Electrolux EXWADREW120 Installation manual

EN FRONT LOAD WASHER FR LAVEUSE Á CHARGEMENT FRONTAL ES LAVADORA DE CARGA FRONTAL

INSTALLATION INSTRUCTIONS INSTRUCTIONS D’INSTALLATION INSTRUCCIONES DE INSTALACIÓN

IMPORTANT SAFETY INSTRUCTIONS

WARNING

Please read all instructions before using this washer.

Recognize safety symbols, words and labels

Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type as described below:

Definitions

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

IMPORTANT

IMPORTANT indicates installation, operation or maintenance information which is important but not hazard-related.

Installation Checklist

Shipping Hardware

 Foam shipping support (in door gasket) removed

and stored

 Shipping bolts and spacers removed from rear of

appliance and stored

 Hole plugs (shipped in bag in drum) installed in

holes in backsheet

Leveling

 Washer is level, side-to-side and front-to-back  Cabinet is setting solid on all corners

Water Supply

 Use only new hoses and verify rubber sealing

washers are installed

 HOT supply is connected to HOT inlet and COLD

supply is connected to COLD inlet

 HOT and COLD water supply turned on  No leaks present at water supply connections or

appliance inlet connections recheck in 24 hours

Drain

 Stand pipe or wall drain height minimum 24”  Drain hose snapped in “U” channel (shipped in

drum)

 Drain hose secured in place with cable tie (shipped

in drum)

Electrical Power

House power turned on  Washer plugged in

Final Checks

 Installation Instructions and Use and Care Guide

read thoroughly

 Door locks and water enters drum when cycle starts  Registration card sent in

TABLE OF CONTENTS

Important Safety Instructions ..............................................2-3

Installation Requirements ...................................................4-5

Installation Instructions .......................................................6-9

Accessories ......................................................................... 10

Notes ................................................................................... 11

Français ...............................................................................12

Español ................................................................................ 22

IMPORTANT SAFETY INSTRUCTIONS

NOTE

The electrical service to the washer must conform with local codes and ordinances and the latest edition of the National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian Electrical Code C22.1 part 1.

WARNING

Destroy the carton and plastic bags after the washer is unpacked. Children might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers causing suffocation. Place all materials in a garbage container or make materials inaccessible to children.

SUFFOCATION HAZARD

CAUTION

To avoid back or other injury, have more than one person move or lift the washer.

EXCESSIVE WEIGHT HAZARD

IMPORTANT

The instructions in this manual and all other literature included with this washer are not meant to cover every possible condition and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and maintaining any appliance.

Maximum benefits and enjoyment are achieved when all the Safety and Operating Instructions are understood and practiced as a routine with your laundering tasks.

IMPORTANT

DO NOT INSTALL YOUR WASHER:

1 ... in an area exposed to dripping water or outside

weather conditions. The ambient temperature should never be below 60° F (15.6° C) to maximize detergent effectiveness.

2 ... in an area (garage or garage-type building) where

gasoline or other flammables (including automobiles) are kept or stored.

3 ... on carpet. Floor MUST be solid with a maximum

slope of 1 inch (2.5 cm). To minimize vibration or movement, reinforcement of the floor may be necessary.

WARNING

For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or loss of life. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

FIRE HAZARD

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Tools and materials needed for installation:

Adjustable

wrench

3/8” or 10 mm

box wrench

Ratchet and

socket set

Inlet hose (x2)

Hoses are not included with washer purchase. See “Accessories” section for various inlet hose kits to fit your specific installation.

AND ANDOROR OR

NOTE

Optional universal wrench available from

dealer

Adjustable

pliers

Carpenter’s level

Installation Requirements

Grounding type

ll receptacle

wer cord with

3-prong grgr

ounded plug

Do not,

under

y cir

cumstances,

cut,

removeve,

or b

ypass the

ounding pr

ong.

Electrical system requirements

CIRCUIT - Individual, properly polarized and grounded 15

amp. branch circuit fused with 15 amp. time delay fuse or circuit breaker.

POWER SUPPLY - 2 wire, with ground, 120 volt single phase,

60 Hz, Alternating Current.

NOTE

Because of potentially inconsistent voltage capabilities, the use of this washer with power created by gas powered generators, solar powered generators, wind powered generators or any other generator other than the local utility company is not recommended.

OUTLET RECEPTACLE - Properly grounded 3-prong

receptacle to be located so the power supply cord is accessible when the washer is in an installed position.

Grounding type wawall receptacl

PoPower cord with 3-prong

Do not, anany cir cut, or b

ypass th

grgrounding pr

ounded plug

under

cumstances,

remo

ong.

NOTE

GFI (Ground Fault Interrupter) receptacle is not required.

Water supply requirements

Hot and cold water faucets MUST be installed within hose length of your washer’s water inlet. The faucets MUST be 3/4 inch (1.9 cm) with threading for laundry hose connection. Water pressure MUST be between 10 and 110 psi. Pressure difference between hot and cold cannot be more than 10 psi. Your water department can advise you of your water pressure.

Drain system requirements

1 Drain capable of eliminating 6 gals (22.5 L) per minute.

2 A standpipe diameter of 1-1/4 in. (3.18 cm) minimum.

3 The standpipe height above the floor should be:

Minimum height: 24 in. (61 cm)

Maximum height: 56.5 in. (144 cm)

56.5”

(144cm)

max.

24”

(61cm)

min.

Ground requirements

WARNING

Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded.

1 The washer MUST be grounded. In the event of

2 Since your washer is equipped with a power supply

ELECTRICAL SHOCK HAZARD

malfunction or breakdown, grounding will reduce the risk of electrical shock by a path of least resistance for electrical current.

cord having an equipment-grounding conductor and a grounding plug, the plug MUST be plugged into an appropriate, copper wired receptacle that is properly installed and grounded in accordance with all local codes and ordinances or in the absence of local codes, with the National Electrical Codes, ANSI/NFPA 70 (latest edition). If in doubt, call a licensed electrician. DO NOT cut off or alter the grounding prong on the power supply cord. In situations where a two-slot receptacle is present, it is the owner’s responsibility to have a licensed electrician replace it with a properly grounded three prong grounding type receptacle.

Clearance requirements

MINIMUM INSTALLATION CLEARANCES - Inches (cm)

SIDES REAR TOP FRONT Alcove 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a Under Counter 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a

0”

(0cm)

0”

(0cm)

0”

(0cm)

Washer Dimensions

42” (107 cm)

to clear open door

25” (64 cm)

to front of closed door

Installation Requirements

24”

(60.5 cm)

freestand washer

on floor

floor line

washer mounted on

optional pedestal

floor line

to clear open door

43” (109 cm)

26” (66 cm)

to front of closed door

water supply connection on rear of unit

24”

(60.5 cm)

drain hose on rear of unit

power cord on

rear of unit

electrical supply on rear of unit

drain hose on rear of unit

(85 cm)

33.5”

46”

(116.5 cm)

floor line

Drain hose length on washer approximately 55 inches (140 cm).

Power supply cord length on washer approximately 59 inches (150 cm).

Power supply cord length on Canadian dryer approximately 59 inches (150 cm).

power cord on

rear of unit

68.5”

(174 cm)

Installation Instructions

Removing foam packaging

WARNING

1 Remove door tape and empty drum contents, including

foam shipping brace inside rubber gasket of door.

2 Using a foam corner post from the packaging to protect

the floor, carefully lay the washer on its back.

SUFFOCATION HAZARD

CAUTION

To avoid back or other injury, have more than one person move or lift the washer.

3 Remove styrofoam base and set it aside. 4 Carefully return the washer to an upright position. 5 Carefully move the washer to within 4 feet (1 m) of its

EXCESSIVE WEIGHT HAZARD

final location.

IMPORTANT

Save styrofoam base and shipping braces for use to help prevent washer damage during any future moves.

x 2

Releasing Drain Hose

Removing shipping hardware

Installation Instructions

The drain hose is secured in place with two plastic latching clamps. Press the locking tab and release the drain hose.

Remove all of the following from the back of the washer:

• 3 shipping bolts

• 2 plastic clamps

• 3 shipping spacers

x 3

Installing hole plugs

Locate hole plugs in the small bag supplied with washer instruction guides. Cut them apart from each other and insert them in the holes in washer back panel.

x 2

NOTE

Rubber expansion material on spacers may need time to relax before they can be easily pulled through shipping hole.

x 3

IMPORTANT

Save all shipping bolts and spacers for future use. If the washer is to be transported at a later date, the shipping hardware must be reinstalled to help prevent shipping damage.

Installation Instructions

Leveling your washer

Excessive noise and vibration can be prevented by properly leveling the washer.

1 For free standing installation and with the washer within

4 feet (1 m) of its final location, place a level on top of the washer.

2 Use adjustable pliers to adjust the leveling legs so the

washer is level front-to-rear and side-to-side, and stable corner-to-corner.

3 Press down on alternate corners and sides and feel for

the slightest movement. Adjust the appropriate leg(s) so the washer sits solidly on the floor on ALL four legs. Keep the leveling leg extension at a minimum for best performance of the washer.

NOTE

For pedestal installations, see additional installation instructions included with the pedestal.

Connecting inlet water

1 Run some water from the hot and cold faucets to flush

the water lines and remove particles that might clog the water valve screens and to determine which faucet is hot and which is cold supply.

raise

lower

RUBBER WASHERS MUST BE PRESENT

USE ONLY

NEW HOSES

NOTE

Hoses are not included with washer purchase. See “Accessories” section for various inlet hose kits to fit your specific installation.

2 Connect the HOT inlet hose to the HOT inlet connection

on the washer and the COLD inlet hose to the COLD inlet connection on the washer. Tighten by hand until snug. Then tighten each supply connection another 2/3 turn with pliers. Do not cross thread or over-tighten

these connections.

3 Connect the HOT inlet hose to the HOT water supply

and the COLD inlet hose to the COLD water supply. Tighten by hand until snug. Then tighten each supply connection another 2/3 turn with pliers. Do not bend,

kink or pinch water inlet hoses.

4 Turn on the water and check for leaks.

COLD

HOT

Grounding type

ll receptacle

wer cord with

3-prong grgr

ounded plug

Do not,

under

y cir

cumstances,

cut,

removeve,

or b

ypass the

ounding pr

ong.

Connecting drain and electrical

1 Snap one end of the drain hose hanger (shipped in

washer drum) onto the drain hose. Continue wrapping it around the hanger and snap it in place.

2 Place the hook end of the drain hose in the drain

opening. Secure the drain hose with the cable tie (provided in the enclosure package) to the standpipe, inlet hose, laundry tub, etc. so the hose does not pull out from the force of the water.

IMPORTANT

Check to ensure the power is off at a circuit breaker/fuse box before plugging the power cord into an outlet.

3 Plug the power cord into a grounded outlet.

Grounding type wawall receptacl

Do not,

under

anany cir

cumstances,

cut,

remo

or b

ypass th

grgrounding pr

ong.

Installation Instructions

PoPower cord with 3-prong

ounded plug

4 Turn on the power at a circuit breaker/fuse box. 5 Carefully slide the washer to its final position. Recheck

for level and rock corners for stability. Remove and discard door tape.

6 Read the Use & Care Guide provided with the washer. It

contains valuable and helpful information that will save you time and money.

7 If you have any questions during initial operation,

please review the “Service Prevention Checklist” in your Use & Care Guide before calling for service.

8 Place these instructions in a location near the washer

for future reference.

NOTE

A wiring diagram and technical data sheet are located under the washer top panel, on top of the detergent dispenser housing.

CABLE TIE

Accessories

MATCHING STORAGE PEDESTAL*

White Pedestal - P/N EPWD200QSW

A storage pedestal accessory, specifically designed for this washer may be used to elevate the washer for ease of use.

*Other colors may be available. Contact the source where you purchased your washer.

DRYER STACKING KIT

P/N STA9

Depending on the model you purchased, a kit for stacking a matching dryer on top of this washer may have been included in the initial purchase of your dryer. If your model did not include a stacking kit or you desire another stacking kit, you may order one.

INLET HOSE KITS

Please call 866-233-8353 (in Canada, 800-265-8352) to explore hose kit options that will meet your specific installation needs.

UNIVERSAL APPLIANCE WRENCH

P/N 137019200

A UNIVERSAL APPLIANCE WRENCH is available to aid in dryer/washer/pedestal feet adjustment.

CAUTION

Failure to use accessories manufactured by (or approved by) the manufacturer could result in personal injury, property damage or damage to the washer.

Replacement parts:

If replacements parts are needed for your washer, contact the source where you purchased your washer or refer to your

and Care Guide

for more information.

Use

WARNING

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

ELECTRICAL SHOCK HAZARD

+ 22 hidden pages