Electronic Arts 040-0068-01 User Manual

EA SPORTS™ PGA TOUR® GOLF

CHALLENGE EDITION

Upgrade Kit Instructions

040-0068-01 Rev. B

© 2006 Electronic Arts Inc. Electronic Arts, EA, EA SPORTS and the EA SPORTS logo are trademarks or registered trademarks of Electronic Arts Inc. in the U.S. and/or other
countries. All rights reserved. PGA TOUR, PGA TOUR and Swinging Golfer design, TPC, TPC and Swinging Golfer design and TPC at Sawgrass are trademarks of PGA TOUR, INC. and
used by permission. Colonial Country Club name and logo are registered trademarks of Colonial Country Club. © 2004 Colonial Country Club. All rights reserved. . Bay Hill is a
trademark of TBHC, Inc Electronic Arts Inc. is the official licensee of St Andrews Links for EA SPORTS™ PGA TOUR
product are contributed towards the preservation and maintenance of the historic golf courses at St Andrews Links including the Old Course. Colonial Country Club name and logo
are registered trademarks of Colonial Country Club. Use of Sahalee name, mark and course description is with the permission of Sahalee Country Club. Plantation Course is a
trademark of Kapalua. All other trademarks are the property of their respective owners. EA SPORTS™ is an Electronic Arts™ brand. GLOBAL VR and the GLOBAL VR logo are
registered trademarks of Global VR, Inc. All other trademarks are the property of their respective owners.

Tournaments are not sponsored by or administered by Electronic Arts or the PGA TOUR.
GLOBAL VR IS AN AUTHORIZED ELECTRONIC ARTS DISTRIBUTOR.

! Read this manual before use.
! Keep this manual with the machine at all times.

www.globalvr.com

//

http:

service.globalvr.com
[e-mail]
[e-mail]
Phone: [phone]
Fax: [phone]

®

GOLF 2005. A portion of the proceeds from the sale of this

EA SPORTS™ PGA TOUR® Golf Challenge Edition Upgrade Kit

This kit upgrades your existing EA SPORTS™ PGA TOUR® Golf cabinet to run the new
Challenge Edition.

Upgrade Kit Contents

Part # Description

040-0068-01 Upgrade Instructions (This Document)
040-0062-01 System Manual
040-0063-01 Software Restore Guide
47004-00 Welcome Kit
050-0072-01* System Recovery Disk
050-0085-01* Game Install Disks (Two CDs)
45010-00 SmartCard Reader Assembly
H4-MEMOHASP Game Dongle
PGA05K-AW-01 Marquee Artwork
PGA05K-AW-02 SmartCard Reader Artwork
PGA05K-AW-09 Sub-Marquee Artwork
V3-USB-4P-HUB

*Part number may change due to software revisions.

4-Port USB Hub May be Included to Extend Length of SmartCard
Reader Cable

Upgrade Kit Contents

Primary Steps

1. Check BIOS (CMOS Settings).

2. Power OFF the cabinet and check the wiring.

3. Install the SmartCard Reader.

4. Install the SmartCard Dispenser (optional, separate kit).

5. Install the Software.

6. Test the dollar bill validator (DBV) and change wiring if necessary.

7. Install the Marquee Artwork.

8. Refer to the System Manual to register and set up your cabinet.

Tools Required

• Assorted Nutdrivers

• Screwdriver with Assorted Torx® and Phillips bits

• Scissors or Exacto® Knife

EA SPORTS™ PGA TOUR
Page 2 of 14 040-0068-01 Rev B 1/12/2006

®

Golf Challenge Edition Upgrade Kit

Check the BIOS (CMOS) Settings

Check the BIOS (CMOS) Settings

If you are comfortable using the CMOS Setup Utility, refer to the Key BIOS Settings sections
below. Otherwise, refer to Appendix A for detailed instructions.

Important: Look at the audio ports to determine which type of motherboard your computer has, as
described below.

Key BIOS Settings for NB32-SL Motherboard

The NB32-SL Motherboard has vertical audio ports. USB and Ethernet ports are located directly
below the keyboard and mouse connectors at the top of the panel.

Press the DEL key during boot to enter the CMOS Setup Utility. Select Load Optimized Defaults
from the Main Menu, and then change the following settings:

Menu Item Setting

Standard CMOS Features Halt On No Errors
Advanced BIOS Features

Integrated Peripherals PWR Loss Resume State Turn On

First Boot Device CDROM*
Second Boot Device HDD-0*
Third Boot Device Disabled*

*If a Floppy Disk Drive is installed, set Floppy as First Boot Device, CDROM as Second Boot

Device, and HDD-0 as Third Boot Device.

When finished, press F10 or select Save and Exit and press Enter. Select YES to confirm.

Key BIOS Settings for PS35-BL Motherboard

The PS35-BL motherboard has horizontal audio ports located directly under the USB and Ethernet
ports.

Press the DEL key during boot to enter the CMOS Setup Utility. Select Load Optimized Defaults
from the Main Menu, and then change the following settings:

Menu Item Setting

Standard CMOS Features Halt On No Errors
Advanced BIOS Features

Power Management Setup PWR Loss Resume State Turn On

First Boot Device CDROM
Second Boot Device Hard Disk
Third Boot Device Disabled
Memory Frequency For DDR266 Advanced Chipset Features
Dram R/W Timing Fast

When finished, press F10 or select Save and Exit and press Enter. Select YES to confirm.

© 2006 GLOBAL VR, INC.
040-0068-01 Rev B 1/12/2006 Page 3 of 14

Check Cabinet Wiring

Check Cabinet Wiring

Your cabinet must be properly wired and grounded to ensure safety and proper operation. Check all
connections and ground wires. Symptoms of inadequate grounding may include loss of trackball,
coin input problems, and the computer freezing. It is a good practice to purchase an AC Outlet
Circuit Tester from a hardware store, and follow the manufacturer's instructions to check the cabinet
power strip and your wall outlet for proper grounding and polarity.

For cabinets with the Style A power plate, as shown in Figure 1, perform the steps that follow to
check the connections on the AC power plate, and add a ground

ground lug (as required). These steps will help to ensure that grounding is adequate for the coin
mech and trackball.

(earth) wire to the coin vault

Figure 1. Power Plate Styles

WARNING: ELECTRIC SHOCK HAZARD. Disconnect the cabinet power cord
before performing the steps in this document.

The steps below apply only to cabinets with the Style A power plate, as shown in Figure 1.

1. Disconnect the power cord from the cabinet.

2. Remove the four power plate mounting nuts and bolts and remove the power plate. If a grounding
wire is connected to one of the mounting bolts, this is not an adequate ground. Connect that wire to
the ground lug on the EMI filter, as described in the next part of this document.

EA SPORTS™ PGA TOUR
Page 4 of 14 040-0068-01 Rev B 1/12/2006

®

Golf Challenge Edition Upgrade Kit

Check Cabinet Wiring

3. Refer to Figure 2 and inspect the power plate to make sure that the correct color wire is connected to
each connector.

4. Inspect your cabinet to see if there is a ground wire from the ground lug on the EMI filter to the
ground lug on the coin vault. If the wire is present, make sure it is tightly connected. Otherwise,
perform the following steps to install a ground wire.

Figure 2. Power Plate Connections

a. Install a 2 1/2' ground wire to the lug on the right of the EMI filter, as shown in Figure 2. Use a

#8-32 kep nut to secure it in place. Secure the nut tightly.

b. Connect the other end of the wire to the ground lug on the coin vault (coin box). Use a #8-32

kep nut to connect the ground wire on top of the other ground wires, as shown in Figure 3.
Secure the nut tightly.

c. Confirm the following wires are connected to the coin vault ground lug:

• One wire from coin vault to coin door

• One wire from coin vault to trackball

Important: All ground wires must be secured tightly!

Figure 3. Coin Vault Ground Lug

© 2006 GLOBAL VR, INC.
040-0068-01 Rev B 1/12/2006 Page 5 of 14