Electrolux CEW30GF6GBB, CEW30GF6GBC, CEW30GF6GBD, CEW30GF6GSB, CEW30GF6GSC Installation Guide

...

|nstallation |nstrucfions

Instructions d'installation

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER. iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

If the information in this manual is not followed

exactly, a fire or explosion may result causing property damage, personal injury or death.

FOR YOUR SAFETY:

-- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

-- WHAT TO DO iF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire department.

-- Installation and service must be performed bya qualified

installer, service agency or the gas supplier.

OVERALL

DIMENSIONS 25 3/4"

_- 30" --_-_

*Minimum to -- Side Wall

47-3/4"

Maximum 36 +1/8"

Side of on Either "5"-_

Range 5"

_! ,, Cabinets onli

.... _ .... of Range.

Refer to your serial plate for

applicable agency certification

Note." For appliances installed in the State of Massachusetts see page 2.

FRONT

VIEW

30" Minimum '_ Minimum to

Either Side

14-13"_1

Maximum Depth

for Cabinets Above Range Top.

36"

4r_

_ 30" _ 0" Clearance Be!ow Cooking Top and at Rear of Range.

Clearances and Dimensions

1. Location--Check location where the range will be installed. Check for proper electrical and gas supply, and the stability of the floor.

2. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact

surface must be solid and level.

Note: For operation at elevations above 2000 ft., appliance rating shall be reduced at the rate of 4 percent for each 1000 ft. above sea level.

Provide Proper Fuel Type

Before Proceeding: Your appliance was preset at the

factory to operate on Natural Gas only.

DO NOT attempt to convert this range to

L.P. (Propane) Gas. This appliance is designed to operate with Natural Gas only.

Franqais- Pages 9-16

Important Notes to the Installer

1. Read all instructions contained in these installation instructionsbefore installing range.

2. Remove all packing material from the oven compartments before connecting the gas and electrical supply to the range.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructionswith the consumer.

important Note to the Consumer

1. Keep these instructionswith your Use & Care Manual for future reference.

IMPORTANT SAFETY INSTRUCTIONS

installation of this range must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code ANSI Z223.1--1atest edition when installed in the United

States.

When installed in a manufactured (mobile) home, installation must conform with the Manufactured Home Construction and

Safety Standard, Title 24CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part 280)] or, when such standard is not applicable, the

Standard for Manufactured Home Installations,ANSI/NCSBCS A225.1, or with local codes.

This appliance has been design certified by CSA International. As with any appliance using gas and generating heat, there are certain safety precautions you should follow. You will find them in the Use & Care Manual read it carefully.

Be sure your range is installed and grounded properly by a qualified installer or service technician. This range must be electrically grounded in

accordance with local codes or, in their absence, with the National Electrical Code ANSI/NFPA No .70-

latest edition when installed inthe United States. See Grounding Instructions on page 5.

Before installing the range in an area covered with linoleum or any other synthetic floor covering, make sure the floor covering can withstand heat at least 90°F above room temperature without shrinking, warping or discoloring. Do not install the range over carpeting unless you place an insulating pad or sheet of

1!4-inch thick plywood between the range and carpeting. Make sure the wall coverings around the range can withstand the heat generated by the range.

Do not obstruct the flow of combustion air at the oven vent nor around the base or beneath the lower front

panel of the range. Avoid touching the vent openings or nearby surfaces as they may become hot while the oven is in operation. This range requires fresh air for proper

burner combustion. Air curtain or other overhead range hoods, which operate

by blowing adownward air flow on to a range, shall not be used inconjunction with gas ranges other than when the hood and range have been desgined, tested and listed by an independenttest laboratory for use incombination with

each other.

Never leave children alone or unattended

in the area where an appliance is in use. As children grow, teach them the proper, safe use ofall appliances. Never leave the oven door open when the range is unattended.

Stepping, leaning or sitting on the doors

or drawers of this range can result in serious injuries and can also cause damage to the range.

Do not store items of interest to children in the cabinets above the range. Children could be seriously

burned climbing on the range to reach items. To eliminate the need to reach over the surface

burners, cabinet storage space above the burners should be avoided.

Adjust surface burner flame size so it does not

extend beyond the edge of the cooking utensil. Excessive flame is hazardous.

Do not use the oven as a storage space. This creates a potentially hazardous situation. Never use your range for warming or heating the room. Prolonged use of the range without adequate ventilation can be dangerous. Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance. Explosions or fires could result. Reset all controls to the "off" position after using a programmable timing operation.

FOR MODELSWITH SELF=CLEAN FEATURE: * Remove broiler pan, food and other utensils before

self=cleaning the oven. Wipe up excess spillage. Follow the cleaning instructions in the Use & Care Guide.

* Unlike the standard gas range, THiS COOKTOP IS

NOT REMOVABLE. Donot attempt toremove thecooktop.

Special instructions for appliances installed in the State of Massachusetts: This appliance can only be installed in the State of Massachusetts by a Massachusetts licensed plumber or gas fitter. When using a flexible gas connector, it must not exceed 3 feet (.36inches) in length. A "T" handle type manual gas valve must be installed in the gas supply line to this appliance.

DO NOT MAKE ANY ATTEMPT TO

OPERATE THE ELECTRIC iGNiTiON OVEN DURING AN ELECTRICAL POWER FAILURE. RESET ALL OVEN CONTROLS TO "OFF" IN THE EVENT OF A POWER FAILURE.

The electric ignitor will automatically re-ignite the oven burner when power resumes ifthe oven thermostat control was left

in the "ON" position.

When an electrical power failure occurs during use, the

surface burners will continue to operate.

During a power outage, the surface burners can be lit with a match. Hold a lighted match to the burner, then slowly turn

the knob to the LITE position. Use extreme caution when

lighting burners this way.

Before Starting

Tools You Will Need

For leveling legs and Anti=Tip Bracket:

Adjustable wrench or channel lock pliers 5/16" Nutdriver or Flat Head Screw Driver

Electric Drill & 1/8" Diameter Drill Bit (5/32" Masonry Drill

Bit if installing in concrete)

For gas supply connection:

Pipe wrench

For burner flame adjustment:

Phillips head _ and blade-type screwdrivers

Additional Materials You Will Need

Gas line shut-off valve

Pipe joint sealant

A new flexible metal appliance conduit (1/2" NPT x 3/4" or 1/2"1. D.) must be design certified by CSA International.

Because solid pipe restricts moving the range we recommend using a new flexible conduit (4 to 5 foot

length) for each new installation and additional reinstallations.

A. Locate the Bracket Using the Template - (Bracket may

be located on either the leftor right side of the appliance. Use the information below to locate the bracket iftemplate is not available). Mark the floor or wall where left or right side of the range will be located, ifrear of appliance isagainst the wall or no further than 1-1/4" from wall when installed, you may use the wall orfloor mount method, ifmolding isinstalled and does not allow the bracket to fit flush against the wall, remove molding or mount bracket to the floor. For wall mount, locate the bracket by placing the back edge of thetemplate against the rear wall and the side edge of template on the mark made referencing the side of the appliance. Place bracket on top of template and mark location of the screw holes in wall. If rear ofappliance isfurther than 1-1/4" from the wall when installed, attach bracket to the floor. For floor mount, locate the bracket by placing back edge of the template where the rear of the range will be located. Mark the location of the screw holes, shown in template.

B. Drill Pilot Holes and Fasten Bracket - Drill a 1!8" pilot

hole where screws are to be located. If bracket isto be mounted to the wall, drill pilot hole atan approximate 20°

downward angle. If bracket is to be mounted to masonry or ceramic floors, drill a 3/16" pilot hole 1-3/4" deep. The screws provided may beused inwood or concrete material.

Use a5/16" nut-driver orflat head screwdriver to secure the bracket in place.

Always use the (2) newflare union adapters (1/2" NPT x 3/4" or 1/2" I.D.) supplied with the newflexible appliance conduit for connection of the range.

Normal installation Steps

1. Anti=Tip Bracket Installation Instructions

important Safety Warning

To reduce the risk of tipping of the appliance, the range must be secured to the floor by properly installeda nti-tip bracket and screws packed with the range. Failure to install the anti-tip bracket will allow the range to tip over ifexcessive weight is placed on an open door or if a child climbs upon it. Serious

injurymight result from spilled hot liquids or from the appliance itself.

Ifthe appliance isever moved to a different location, the anti-

tip brackets must also be moved and installed with the appliance.

instructions are provided for installation inwood or cement fastened to either the floor or wall. When installed to the wall,

make sure that screws completely penetrate dry wall and are secured inwood or metal. When fastening tothe floor or wall, be sure that screws do not penetrate electrical wiring or plumbing.

-Wan Mount

WallPlate

Floor Mount

FASTEN BRACKET (FLOORMOUNTINGONLY)

p Bracket

LevelingLeg--

Floor Mount _ p Bracket

1=1/4"

Wall

Level & Position Appliance- Level appliance byadjusting the (4) leveling legs with a wrench. NOTE: A minimum clearance of 1/8" is required between the bottom of the appliance and the leveling leg to allow room for the bracket. Use a spirit level to check your adjustments. Slide appliance back into position. Visually check that rear leveling leg is inserted into and fully secured by the Anti-Tip Bracket by removing lower panel or storage

drawer. For models with a warmer drawer or Bake-n- Warm TM Double Oven compartment, grasp the top rear

edge of the range and carefully attempt to tilt itforward.

"Recommended Area for

120V Outlet on Rear of Wall and Area for Thru

the Wall Connection of

Pipe Stub and Shut Off

Valve is Shaded Area.

(17rnrn)

Range Side J"

2. Provide an adequate gas supply.

This appliance is factory pre-set to operate on 4" natural gas manifold pressure. A gas pressure regulator is connected to the manifold and MUST be connected in series with the gas supply line.

Care must be taken during installation of the appliance not to obstruct the flow of combustion and ventilation air.

For proper operation, the maximum inlet pressure to the regulator should be no more than 14 inches of water column pressure. The inlet pressure to the regulator must be at least

1inch greater than regulator manifold pressure. Examples: If regulator is set for natural gas 4 inch manifold pressure, inlet pressure must be at least 5 inches.

the Floor Connection of Edge

-..4 Wall

Shut Off Valve.

Fig. 4a

Manual Flare Flexible Flare Union Pressure Shutoff Union Appliance Adaptor Regulator

Valve / Conduit |

off Service Shut-Off Valve Electric Ignition modelsonly _

(Shown in ON Position).

Be sure lever is in the "On" position when

installation is complete

Fig. 4b

Leak testing of the appliance shall be conducted according to the instructions in step 4g.

The gas supply line should be 1/2" or 3/4" I.D.

3. Seal wall openings.

Seal any openings in the wall behind the appliance and in the floor under the appliance after gas supply line isinstalled.

4. Connect the appliance to the gas supply.

NOTE: To prevent leaks use pipe joint sealant on all male (outside) pipe threads.

Gas

Regulator

Service

Shut-Off Valve

(shown in the

"ON" position.)

Fig. 4c

the 1/2" flare union adapter with an adjustable wrench before tightening the gas supply fitting and!or appliance conduit (Refer to Fig. 4e).

Install flare union adapter to external manual shut-off valve.

Attach appliance conduit to flare union on shut-off valve.

Make sure service shut-off vMve on pressure regulator is in the "ON" position (See Fig. 40.

Check for leaks. Turn the gas supply on to the appliance and use a liquid leak detector at alljoints and conduits to check for leaks in the system.

Do not use flame to check for gas leaks.

Fig. 4d

Fig. 4e

Checking Manifold Gas Pressure Disconnect the range and itsindividualshut-offvalve from the gas supply piping system during any pressure testing of that system at test pressures greater than 14" of water column pressure (approximately 1/2" psig).

The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 14"of water column pressure (approximately 1!2" psig).

If it should be necessary to check the manifold gas pressure, connect manometer (water gauge) or other pressure device to thetopburner right rearorifice. Usinga rubberhosewith inside diameter of approximately 1/4," hold tubing down tight over

orifice. Turn burnervalveon.

For an accurate pressure check have at least two (2)other top burners burning. Be sure the gas supply (inlet) pressure is at least one inch above specified range manifold pressure. The gas supply pressure should never be over 14" water column.

When properly adjusted for Natural Gas the manifold pressure

is 4."

Fig. 4f

DO NOT allow regulator to turn on pipe

when tightening fittings.

a) Install an external manual gas shut-offvalve to gas supply

line inanaccessible location outside of the range. Be sure you know where and how to shut off the gas supply to the appliance.

b) Install 1/2"flareunionadaptertopressureregulatorusing

NO MORETHAN 15ftJIbs. of torque

NOTE: Be sure to stabilize the left side of the pressure regulator with adjustable wrench before tightening ANY fittings to the pressure regulator (Refer to Fig. 4d).

c) Tighten the gas supply fitting and/or appliance conduit to

flare union on the right side of the pressure regulator using

NOMORE THAN 15ft./Ibs. of torque. Besure to stabilize

5. Read these electrical connection details first then connect electricity to appliance.

Before servicing, disconnect electrical

supply at circuit breaker, fuse or power cord.

Electric Requirements: A dedicated, properly grounded and polarized branch circuit protected by a 15amp. circuit breaker or time delay fuse. See serial plate for proper voltage.

Extension Cord Precautions: Because of potential safety hazards under certain conditions,

we strongly recommend against the use of any extension cord. However, if you still elect to use an extension cord, it is absolutely necessary that it be a UL listed 3-wire grounding type appliance extension cord and that the current carrying rating of the cord inamperes be equivalent to or greater than the branch circuit rating. Such extension cords are obtainable through your local service organization.

+ 12 hidden pages