Electrolux TRIMKITSS2 Instruction Manual

U19 All Refrigerator and All Freezer Trim Kit Installation

Product Line: U19 All Refrigerator and All Freezer Models

Models: EI32AR65JS E32AR75JPS EI32AF65JS E32AF75JPS

Serial Number Range: All Serial number ranges

Single Trim Kit Components

Parts Included in Kit TRIMKITSS1 (Part# 297333510):

Kit for Models: EI32AR65JS and EI32AF65JS E32AR75JPS and E32AF75JPS

Single Trim Kit 297333510

ITEM PART NUMBER DESCRIPTION QTY 1 297349010 Trim Side RH U19 1 2 297349011 Trim Side LH U19 1 3 297332711 Trim Top Short U19 Single 1 4 297332811 Trim Top Tall U19 Single 1 5 297333311 Kick Plate U19 Sngle 1 6 297337700 Carton, Packaging 1 7 297343201 Hardware Pack Single U19 1 8 297276900 Lever Assembly Support System 2

INSTRUCTION SHEET

Single Trim Kit

NOTE: All Hardware Pack components mentioned

throughout this instruction sheet will have an “H” after the item number.

Front View

Hardware Pack 297343201

ITEM PART NUMBER DESCRIPTION QTY 1H 297333900 Tie-Bar Hinge 1 3H 297236250 Screw 1/4-20 x .63 8 5H 050149 Screw TH #8-18 x .75 AB 6 6H 297142600 Screw FH #8-32 x .63 2 7H 297299700 Installation Instructions 1

8

1 2

4

3

5

Hardware Pack 297343201

1.25” Ref

6.25” Ref

2.62” Ref

1H

2H

3H4H 5H6H

Dual Trim Kit Components

Parts Included in Kit TRIMKITSS2 (Part# 297333610):

Kit for Models: EI32AR65JS and EI32AF65JS E32AR75JPS and E32AF75JPS

Double Trim Kit 297333610

ITEM PART NUMBER DESCRIPTION QTY 1 297336900 Center Trim U19 1 2 297349010 Trim Side RH U19 1 3 297349011 Trim Side LH U19 1 4 297332710 Trim Top Short U19 Dual 1 5 297332810 Trim Top Tall U19 Dual 1 6 297333310 Kick Plate U19 Dual 1 7 297337700 Carton, Packaging 1 8 297343200 Hardware Pack Dual U19 1 9 297276900 Lever Assembly Support System 4

INSTRUCTION SHEET

Double Trim Kit

Front View

NOTE: All Hardware Pack components mentioned throughout this instruction sheet will have an “H” after the item number.

9

1

2

3

5

4

6

Hardware Pack 297343200

ITEM PART NUMBER DESCRIPTION QTY 1H 297333900 Tie-Bar Hinge 2 2H 297333901 Tie-Bar Back 1 3H 297236250 Screw 1/4-20 x .63 18 4H 297337000 Screw FH 1/4-20 x .63 4 5H 050149 Screw TH #8-18 x .75 AB 8 6H 297142600 Screw FH #8-32 x .63 2 7H 297299700 Installation Instructions 1

Hardware Pack 297343200

TRIMKITSS1 (Part# 297333510) Trim Kit Dimensions

INSTRUCTION SHEET

75.09”

(1907 mm)

25.25”

(641mm)

(min.)

(882 mm)

33.00 ± .032”

(838 ± .8mm)

34.74”

75.00 ± .06” (1905 mm)

79.00 ± .06” (2006.5 ± 1.5mm)

25.25”

(641mm)

(min.)

33.00 ± .032”

(838 ± .8mm)

34.74”

(882 mm)

79.09”

(2009 mm)

TRIMKITSS2 (Part# 297333610) Trim Kit Dimensions

75.00 ± .06” (1905 mm)

INSTRUCTION SHEET

79.00 ± .06”

(2006.5 ± 1.5mm)

”

75.09”

(1907 mm)

(641mm)

67.12”

(1705 mm)

25.25”

min.

66.00 ± .032

(1676.4 ± .8mm)

25.25”

(641mm)

min.

67.12”

(1705 mm)

66.00 ± .032

(1676.4 ± .8mm)

79.09”

(2009 mm)

Safety: Always wear safety glasses when using power tools.

Tools Needed:

• PhillipsTM Screwdriver • Adjustable Wrench to t 1-1/4” • Step Ladder

• Flathead Screwdriver • 3/8” Socket Wrench • Tape Measure (min. 7” length)

• Safety Glasses • 7/16” Socket Wrench • Drill & 1/8” Bit

Before You Begin

• Be careful when unpacking components. Do not use sharp objects when removing packaging material. This may

scratch the surface of trim components.

• Use extreme care when handling the metal trim pieces. Corners are very sharp and easily damaged if dropped.

INSTRUCTION SHEET

Setting Up The Trim And Grill Assembly (Single and Dual Installations)

1. Lay the parts out on a cleared area face down. Be

sure to place a drop cloth over the floor to prevent

scratching trim kit and/or floor. (See Figure 1).

Figure 1.

2. Cut 4” (101.6mm) off the left and right Side Trim

using the slot as a guide to make the proper size for

a 75” (1905mm) cut-out. (See Figure 2).

Leveling System Install (Single and Dual Installations)

3. a. Lie unit on its back on packaging material or a

drop cloth to prevent damage.

b. Remove (3) screws from each side and discard. (See Figure 3)

c. Remove and save both plastic leg levelers to use

in the next step.

Remove Leg Levelers

Remove And Discard

Screws

Remove Leg Levelers

NOTE: DO NOT cut the side trim if installing in a 79”

(2006mm) opening.

Side Trim

Left and

Right Sides

Figure 2.

Figure 3.

4. a. Attach the current leg leveler to leveling system.

The leg leveler is a common part that will work

on both bottom sides of the unit. (See Figure 4).

b. Attach leg leveler with three (3) screws per side

using a 3/8 socket.

c. Re-install the leg levelers.

d. In order to provide clearance to access the rear

screw hole, adjust the rear roller up out of he

way. When finished, lower the rear roller back to

its initial position.

Install Leg Levelers

Install Screws (3 per side)

Figure 4.

Trim Kit Installation

Installing Trim Kit Tie Bar (Dual Installation Only)

NOTE: Leveling may be required to line up the holes in steps “a” and “d”.

5. a. Tie units together by securing the mounting

bracket at the back of the units with a

3/8” socket. (See Figure 5).

b. Install center strip to insure the proper 3/8” gap

is maintained between units. (See Figure 6).

c. Tie units together with the common mounting

bracket at the front top with two screws in the inner two screw holes by using a 3/8” socket.

(See Figure 7)

d. Tie units together with common mounting

bracket at the bottom front using #3 Phillips

driver. (See Figure 8)

3/8” Gap

INSTRUCTION SHEET

Item 1H

Figure 8.

Trim Kit Installation (Single Unit Installation)

6. Remove outer screw from top hinge using a 3/8”

socket driver or wrench and save for later. Install mounting bracket with one screw mounted to inside

hole using a 3/8” socket. (See Figure 9).

Item 2H

3/8” Center Strip

Item 1 Dual kit

Figure 5.

3/8” Gap Between Units

Figure 6.

Item 1H

3

H

Figure 9.

Remove Screw

Side Trim Installation (Single and Dual Installations)

7. a. Position Left Hand Side Trim on cabinet trim with

bottom resting on the floor.

b. Drill the 1/8” (3mm) pilot hole.

c. Run screw in all the way and then back out.

Remove side trim for later install.

(See Figure 10).

Figure 7.

NOTE: Some cabinet substrates may require pre-drilling

holes using a 1/8” (3mm) diameter drill bit.

INSTRUCTION SHEET

8. a. Position Right Hand Side Trim on cabinet trim

with bottom resting on the floor.

b. Drill the 1/8” (3mm) pilot hole.

c. Run screw in all the way and then back out.

Remove side trim for later install.

(See Figure 10).

H

Figure 10.

Top Trim Install (Single and Dual Installations)

10. 75” (1905mm) High Opening With Top Trim (Single and Dual Installations)

a. Slide units into place. Adjust height so top trim

height reaches 75.09” (1907mm). Center units in opening and level. (See Step 12 for leveling instructions)(See Figures 13 and 14)

b. Drill 1/8” (3mm) pilot holes and fasten screws

with a Phillips driver to kitchen cabinets.

Figure 13.

NOTE: Step ladder required for installing top trim

components.

9. a. Remove outer hinge screw common on both

sides for a dual installation, (for a single

installation this screw is removed in Step 6.

Align the top trim and attach with a 3/8” socket.

Repeat for opposite side. (See Figure 11).

b. (Dual installation only) Install outer screws on

common mounting bracket, align top trim and

attach with 3/8” socket. (See Figure 12).

Figure 11.

H

Figure 14.

11. 79” (2006mm) High Opening With Louvered Top

Trim (Single and Dual Installations)

a. Slide units into place. Adjust height so top trim

height reaches 79.09” (2009mm). Center units in opening and level. (See Figure 15)

b. Drill 1/8” pilot holes and fasten two (2) screws

per side with a Phillips driver to kitchen cabinets.

Figure 12.

Figure 15.

INSTRUCTION SHEET

12. Trim Kit Leveling (See Figure 16) (Single and Dual Installations)

a. To raise front of unit, turn leg leveler to left with

adjustable wrench to fit 1-1/4” hex.

b. To raise back of unit, adjust bolt clockwise with

3/8” socket or flat head screwdriver

To raise or lower door,

adjust 7/16” bolt.

3/8” Bolts

Phillips Head

Screws

To raise back of

unit, adjust bolt

clockwise.

Leg Leveler

Figure 16.

14. Side Trim Attachment to Kitchen Cabinets (Single and Dual Installations)

a. Fasten bottom of side trim with screw.

(See Figure 17) b. Fasten screws to top trim. (See Figure 18)

Figure 17.

13. Hinge Adjustment (See Figure 16)

(Single and Dual Installations)

a. The bottom hinge is designed to make final

minor adjustments for door to door and door to

cabinet alignment.

b. Hinge will move side to side 3/32” and raise up

1/8”.

Use a 7/16” socket or open end wrench to raise or

lower the door.

Use a 3/8” socket and a Phillips screwdriver to

loosen bottom hinge. Shift door left or right, then retighten screws and bolts.

Figure 18.

15. Kick Plate Attachment

(Single Unit) Attach the kick plate to the cabinet with

two (2) screws. (See Figure 19)

(Dual Unit) Attach the kick plate to the cabinet with

four (4) screws. (See Figure 20)

Figure 19.

Screws

Figure 20.

Electrolux TRIMKITSS2 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual