Warranty Information ....................................... 55
4
Safety
IMPORTANT SAFETY INSTRUCTIONS
• All ranges can tip.
• Injury to persons could result.
• Install anti-tip device packed with range.
• See Installation instructions.
To reduce the risk of tipping of the range, the range must be secured by properly installed antitip bracket(s) provided with the range. To check if the bracket (s) is installed properly, remove the
lower panel or storage drawer and verify that the anti-tip bracket (s) is engaged. Refer to the
installation instructions for proper anti-tip bracket(s).
•Remove all tape and packaging wrap before using the appliance. Destroy the carton
and plastic bags after unpacking the appliance. Never allow children to play with
packaging material.
•Proper Installation—Be sure your appliance is properly installed and grounded by
a qualified technician in accordance in the United States with National Electrical
Code ANSI/NFPA No. 70—latest edition and local code requirements, and in Canada
with CSA C22.1 PART 1—latest edition and local code requirements. Install only per
installation instructions provided in the literature package for this appliance.
Ask your dealer to recommend a qualified technician and an authorized repair service. Know
how to disconnect the electrical power to the range at the circuit breaker or fuse box in case
of an emergency.
•User Servicing—Do not repair or replace any part of the appliance unless specifically
recommended in the manuals. All other servicing should be done only by a qualified
technician to reduce the risk of personal injury and damage to the appliance.
•Never modify or alter the construction of a range by removing leveling legs, panels,
wire covers, anti-tip brackets/screws, or any other part of the product.
Stepping, leaning or sitting on the door or drawer of this appliance
can result in serious injuries and may also cause damage to the appliance. Do not
allow children to climb or play around the appliance. The weight of a child on an open door
may cause the appliance to tip, resulting in serious burns or other injury. An open drawer,
when hot, may cause burns.
Do not use the oven or warmer drawer (if equipped) for storage.
•Storage in or on Appliance—Flammable materials should not be stored in an oven,
near surface units or in the drawer (if equipped). This includes paper, plastic and cloth
items, such as cookbooks, plasticware and towels, as well as flammable liquids. Do not store
explosives, such as aerosol cans, on or near the appliance. Flammable materials may
explode and result in fire or property damage.
Do not store items of interest to children in the cabinets above the
appliance. Children climbing on the range to reach items could be seriously injured.
•Do not leave children alone. Children should not be left alone or unattended in the
area where an appliance is in use. They should never be allowed to sit or stand on any
part of the appliance.
Safety
•DO NOT TOUCH SURFACE UNITS, AREAS NEAR THESE UNITS, OVEN HEATING
ELEMENTS OR INTERIOR SURFACES OF THE OVEN OR WARMER DRAWER (if
equipped). Both surface units and oven heating elements may be hot even though they are
dark in color. Areas near surface units may become hot enough to cause burns. During and
after use, do not touch, or let clothing or other flammable materials touch these areas until they
have had sufficient time to cool. Among these areas are the cooktop, surfaces facing the
cooktop, the oven vent openings and surfaces near these openings, oven door and window.
•Wear Proper Apparel—Loose-fitting or hanging garments should never be worn
while using the appliance. Do not let clothing or other flammable materials contact hot
surfaces.
Never use your appliance for warming or heating the room.
•Do Not Use Water or Flour on Grease Fires—Smother the fire with a pan lid, or use
baking soda, a dry chemical or foam-type extinguisher.
•When heating fat or grease, watch it closely. Fat or grease may catch fire if allowed to
become too hot.
5
•Use Only Dry Potholders—Moist or damp potholders on hot surfaces may result in
burns from steam. Do not let the potholders touch hot heating surface units or interior oven
elements. Do not use a towel or other bulky cloth instead of a potholder.
•Do Not Heat Unopened Food Containers—Build up of pressure may cause the
container to burst and result in injury.
•Remove the oven door from any unused appliance if it is to be stored or discarded.
•IMPORTANT—Do not attempt to operate the oven during a power failure. If the power
fails, always turn the oven off. If the oven is not turned off and the power resumes, the oven
may begin to operate again. Food left unattended could catch fire or spoil.
Electronic controllers can be damaged by cold temperatures. When you
use your appliance for the first time, or if it has not been used for a long period of time,
make sure that it has been exposed to a temperature above 0°C/32°F for at least 3 hours
before connecting it to the power supply.
IMPORTANT INSTRUCTIONS FOR USING YOUR COOKTOP
•Know which knob controls each surface heating unit.
•Use Proper Pan Size—This appliance is equipped with one or more surface units of different
sizes. Select utensils having flat bottoms large enough to cover the surface unit. The use of
undersized utensils will expose a portion of the surface heating unit to direct contact and may
result in ignition of clothing. Proper relationship of utensil to the surface unit will also improve
efficiency.
•Utensil Handles Should Be Turned Inward and Should Not Extend Over Adjacent
Surface Units—To reduce the risk of burns, ignition of flammable materials, and spillage due
to unintentional contact with the utensil. The handle of the utensil should be positioned so that
it is turned inward, and does not extend over adjacent surface unit.
6
Safety
•Never Leave Surface Units Unattended—Boilovers cause smoking and greasy spillovers
that may ignite, or a pan that has boiled dry may melt.
•Protective liners— Do not use aluminum foil to line oven bottom or any other part of the
appliance. Only use aluminum foil as recommended for baking if used as a cover placed on
the food. Any other used of protective liners or aluminum foil may result in a risk of electric
shock or fire or a short circuit.
•Glazed Cooking Utensils—Only certain types of glass, glass/ceramic, ceramic, earthenware,
or other glazed utensils are suitable for cooktop service without breaking due to the sudden
change in temperature. Check the manufacturer's recommendations for cooktop use.
•Do Not Use Decorative Surface Element Covers. If an element is accidentally turned on,
the decorative cover will become hot and possibly melt. Burns will occur if the hot covers are
touched. Damage may also be done to the cooktop.
FOR GLASS COOKTOPS ONLY
•Do Not Clean or Operate a Broken Cooktop —If cooktop should break, cleaning solutions
and spillovers may penetrate the broken cooktop and create a risk of electric shock. Contact
a qualified technician immediately.
•Clean Cooktop Glass with Caution—If a wet sponge or cloth is used to wipe spills on a hot
cooking area, be careful to avoid a steam burn. Some cleaners can produce harmful fumes
if applied to a hot surface.
•Avoid scratching the cooktop glass with sharp objects.
IMPORTANT INSTRUCTIONS FOR USING YOUR OVEN
•Use Care When Opening Door or Drawer—Stand to the side of the appliance when opening
the door of a hot oven. Let hot air or steam escape before you remove or replace food in the
oven/warmer drawer.
•Keep Oven Vent Ducts Unobstructed. The oven is vented at the front above the oven door
(ceramic glass cooktop models) or through the right rear element (coil element models).
Touching the surfaces in this area when the oven is operating may cause severe burns. Also,
do not place plastic or heat-sensitive items on or near the oven vent. These items could melt
or ignite.
•Placement of Oven/Warmer Drawer (if equipped) Racks. Always place oven racks in
desired location while oven/drawer (if equipped) is cool. Remove all utensils from the rack before
removing rack. If rack must be moved while oven is hot, use extreme caution. Use potholders
and grasp the rack with both hands to reposition. Do not let potholders contact the hot oven
element or interior of the oven/warmer drawer (if equipped).
•Do not use a broiler pan without its insert. The broiler pan and grid allow dripping fat to drain
and be kept away from the high heat of the broiler.
•Do not cover your broiler or warmer drawer (if equipped) grid with aluminum foil.
Exposed fat and grease could ignite.
Safety
•Do not touch a hot light bulb with a damp cloth. Doing so could cause the bulb to break.
Disconnect the appliance or turn off the power to the appliance before removing and replacing
light bulb.
IMPORTANT INSTRUCTIONS FOR CLEANING YOUR RANGE
•Clean the range regularly to keep all parts free of grease that could catch fire. Exhaust
fan ventilation hoods and grease filters should be kept clean. Do not allow grease to
accumulate. Greasy deposits in the fan could catch fire. Refer to the hood manufacturer's
instructions for cleaning.
•Cleaners/aerosols—Always follow the manufacturer's recommended directions for use. Be
aware that excess residue from cleaners and aerosols may ignite causing damage and/or
injury.
SELF-CLEANING OVENS:
• Clean in the self-cleaning cycle only the parts of the oven listed in this owner's guide.
Before self-cleaning the oven, remove all utensils stored in the oven.
• Do not clean the oven door gasket. The door gasket is essential for a good seal. Care should
be taken not to rub, damage or move the gasket.
7
• Oven racks. Oven racks will be damaged if left in the oven during a self-cleaning cycle.
• Do not use oven cleaners. No oven cleaner or oven liner protective coating of any kind should
be used in or around any part of the oven.
• Remove oven racks. Oven racks will be damaged if left in the oven during a self-cleaning cycle.
The health of some birds is extremely sensitive to the fumes given off
during the self-clean cycle of any range. Move birds to another well ventilated room.
IMPORIMPOR
IMPOR
IMPORIMPOR
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of
California to publish a list of substances known to the state to cause cancer, birth
defects or other reproductive harm, and requires businesses to warn customers of
potential exposure to such substances.
NONO
TETE
NO
TE
NONO
TETE
Save these important safety instructions for future reference.
TT
ANT SAFETY NOANT SAFETY NO
T
ANT SAFETY NO
TT
ANT SAFETY NOANT SAFETY NO
TICETICE
TICE
TICETICE
8
Feature Overview
YOUR SLIDE-IN RANGE
CERAMIC GLASS
COOKTOP
TOUCH ACTIVATED
GLASS CONTROL
PANEL
LARGE METAL
HANDLE
CURVED GLASS
OVEN DOOR
LOWER OVEN
DOOR WINDOW
GLASS
SINGLE ELEMENT
6” 1200W
TRIPLE ELEMENT
6” 1000W
9” 2000W
12” 2700W
SINGLE ELEMENT
6” 1200W
DOUBLE ELEMENT
5” 750W
7” 1800W
DOUBLE ELEMENT
6” 1600W
9” 3000W
UPPER
OVEN
LOWER
OVEN
YOUR SLIDE-IN RANGE
Feature Overview
9
OVEN DOOR LATCH
OVEN VENT
BROILING ELEMENT
OVEN RACK SUPPORT
SLIDEABLE OVEN RACKS
CONVECTION FAN
OVEN LIGHT
OVEN RACK SUPPORT BRACKETS
LOWER OVEN RACK
BROILER PAN
BROILER PAN GRID
CONVECTION
ROASTING RACK
10
Feature Overview
OVEN RACK SUPPORTS & OVEN VENTS
Installing Oven Rack Supports
ALWAYS INSTALL OVEN RACK SUPPORT
BEFORE TURNING ON THE OVEN (WHEN
THE OVEN IS COOL).
To install oven rack support, insert the
supports by pushing them downward into the
two brackets on each side of the oven interior,
as shown below.
To remove the oven rack support for a selfclean cycle, pull up the support to disengage
them from the brackets. If the rack supports
are not removed, the self-clean cycle won’t
start.
Oven Rack Positions
This oven is equipped with ladder rack supports with 7
positions to accomodate precisely every mode of cooking.
Rack positions
7
6
5
4
3
2
(NON-SLIDING
1
RACK ONLY)
Oven Vents Location
The oven is vented above each door. When
the oven is on, warm air is released through the
vents. This venting is necessary for proper air
circulation in the oven and good baking results.
Oven Vent
Warm Air
Feature Overview
REMOVING AND REPLACING OVEN RACKS
Removing Sliding Oven Racks
1. With the rack in its closed position; grasp the rack and the sliders at once.
2. Slightly lift the rack and sliders and pull it to clear the first bracket.
3. Pull the rack and sliders until the second bracket stops the rack.
4. Lift the rack and sliders and carefully remove them from the oven.
Refer to the care and cleaning section for directions on how to clean the racks.
Replacing Sliding Oven Racks
To replace the oven racks, follow the intructions above in reverse order.
11
1st Bracket
TOWARD FRONT OF OVEN
2nd Bracket
Oven Rack
Oven Rack Slider
Oven Rack Support
Removing Non-Sliding Oven Rack
Simply pull the rack and slightly tilt it upward when the rack hits its stop position.
Replacing Non-Sliding Oven Rack
Insert the rack into the oven rack supports by inserting the rack openings into the rack
supports. Be sure the rack is at the same position on each oven rack support on both sides.
TOWARD BACK OF OVEN
Always arrange the oven racks when the oven is cool (prior to operating the oven). Always use
oven mitts when using the oven.
Insert the openings
into the rack support
12
Feature Overview
OVEN CONTROL PAD FUNCTIONS
1
10
Light Pad- Used to turn the oven light on and off.
1
Bake Pad- Used to enter the normal baking mode temperature.
2
Broil Pad- Used to select the variable broil mode.
3
Convection Bake Pad- Used to select the convection baking mode.
4
Convection Roast Pad- Used to select the convection roasting mode.
5
23568947
11121314151617
Convection Broil Pad- Used to select the convection broil mode.
6
Keep Warm Pad- Used to select the keep warm mode.
7
Slow Cook Pad- Used to select the slow cook mode.
8
Perfect Turkey Pad- Used to select the perfect turkey cooking mode.
9
Control Lock Pad- Used to disable all oven function.
10
Multi Stage Pad- Used to enter up to three subsequent modes.
11
Cook Options Pad- Used to light up the cooking options pads.
12
Cook Time Pad- Used to set a cooking duration time.
13
End Time Pad- Used to select the time at which the cooking will end.
14
Probe Pad- Used to activate the meat probe mode.
15
Rapid Preheat Pad- Used to preheat the oven to the desired temperature.
16
Conv. Convert Pad- Used to convert a standard temperature to a convection
17
temperature.
Feature Overview
OVEN CONTROL PAD FUNCTIONS (CONTINUED)
13
1819
2021
28
22232425
29
26
27
Defrost Pad- Used to select the defrost mode.
18
Dehydrate Pad- Used to select the dehydrate mode.
19
Bread Proof Pad- Used to select the bread proof mode.
20
Clean Pad- Used to select the self-cleaning mode.
21
My Favorite 1 Pad- Used to save or recall the favorite 1 cooking mode.
22
My Favorite 2 Pad- Used to save or recall the favorite 2 cooking mode.
23
My Favorite 3 Pad- Used to save or recall the favorite 3 cooking mode.
24
Lite Pad- Used to start a 2 hours self-clean cycle.
25
Med Pad- Used to start a 3 hours self-clean cycle.
26
Heavy Pad- Used to start a 4 hours self-clean cycle.
27
Upper Oven Pad- Used to activate the upper oven for cooking operation.
28
Lower Oven Pad- Used to activate the lower oven for cooking operation.
29
User Preference Pad- Used to bring the user preference menu in the display.
30
Cancel Pad- Used to cancel any function previously entered except the time of day
31
and minute timer. Push Cancel pad to stop cooking.
30
31
32
34
32
33
3536
Timer Pads- Used to set or cancel the minute timer. The minute timer does not start
32
or stop cooking.
Start Pad- Used to start all oven functions.
33
0 Thru 9 Number Pads- Used to enter temperature and times.
34
- lo Pad- Used to lower the temperature and times.
35
+ hi Pad- Used to raise the temperature and times.
36
14
Feature Overview
COOKTOP CONTROL PAD FUNCTIONS
38
39
40
41
42
ON / OFF Pad- Used to toggle ON and OFF the associated surface element.
38
HI + Pad- Used to select the highest element temperature or raise the temperature
39
currently displayed.
40
MED Pad- Used to select the medium element temperature.
LO - - Used to select the lower element temperature or lower the temperature
41
currently displayed.
Burner Size Pad- Used to toggle between the available surface element burner
42
sizes.
Getting Started
SETTING CLOCK AT POWER UP
When the unit is first plugged in, or when the power supply to the range has been interrupted,
the timer in the display will flash with "12:00". The clock cannot be set when the oven is on. If
an invalid time of day is entered, the control will triple beep to prompt you to re-enter a valid time
of day.
To set the clock (example for 1:30):
-
1.Press
to raise or lower the actual time displayed.
2.Press START to accept the changes or CANCEL to start with a time of 12:00.
1
pads to set the time of day to 1:30. The pads
3
0
CONTROL PANEL DISPLAY MODES
Sleep Mode:
Your control will remain in a sleep mode when not in use. Only the clock will display during this
mode. You will need to wake the control to begin any function.
+
or
can also be pressed
lo
hi
15
Wake Mode:
To wake the control, touch within the display panel. After 2 minutes without activity the control
will beep and go back into sleep mode.
To start a cooking feature you must select either the upper oven or the lower oven. User
preferences will be available during this mode as well as timers, oven light and the control lock.
TEMPERATURE VISUAL DISPLAY
Your oven is equipped with a temperature visual display for each oven. When a cooking mode
is set, the actual temperature will be shown in the display and will rise as the unit preheat. When
the unit has reached its target temperature, a chime will sound to remind you to place the food
in the oven. This feature will be active with some cooking modes; bake, convection bake,
convection roast and perfect turkey. The cooking modes which does not feature the temperature
visual display will be noted in their descriptions.
NOTE: The lowest temperature that can be displayed is 100°F.
16
Getting Started
OVEN LIGHT
Your appliance includes “theater” style oven lighting feature that gradually lights both the upper
and lower oven interiors to full brightness. The upper oven is equipped with 2 halogen lights and
the lower oven is equipped with 1 incandescent light. The oven lights will turn on automatically
when the oven door is opened. The oven light may be turned on when the door is closed by using
the oven light pad located on the control panel. The oven light key will toggle the lights in both
ovens at the same time at full intensity.
To toggle the Oven Lights ON and OFF:
1.Press OVEN LIGHT .
CONTROL LOCK
The Control Lock feature automatically locks the upper oven door, control panel and the cooktop.
The Control Lock is only allowed when the oven and the cooktop are turned OFF (not active).
DOOR LOCK will flash in the display for 20 seconds or until the door has finished locking. Once
the door has been locked, Loc message will appear in the upper display and “- -” will appear in
the cooktop displays. Do not attempt to open the oven door while DOOR LOCK is flashing.
To toggle the Control Lock ON and OFF:
1.Keep CONTROL LOCK pressed for 3 seconds.
SETTING THE KITCHEN TIMER
This unit is equipped with 2 Kitchen Timers which serves as extra timers in the kitchen that will
beep when the set time has run out. It does not start or stop cooking. The Timer feature can be
used during any of the other oven control functions and cooking modes.
To set the Timer (example for 5 minutes):
1.Press TIMER . "00:00" will appear in the display.
-
2.Press 5 pad to set the timer to 5 minutes. The pads
or lower the actual time displayed.
3.Press again TIMER to accept and start the countdown.
4.When the set time has run out, "00:00" will be displayed and the TIMER pad will flash.
The clock will sound a chime that will be repeated at regular intervals until the TIMER
pad is pressed.
+
or
can also be pressed to raise
lo
hi
To cancel the Timer before the set time has run out:
Press TIMER . The display will return to the time of day.
Setting Surface Controls
ABOUT THE CERAMIC GLASS COOKTOP
The ceramic cooktop has radiant surface elements located below the surface of the glass. The
design of the ceramic cooktop outlines the area of the surface element underneath. Make sure
the diameter of the pan matches the diameter of the element outline on the cooktop. Heat is
transferred up through the surface of the cooktop to the cookware. Only flat-bottom cookware
should be used. The type and size of cookware, the number of surface elements in use and the
settings, are all factors that will affect the amount of heat that will spread to areas beyond the
surface elements. The areas surrounding the elements may become hot enough to cause
burns.
ABOUT THE RADIANT SURFACE ELEMENTS
The element temperature rises gradually and evenly. As the temperature rises, the element will
glow red. To maintain the selected setting, the element will cycle on and off. The heating element
retains enough heat to provide a uniform and consistent heat during the off cycle. For efficient
cooking, turn off the element several minutes before cooking is complete. This will allow residual
heat to complete the cooking process.
Your range is equipped with radiant surface burners with different wattage ratings. The ability to
heat food quicker and in larger volumes increases as the element wattage increases.
17
NONO
TETE
NO
TE
NONO
TETE
Radiant elements have a limiter that allows the element to cycle ON and OFF, even at the HI setting. This helps to
prevent damage to the ceramic glass cooktop. Cycling at the HI setting is normal and can also occur if the cookware
is too small for the radiant element or if the cookware bottom is not flat (Refer to page 18 for using correct cookware
instructions with the cooktop).
Please read detailed instructions for ceramic glass cooktop cleaning in the General Care & Cleaning section and
Solutions to Common Problems section of this Use and Care Guide.
Loading...
+ 39 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.