Setup” data in the MVP System Configuration Menu is accurate. Always verify the MVP weight and balance data with you aircraft’s POH.

Verify the horsepower displayed on the MVP is accurate, as compared to your aircraft's POH and/or engine TC data.

The MVP must be calibrated to the aircraft fuel system and the MVP's accuracy must be verified before flying the aircraft.

The accuracy and proper operation of each function displayed on the MVP should be verified before the aircraft is released for flight.

When the installation is finished, inspect the system for loose fittings, connections, clamps, probes and inspect for leaks, chafing, obstructions, heat damage and anything that may cause unsafe flight before the 1st run-up, after the 1st run-up and after the first flight.

The MVP allows the pilot to enter checklists, flight plans and general information through the USB port. This data must be verified for its accuracy (by the pilot) before it is used.

Before allowing the aircraft to be flown, verify the instrument markings displayed on the MVP screens are accurate with the aircraft’s POH for every function displayed on the MVP.

Before allowing anyone to operate the aircraft read the Operating Manual including the Important Notice there in. Keep the Operating Instructions in the aircraft at all times.

It is important the password(s) be changed to a unique and protected number before theIt is important the password(s) be changed to a unique and protected number before the

It is important the password(s) be changed to a unique and protected number before the

It is important the password(s) be changed to a unique and protected number before theIt is important the password(s) be changed to a unique and protected number before the first flight.first flight.

first flight. If setup or calibration data is inadvertently or improperly changed, there could be inaccu-

first flight.first flight. rate readings that may lead to improper operation of the aircraft or engine. This could result in engine damage and/or an emergency situation. The password must be protected from dissemination to unauthorized persons.

Important Notice

***** MUST READ *****

Page 3 of 4

Fuel Level Accuracy Limitations:

The accuracy limitations of the MVP are listed below. anyone flying the aircraft aware of these limitations.anyone flying the aircraft aware of these limitations.

anyone flying the aircraft aware of these limitations.

anyone flying the aircraft aware of these limitations.anyone flying the aircraft aware of these limitations.

1. Angle of Attack -1. Angle of Attack -

1. Angle of Attack - The MVP must be calibrated with the aircraft in a cruise angle of attack. If the

1. Angle of Attack -1. Angle of Attack aircraft is in an angle of attack other than cruise, the MVP may display inaccurate fuel levels (depending on the mounting location and type of sensor used). If your aircraft does not sit at a cruise angle of attack when on the ground, it may not display accurate fuel levels. angles of attack to see the affects on the MVP fuel level readings.angles of attack to see the affects on the MVP fuel level readings.

angles of attack to see the affects on the MVP fuel level readings.

angles of attack to see the affects on the MVP fuel level readings.angles of attack to see the affects on the MVP fuel level readings.

Full Fuel Readings -Full Fuel Readings -

Full Fuel Readings - As a tank is filled the fuel sensor may not be able to detect the fuel entering

Full Fuel Readings -Full Fuel Readings the upper corners of the fuel tank. If this is the case with your sensor, the MVP will display lower fuel levels than the actual fuel in the tanks when the tanks are full. When the fuel level drops to a point where the fuel sensor starts to detect a change, the displayed fuel level should be accurate. accuracy of your system by comparing the displayed fuel levels on the MVP to the fuelaccuracy of your system by comparing the displayed fuel levels on the MVP to the fuel

accuracy of your system by comparing the displayed fuel levels on the MVP to the fuel

accuracy of your system by comparing the displayed fuel levels on the MVP to the fuelaccuracy of your system by comparing the displayed fuel levels on the MVP to the fuel levels listed in the flight manual at each fill up.levels listed in the flight manual at each fill up.

levels listed in the flight manual at each fill up.

levels listed in the flight manual at each fill up.levels listed in the flight manual at each fill up.

3. Low Fuel Readings - 3. Low Fuel Readings -

3. Low Fuel Readings -

3. Low Fuel Readings - 3. Low Fuel Readings - for an indicated tank level below 1/8for an indicated tank level below 1/8

for an indicated tank level below 1/8

for an indicated tank level below 1/8for an indicated tank level below 1/8 maintain at least the FAA minimum fuel requirements in the aircraft at all times. mounting location and type of fuel sensor used, the MVP may not be able to accuratelymounting location and type of fuel sensor used, the MVP may not be able to accurately

mounting location and type of fuel sensor used, the MVP may not be able to accurately

mounting location and type of fuel sensor used, the MVP may not be able to accuratelymounting location and type of fuel sensor used, the MVP may not be able to accurately measure the last few gallons of fuel in the tanks.measure the last few gallons of fuel in the tanks.

measure the last few gallons of fuel in the tanks.

measure the last few gallons of fuel in the tanks.measure the last few gallons of fuel in the tanks.

Do not rely on the MVP to determine the fuel level in the tankDo not rely on the MVP to determine the fuel level in the tank

Do not rely on the MVP to determine the fuel level in the tank

Do not rely on the MVP to determine the fuel level in the tankDo not rely on the MVP to determine the fuel level in the tank

. .

. You should always fly the aircraft in such a manner as to

. .

It is the pilot/owner’s obligation to makeIt is the pilot/owner’s obligation to make

It is the pilot/owner’s obligation to make

It is the pilot/owner’s obligation to makeIt is the pilot/owner’s obligation to make

Test your aircraft at differentTest your aircraft at different

Test your aircraft at different

Test your aircraft at differentTest your aircraft at different

Check the Check the

Check the

Check the Check the

Depending on theDepending on the

Depending on the

Depending on theDepending on the

4. Improper Calibration -4. Improper Calibration -

4. Improper Calibration - If the MVP has not been properly calibrated it will not display accurate

4. Improper Calibration -4. Improper Calibration fuel levels in the tanks. It is important you verify the accuracy of the MVP. your measured fuel levels in the tanks with the readings on the MVP before each flight.your measured fuel levels in the tanks with the readings on the MVP before each flight.

your measured fuel levels in the tanks with the readings on the MVP before each flight.

your measured fuel levels in the tanks with the readings on the MVP before each flight.your measured fuel levels in the tanks with the readings on the MVP before each flight.

5. Poor Connections -5. Poor Connections -

5. Poor Connections - Poor connections between the wires leading from the EDC to the fuel

5. Poor Connections -5. Poor Connections sensors can become intermittent with age. An intermittent connection most likely will show up as wandering or inaccurate readings on the MVP. the tanks with the readings on the MVP before each flight.the tanks with the readings on the MVP before each flight.

the tanks with the readings on the MVP before each flight.

the tanks with the readings on the MVP before each flight.the tanks with the readings on the MVP before each flight.

6. Defective Fuel Level Sensors -6. Defective Fuel Level Sensors -

6. Defective Fuel Level Sensors - Fuel sensors can become intermittent or change resistance

6. Defective Fuel Level Sensors -6. Defective Fuel Level Sensors with age. It is not uncommon to find intermittent problems even in new sensors. An intermittent problem with a fuel sensor most likely will show up as wandering or inaccurate readings on the MVP. Always crosscheck the measured fuel levels in the tanks with the readings on the MVP atAlways crosscheck the measured fuel levels in the tanks with the readings on the MVP at

Always crosscheck the measured fuel levels in the tanks with the readings on the MVP at

Always crosscheck the measured fuel levels in the tanks with the readings on the MVP atAlways crosscheck the measured fuel levels in the tanks with the readings on the MVP at each fill up.each fill up.

each fill up.

each fill up.each fill up.

If you ever find an inaccuracy issue or any other problem with a fuel level display on theIf you ever find an inaccuracy issue or any other problem with a fuel level display on the

If you ever find an inaccuracy issue or any other problem with a fuel level display on the

If you ever find an inaccuracy issue or any other problem with a fuel level display on theIf you ever find an inaccuracy issue or any other problem with a fuel level display on the MVP, disable the fuel level display (see the “Redlines, Limits and Color Setup” screen).MVP, disable the fuel level display (see the “Redlines, Limits and Color Setup” screen).

MVP, disable the fuel level display (see the “Redlines, Limits and Color Setup” screen).

MVP, disable the fuel level display (see the “Redlines, Limits and Color Setup” screen).MVP, disable the fuel level display (see the “Redlines, Limits and Color Setup” screen). This will alert anyone flying the aircraft to the condition of this display.This will alert anyone flying the aircraft to the condition of this display.

This will alert anyone flying the aircraft to the condition of this display.

This will alert anyone flying the aircraft to the condition of this display.This will alert anyone flying the aircraft to the condition of this display.

Always crosscheck your measured fuel levels inAlways crosscheck your measured fuel levels in

Always crosscheck your measured fuel levels in

Always crosscheck your measured fuel levels inAlways crosscheck your measured fuel levels in

Always crosscheckAlways crosscheck

Always crosscheck

Always crosscheckAlways crosscheck

Important Notice

***** MUST READ *****

Page 4 of 4

Important Fuel Level Considerations:

DO NOT RELY SOLELY ON THE FUEL LEVEL DISPLAYED ON THE MVP TO DETERMINE THE FUEL LEVELS IN THE AIRCRAFT. The use of the MVP does not eliminate or reduce the necessity for the pilot to use good flight planning, preflight and inflight techniques for managing fuel. It is important the pilot adopt the practices listed below. If

you are not familiar with these techniques, contact the FAA to acquire proper training.

1. A copy of the Operating Manual must be in the aircraft at all times.

2. Flight Planning - Always calculate the fuel requirement for each leg of a flight, including any

alternate plans for bad weather. Keep this information available in the aircraft during the flight. Keep a chart of the published fuel flows for various flight/engine conditions in the aircraft. Keep a chart of the measured fuel flows for various flights in the aircraft. Measured fuel flows can be considerably different from published figures. This usually is due to old, inaccurate engine instruments.

3. Preflight - Do not rely on the MVP to determine the fuel level in the fuel tanks. The pilot must visually check/measure the fuel levels in the tanks before every takeoff.

Crosscheck the measured fuel levels with the displayed levels on the MVP. Also, crosscheck these levels with the fuel requirements for the flight listed in your flight plan.

4. In Flight - Make the MVP part of your normal instrument scan. Crosscheck the fuel levels

displayed on the MVP with your flight plan at each leg of the flight or every 30 minutes

(if a leg is longer than 30 minutes). Calculate the fuel flows from the MVP displayed fuel levels and compare them with your charts of measured and published fuel flows for the aircraft. If there is a discrepancy, land the aircraft at the nearest airport and verify the fuel levels.

Discrepancies should be taken seriously.

5. New Pilot or Owner of the Aircraft - If there is a new pilot or owner of the aircraft, it is

the previous aircraft pilot/owner’s responsibility to insure the new pilot has read this manual and is aware of any accuracy limitations and other important considerations. All limitations and operating characteristics learned from operating the MVP must be passed on to the new pilot/owner.

If you do not agree or are unwilling to comply with the information/requirements contained within this Important Notice, refund. Contact Electronics Internaional Inc. for details.

DO NOT INSTALL THIS PRODUCT.DO NOT INSTALL THIS PRODUCT.

DO NOT INSTALL THIS PRODUCT. This product may be returned for a

DO NOT INSTALL THIS PRODUCT.DO NOT INSTALL THIS PRODUCT.

Contents

(Page 1 of 2)

Warranty/Agreement----------------------------------------------------------------------------------- 1

1.0 System Overview ----------------------------------------------------------------------------------- 3

1.1 System Description --------------------------------------------------------------------------- 5

1.1 MVP Display ----------------------------------------------------------------------------- 5

1.2 EDC-33T --------------------------------------------------------------------------------- 5

1.3 Probes, Transducers and Modules --------------------------------------------------- 5

1.4 Wiring & Extension Cables ----------------------------------------------------------- 6

1.2 Operational Overview ------------------------------------------------------------------------ 6

1.3 Installation Overview ------------------------------------------------------------------------- 6

1.4 Password Protection ---------------------------------------------------------------------------- 7

1.4.1 Level #1 Password (Maintenance): ------------------------------------------------ 7

1.4.2 Level #2 Password (OEM): --------------------------------------------------------- 8

2.0 Hardware Installation ----------------------------------------------------------------------------- 9

2.1 Important Information and Initial Check Out: ------------------------------------------- 11

2.2 Review the "EDC Wiring Work Sheets:" ------------------------------------------------- 12

2.3 Verify you have all the necessary Probes, Modules, Transducers and Cables: ---- 12

2.4 Install the MVP Display: ------------------------------------------------------------------- 12

2.5 Install the Temperature Probes: ------------------------------------------------------------ 13

2.6 Install the Pressure Transducers: ----------------------------------------------------------- 14

2.7 Install the Interface Circuit for Annuciators --------------------------------------------- 16

2.8 Install the Interface Circuit for Flaps and Trim ------------------------------------------ 17

2.9 Install the Interface Circuit for the Gear Position, Unsafe Indicator and Gear.. --- 17

2.10 Install the CO-Gaurdian CO Detector -------------------------------------------------- 18

2.11 Install the Shunt: ----------------------------------------------------------------------------- 18

2.12 Install the Fuel Flow Transducer: -------------------------------------------------------- 19

2.13 Install the P-300C Fuel Level Probes ---------------------------------------------------- 20

2.14 Install the P-300M Magnetic Fuel Level Sender --------------------------------------- 20

2.15 Install the Resistive Fuel Level Module (RFLM-4-X): ------------------------------- 21

2.16 Install the Voice Alarm Control Panel (AV-17CP): ----------------------------------- 21

2.17 Install the Intensity Control Pot (CP-1): ------------------------------------------------- 21

2.18 Install the Master Warning (red) and Caution (yellow) Lights ---------------------- 22

2.19 Install the EDC-33T: ------------------------------------------------------------------------ 22

3.0 Install the EDC Wire Harnesses and Route Wires --------------------------------------- 23

3.1 Attach the three EDC 37-pin Wire Harnesses to the EDC --------------------------- 25

3.2 Connect the EDC Harness to the Temperature Probes -------------------------------- 25

3.3 Connect the EDC Harness to the Pressure Transducers ------------------------------ 25

3.4 Connect the EDC Harness to the Shunt -------------------------------------------------- 26

3.5 Connect the EDC Harness to the Fuel Flow Transducer ------------------------------ 26

Contents

(Page 2 of 2)

3.6 Connect the RFLM-4-x Harness to the EDC Connector and to the Resistive Fuel Level Sensor ----------------------------------------------------------------------------- 27

3.7 Connect the EDC Harness to the Capacitive Fuel Level Probes ------------------- 27

3.8 Connect the EDC Harness to the P-300M Magnetic Fuel Level Senders --------- 28

3.9 Connect the EDC Harness (Volts Measurement Pin) to the Bus -------------------- 28

3.10 Connect the EDC Harness to the N1 and/or N2 Tach Generator ---------------- 28

3.11 Connect the EDC Harness to the VI-221's (Voltage Interface Units) ------------- 28

3.12 Connect the EDC Harness to Power and Ground ------------------------------------ 29

3.13 Route the EDC RS422 Wires to the MVP Connector -------------------------------- 29

4.0 Install the MVP Wire Harness and Route the Wires ------------------------------------ 31

4.1 Attach the MVP 25-pin D-Sub Connector to the MVP -------------------------------- 33

4.2 Connect the EDC RS422 Wires to the MVP RS422 Wires --------------------------- 33

4.3 Connect the MVP Harness to the Master Warning and Caution Lights ------------ 33

4.4 Connect the MVP Harness to the Voice Alarm Control Panel (AV-17CP) -------- 33

4.5 Connect the MVP Harness to the Audio Panel ------------------------------------------ 34

4.6 Connect the MVP Harness to the External Intensity Control Pot (CP-1) ---------- 34

4.7 Connect the MVP Harness to the Moving Map Data Out from the GPS ---------- 34

4.8 Connect the MVP Harness to the Fuel Data Input on the GPS --------------------- 34

4.9 Connect the MVP "Transmit Lockout Input" pin to the Transmit Key ------------ 35

4.10 Connect the MVP Harness to Power and Ground ------------------------------------ 35

4.11 Connect the MVP Harness to the CO-Guardian CO Detector -------------------- 35

5.0 Mandatory System Setup and Checkout ---------------------------------------------------- 37

5.1 Power-On Checkout: ------------------------------------------------------------------------ 39

5.2 Perform all Steps in the "MVP-50T Setup Checklist" -------------------------------- 39

5.3 Ground Run Checkout ----------------------------------------------------------------------- 39

5.4 First Flight Checkout ------------------------------------------------------------------------- 40

5.5 Read the "Warranty/Agreement" and the "Important Notice" ---------------------- 40

6.0 Installlation Data ----------------------------------------------------------------------------------- 41

6.1 Continued Airworthiness and Limitations -------------------------------------------------- 43

6.2 Airworthiness Limitations -------------------------------------------------------------------- 43

6.3 Working With Connectors -------------------------------------------------------------------- 43

6.31. Installing a Red Slip-on Connector onto a TC or Tin Copper Wire: ---------- 44

6.3.2 Installing a Yellow Precision TC Connector onto a TC Wire: ------------------ 45

6.3.3 Installing a D-sub Pin onto a TC or Tin Copper Wire: -------------------------- 45

MVP-50T 25-pin D-sub Connecot Wiring Diagram ------------------------------------- 47

EDC Wiring Work Sheet, Top Connector ------------------------------------------------- 48 EDC Wiring Work Sheet, Middle Connector --------------------------------------------- 49 EDC Wiring Work Sheet, Bottom Connector -------------------------------------------- 50

MVP Aircraft Panel Cutout -------------------------------------------------------- 51 EDC Template ---------------------------------------------------------------------- 52

7.0 Troubleshooting ------------------------------------------------------------------------------------- 5 3

7.1 MVP or EDC Problem: ------------------------------------------------------------------------ 55

7.2 Pressure Problem with one Function: ------------------------------------------------------- 56

7.3 Temperature Problem on all Channels: ----------------------------------------------------- 56

7.4 Temperature Problem with one Function: ------------------------------------------------- 57

7.5 N1 or N2 RPM Problem: ---------------------------------------------------------------------- 57

7.6 Fuel Flow Problem: ----------------------------------------------------------------------------- 58

7.7 Amp Problem: ----------------------------------------------------------------------------------- 59

7.8 Resistive Fuel Level Problem: ---------------------------------------------------------------- 59

7.9 Capacitive Fuel Level Problem: -------------------------------------------------------------- 60

7.10 Voltage Problem: ------------------------------------------------------------------------------ 61

7.11 Annunciator Problem: ------------------------------------------------------------------------ 61

8.0 Technical Data ------------------------------------------------------------------------------------- 6 3

Specifications ----------------------------------------------------------------------------------------- 8 pages DO-160 Environmental Qualification Form -------------------------------------------------- 3 pages

A Appendix ---------------------------------------------------------------------------------------------- A

A1.0 Appendix: Connecting an EDC Input to a Custom Probe -------------------------- A1.0 A2.0 Appendix: Connecting a Second EDC to the MVP ------------------------------- A2.0

Warranty / Agreement

Electronics International Inc. (EI) warrants this instrument and system components to be free from defects in materials and workmanship for a period of one year from the user invoice date. EI will repair or replace any item under the terms of this Warranty provided the item is returned to the factory prepaid.

ALLALL

If you do not agree to and accept If you do not agree to and accept

If you do not agree to and accept

If you do not agree to and accept If you do not agree to and accept

This ProductThis Product

This Product

This ProductThis Product

2. Electronics International Inc. is not liable or responsible for a pilot’s action or any situation that results in personal injury, property damage, missed commitments, lack of use of an aircraft or any expenses incurred due to: product failure, inaccuracy in displayed data or text files, display or display format issues, software bugs or problems, upgrade or customization issues, misinterpretation of the display, warning and/or limit settings, calibration problems, installation issues (leaks, mis-wiring, obstructions, damage to aircraft or components, incorrect installation of any parts, wrong parts, part that don’t fit, etc.) or any other issues related to the installation or operation of this product. All of the above are solely the pilot’s and/or installer’s responsibility. The

must must

pilot

must understand the operation of this product before flying the aircraft. The pilot will not allow anyone

must must to operate the aircraft that does not know the operation of this product. The pilot will keep the instrument's Operating Instructions in the aircraft at all times.

By installing this product, the aircraft owner/pilot and installer agree to hold Electronics International Inc. harmless and in no way responsible for monetary compensation, including punitive damages for any incident, harm and/or damage associated with this product (including but not limited to the ones listed above). If you do not agree to any part of this Warranty/Agreement,

. .

. You may return the product for a refund, contact Electronics International Inc. for details.

. .

the terms of this Warranty/Agreement, the terms of this Warranty/Agreement,

ALL

the terms of this Warranty/Agreement,

ALLALL

the terms of this Warranty/Agreement, the terms of this Warranty/Agreement,

DO NOT INSTALL THIS PRODUCT.DO NOT INSTALL THIS PRODUCT.

DO NOT INSTALL THIS PRODUCT.

DO NOT INSTALL THIS PRODUCT.DO NOT INSTALL THIS PRODUCT.

DO NOT InstallDO NOT Install

DO NOT Install

DO NOT InstallDO NOT Install

3. This Warranty/Agreement shall not apply to any product that has been repaired or altered by any person other than Electronics International Inc., or that has been subjected to misuse, accident, incorrect wiring, negligence, improper or unprofessional assembly or improper installation by any person. does not cover any reimbursement for any person’s time for installation, removal, assembly ordoes not cover any reimbursement for any person’s time for installation, removal, assembly or

does not cover any reimbursement for any person’s time for installation, removal, assembly or

does not cover any reimbursement for any person’s time for installation, removal, assembly ordoes not cover any reimbursement for any person’s time for installation, removal, assembly or repair.repair.

repair. Electronics International retains the right to solely determine the reason or cause for warranty repair.

repair.repair.

4. This warranty does not extend to any machine, vehicle, boat, aircraft or any other device to which the Electronics International Inc. product may be connected, attached, interconnected or used in conjunction with in any way.

5. Personal injury or property damage due to misinterpretation or lack of understanding of this product is solely the pilots' responsibility. The pilot flying the aircraft. If he/she does not, he or she agrees to seek training from a knowledgeable instructor. The pilot also agree that no one will be allowed to operate the aircraft that does not know the operation of this product and will

6. The obligation assumed by Electronics International Inc. under this warranty is limited to repair, replacement or refund of the product, at the sole discretion of Electronics International Inc.

7. Electronics International Inc. is not liable for expenses incurred by the customer or installer due to factory updates, modifications, improvements, changes, or any other alterations to the product that may affect the form, fit, function or operation of the product.

Keep the Operating Instructions in the aircraft at all times.Keep the Operating Instructions in the aircraft at all times.

Keep the Operating Instructions in the aircraft at all times.

Keep the Operating Instructions in the aircraft at all times.Keep the Operating Instructions in the aircraft at all times.

must must

must understand all aspects of the operation of this product before

must must

This warrantyThis warranty

This warranty

This warrantyThis warranty

More On Next PageMore On Next Page

8. Electronics International is not responsible for shipping charges or damages incurred under this Warranty.

9. No representative is authorized to assume any other liability for Electronics International Inc. in connection with the sale of Electronics International Inc. products.

You must read the entire Installation and Operating Instructions for this instrument. If youYou must read the entire Installation and Operating Instructions for this instrument. If you

You must read the entire Installation and Operating Instructions for this instrument. If you

10.

You must read the entire Installation and Operating Instructions for this instrument. If youYou must read the entire Installation and Operating Instructions for this instrument. If you

do not agree to and accept the terms of this Warranty/Agreement and the responsibilities setdo not agree to and accept the terms of this Warranty/Agreement and the responsibilities set

do not agree to and accept the terms of this Warranty/Agreement and the responsibilities set

do not agree to and accept the terms of this Warranty/Agreement and the responsibilities setdo not agree to and accept the terms of this Warranty/Agreement and the responsibilities set forth in these manuals, DO NOT install this product, contact E.I. for a refund.forth in these manuals, DO NOT install this product, contact E.I. for a refund.

forth in these manuals, DO NOT install this product, contact E.I. for a refund.

forth in these manuals, DO NOT install this product, contact E.I. for a refund.forth in these manuals, DO NOT install this product, contact E.I. for a refund.

This Warranty is made only to the original user. WARRANTIES OR OBLIGATIONS: EXPRESS OR IMPLIED. MANUFACTURER EXPRESSLYWARRANTIES OR OBLIGATIONS: EXPRESS OR IMPLIED. MANUFACTURER EXPRESSLY

WARRANTIES OR OBLIGATIONS: EXPRESS OR IMPLIED. MANUFACTURER EXPRESSLY

WARRANTIES OR OBLIGATIONS: EXPRESS OR IMPLIED. MANUFACTURER EXPRESSLYWARRANTIES OR OBLIGATIONS: EXPRESS OR IMPLIED. MANUFACTURER EXPRESSLY DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ADISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A

DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A

DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ADISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PURCHASER AGREES THAT IN NO EVENT SHALL MANUFAC-PARTICULAR PURPOSE. PURCHASER AGREES THAT IN NO EVENT SHALL MANUFAC-

PARTICULAR PURPOSE. PURCHASER AGREES THAT IN NO EVENT SHALL MANUFAC-

PARTICULAR PURPOSE. PURCHASER AGREES THAT IN NO EVENT SHALL MANUFAC-PARTICULAR PURPOSE. PURCHASER AGREES THAT IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, IN-TURER BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, IN-

TURER BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, IN-

TURER BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, IN-TURER BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING LOST PROFITS OR LOSS OF USE OR OTHER ECONOMIC LOSS. EXCEPT ASCLUDING LOST PROFITS OR LOSS OF USE OR OTHER ECONOMIC LOSS. EXCEPT AS

CLUDING LOST PROFITS OR LOSS OF USE OR OTHER ECONOMIC LOSS. EXCEPT AS

CLUDING LOST PROFITS OR LOSS OF USE OR OTHER ECONOMIC LOSS. EXCEPT ASCLUDING LOST PROFITS OR LOSS OF USE OR OTHER ECONOMIC LOSS. EXCEPT AS EXPRESSLY PROVIDED HEREIN, MANUFACTURER DISCLAIMS ALL OTHER LIABILITYEXPRESSLY PROVIDED HEREIN, MANUFACTURER DISCLAIMS ALL OTHER LIABILITY

EXPRESSLY PROVIDED HEREIN, MANUFACTURER DISCLAIMS ALL OTHER LIABILITY

EXPRESSLY PROVIDED HEREIN, MANUFACTURER DISCLAIMS ALL OTHER LIABILITYEXPRESSLY PROVIDED HEREIN, MANUFACTURER DISCLAIMS ALL OTHER LIABILITY TO PURCHASER OR ANY OTHER PERSON IN CONNECTION WITH THE USE OR PERFOR-TO PURCHASER OR ANY OTHER PERSON IN CONNECTION WITH THE USE OR PERFOR-

TO PURCHASER OR ANY OTHER PERSON IN CONNECTION WITH THE USE OR PERFOR-

TO PURCHASER OR ANY OTHER PERSON IN CONNECTION WITH THE USE OR PERFOR-TO PURCHASER OR ANY OTHER PERSON IN CONNECTION WITH THE USE OR PERFORMANCE OF MANUFACTURER’S PRODUCTS, INCLUDING SPECIFICALLY LIABILITY INMANCE OF MANUFACTURER’S PRODUCTS, INCLUDING SPECIFICALLY LIABILITY IN

MANCE OF MANUFACTURER’S PRODUCTS, INCLUDING SPECIFICALLY LIABILITY IN

MANCE OF MANUFACTURER’S PRODUCTS, INCLUDING SPECIFICALLY LIABILITY INMANCE OF MANUFACTURER’S PRODUCTS, INCLUDING SPECIFICALLY LIABILITY IN TORT.TORT.

TORT.

TORT.TORT.

THIS WARRANTY IS IN LIEU OF ALL OTHERTHIS WARRANTY IS IN LIEU OF ALL OTHER

THIS WARRANTY IS IN LIEU OF ALL OTHER

THIS WARRANTY IS IN LIEU OF ALL OTHERTHIS WARRANTY IS IN LIEU OF ALL OTHER

System OverviewSystem Overview

System Overview

System OverviewSystem Overview

1.1 System Description

1.1.1 MVP Display:1.1.1 MVP Display:

1.1.1 MVP Display:

1.1.1 MVP Display:1.1.1 MVP Display:

1.1.2 EDC-33T:1.1.2 EDC-33T:

1.1.2 EDC-33T:

1.1.2 EDC-33T:1.1.2 EDC-33T:

1.1.3 Probes, Transducers and Modules:1.1.3 Probes, Transducers and Modules:

1.1.3 Probes, Transducers and Modules:

1.1.3 Probes, Transducers and Modules:1.1.3 Probes, Transducers and Modules:

1.1.4 Wiring & Extension Cables:1.1.4 Wiring & Extension Cables:

1.1.4 Wiring & Extension Cables:

1.1.4 Wiring & Extension Cables:1.1.4 Wiring & Extension Cables:

1.2 Operational Overview:

1.3 Installation Overview:

1.01.0

1.0

1.01.0

1.4 Password Protection:

1.4.1 Level #1 Password (Maintenance):1.4.1 Level #1 Password (Maintenance):

1.4.1 Level #1 Password (Maintenance):

1.4.1 Level #1 Password (Maintenance):1.4.1 Level #1 Password (Maintenance):

1.4.2 Level #2 Password (OEM/Experimental):1.4.2 Level #2 Password (OEM/Experimental):

1.4.2 Level #2 Password (OEM/Experimental):

1.4.2 Level #2 Password (OEM/Experimental):1.4.2 Level #2 Password (OEM/Experimental):

1.1 1.1

System Description:System Description:

1.1

System Description:

1.1 1.1

System Description:System Description:

The MVP-50 Glass Panel Engine Monitor Installation consists of four major components: the MVP Display, the Engine Data Converter (EDC-33T), the Probes, Transducers & Modules, and the Wiring and Extension Cables.

1.1. 1.1.

MVP Display:MVP Display:

1.1.

MVP Display:

1.1. 1.1.

MVP Display:MVP Display:

Pwr & Gnd

Master

Warning

LightsLights

Lights

LightsLights

Light

GPS

Audio Panel

The MVP Display unit measures 5.55" wide by 5.15" high by 2.4" deep and is designed to be mounted from behind the aircraft instrument panel. The MVP could be mounted on to a sub-panel which would then be mounted to the aircraft instrument panel from the front.

The 25-pin D-sub connector on the back of the MVP Display is used to interface the MVP to the EDC33P, Power & Ground, GPS, Master Warning and Caution Lights, Audio Panel, etc.

1.1.2 1.1.2

1.1.2

1.1.2 1.1.2

EDC-33T:EDC-33T:

EDC-33T:

EDC-33T:EDC-33T:

The EDC-33T (Engine Data Converter) converts all of the engine and aircraft system signals into serial data. This data is transmitted to the MVP display via two wires (RS422). If a second EDC is installed, one of the data lines wil be connected to a RS232 channel on the MVP. The EDC measures 4.5" long by 3.5" wide by 2.2" high and is to be mounted on the cockpit side of the firewall or in an equipment bay. The EDC reduces the wire bundle to the instrument panel by over 100 wires. There are three 37pin D-sub connectors that interface the EDC to the various probes, transducers and modules.

The EDC’s Temperature and Fuel Level inputs can be used to monitor voltage outputs from almost any transducer. In this way almost any function can be displayed on the MVP.

Up to two EDC’s can be connected to the MVP at a one time. This significantly increases the total number of functions that can be displayed on the MVP.

1.1.3 1.1.3

1.1.3

1.1.3 1.1.3

Probes, Transducers and Modules:Probes, Transducers and Modules:

Probes, Transducers and Modules:

Probes, Transducers and Modules:Probes, Transducers and Modules:

The various probes, transducers and modules are mounted in the aircraft at appropriate locations.

1.1.4 1.1.4

1.1.4

1.1.4 1.1.4

The extension cables and wiring provide the connections from the probes, modules or direct connections to the EDC inputs. Once the Wiring and Extension Cables are installed into the aircraft they become semi-permanent. Everything else (MVP, EDC, Probes and Modules) can be easily disconnected and removed.

Wiring & Extension Cables:Wiring & Extension Cables:

Wiring & Extension Cables:

Wiring & Extension Cables:Wiring & Extension Cables:

1.2 Operational Overview:

The MVP system measures an engine or aircraft function using a probe or transducer and displays that function on the MVP screen using the following steps:

A. A probe is mechanically connected to the aircraft and electrically connected to an EDC input. The

pre-wired harness provides most of the electrical connections from the probes to the EDC inputs.

B. The EDC converts the signals from the probes to a digital format (RS422) and sends the data to the

MVP. The EDC has 33 inputs. Many of the inputs can be used for a number of different types of functions.

C. The MVP receives the data from the EDC and the data is processed through the MVP as follows:

1. The data received for each EDC input is assigned a function name and probe. Function names and probes are set up for each EDC input in System Configuration Screen #1. The probe assigned provides specific calibration algorithms. Calibration algorithms for any function can be modified in System Configuration Screen #5. Some functions have special calibration/setup screens (Fuel Tank Calibration, Tach Time, Engine Hours, Flight Time, Pressure Altitude, Flaps, Trim, etc.).

2. The function is then placed on the Main or System screen of the MVP. System Configuration Screens #2 or #3 allows the placement location of the function to be selected for either the Main or System screen.

3. The analog and/or digital display of the function (with redlines, limits, colors, etc) is depicted on the appropriate screen. Redlines, limits, colors, units, blinking, master warnings and voice files can be set up for any function in Configuration Screens #4.

Much of the setup for the certified MVP is done at the factory and cannot be changed by the pilot or installer. See the following Password Protection section for more information.

1.3 Installation Overview:

The installer should start the installation by reviewing the EDC Wiring Work Sheets. There are three work sheets, one for each of the 37-pin D-Sub connectors on the EDC. The work sheets are packaged with each of the three EDC wire harnesses. The work sheets provide a list of the functions and probes/transducers included with this kit. The installation is achieved by performing the following steps:

A. The MVP display is installed. The MVP can be mounted one of two ways; from behind the instru-

ment panel or on a sub-panel, which is then mounted to the aircraft instrument panel from the front. This method hides the cutout for the MVP case and makes a clean and good-looking installation. Electronics International has a MVP sub-panel avaliable (see E.I. Price List for more information).

B. Probes and Transducers are installed.

Control Panels, Pots and Warning Lights are installed.

The EDC is installed. This should be installed on the inside of the cockpit or in an instrument bay.

For a twin-engine aircraft it can be installed on the backside (not the engine side) of the firewall.

The Wire Harnesses are installed. The wire harnesses for the EDC and MVP are pre-wired and in-

cluded in the kit.

Field Calibration/Setup steps are performed. Weight & Balance, Fuel Tanks, Horsepower, etc. func-

tions are calibrated/setup. Calibration/Setup requires a password. See the following Password Protection section for more information.

G. System Checkout is performed.

1.4 Password Protection:

The MVP provides a number of screens for the pilot to use during flight, none of which require a password. It also provides many System Configuration Screens that are used to configure the MVP for a specific aircraft. Some of the aircraft functions (fuel level, flaps, trim, weight and balance, etc.) must be calibrated during installation and some must be set at the factory or by an OEM.

The MVP provides two levels of passwords for configuring and calibrating the unit.

1.4.1 1.4.1

1.4.1

1.4.1 1.4.1

The Level #1 password is for the installer or maintenance personnel. This password allows the installer to perform the following:

For a non-certified MVP, the password is “100.” For a certified unit the password must be obtained from Electronics International Inc. To qualify for the maintenance password you must be a certified mechanic or FAA approved shop.

Level #1 Password (Maintenance):Level #1 Password (Maintenance):

Level #1 Password (Maintenance):

Level #1 Password (Maintenance):Level #1 Password (Maintenance):

A. Delete Log Files. B. Set up the Gear Warning. C. Adjust the Recovery Factor. D. Calibrate the Fuel Level for all fuel tanks. E. Adjust the aircraft’s Weight and Balance data. F. Set the Fuel Weight, Tach Time and Engine Hours. G. Set up the Serial Ports. H. Disable the Bar Graph. I. Calibrate Pressure Altitude. J. Calibrate Flap and Trim indications.

The password protects the MVP from unauthorized access to calibration data. If calibration data is improperly changed, it could lead to engine or aircraft damage and/or personal injury. Once the MVP is installed and checked out, the password should be changed (on either the certified or non-certified unit) to a unique number and it should be protected from unauthorized access.

If the new password is lost or a new shop requires access to calibration data (as allowed by the Maintenance Password), Electronics International has a method of providing the Maintenance Password to any authorized shop or personnel.

1.4.2 1.4.2

1.4.2

1.4.2 1.4.2

The Level #2 password is for the Factory, OEM’s, Certified Installers, or experimental users. This password allows access to all System Configuration Data. For a non-certified MVP, the password is “100.” For a certified unit the password is only released under a contract or agreement.

The password protects the MVP from unauthorized access to calibration data. If calibration data is improperly changed, it could lead to engine or aircraft damage and/or personal injury. Once the unit is installed and checked out, this password should be changed (on either the certified or non-certified unit) to a unique number and should be protected from unauthorized access.

Level #2 Password (OEM/Experimental):Level #2 Password (OEM/Experimental):

Level #2 Password (OEM/Experimental):

Level #2 Password (OEM/Experimental):Level #2 Password (OEM/Experimental):

Hardware InstallationHardware Installation

Hardware Installation

Hardware InstallationHardware Installation

2.1 Important Information and Initial Checkout:

2.2 Review the "EDC Wiring Work Sheets:"

2.3 Verify You Have all the Probes, Modules, Transducers and Cables:

2.4 Install the MVP Display:

2.5 Install the Temperature Probes:

2.6 Install the Pressure Transducers:

2.7 Install the Interface Circuit for Annunciators:

2.8 Install the Interface Circuit for Flap and Trim Pots:

2.02.0

2.0

2.02.0

2.9 Install the Interface Circuit for the Gear Position, Unsafe Indicator and Gear W arning:

2.10 Install the CO Guardian CO Detector:

2.11 Install the Shunt:

2.12 Install the Fuel Flow Transducer:

2.13 Install the P-300C Fuel Level Probes:

2.14 Install the P-300M Magnetic Fuel Level Sender:

2.15 Install the Resistive Fuel Level Module (RFLM-4-X):

2.16 Install the Voice Alarm Control Panel:

2.17 Install the Intensity Control Pot (Optional):

2.18 Install the Master Warning (red) and Caution (yellow) Lights:

2.19 Installing the EDC-33T:

2.1 Important Information and Initial Check Out:

The installer and aircraft owner must read the Warranty/Agreement before starting theThe installer and aircraft owner must read the Warranty/Agreement before starting the

The installer and aircraft owner must read the Warranty/Agreement before starting the

The installer and aircraft owner must read the Warranty/Agreement before starting theThe installer and aircraft owner must read the Warranty/Agreement before starting the

installation.installation.

installation. There is information in the Warranty/Agreement that may alter your decision to install

installation.installation. this instrument. this instrument.this instrument.

this instrument.

this instrument.this instrument.

If you are not an FAA Certified Aircraft Mechanic familiar with the issues of installing If you are not an FAA Certified Aircraft Mechanic familiar with the issues of installing

If you are not an FAA Certified Aircraft Mechanic familiar with the issues of installing

If you are not an FAA Certified Aircraft Mechanic familiar with the issues of installing If you are not an FAA Certified Aircraft Mechanic familiar with the issues of installing

engine and aircraft instruments, engine and aircraft instruments,

engine and aircraft instruments,

engine and aircraft instruments, engine and aircraft instruments, should use current aircraft standards and practices to install this instrument (refer to ACshould use current aircraft standards and practices to install this instrument (refer to AC

should use current aircraft standards and practices to install this instrument (refer to AC

should use current aircraft standards and practices to install this instrument (refer to ACshould use current aircraft standards and practices to install this instrument (refer to AC

43.13).43.13).

43.13).

43.13).43.13).

Check that any necessary FAA Approvals are available for your aircraft before startingCheck that any necessary FAA Approvals are available for your aircraft before starting

Check that any necessary FAA Approvals are available for your aircraft before starting

Check that any necessary FAA Approvals are available for your aircraft before startingCheck that any necessary FAA Approvals are available for your aircraft before starting

the installation.the installation.

the installation.

the installation.the installation.

If you do not accept the terms of the Warranty/Agreement, do not installIf you do not accept the terms of the Warranty/Agreement, do not install

If you do not accept the terms of the Warranty/Agreement, do not install

If you do not accept the terms of the Warranty/Agreement, do not installIf you do not accept the terms of the Warranty/Agreement, do not install

Do not attempt to install this instrument.Do not attempt to install this instrument.

Do not attempt to install this instrument.

Do not attempt to install this instrument.Do not attempt to install this instrument.

The installer The installer

The installer

The installer The installer

D. Read the Installation Instructions entirely and resolve any issues you may have

installation. This may eliminate any delays once the installation is started.

E. Inspect the contents of this package prior to installation.

stalled into a certified aircraft, check that the Model Number listed on the TSO labelstalled into a certified aircraft, check that the Model Number listed on the TSO label

stalled into a certified aircraft, check that the Model Number listed on the TSO label

stalled into a certified aircraft, check that the Model Number listed on the TSO labelstalled into a certified aircraft, check that the Model Number listed on the TSO label incorporates the Aircraft ID for which it is to be installed. Each MVP-50T display isincorporates the Aircraft ID for which it is to be installed. Each MVP-50T display is

incorporates the Aircraft ID for which it is to be installed. Each MVP-50T display is

incorporates the Aircraft ID for which it is to be installed. Each MVP-50T display isincorporates the Aircraft ID for which it is to be installed. Each MVP-50T display is configured for a specific aircraft and should only be installed in that aircraft.configured for a specific aircraft and should only be installed in that aircraft.

configured for a specific aircraft and should only be installed in that aircraft.

configured for a specific aircraft and should only be installed in that aircraft.configured for a specific aircraft and should only be installed in that aircraft.

Do not install a non-certified MVP in a certified aircraft.Do not install a non-certified MVP in a certified aircraft.

Do not install a non-certified MVP in a certified aircraft. A certified MVP lists the applicable

Do not install a non-certified MVP in a certified aircraft.Do not install a non-certified MVP in a certified aircraft. TSO numbers at the bottom of the Model Label.

Before starting the installation make sure the instrument will fit in the location youBefore starting the installation make sure the instrument will fit in the location you

Before starting the installation make sure the instrument will fit in the location you

Before starting the installation make sure the instrument will fit in the location youBefore starting the installation make sure the instrument will fit in the location you

intend to install it without obstructing the operation of any controls.intend to install it without obstructing the operation of any controls.

intend to install it without obstructing the operation of any controls. CFR 23.1321(a)

intend to install it without obstructing the operation of any controls.intend to install it without obstructing the operation of any controls. states, “Each flight, navigation, and powerplant instrument for use by any required pilot during takeoff, initial climb, final approach, and landing must be located so that any pilot seated at the controls can monitor the airplane’s flight path and these instruments with minimum head and eye movement.” AC 23.1311-1B provides one method (but not the only method) of complying with this CFR. AC 23.1311-1B recommends a powerplant instrument be installed within a distance of 21" from the pilot’s visual centerline to the middle of the instrument. The pilot’s visual centerline is a perpendicular line from the pilot’s eye to the instrument panel. In most aircraft, installing the MVP50T to the right of the Radio Stack would be acceptable. In some aircraft, the visual centerline falls to the right of the Attitude Indicator.

If the MVP-50T system is to be in- If the MVP-50T system is to be in-

If the MVP-50T system is to be in-

If the MVP-50T system is to be in- If the MVP-50T system is to be in-

beforebefore

before starting the

beforebefore

If the powerplant instrument cannot be installed within 8" of the pilot’s visual centerline, AC 23.13111B recommends Master Caution and Warning Lights be installed. Installation of Master Caution and Warning Lights is covered in this manual.

H. If this instrument is to replace an existing gauge in the aircraft, it is the installer’s responsibility to

move or replace any existing instruments or components in accordance with FAA approved methods and procedures (see AC 43.13).

J. An Installation Checklist is provided to assist the installation of the MVP system. It does not replace

the instructions located in this manual.

2.2 Review the "EDC Wiring Work Sheets:"

There are a number of probes and extension cables that will need to be installed. The key to keeping the installation simple is to organize the work using the Review the functions assigned to each EDC input on the EDC Wiring Work Sheets. The work sheets are prepared at the factory with the functions and probes already assigned.

"EDC Wiring Work Sheets" "EDC Wiring Work Sheets"

"EDC Wiring Work Sheets" supplied with this kit.

"EDC Wiring Work Sheets" "EDC Wiring Work Sheets"

2.3 Verify Your Have all the Probes, Modules, Transducers and Cables:

The three EDC 37-pin D-sub connectors and the MVP 25-pin D-sub connector are pre-wired at the factory. The three EDC connectors are marked Top, Middle and Bottom. The EDC Wiring Work Sheets provide a list of the probes supplied with this kit.

A. Check that you have all the probes listed on the EDC Wiring Work Sheets.

B. Check that the three EDC 37 pin-D-sub wire harnesses are provided with the proper wires for

each of the probes shown on the EDC Wiring Work Sheets.

C. Check that the MVP 25-pin D-sub wire harness is provided.

2.4 Installing the MVP Display:

Before starting the installation make sure the instrument will fit in the location you intend toBefore starting the installation make sure the instrument will fit in the location you intend to

Before starting the installation make sure the instrument will fit in the location you intend to

Before starting the installation make sure the instrument will fit in the location you intend toBefore starting the installation make sure the instrument will fit in the location you intend to install it without obstructing the operation of any controls. install it without obstructing the operation of any controls.

install it without obstructing the operation of any controls. The MVP display can be installed in

install it without obstructing the operation of any controls. install it without obstructing the operation of any controls. one of two ways, depending on convenience or the installer's preference. The first method is the traditional method of installing the MVP display from behind the panel. An aircraft panel cutout drawing is provided at the back of this manual.

The second method is more suitable when an MVP display is to be mounted in an existing aircraft panel. This method requires creating a sub-panel slightly larger than the MVP display. The MVP display is mounted in the sub-panel and the sub-panel is mounted on the front of the existing aircraft panel. This allows the installer to rough-cut a hole in the aircraft panel to accommodate the MVP display. The sub-panel covers any imperfections in the cut hole. Also, the MVP display may easily be removed from the front of the aircraft panel.

The sub-panel should be made from .062" (or thicker) aluminum and can be painted black or the same color as the aircraft panel. Four screws (6-32 or larger) located at the top and bottom of the sub-panel should be used to mount the sub-panel to the aircraft panel. If there is no room at the top and bottom for mounting screws, they may be placed on the sides of the sub-panel.

MVP

Sub-panel

CFR 23.1321(a) states, “Each flight, navigation, and powerplant instrument for use by any required pilot during takeoff, initial climb, final approach, and landing must be located so that any pilot seated at the controls can monitor the airplane’s flight path and these instruments with minimum head and eye movement.” AC 23.1311-1B provides one method (but not the only method) of complying with this CFR. AC

23.1311-1B recommends a powerplant instrument be installed within a distance of 21" from the pilot’s

visual centerline to the middle of the instrument. The pilot’s visual centerline is a perpendicular line from

the pilot’s eye to the instrument panel. In most aircraft, installing the MVP-50P to the right of the radio stack would be acceptable. In some aircraft, the visual centerline falls to the right of the Attitude Indicator.

If the powerplant instrument cannot be installed within 8" of the pilot’s visual centerline, AC 23.1311-1B recommends Master Caution and Warning Lights be installed. Installation of Master Caution and Warning Lights is covered in this manual.

Installing the MVP-50P may require an instrument (or two) to be moved to a new location. The MVP-50P replaces eight or more primary instruments in the aircraft instrument panel, therefore moving an instrument to a new location may not be an issue. If the installer is unwilling or unable to find a location for the MVP-50P, Not InstallNot Install

Not Install the MVP-50P. The system may be returned for a refund (contact EI for more information).

Not InstallNot Install

DoDo

2.5 Install the Temperature Probes:

Install only the Temperature Probes applicable for your configuration.

A. A.

OIL Temperature Probe Installation:OIL Temperature Probe Installation:

OIL Temperature Probe Installation:

A. A.

OIL Temperature Probe Installation:OIL Temperature Probe Installation:

The MVP system can interface with existing resistive or thermocouple type oil temperature probes or one of E.I.’s Type-K sealed probes may be installed. See the E.I. pricelist for a list of available probes. Check

that the probe depth does not interfere with the inner workings of the engine.

To EDC

Temp Input

(Middle or Bottom

Connector)

B. B.

OAT Probe Installation:OAT Probe Installation:

OAT Probe Installation:

B. B.

OAT Probe Installation:OAT Probe Installation:

Mount the OAT Probe in an appropriate location on the aircraft, using the hardware supplied. The OAT Probe is sensitive to air temperature changes. For this reason, the cowl or engine exiting air (i.e., on the belly of the aircraft). Also, if the probe is mounted in the cowling area, radiant heat may influence the probe temperature. Other than these considerations, the OAT Probe may be mounted in an air intake vent, on the side of the cowling or anywhere else on the aircraft.

To EDC

Temp Input

(Middle Connector, Ch 8

Recommended)

(Red)

P-120 Oil Temp Probe, 5/8" -18, Type K. Used on most engines.

(Yel)

do not mount the OAT probe in the path of

P-128 Carb Temp / OAT Probe, 1/4" -28, Type K. Used on most engines.

C. C.

Other Temperature Probe Installation:Other Temperature Probe Installation:

Other Temperature Probe Installation:

C. C.

Other Temperature Probe Installation:Other Temperature Probe Installation:

Other temperature probes (Cabin Temp, Cowl Temp for fire detection, etc.) may be installed using current aircraft standards and practices (refer to AC 43.13). Make sure these probes do not interfere with the operation of the engine or aircraft.

2.6 Install the Pressure Transducers:

Install only the Pressure Transducers applicable for your configuration.

A. A.

Torque Pressure Transducer Installation:Torque Pressure Transducer Installation:

Torque Pressure Transducer Installation:

A. A.

Torque Pressure Transducer Installation:Torque Pressure Transducer Installation:

Some engines have a High and Low Torque pressure ports. These engines will require two pressure transducer to be installed. The MVP system can interface with many different types of pressure transducers.

Find a convenient location on the firewall or a mounting bracket and mount the pressure transducer(s) with the clamp provided.

transducer(s) to an engine baffle or directly onto the engine with the transducer supported by the threads. Vibration can cause the

threads to break, resulting in loss of engine fluid. The pressure transducer is equipped with a 1/8" NPT male port. This port can be adapted to any pressure line. Use only a flexible hose and fittings suitable for aircraft use. Route a flexible fuel pressure line from the primary torque pressure pick up point to the pressure transducer and tighten all fittings. Do not use the case of the pressure transducer

to tighten the pressure fittings.

Do not mount the pressure

To EDC

Press Input

(Top Connector)

(Red) (Blk) (Grn) (Wht)

Pressure Transducer: PT-100GA for 0 to 120 psi and PT-300GA for 0 to 300 psi.

Some fittings you may want to consider using are listed above.

1/8 NPT Male

PT-100GA

1/8 NPT Coupler

1/8 NPT Male

Pressure Transducer

AN910-1D

B. B.

Oil Pressure Transducer Installation:Oil Pressure Transducer Installation:

Oil Pressure Transducer Installation:

B. B.

Oil Pressure Transducer Installation:Oil Pressure Transducer Installation:

Find a convenient location on the firewall or a mounting bracket and mount the pressure transducer with the clamp provided. Do not mount the

pressure transducer directly on the engine with the transducer supported by threads. Vibration can cause the threads to break, resulting in loss of engine oil. The

pressure transducer is equipped with an 1/8" NPT male port. This port can be adapted to any oil pressure line. Use only a flexible hose and fittings suitable for aircraft use. Route a flexible oil pressure line from the primary oil pressure pick up point to the pressure transducer and tighten all fittings. Do not use the case of the pressure

transducer to tighten the pressure fittings.

Flare

To EDC

Press Input

(Top Connector)

(Red) (Blk) (Grn) (Wht)

#2 Straight - AN816-2D

#3 Straight - AN816-3D #4 Straight - AN816-4D

#2 45' - MS20823-2D #3 45' - MS20823-3D #4 45' - MS20823-4D

#2 90' - MS20822-2D #3 90' - MS20822-3D #4 90' - MS20822-4D

Some fittings you may want to consider using are listed below:

Pressure Transducer: PT-100GA for 0 to 120 psi and PT-300GA for 0 to 300 psi.

C. C.

Fuel Pressure Transducer Installation:Fuel Pressure Transducer Installation:

Fuel Pressure Transducer Installation:

C. C.

Fuel Pressure Transducer Installation:Fuel Pressure Transducer Installation:

Find a convenient location on the firewall and mount the pressure transducer with the clamp provided.

To EDC

Press Input

(Top Connector)

(Red) (Blk) (Grn) (Wht)

Do not mount the pressure transducer to an engine baffle or directly on the engine with the transducer supported by an adapter or fitting. Vibration can cause the adapter to break, resulting in loss of

engine oil. The pressure transducer is equipped with an 1/8" NPT male port. This port can be adapted to any oil pressure line. Use only a flexible hose and fittings suitable for aircraft use. Route a flexible oil pressure line from the

primary oil pressure pickup

point to the pressure transducer and tighten all fittings. Do not use the case of the

pressure transducer to tighten the pressure fittings.

Some fittings you may want to consider using are listed above.

D. D.

Gyro Vacuum Pressure Transducer Installation:Gyro Vacuum Pressure Transducer Installation:

Gyro Vacuum Pressure Transducer Installation:

D. D.

Gyro Vacuum Pressure Transducer Installation:Gyro Vacuum Pressure Transducer Installation:

Mount the PT-05Diff Pressure Transducer on the inside firewall or in the equipment bay under the aircraft instrument panel. Use the holes in the bottom plate to mount the PT-05Diff. Only two mounting holes are required.

PRESS

Connect the aircraft gyro vacuum line to the port tagged "Vac" on the PT-05Diff. Leave the port tagged "Press" open for non-

Open or Overboard

Pressure Line

VAC

pressurized aircraft. On pressurized aircraft connect the port tagged "Press" to the gyro overboard pressure line. Be sure these lines are tight. The ports are 1/4" flare union. Care should be taken not to put excess

To EDC

Press Input

(Top Connector)

(Red) (Blk) (Grn) (Wht)

Gyro Vacuum Line

The PT-05Diff, Pressure Transducer (0 to 6" Hg)

pressure on the flexible lines. Make sure the flexible lines do not kink.

Airspeed Transducer Installation:Airspeed Transducer Installation:

E. E.

Airspeed Transducer Installation:

Airspeed Transducer Installation:Airspeed Transducer Installation:

E. E.

Connect the aircraft pitot (airspeed) line to the port tagged "Press" on the PT-05Diff. Connect the aircraft static pressure line to the port tagged "Vac" on the PT-05Diff. Be sure these lines are tight. The ports are 1/4" flare union. Care should be taken not to put excess pressure on the flexible lines. Make sure the flexible lines do not kink. The Appendix at the back of the "Operating Instructions" manual provides calibration instructions for Airspeed.

F. F.

Altitude Tansducer Installation:Altitude Tansducer Installation:

Altitude Tansducer Installation:

F. F.

Altitude Tansducer Installation:Altitude Tansducer Installation:

Mount the PT-30Alt Altitude Transducer on the inside firewall or in the equipment bay under the aircraft instrument panel. Use the holes in the bottom plate to mount the PT-30Alt. Only two mounting holes are required.

Connect the aircraft static line (airspeed) line

.170" ID Flexible Tube

to the port on the PT-30Alt. Be sure this line is tight. The port is a 1/4" flare union. Care should be taken not to put excess

Aircraft Static Line

pressure on the flexible line. Make sure the flexible line does not kink.

G. G.

Other Pressure Transducer Installations:Other Pressure Transducer Installations:

Other Pressure Transducer Installations:

G. G.

Other Pressure Transducer Installations:Other Pressure Transducer Installations:

To EDC

Press Input

(Top Connector)

Other pressure transducers should be mounted in the aircraft in the same manner as the Gyro Vacuum Transducer or the Oil and Fuel Pressure Transducers, as appropriate. Note: Any unused + or -

pressure inputs must be grounded to a ground pin on the EDC 37-pin connector.

2.7 Install the Interface Circuit for Annunciators:

Any Temperature or Resistive Fuel Level channel on the EDC may be used to monitor the state of a switch, relay or output from a device. This output can be used to trigger a light (annunciator) on the MVP. Annunciator lights such as Chip Detect, Bypass, Deice, Pitot Heat, Fire, Fault, Exceedance, etc. can be displayed on the Main or System screen on the MVP.

To monitor a voltage, a VI-221 (Voltage Interface Unit) will be required. This consists of a 221K ohm resistor heat shrunk between two wires with a D-Sub pin crimped on one end. The following methods may be used to interface an EDC channel (using a VI-221) to a switch, relay or device:

A. A.

Monitoring a Signal That Switches Between Any Voltage and Ground:Monitoring a Signal That Switches Between Any Voltage and Ground:

Monitoring a Signal That Switches Between Any Voltage and Ground:

A. A.

Monitoring a Signal That Switches Between Any Voltage and Ground:Monitoring a Signal That Switches Between Any Voltage and Ground:

Device, Switch or Relay

EDC

Bus or any Voltage

Load

B. B.

Monitoring a Signal that is Switched to Ground:Monitoring a Signal that is Switched to Ground:

Monitoring a Signal that is Switched to Ground:

B. B.

Monitoring a Signal that is Switched to Ground:Monitoring a Signal that is Switched to Ground:

Bus

If a Load does not exist, an additional VI-221 must be placed in the circuit as shown. This provides a pullup for the switch.

VI-221

Light, Horn, etc.

Load

VI-221

Temp or Resistive Fuel

Level Channel.

EDC

Temp or Resistive Fuel

Level Channel.

Device, Switch or

Relay

2.8 Install the Interface Circuit for Flap and Trim Pots:

Elevator, Aileron and Rudder trim (as well as Flap position) can be monitored and displayed on the MVP. In most cases the position of these surfaces are monitored using a Ray Allen 5K ohm pot. The following circuit may be used to interface with a 1K to 100K pot.

4.99K, 1%, 1/4W Resistor

Bus

1K to

100K

Ray Allen

Pot

VI-221

Temp or Resistive Fuel

EDC

Level Channel.

2.9 Install the Interface Circuit for the Gear Position, Unsafe Indicator and Gear Warning:

The Gear Position and Unsafe Indicator shown on the MVP System Screen is intended as a backup to the aircraft’s existing system. The Gear Warning operates off the Gear Position, Unsafe Indicator, Airspeed and Manifold Pressure. The Gear Warning provides a voice warning to reduce the possibility of gear up landings.

Unsafe Indicator: Operates from an unsafe signal from the aircraft. Displays as either Red or Off on the MVP. The EDC interface circuit is shown below. The Unsafe Indicator is REQUIRED with any landing gear options listed below and requires one EDC input.

Landing Gear Position: There are three options for interfacing the EDC to the aircraft’s gear system.

Option 1: Connect the EDC to the aircraft’s Right, Left and Nose Gear green down lights. The state of each gear will be displayed independently on the MVP. Select Gear Left, RT and Nose for the probes in Configuration Screen #1. This option requires three EDC inputs. The EDC interface circuit is shown below.

Option 2: Connect the EDC to the aircraft’s Nose Gear green down light. The state of all three gears will be displayed on the MVP based on the Nose Gear’s state. Select “Gear All” for the probe in Configuration Screen #1. This option requires one EDC input. The EDC interface circuit is shown below.

Option 3: Use this option to display only the Left and Right Main Gears (no Nose Gear) from a single input. Connect the Left or Right Main Gear to the EDC as shown below. Select “Gear Main” for the probe in Configuration Screen #1. This option requires one EDC input. The EDC interface circuit is shown below.

Note: When setting colors, use Green for down and White for up. Red will cause an error.

Gear Up Warning: To provide a Gear Warning the MVP must monitor Gear Position, Airspeed and Manifold pressure. A voice warning is activated on the following logic:

((

(Any Gear is up

(( N1 is less than a set value.

Note: See the “Aircraft Number, Gear Warning and TAS Setup” screen to set values.

-OR--OR-

-OR- the Unsafe Indicator is on

-OR--OR-

Gear and Unsafe Interface Circuit

Tap into the switched side of the Light

VI-221

Gear or Unsafe Light

2.10 Install the CO Gaurdian CO Detector:

))

ANDAND

)

AND Airspeed is less than a set value

))

ANDAND

EDC

Temp or Resistive Fuel

Level Channel.

ANDAND

AND

ANDAND

Install the CO Guardian 353-201 Remote Mount CO Detector in accordance with the appropriate CO Guardian installation instructions supplied with the unit. The CO Detector connects to RS232 Port 3 on the MVP.

2.11 Install the Shunt:

An external shunt is a strip of metal, usually mounted on a bakelite base. This metal is made of special alloys to produce a very small, precise signal when current passes through it. It is not affected by temperature changes. If your aircraft currently has an external shunt you can calibrate your MVP to that shunt. The MVP will match any shunt on the market.

Install the External Shunt:Install the External Shunt:

Install the External Shunt:

Install the External Shunt:Install the External Shunt:

The external shunt should be installed in the starter-generator circuit and in an appropriate location that minimizes the routing of main cables. It should also be mounted in a location where inadvertent damage cannot occur. If the shunt can be accessed easily, it should be covered. When mounting the shunt, use self-locking or safety-wired nuts.

The signal wires from the shunt to the EDC must be fused a short distance after they leave the shunt. If this is a new installation, install two in-line oneamp fuses in each of the signal lines from the shunt to the EDC Amp Input.

Shunt

Note: If you are replacing an existing ammeter, the shunt may already be mounted in the aircraft. If you

already have a shunt installed and know the value of the existing shunt, the MVP can be calibrated to that shunt.

+ 55 hidden pages