USER MANUAL
EFT60001
EFT60002
EFT60003
EN
GENERAL INFORMATION SAFETY WARNINGS 5
CHARACTERISTICS
INSTALLATION
USE
MAINTENANCE
6
7
8
9
electrolux 3
4 electrolux
EN
Welcome to the world of Electrolux
Thank you for choosing a rst class
product from Electrolux, which hopefully will provide you with lots of pleasure
in the future. The Electrolux ambition is
to offer a wide variety of quality products that make your life more comfort-
able. You nd some examples on the
cover in this manual. Please take a few
minutes to study this manual so that
you can take advantage of the benets
of your new machine. We promise that
it will provide a superior User Experience delivering Ease-of-Mind.
Good luck!
General Information-Safety Warnings electrolux 5
GENERAL INFORMATION SAFETY WARNINGS
GENERAL INFORMATION
This canopy hood is designed to be xed
to any rigid vertical surface, over a gas or
electric hotplate and can be used either in
the extraction mode (ducted to the outside) or in the recircu-lation mode (internal
recycling). All cookers hood perform better
when used in evacuation mode. During
winter time it may be convenient to use the
hood in the recycling mode to avoid heat
loss from the kitchen.
Before starting the installation, consi
deration should be given to the difculties to be found during installation. The
installation work must be undertaken
by a qualied and competent person in
conformity to the rules concerning the
evacuation of contaminated air.
The manufacturer disclaims all liability
for any damage or injury caused as a re
sult of not following the instructions for
installation contained in the following
text.
1 - SAFETY WARNINGS
1.1- When used in the extraction mode,
the cooker hood ducting must not
be connected to a ue which is
used for exhausting fumes from
appliances supplied with energy
other than electric, such as a cen
tral heating ue or water heating
ue.
1.2- Before connecting to the mains
supply ensure that the mains
voltage corresponds with the voltage on the rating plate inside the
hood.
1.3- Connect the cooker hood to the
mains via a bipolar switch which
has 3mm clearance between the
contacts.
1.4- For cooker hoods featuring an
earth cable, make sure the electric
plant of your house is correctly
earthed.
1.5- Appliance in class II are provided
with a double insulation; there
fore do not connect then through
earthed plugs but through simple
bipolar plugs.
1.6- When installed, the hood must be
positioned at least 65cm above the
hotplate.
1.7- Never do ambé cooking under
-
-
-
this cooker hood.
1.8- Never leave frying pans unat
tended during use as overheated
fat and oil may catch re.
1.9- Before carrying out any kind of
maintenance or cleaning, discon
nect the hood from the mains supply.
1.10-If the room where the cooker hood
is to be used contains a fuel burn
ing appliance such as a central
heating boiler then this must be of
the room sealed or balanced ue
type. If other types of ue or appliance are tted, ensure that there
is an adequate supply of air into
the room. When the cooker hood
is used in conjunction with appliances supplied with energy other
than electric, the negative pres-
sure in the room must not exceed
0,04 mbar to prevent fumes being
drawn back into the room by the
cooker hood.
1.11-The appliance must be positioned
so that the plug is accessible.
1.12-If the supply cord is damaged,
it must be replaced by a special
cord or assembly available from
the manufacturer or its service
agent.
-
EN
-
-
-
6 electrolux Characteristics
CHARACTERISTICS
Dimensions
EN
Installation electrolux 7
INSTALLATION
2 - INSTALLATION INSTRUCTIONS
Some installation systems require the
opening and removal of the metal grille
panel.
2.1 - Instructions for opening and
removing the metal grille panel
To open the grille panel, press inwardly
on the two slider catches at each side
of the grille panel and the grille will pivot
down.
To remove the metal grille, pull forward
on the right hand side so that the hinge pin on the back of the grille will be
released from the slot in the side of the
casing.
2.2 - Wall cabinet xing
a-Predrilled wall cabinet: x the hood
onto the wall cabinet base panel using
the four screws 4.2 x 45 mm (supplied
with the xing kit).
It is not necessary to open the metal
grille.
b-No predrilled wall cabinet:
b.1-If the hood is provided with a pa-
per xing template, follow the instruc-
tions.
b.2-If the hood is not provided with
a paper xing template, position the
hood on the wall cabinet base panel
and pilot drill the 3.5 x 16 mm screws
(not supplied with the xing kit) from
the inside onto the wood.
2.3 - Wall mounting
a-Drill two Ø 8 mm holes on the wall us-
ing the paper template, insert two rawl
plugs and two 4.2 x 44,4mm screws
leaving 5 mm untightened. Open the
metal grille panel, hook the hood on
and fully tighten the screws.
b-If the hood is not provided with a pa-
per xing template, drill two Ø 8mm
holes (see draw.), insert the plugs and
screws, proceeding as directed under
paragraph a.
c-For wall mounting using wallbrackets
(optional), follow the instructions of
the xing template.
d-Pay attention to the safety regulation
of point 1.6.
2.4 - Choice of operating mode
a - Evacuation mode
To check that the hood is set up for
evacuation, open the grille panel and
make sure that the conversion lever or
the change-over knob on the centrifugal
unit is in the DUCTING position. The
charcoal lter is not required.
For ducting to the outside, the hood is
supplied with a rear and top outlet. A
ange spigot of 100 mm diameter (120
mm in certain models) is usually tted
on the top outlet and a blanking plug on
the rear outlet. If you choose to duct the
hood from the rear of the casing, you
should invert the position of the ange
and of the blanking plug. Pay attention
to the safety regulation 1.1.
b - Internal recirculation mode
To check that the hood is set up for
recycling, open the grille panel and
make sure that the conversion lever or
the change-over knob on the centrifugal
unit is in the RECYCLING position. The
charcoal lter is to be tted. To t the
charcoal lter, support the lter with one
hand and turn the thumb screw through
the centre of the charcoal lter. If the
lter is of the interlocking type, turn the
lter clockwise. The hood can remain
connected to the outside.
2.5 - Electrical connection and
working test
1-The safety measures 1.2, 1.3, 1.4 and
1.5 of paragraph 1 are to be strictly
observed.
2-Once the electrical connection has
been completed, check that the
worktop illumination, motor and
speeds work properly.
EN
8 electrolux Use
USE
3 - OPERATION
3.1- Controls are located on the right
EN
hand side of the front to operate
worktop illumination and select the
most suitable working speed for
your cooking. To increase the area
of extraction, the glass visor should
be pulled open. The top speed
should be used when frying or
cooking foods with strong odours,
while a lower speed can be used
for normal cooking. To obtain the
best performance from your hood,
turn it on before you start cooking
and leave it running for a few minutes after your cooking is over to
clear the air.
3.2- Pay attention to safety regulations
1.7 and 1.8
MAINTENANCE
4 - MAINTENANCE AND CLEANING
Regular maintenance and cleaning will
ensure good performance and reliability, while extending the working-life of
the hood. Special attention should be
reserved to the grease lter and to the
charcoal lter (recycling mode).
4.1 - Grease lter
This retains the solid grease particles
and can be supplied in different types.
lt is tted onto the reverse side of the
metal grille panel. Maintenance of the
grease lter varies according to the
used type.
a-Whatever type of lters used, the lter
is easily removed from the grille by
pushing the metal wire clips to one
side and removing.
b-Thin synthetic lter (1 mm thick). It
should not be washed and should be
replaced every two months. If the lter
is provided with a saturation indicator,
replace when:
b.1-The violet colour of the dots, which
are visible through the metal grille, is
spread over the whole surface of the
lter.
b.2-The red colour of the stripes, which
is not visible through the metal grille
when the lter is clean, becomes
visible from the outside of the metal
grille.
c-Multi-layer metal lter. It should be
washed once a month in hot water
using mild detergent or liquid soap.
It can be washed in a dish-washer. It
should not be bent and should be left
to drain dry.
WARNING: An excess of grease in the
lter not only would affect the performance of the hood, but it is also a pos-
sible re risk. We strongly recommend
therefore to clean and replace lters
in accordance with the manufacturer
instructions.
Maintenance electrolux 9
4.2 - Cleaning Metal self-
supporting Grease Filters
• The lters are washable and must be
cleaned at least every 2 months of
operation, or more
frequently for particularly heavy usage.
• Remove the lters one at a time by
pushing them towards the back of the
group and pulling down at the same
time.
• Wash the lters, taking care not to
bend them. Allow them to dry before
retting.
• When retting the lters, make sure
that the handle is visible on the out-
side.
4.3 - Charcoal lter
The charcoal lter is a chemical lter to
be used only when the hood is in the
recycling position. To replace the char-
coal lter, open the grille and remove the
thumb screw through the centre of the
charcoal lter. If the lter is of the interlocking type, turn the lter anticlockwise.
Replace by reversing the operation.
For a good performance replace the
charcoal lter on average every three
months.
4.4 - Worktop illumination
If a lamp fails to function at any time,
open the metal grille panel and check
that the lamp is fully screwed into the
holder. When changing the lamp, an
identical replacement must be tted to
ensure a safe working of the hood.
4.5 - Cleaning
The metal work should be cleaned
regularly, at least once a month, using
mild household cleaner and
polish. Never use abrasives. For all operations from point 4.1 to point 4.4 and in
particular for point 4.3,
pay special attention to the safety regulation 1.9.
EN
www.electrolux.com
436003730_02 - 070530
Loading...