Electrolux E24ID74QPS0A, EW24ID70QT0A, EW24ID80QS0A, FGID2474QB4B, FGID2474QF4B Installation Guide

...
Dishwasher
CD.808 936 635
Installation Instructions
INSTALLER: Leave Installation Instructions with owner• OWNER: Read your dishwasher Use and Care Manual. It contains
important safety information for operating this appliance• It also has many suggestions for getting the best results from your dishwasher•
NOTE: Put unit on its back being careful not to pinch the Water Drain Hose.
1. Remove two (2) screws at the top the kickplate assembly
2. Tilt and pull forward the kickplate to remove it. - see Figure 1. NOTE:It is not necessary to remove the outer door for installation•
Figure I
Figure 3
Front Closed
_23¾"(60,3 cm)-_ _24¼"(61,5 cm)_
33¾"
(86cm),
Adjustable
to
35¾"
e e
90,8jm)**
50¼"(127,6 cm}
/
/
cm)
Opendoor
to900
Open Door
Figure 5
_- 22½"(57,1
NOTE: Install cabinet seal to dishwasher before placing it into
the cabinet
®
Read all instructions before installing dishwasher. For your safety, please read and observe all safety
instructions. This guide will help you anticipate drain, water, and
electrical connections, and help you select the best location for the dishwasher•
The dishwasher is provided with water heating feature. The dishwasher is intended for connection to hot water supply.
Tip Over Hazard
Do not use dishwasher until completely installed. Do not push down on open door.
Failure to follow this warning can result in serious injury.
Cut Hazard
To prevent serious injury from sharp edges, wear work gloves when handling, unpacking or disassembling unit.
®
®
Height0nlyadjustableto 35¾" (90,8cm)maxwhen *DIMENSIONSDONOTINCLUDEINSULATION-
installedin35¾" (90,8cm)maxstandardcabinetrycutout. INSULATIONBLACKETMAYBECOMPRESSED
to 353A'' UPONINSTALLATION.
IMPORTANT: For proper operation and appearance of unit, cabinet opening should have dimensions as shown in Figure 2. If unit is to be placed in a corner, there must be at least a 2-inch
side clearance between the wall and the open door.
2. Floorshouldbe flat andfreeof any obstruction.
IMPORTANT: Drain, water, and electrical lines should be roughed-in before going any further.
Electric Shock Hazard
Electrical, water, and drain lines must be confined
to shaded areas in Figure 2.
Electric conductors, water, and drain could be
damaged.
Failure to follow these instructions could result in
fire or electric shock.
NOTE: If dishwasher is installed at end of a cabinet, sides and back must be fully enclosed.
Figure 4
Powersupply/water inlet location
Figure 6
Parts Included:
Tools and Materials Needed for
Installation (Not Included)
Drill, Electric
Driver, Socket 5/32% 1/4", 5/16"
Flaring Tool / Tube Cutter (for copper tubing)
Flashlight
Level
Pipe Joint Compound (for iron pipe plumbing) or Pipe Thread Tape (for sealing threads)
Pliers
Safety Glasses
Saw, Keyhole or 1/2", 11/2"to 2" Hole Cutters
Screw Drivers, Slotted and Q2 Phillips (magnetic tip preferred)
Work gloves
Tape, Electrical or Duct
Measuring Tape
Wire Stripper or Utility Knife
Wrench, Hex-end
Wrenches, 2 Adjustable (for copper tubing) or 2 Pipe wrenches (for iron pipe plumbing)
Parts You Will Need*(NotIncluded)
Drain HoseClamp, 11/4" (3,1 cm)Diameter
Brass Elbow, 90° with a 3/4" ( Q 2 cm )-11.5 NH to 3/8" ( Q 2 cm )
NPT Compression fitting
Conduit Connector (UL Listed)
Wire Nuts, three (3) for 12-14 gauge wire (UL Listed)
"klf required:
"Y" Branch Tailpiece and
Connector Kit (See Step 8 )
Air Gap Kit (See Step 8 )
All the parts can be found at local hardware, electrical and plumbing supply stores•
Electric Shock Hazard
Disconnect electrical power at the fuse box or circuit breaker box before beginning installation.
Failure to follow this warning could result in death or serious injury.
3. Locate water inlet valve behind kickplate on bottom left underside of unit. See Figure 4 The valve has a 3/8" ( 1 cm ) NPT male fitting•
4. Connect the 90 ° elbow (not included) to water inlet valve. When tightened, point elbow should point toward the left. To prevent bending of bracket or breaking of valve, avoid overtightening. See Figure 4.
Cabinet Preparation:
As a precaution, it is recommended, but not required that the
cabinets enclosing all sides of the dishwasher (including the underside of the countertop) be sealed with an oil based paint or moisture-proof polyurethane to prevent possible steam/moisture damage.
Electric Shock Hazard
Observe all local codes and ordinances for electrical and plumbing connections. All electrical
and plumbing work should be performed by qualified persons. Failure to follow this warning
could result in death or serious injury.
Figure 2
1• Make sure your location has the correct drain, water, and
electrical outlets to make the connections• Do not install unit
under a cooktop range, Damage to tub or other components will
occur.
Electrical, water, -_"
34"(86,36cm) min.to35¾"
(90,8cm)
max.**
/.,,_/
3½" (8,89 cm) min.to _/' ¼" (3,1 cm) required from unit to \
4½"(11,430m)m_x. _/// _ 2¼" underside ofcountertop.) 2¼"<
/ J(5,7 cm) (5,7 cm)'
/
_4_ 24" (61cm) ....................................................................................................................................................................................................................
and drain lines
must be confined
to shaded area.
Preferred
Drain Areas
3" "(45,7 cm)
cm) max. height
standardcabinetrycutout.
(5/16"[0,8cm]mfn. \.,_4_\ Ix
clearance 1",
90° I
3" (7,6cm)
.X
Water line Brass Elbow
(Not Included) (Not Included) Electrical Line
Locating the Connections
1. Review dimensions in Figure 2 to locate dishwasher's drain, water, and electrical connections•
2. All utilities must be routed in shaded area in the Figure 2
Note: Locate the electrical supply and dishwasher's electrical
junction box on right underside of unit behind kickplate
assembly• See Figure 4. Determine where you will connect
to hot water supply• Review Figure 4 and note the location of
water inlet valve. Determine where you will connect the drain hose.
3. Cut access holes for the Electrical, Water and Drain hoses in the cabinet within the shaded areas as shown in Figure 2.
4. The dishwasher operates on a 120 volt, 60 Hz electrical supply. Provide a separate circuit with a fuse or circuit breaker rated for at least 15 amps (20 amps if connected with disposer) but not
more than 20 amps.
5. Pull electrical cable through hole into installation area.
6. Be sure water inlet valve is protected from freezing. If valve freezes and ruptures, flooding may occur•
7. Determine amount of tubing needed to connect hot water supply to the unit's water inlet valve• Extra hose length is necessary
High-pressure and high-temperature Stainless Flexible hose with a minimum inner diameter of 1/4" may be used. A shut-off valve
installed outside dishwasher cabinet is best.
8. Route water supply line into installation area.
9. Stand dishwasher back upright for further installation.
IMPORTANT: Incoming hot water temperature should be at least 120°F (49°0). Water pressure should be between 20-90 psi.
333A,,
Adjustabl,
to 353A''
1. Measure height of cabinet opening from underside of countertop to floor.
. Move dishwasher to front of installation area.
Adjust the levelling legs.
Dishwasher Anchoring
4. Choose one of the methods of attachment below to secure unit, holes need to be pre-drilled using a Q5 drill bit regardless of
the option chosen:
a. Side Mount Cabinet Clips (Preferred Method of attachment) b. Top Mount Cabinet Clips (to be used when Side Mount
is not an available option)
CAUTION: Use extreme care .n mounting the dishwasher as to not
scratch, bump or otherwise damage the console or tub.
To install the Side Mounting Clips•
®
(_ To install using Top Mount Cabinet Clips:
Note: Install Side Mount Brackets before unit is installed
into the cabinet. Insert screws into the front holes of the clips only. Use extreme caution when fixing the screws,
not to cratch dishwashers or kitchen cabinet. (See image below)
Depending on the depth of cabinet, the Top Mount Clip have a break off point that can be removed if necessary.
NOTE: Install Top Mount Clips before unit is installed into the
cabinet. Screw clips firmly to top brace using screws provided in the literature pack. (See image below)
5. Carefully place dishwasher inside cabinet area such that is centered in opening. Use caution when moving dishwasher to
prevent damage to cabinet, dishwasher and floor.
6. Front of door needs to be even with the front of adjoining cabinets.
Front levelers should allow 5/16" (0,8 cm) below underside of
countertop to top of console.
7. Check that dishwasher is level from side to side by placing a level against the top front section of the tub. See Figure 7a.
-- ure
8. Adjust levelers up or down until dishwasher is level. See Figure 7b/c.
_ Figure 7b
Fig 7a _'
Figure 7e
_ Figure 8
Property Damage
Do not solder within 6" (15,24 era) of the water inlet valve.
Damage to the plastic parts in the valve may occur. Use care that no sealer, dirt, or other objects enter the valve.
Damage to the filter screen may occur.
Be sure the dishwasher is placed_where the water inlet
valve will _e.Fep£rrom freezing, if the valve freezes, it may
rupture aria noomng may occur,
Water Line
1. Flush water line before connecting itto water inlet valve to prevent early clogging of filter screen. Place a bunched towel
over end of lineto prevent splashing. Open water supply valve for a few seconds and let water drain into a pan. Turn off water
supply at shut-off valve,
2. Route water line to water inlet valve as shown in Figure 4.
3. While firmly pulling water supply line into 90° elbow, tightly connect water supply to water inlet valve. Supply line must be free of kinks, scales, chips, and lubricants.
4. Turn on water supply and check for leaks.
Electrical Supply
1. Remove junction box cover and pull house wiring intojunction box. See Figure 9
2. Use a UL listed conduit connector (not included) at box to stabilize wiring.
3. Connect incoming black lead to dishwasher's black lead,
incoming white lead to dishwasher's white lead and incoming
green lead to dishwasher's green lead with wire nuts. (See
Grounding instruction Warning). Wire nuts must be tight.
Figure 9
Electric Shock Hazard
Grounding Instructions: The dishwasher must be connected to a grounded metal,
permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and
connected to the appliance's equipment grounding terminal or Mad. it is the consumer's responsibility to contact a
qualified installer to make sure the electrical installation conforms with the National Electrical Code and local codes
and ordinances.
Do not connect the dishwasher to the power supply until the
appliance is permanently grounded. All wiring connections must be enclosed in the junction box. This unit has copper lead wires.
Joining aluminum building wire to stranded copper wire should be done by a qualified electrician using materials
recognized by UL and local codes.
Do not use an extension cord. Such use can result in fire,
electrical shock, or other personal injury.
Failure to follow these instructions could result in death or
serious injury.
Air Gap
3. If you connect to a sink trap,local codes may require you to install an air gap kit, (not included). The drain hose will be routed
from dishwasher to air gap inlet as shown in Figure 13 An air
gap kit is available from a plumbing supply store. (if the drain hose is installed through the floor, an air gap is necessary),
4. If you connect to a disposer, the large end of drain hose will fit. Figure 14 (a) The knock out plug must be removed from
inside disposer inlet before making the final fit to drain hose. See Figure 14 (b).
Larger end
Electric Shock Hazard
Disconnect electrical power at the fuse box
or circuit breaker box before beginning installation.
Failure to follow this warning could result in
death or serious injury
Cut Hazard
Metal color panels are sharp and should be handled with care. Wear gloves to protect
hands. Failure to follow this warning may result in
injury.
9. He|es need to be pre.drilleld using a 05 drill to secure unit
10. Screw mounting brackets firmly to cabinet using screws provided in installation packet. See Figure 8
11. Open and close dishwasher door slowly. Ensure that there is clearance to the console. Adjust accordingly, adjust rear foot if small correction is needed until door opens and closes freely.
Adjust the levelling legs.
Water Line
Electrical Line
[] check these items:
Water and electrical lines are straight out in front of the dishwasher.
All three leg levelers are positioned properly.
Cabinet Seals are positioned on the sides of the dishwasher.
[]
Cabinet Attachment Clips are attached to the cabinet on both corners on top of the dishwasher.
Green Wire to Green
(Ground)
4,
Replace junction box cover.See Figure 10
Option
f _ t Green Wire _J_@_
to Green Wire ,f_ f_
(Ground/
. . _ BlackWire ! X _,
Black Wire
to Black Wire
(Hot)
Figure 11
Wh'thiW'_/_/ire_ !_kWire _/ "X_f
Figure 10
=
Review Figures 12, 13 and 14 to see the different ways to connect dishwasher to drain system. Choose method that best suits your need.
Sink at Left j
Figure 12
The drain hose loop must be at least 32" (80 cm) high from the floor
to insure proper drainage.
2. if you connect to a sink drain, entry will need to be above trap. A "Y" branch tailpiece and connector kit, not included, will make this method easier and includes all needed fittings and instructions. See Figure 12,
White Wire to White Wire
(Neutral)
Entry Must be Above Trap
_V_
Branch
Tailpiece
Sink at Right
2"Drain Hose Hole
fits disposer
inlet fitting
Figure 14(a)
Sink at Left
Removg
Plug in Disposer
Figure 14(b)
The drain hose loop must be at least 32"(80 cm) high from the floor
to insure proper drainage.
Cut %"(1,6 era) connection.
Gap
Through
Fl_rimo Separate
Trap
Sink at Right
2" (5,08 cm) Drain Hose Hole
5. If the cabinet wall is wood, sand edges of hole until smooth and rounded. If cabinet wall is metal, cover all sharp edges with electrical or duct tape to avoid cutting drain hose.
6. Move unit back in place while routing drain hose through access hole. Use caution to prevent damage to the dishwasher, floor and
cabinets. IMPORTANT: Make sure there are no sharp bends
or kinks that might restrict drain flow.
7. Secure drain hose to sink drain, disposer, or separate trap with a
clamp, iMPORTANT: Be careful not to overtighten clamp or you may damage end of hose. Do not connect hose to
horizontal pipe between sink drain and disposer.
8. Be sure unit does not rest on drain hose. it should be free of electrical components and door springs. Do not cut corrugated
drain hose. Pull excess through cabinet and place under sink.
Make sure hose does not come in contact with any sharp edges.
Electric Shock Hazard
If all connections are correct, there are no leaks, and unit runs properly, replace the kick#ate assembly before placing unit into operation.
Failure to follow this warning could result in
electric shock.
[] Water and drain lines have no kinks and move freely
behind the dishwasher.
[] Water supply is turned on. n Joints are free of leaks.
[] Wiring connections to junction box are tight all access
panels are secured back in place.
[] Replace kickplate. See Figure 11 [] Drain hose is connected properly to outlet. [] All packing materials and consumer literature have
been removed from inside unit.
[] Dishwasher is level and securely fastened. [] Open and close door to make sure it does not hit
surrounding cabinet or countertop.
[] Make gqre that all wire ties are removed from the rack
assemDly
Operate the machine through at least one fill and pump-out,
checking the following items:
[] At first fill, approximately 4 minutes make sure water
completely covers filter surface.
[] At pump-out: (pump-out is either when the cycle is
completed or canceled, refer to the Use and Care Manual for Start/Cancel), make sure all water is pumped out.
[] Check water connections again for leaks.
Loading...