Electrolux EIDW6105GB0, EIDW6105GB1, EIDW6105GB1A, EIDW6105GB2B, EIDW6105GS0 Installation Guide

...

Dishwasher

Installation Instructions

Printed in U.S.A.

154671001

02/08

INSTALLER: Leave Installation Instructionswith owner. OWNER: Read your dishwasher Use and Care Manual. It contains

important safety information for operating this appliance. It also has many suggestions for getting the best results from your dishwasher.

Read all instructions before installing dishwasher.

For your safety, please read and observe all safety

instructions. This guide will help you anticipate drain, water, and

electrical connections, and help you select the best location for the dishwasher.

Tip Over Hazard

Do not use dishwasher until completely installed. Do not push down on open door. Failure to follow this warning can result in serious

injury.

Cut Hazard

To prevent serious injury from sharp edges, wear work gloves when handling, unpacking or disassembling unit.

Tools and Materials Needed for

Installation (NotIncluded)

Drill, Electric Driver, Socket 5/s2",1/4",5/16"

Flaring Tool / Tube Cutter (for copper tubing) Flashlight

Level Pipe Joint Compound (for iron pipe plumbing) or

Pipe Thread Tape (for sealing threads)

• Pliers

• Safety Glasses

• Saw, Keyhole or V2",11/2"to 2" Hole Cutters

• Screw Drivers, Slotted and #2 Phillips (magnetic tip preferred)

• Tape, Electrical or Duct

• Tape, Measuring

• Wire Stripper or Utility Knife

• Wrench, Hex-end

• Wrenches, 2 Adjustable (for copper tubing) or2 Pipe wrenches (foriron pipe plumbing)

Parts You Will Need* (Not Included)

• Drain Hose Clamp, 1'h" Diameter

• Brass Elbow, 90° with a s/s"National Pipe Thread

• Conduit Connector (UL Listed)

• Wire Nuts, three (3) for 12-14 gauge wire (UL Listed)

If required:

• "Y" Branch Tailpieceand

Connector Kit (See Step 4)

• Air Gap Kit (See Step 4)

All the parts can be found at local hardware, electrical and plumbing supply stores.

NOTE: Put unit on its back being careful not to pinch the Water Drain Hose.

1. Remove two (2) screws at front of the kickplate assembly using a

#2 Phillips screw driver.

2. Tilt and pull forward to remove see figure 1.

NOTE: It is not necessary to remove the outer door for installation.

lilckplate Assembly

Outer Door

Top Screws

Toeplate

Kickl:

Figure !

Locate water inlet valve behind kickplate on bottom left underside of unit.See Figure 4. The valve has a 3/8"NPT female fitting.

Remove Plug

Wrap 90° elbow (not included) with pipe thread tape (or apply

joint compound) and thread it into water inlet valve. When

tightened, elbow should point toward the left. To prevent bending of bracket or breaking ofvalve, avoid overtightening.

See Figure 4.

Cabinet Preparation: As a precaution, it is recommended, but not required that the cabinets enclosing all sides of the dishwasher (including the underside of the countertop) be sealed with an oil based paint or moisture-proof polyurethane to prevent possible steam/ moisture damage.

Electric Shock Hazard

Observe all local codes and ordinances for electrical and plumbing connections. All electrical

and plumbing work should be performed by qualified persons. Failure to follow this warning could result in death or serious injury.

1. Make sure your location has the correct drain, water, and electrical outlets to make the connections. Do not install unit

under a cooktop range. Damage to tub or other components will

occur.

Electrical, water,

34"

rain.

35"

maxf*

3I/2"min.to 41/2"max. -1a/4"

Front

13/4"

and drain lines

must be confined

to shaded area.

Preferred

Drain Areas

**NOTE:

35" max. height for

standard cabinetry cutout.

(s/,_,min. clearance

required from unit to

underside of countertop.)

Left

/ Doorin900

openposition

Right

497/_''

",_ 22//'--

IMPORTANT: For proper operation and appearance of unit, cabinet opening should have dimensions as shown in Figure 2.

If unit is to be placed in a corner, there must be at least a 2-inch

side clearance to open door.

2. Floor should be flat and free of any obstruction.

IMPORTANT: Drain, water, and electrical lines should be roughed-in before going any further.

Electric Shock Hazard

Electrical, water, and drain lines must be confined

to shaded areas in Figure 2.

Electric conductors, water, and drain could be

damaged.

Failure to follow these instructions could result in

fire or electric shock.

NOTE: If dishwasher is installed at end of a cabinet, sides and

back must be fully enclosed.

NOTE: Cabinet Seal Kit (Kit # 154662101). This kit provides a

seal between the unit and cabinets once installation is complete. (The Installation Instructions are located in the Kit)

Locating the Connections

1. Review dimensions in Figure 2 to locate dishwasher's drain, water, and electrical connections.

2. All utilities must be routed in shaded area in the Figure 2. IMPORTANT: Disconnect power before starting installation.

Note: Locate the electrical supply and dishwasher's electrical

junction box on right underside of unit behind kickplate

assembly. See Figure 4. Determine where you will connect

to hot water supply. Review Figure 4 and note the location of

water inlet valve. Determine where you will connect the drain

hose.

3. Cut access holes for the Electrical, Water and Drain hoses in the

shaded areas as shown in Figure 2.

4. The dishwasher operates on a 120 volt, 60 Hz electrical supply.

Provide a separate circuit with a fuse or circuit breaker rated for

at least 15 amps (20 amps if connected with disposer) but not

more than 20 amps.

5. Pull electrical cable through hole into installation area.

6. Be sure water inlet valve is protected from freezing. If valve

freezes and ruptures, flooding may occur.

7. Determine amount of tubing needed to connect hot water supply to the unit's water inlet valve. Extra hose length is necessary.

High-pressure and high-temperature Stainless Flexible hosewith

a minimum inner diameter of V4"may be used. A shut-off valve

installed outside dishwasher cabinet is best.

8. Route water supply line into installation area.

9. Stand dishwasher back upright for further installation.

IMPORTANT: Incoming hot water temperature should be at least 120°F (49°C). Water pressure should be between

20-90 psi.

Property Damage

Do not use the furnished drain hose or a rubber garden hose

for the water supply line. Either of these hoses can burst.

Flooding may occur and cause property damage.

EndStorageLocation

NOTE: Pull the hose from "End Storage Location" side.

See images below to connect the Drain Hose.

L Take drain Hose out of dishwasher and find the end that

doesn't have the black rubber material.

2. Use only the spring clamp that is provided in the accessory kit, place spring clamp over one of the hoses. See Image

Below.

3. Take the plastic side of the drain hose and insert it into the hose that is already attached to the dishwasher make sure

hose ends are flush against each other. See image below.

4, Secure the spring clamp 1/8"from large end of black hose to

the plastic side that was inserted for best sealing results.

See Image Below.

Plastic Ends

of Hoses

Flush

Hose Attached

to Dishwasher

Measure height of cabinet opening from underside ofcountertop to floor. Check chart for height opening and suggested adjustment.

Leg Leveler Adjustment Chart Heightof NumberofTurns to

Cabinet Opening Adjust Levelers

34" (86.4cm) 0

34W' (86.7cm) 2

345he''(87.2cm) 6

34_/2''(87.6cm) 9

2. Move dishwasher to front of installation area.

3. Loosen the rear leveling legs by turning counterclockwise. Refer to chart for number of turns.

Dishwasher Anchoring

4. Install the Cabinet Seal Kit (Instructions included in Kit)

5. Choose one of the methods of attachment below to secure unit,

holes need to be pre-drilled using a #5 drill bit regardless of the option chosen:

a. Side Mount Cabinet Clips (Preferred Method of attachment) b. Top Mount Cabinet Clips (to be used when Side Mount

is not an available option)

CAUTION: Use extreme care in mounting the dishwasher as to not

scratch, bump or otherwise damage the console or tub.

To install the Side Mounting Clips.

Depending on space allowed in cabinet the Side Mounting Clips can be installed with the holes for the screw up (preferred

method) or down as shown in the illustrations below. (Use extreme caution when the clips are in the down position while installing the dishwasher).

NOTE: Install Side Mount Brackets before unit is installed into

the cabinet. Insert screws into the front holes of the

mounting clips only. (See image below)

Use if measures 34V8" to 35"

Use if measures 34" to 34V_"

screw

To install using Top Mount Cabinet Clips:

Depending on the depth of cabinet, the Top Mount

Clip have a break off point that can be removed if

necessary.

NOTE: Install Top Mount Clips before unit is installed into the

cabinet. Screw clips firmly to top brace using screws provided in the literature pack. (See image below)

Electric Shock Hazard

Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury.

Powersupply/water

inletlocation

*DIMENSIONS DO NOT IN CLUED E INSULATION

Water Line Brass Elbow LElectrical Line

(Not Included) (Not Included)

Figure

Tighten Spring Clamp

6. Iflevelersneedtoberemoved,makesurethatthefloorisfreeofall obstructions.

7. Carefullyplacedishwasherinsidecabinetareasuchthatis

centeredinopening.Usecautionwhenmovingdishwasherto preventdamagetocabinet,dishwasherandfloor.

8. Frontofdoorneedstobeevenwiththefrontofadjoiningcabinets. Frontlevelersshouldallow5/16"belowundersideofcountertop

totopofconsole.

9. Checkthatdishwasherislevelfromsidetosideby placingalevel

againstthetopfrontsectionofthetub.SeeFigure5a.

_iiii 1

Figure 5a

10. Check that the dishwasher is level from front to back by taking out the lower rack, place level on the lower rack wheel support at the bottom of the tub. See Figure 5b.

11. Adjust levelers up or down until dishwasher is level.

Holes need to be pre-drilled using a #5 drill to secure unit.

12. Screw mounting brackets firmly to cabinet using screws provided in literature packet. See Image Below.

Figure 5c Figure 5d

13. Open and close dishwasher door slowly. Ensure that there is clearance to the console. Adjust accordingly until door opens

and closes freely.

Property Damage

Do not solder within 6" of the water inlet valve. Damage to

the plastic parts in the valve may occur.

Use care that no sealer, dirt, or other objects enter the valve. Damage to the filter screen may occur.

Be sure the dishwasher is placed where the water inlet valve will be kept from freezing. If the valve freezes, it may

rupture and flooding may occur.

Water Line

1. Flush water line before connecting it to water inlet valve to prevent early clogging of filter screen. Place a bunched towel over end of line to prevent splashing. Open water supply valve for a few seconds and let water drain into a pan. Turn off water

supply at shut-off valve.

2. Route water line to water inlet valve as shown in Figure 4.

3. While firmly pulling water supply line into 90° elbow, tightly

connect water supply to water inlet valve. Supply line must be

free of kinks, scales, chips, and lubricants.

4. Turn on water supply and check for leaks.

Green Wire

to Green Wire

(Ground)

Junction Box

White Wire

Junction' Box Cover

Figure 6a

4. Replacejunction box cover.

Cabinet Seal

Leveling Leg

Water Line

Figure 6b

to Black Wire

(Hot)

Cabinet Attach Clip

Wire

to White Wire

(Neutral)

Cabinet

Electrical Line

check these items:

_t Water and electrical lines are straight out in front of the

dishwasher.

_t All four leg levelers are positioned properly. _l Cabinet Seals are positioned on the sides and top of the

dishwasher.

_l Cabinet Attachment Clips are attached to the cabinet on

both corners on top of the dishwasher.

_l Replace Toe and Kickplate. Note: When replacing Toe

and Kickplate hand tighten screws.

Seal

Electric Shock Hazard

Grounding Instructions: The dishwasher must be connected to a grounded metal,

permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and

connected to the appliance's equipment grounding terminal or lead. It is the consumer's responsibility to contact a

qualified installer to make sure the electrical installation conforms with the National Electrical Code and local codes

and ordinances.

Do not connect the dishwasher to the power supply until the

appliance is permanently grounded. All wiring connections must be enclosed in the junction box.

This unit has copper lead wires. Joining aluminum building wire to stranded copper wire

should be done by a qualified electrician using materials recognized by UL and local codes.

Do not use an extension cord. Such use can result in fire,

electrical shock, or other personal injury.

Failure to follow these instructions could result in death or

serious injury.

1. Review Figures 7, 8 and 9 to see the different ways to connect

dishwasher to drain system. Choose method that best suits yourneed.

Entry Must be

.y.

Branch

Tailpiece

Sink at Left

2" Drain Hose Hole

Figure 7

The drain hose loop must be at least 32" high from the noor

to insure proper drainage.

If you connect to a sink drain, entry will need to be above trap. A "Y" branch tailpiece and connector kit, not included, will make this method easier and includes all needed fittings and

instructions. See Figure 7.

Sink at Right

3. If you connect to a sink trap, local codes may require you to install an air gap kit, (not included). The drain hose will be routed

from dishwasher to air gap inlet as shown in Figure 8. An air gap kit is available from a plumbing supply store. (If the drain

hose is installed through the floor, an air gap is necessary).

4. If you connect to a disposer, the large end of drain hose will fit. Figure 9(a). The knock out plug must be removed from

inside disposer inlet before making the final fit to drain hose. See Figure 9(b).

Cut for 5/8" connection.

Figure 9(a) cut for3/,_ "conn_tion.

Sink at Left

Larger end fts disport

inlet fitting.

Drain Hose

Drain Air Gap

Drain

__[_ Through

Floor into

_ Separate

--L Trap

Sink at Right

Disposer

Figure 9(b)

The drain hoseloop musthe at least 32" highfrom the floor toinsureproper drainage.

If the cabinet wall is wood, sand edges of hole until smooth and

rounded. If cabinet wall is metal, cover all sharp edges with electrical or duct tape to avoid cutting drain hose.

6. Move unit back in place while routing drain hose through access

hole. Use caution to prevent damage to the dishwasher, floor and

cabinets. IMPORTANT: Make sure there are no sharp bends

or kinks that might restrict drain flow.

7. Secure drain hose to sink drain, disposer, or separate trap with a

clamp. IMPORTANT: Be careful not to overtighten clamp or you may damage end of hose. Do not connect hose to

horizontal pipe between sink drain and disposer.

8. Be sure unit does not rest on drain hose. ttshould be free of

electrical components and door springs. Do not cut corrugated drain hose. Pull excess through cabinet and place under sink.

Make sure hose does not come in contact with any sharp edges.

2" Drain Hose Hole

Electric Shock Hazard

Disconnect electrical power at the fuse box or circuit breaker box before beginning

installation. Failure to follow this warning could result in

death or serious injury.

Cut Hazard

Metal color panels are sharp and should be handled with care. Wear gloves to protect

hands. Failure to follow this warning may result in

injury.

Electric Shock Hazard

If all connections are correct, there are no leaks, and unit runs properly, replace the kickplate assembly before placing unit into operation.

Failure to follow this warning could result in

electric shock.

check these #ems:

_t Water and drain lines have no kinks and move freely

behind the dishwasher.

_t Water supply is turned on. _l Joints are free of leaks.

_t Wiring connections to junction box are tight all access

panels are secured back in place.

_t Replace kickplate. See Figure 1 _l Drain hose is assembled to Drain Hose Connector.

_t All packing materials and consumer literature have

been removed from inside unit.

_t Dishwasher is level and securely fastened.

_t Open and close door to make sure it does not hit

surrounding cabinet or countertop.

_l Make sure that all wire ties are removed from the Adjustable

Rack Assembly, Versa Tray, Utility Tray and Silverware

Baskets.

Operate the machine through at least one fill and pump-out, checking the following items:

_t On EWDW6505 press and hold SET Icon for 5 seconds

before first use. On EIDW6305 and EIDW6105 press and

hold down HI-TEMP Icon for 5 seconds before first use.

_l At first fill, approximately 2 minutes make sure water

completely covers filter surface.

_l At pump-out: (pump-out is either when the cycle is

completed or canceled, refer to the Use and Care Manual

for Start/Cancel), make sure all water is pumped out.

_l Check water connections again for leaks.

Electrical Supply

1. Remove junction boxcoverand pull housewiring into junction box. See Figures Below.

2. Use a UL listed conduit connector (not included) at box to stabilize wiring.

3. Connect incoming black lead to dishwasher's black lead, incoming white lead to dishwasher's white lead and incoming green lead to dishwasher's green lead with wire nuts. (See Grounding Instruction Warning). Wire nuts must be tight.