Electrolux TINSEB504MRR0 User Manual

MICROWAVE WALL OVEN INSTALLATION INSTRUCTIONS

to top of cp angle

(59.8 cm)

23 ½"

20 ¾"

(52.7 cm)

18"

Installation and service must be performed by a qualiﬁed installer.

IMPORTANT: Save for local electrical inspector's use.

Read and Save these instructions for future reference.

The electrical requirements for this oven are 120 volts, 15 amps.

NOTE

Base must be capable of supporting 150 pounds (68.0 1. kg) for the Microwave Wall Oven only.

Make sure base is level and front of cabinet is square. If 2. the cabinet base is not level, the oven will tend to slide out when opening the door.

Minimum required distance is 36" (91.44 cm) from the 3. ﬂo or.

The outlet should not be located in the shaded area of 4. Figure 1. It is required the outlet be a dedicated 120 volts with a 15amp rating for the appliance.

Minimum required distance between the Microwave 5. Oven and th e wall o ven cu touts sh ould be a t least 3" leaving a 2" visible space between both produc t faceplates. Due to lower vent overlap, the visible space between units will be 1".

Figure 1

PRODUCT DIMENSIONS

MODEL A B C D

27" (68.8) Microwave 27" (68.8) 221/4" (56.5) 247/8" (63.2) 21

30" (76.4) Microwave 30" (76.4) 221/4" (56.5) 273/8" (69.5) 21

30" (76.4) Convection

Microwave

MODEL Min. F Max. G Min. H Max. I

27" (68.8) Microwave 251/8" (63.8) 255/8" (65.1) 24" (61.0) min. 21"(53) 211/2"(54.6) 27" (68.8) min.

30" (76.4) 22" (55.9) 28" (71.1) 21

CUTOUT DIMENSIONS AND CABINET WIDTH

/16" (55.1)

30" (76.4) Microwave 275/8" (70.2) 281/8" (71.4) 24" (61.0) min. 21"(53) 211/2"(54.6) 301/8" (76.5) min.

30" (76.4) Convection

Microwave

All dimensions are in inches (cm).

281/2"(72.4) 29" (73.7) 24" (61.0) min. 21"(53) 211/2"(54.6) 301/8" (76.5) min.

TINSEB504MRR0

MICROWAVE WALL OVEN INSTALLATION INSTRUCTIONS

Safety

Door Latch

Hinge

Oven Cavity

Waveguide Cover

Door Seals

and Sealing

Surfaces

IMPORTANT NOTES TO THE INSTALLER

Read all instructions contained in these installation 1. instructions before installing the Microwave Wall Oven. This oven can be built into a cabinet or wall by itself or above any electric wall oven or warming drawer.

Remove all packing material from inside the oven cavity 2. before connecting the electrical supply to the Microwave Wall Oven. DO NOT REMOVE THE WAVEGUIDE COVER, which is located on the cavity ceiling. See Figure 2A.

IMPORTANT SAFETY INSTRUCTIONS

Never use your appliance for warming or heating the room. Prolonged use of the oven without adequate

ventilation can be dangerous.

Carpentry

Refer to Figure 1 for the dimensions required for your appliance, and the space necessary to install the oven. The oven support surface should be solid plywood or similar material, the surface must be level from side to side and from front to rear.

Electrical Requirements

The appliance operates on a 120 volt, 60 Hz electrical supply with a separate ground wire. Provide a separate circuit with a fuse or circuit breaker rated for 15 amps.

Observe all governing codes and local ordinances

IMPORTANT NOTE TO THE CONSUMER

Keep these instructions with your Owner's Guide for future reference.

Figure 2A Figure 2B

Remove the 2 shipping duct supports (see Figure 2B) by 3. removing the 2 screws securing each side. Reinsert 2 screws (each side) to secure the stainless cover.

Remove the feature sticker, if there is one, from the 4. outside of the door.

Check the oven for any damage, such as misaligned or 5. bent door, damaged door seals and sealling surfaces, broken or loose door hinges and latches and dent inside the cavity or on the door.

If there is any damage, DO NOT operate the oven and contact your dealer or ELECTROLUX AUTHORIZED SERVICER.

Observe all governing codes and local ordinances.6.

Be sure to leave these instructions with the consumer.7.

To prevent damage to the oven control, during cold tempera ture w eathe r, wait at least th ree (3) hour s af ter receiving this oven before supplying power to the appliance. This will prevent possible damage to the built-in oven control at power on.

Cabinet Installation

The Microwave Wall Oven can tip when the door is open. The Anti-Tip brackets supplied with the Microwave Wall Oven mu st be attached to the cabinet and the appliance to prevent tipping of the unit and injury to persons.

ANTI-TIP BRACKETS INSTALLATION INSTRUCTIONS

Unpack the Microwave Wall Oven and find the 2 1. Anti-Tip brackets and screws included in the literature package.

Install the Anti-Tip bracket in the cabinet as shown 2. on Figure 3. Note: To prevent damage to cabinet, it is recommended to drill ¹/16" (0.16 cm) diameter pilot holes before installing the Anti-Tip brackets.

MICROWAVE WALL OVEN INSTALLATION INSTRUCTIONS

Anti-Tip Bracket

installed in cabinet

Oven removed

from the cabinet

Oven

Bracket

released

Cabinet

Oven

Right Side

Tool supplied

Anti-Tip

Bracket

Anti-Tip Brackets

16-1/2"

(41.9 cm)

Cutout Width

(See dimensions below)

30-INCH MICROWAVE Cutout Width

27-5/8" (70.2 cm) Min.* 28-1/8" (71.4 cm) Max.* 27-7/8" (70.8 cm) Recommended*

30-INCH CONVECTION Cutout Width

28-1/2" (72.4 cm) Min.* 29" (73.7 cm) Max.* 28-3/4" (73.0 cm) Recommended*

27-INCH MICROWAVE Cutout Width

25-1/8" (63.8 cm) Min.* 25-5/8" (65.1 cm) Max.* 25-3/8" (64.5 cm) Recommended*

Cutout Height 21" (53.3 cm) Min.* 21-1/2" (54.6 cm) Max.*

MICROWAVE WALL OVEN INSTALLATION

Two persons are required to install the oven. N ever hold the door handle when moving the oven.

Place the oven adjacent to the opening on a table or 3. stand. Plug the power supply cord into the electrical outlet. Carefully guide the oven into the prepared opening. Avoid pinching cord between oven and wall. See Figure 4. Push the unit in and against the cabinet. The oven side bracket will clip into the Anti-Tip brackets. See Figure 3.

To pull out the oven for servicing, open the door and 4. locate the two holes on the side frame. Simultaneously insert the tools provided with the appliance in both holes and pull the oven towards you. See Figure 5.

ANTI-TIP BRACKET INSTALLATION

FINISHED ANTI-TIP BRACKET INSTALLATION

Figure 3

REMOVING OVEN FOR SERVICING

Figure 4

Figure 5

MICROWAVE WALL OVEN INSTALLATION INSTRUCTIONS

Serial Plate

Menu Label

Model and Serial Number Location

The serial plate is located on the oven front frame. See Figure 6.

When ordering parts for or making inquires about your oven, always be sure to include the model and serial numbers and a lot number or letter from the serial plate on your oven.

PRODUCT IDENTIFICATION

Figure 6

Before You Call for Service

Refer to the warranty in your Use & Care Guide for our toll-free service number and address. Please call or write if you have inquiries about your product and/or need to order parts.

+ 8 hidden pages