Page 1
822 70 79-05
RA/RM-2D
0402
RM 6505
AES II
MANUAL CARAVAN
Italiano pagina 20
Deutsch Seite 3
English page 12 Nederlands pag. 29
Français page 38
Page 2
Page 3
OPERATING AND INSTALLATION INSTRUCTIONS
FOR ELECTROLUX REFRIGERATORS
INTRODUCTION
We are pleased that you have chosen this refrigerator
and hope you will derive muc h satisf action from using it,
but first a few well-meant words of advice:
It is important to read through these instructions carefully before using the refrigerator.
T o ensur e good refrigeration and economical oper ation,
the refrigerator must be installed and used as described
in these instructions.
The refrigerator is designed for installation in motorhomes.
This refrigerator comes with an
Automatic Energy Selector (AES)
which controls operation and energy supply. To put the
refrigerator in operation, just trip the main switch - AES
manages the rest.
TRANSIT DAMAGE
Inspect the refrigerator for damage. Transit damage
must be reported to whoever is responsible for delivery
not later than seven days after the refrigerator was
delivered.
DATA PLATE
Check the data plate, inside the refr igerator, to ensure
that you have received the right model.
The data plate contains e. g. the following details:
Model designation RM................................
Product number ......................................
Serial number ......................................
Volt age ...................................... volts
Gas pressure ...................................... mbar
Since these details will be needed if you hav e to cont act
service personnel, it is a good idea to make a note of
them here.
CONTENTS
OPERATING INSTRUCTIONS .. ......................... 13
CONTROLS ................................................... 13
STARTING THE REFRIGERATOR .............. 13
SWITCHING BETWE EN ENERGY
SOURCES ..................................................... 13
REGULATING THE TEM PERAT URE .... ...... 1 3
TRAVEL CATCH ........................................... 14
FOOD STORAGE .......................................... 14
ICE-MAKING .............. ........ ........ ........ ........ ... 14
DEFR O STING .. .................. .............. ............. 14
CLEANING THE REFRIGERATOR .............. 14
HEATING CABLE ......................................... 14
WINTER OPERATION .................................. 14
TURNING OFF THE REFRIGERAT OR ........ 14
IF THE REFRIGERATOR FAILS
TO WO R K .................... ................................ . 15
MAINTENANCE ............................................ 15
SERVICE .... .................... .................... .......... 15
INSTALLATION INSTRUCTION ....................... 15
REPOSITIONING THE HINGES ................... 15
DOOR PANEL ..................... ........ ........ ......... 15
INSTALLATI O N/BUI LDI NG -IN .. .... .... .... .... ... 16
VENTILATION OF THE UNIT ...... ...... ...... ..... 16
LP GAS CONNECTION ................................ 17
ELECTRICAL CONNECTION ...................... 18
TECHNICAL DATA ....................................... 19
12
Page 4
OPERATING INSTRUCTIONS
CONTROLS
FIG. 1
This refrigerator is equipped with an Automatic Energy
Selector (AES) which controls its operation and energy
supply.
The system selects the available energy source in the
order:
230-240 V - 12 V - LP gas
No manual operation is necessary for selecting the
energy source.
The control panel is shown in fig.1.
The refrigerator is set into operation by pushing button
(A) (main switch). The AES LED (C) lights green showing: AES system working. Push- button (B) is used for
setting the electronic thermostat. The thermostat LEDs
(D) shows the chosen temperatur e position. When there
is a demand for refrigerat ion, AES will connect the m ost
favourable of the available energy sources.
Note: 12 V must always be available to supply the
electronics.
STARTING THE REFRIGERATOR
All references are to fig. 1.
LP Gas operation
AES will select LP gas operation under the following
conditions:
• No AC (230-240 V) available
• Engine not running (no high current at 12 V DC
available)
• AC available but too low
• Engine running but DC supply too low
(condition three and four are briefly described in
item Undervoltag e operati o n)
When the system chooses LP Gas operation, the flame
failure device is automatically opened, allowing the gas
to flow to the burner. At the same time, the electronic
igniter is energized.
After initial installation, servicing, or changing gas cylinders etc., the gas pipes may contain some air that should
be allowed to escape by briefly turning on the refrigerator
or other appliances. This will ensure that the flame lights
immediately.
If the flame goes out (by gus t of wind etc. ), the ignit er is
immediately activated and reignites the g as .
Note: The control electronics and the ignit er m ust have
12 V DC supply to operate.
Gas trouble-s ho oting
If the AES LED (C) is flashing red, the system was not
able to start or continue gas operation. Set the switch
(A) to "OFF" and check that there is enough gas in the
gas bottle, that its valve is open and that any valves in
the gas line to the refrigerator are open.
Then push button (A) to "ON" again. After 10 sec. AES
will repeat the ignition sequence. When the AES LED
(C) again starts flashing red after 30 sec., the trouble
persists (air in the line, no gas?). Switch (A) briefly off
and then on again. It might be necessary to repeat this
operation 2-3 times if the tubing contains air (after
changing gas bottles, repairs etc.) .
If this does not help, you should consult a service
technician.
230-240 V Operation
When a mains connection is available, AES will select
this. Please note, that e v en being in AC mode, 12 V DC
is necessary for the internal supply of the electronics.
12 V Operation
AES will select the 12 V mode of operation only when
the vehicle engine is running (detect ed by the alt ernator
connection of the fridge D+).
SWITCHING BETWEEN ENERGY
SOURCES
When switching from one energy source to another,
there are some delays implem ented in the AES system.
The 15 min. de lay between s witching off the engine and
starting gas mode is intended to delay the starting of gas
mode e.g. when stopping at a filling station.
WARNING: It is not allowed to have a naked
flame at a gas filling station. If you are not sure,
that your stop is shorter than 15 min., you are
advised to switch off the main switch (A), fig. 1,
when stoppi ng at a fill ing stat ion .
Undervoltage operation
The AES system is designed to guarant ee the maximum
cooling efficiency under any circumstances. Therefore,
the system monitors continuously the voltage level while
being in either 12 V DC or 230-240 V AC mode. If the
voltage is too low, the system switches to Gas mode
shown by the yellow LE D (E in fig. 1.). T he system sta ys
in Gas mode, until the electrical supply voltage has
recovered to normal level.
REGULATING THE TEMPERATURE
The position number refers to fig. 1.
It will take a f ew hours for the r efrigerator to reach normal
operating temperature. So we suggest you start it well
in advance of a trip and if possib le store it with precooled
AC
E
D
B
13
Page 5
foodstuffs.
The temperature of the refr igerator main compartment
is set for all three sources of energy, by means of the
thermostat knob (B). After turning on the refrigerator the
system automatically chooses the mid- position. With
some experience you will soon find a suitable setting.
This normally does not need resetting because the
same thermostat controls the main compartment temperature for any of the three sources of energy.
TRAVEL CATCH
The refrigerator is equipped with two travel catches.
Make sure that both are engaged when the mot orhom e
is on the move.
FOOD STORAGE
Always keep food in closed containers. Never put hot
food in the refrigerator; allow it to cool first.
Never keep items in the refrigerator that might give
off flammable gases.
The frozen food comp artment is intended for the storage
of frozen food and for making ice. It is not suitable for
freezing items of food.
Never put bottles or cans of fizzy drinks in the frozen
food storage compartment as they may burst when
freezing.
Most kinds of frozen food can be stored in the frozen
food compartment for about a month. This period of time
may vary, however, and it is important to follow the
instructions on the individual packages.
ICE MAKING
Fill the ice tray to just below the brim with drinking w ater
and place it on the freezer shelf.
Ice will be made more rapidly if the thermostat is set at
its highest position, but be sure to mov e the thermostat
back to normal setting when the ice is formed, the
refrigerator might otherwise become too cold.
DEFROSTING
Frost will gradually accumulate on the refrigerating
surfaces. It must not be allowed to grow too thick as it
acts as an insulator and adversely affects refr igerator
performance. Check the formation of frost regularly
every week and when it gets about 3 mm thick, defrost
the refrigerator.
To defrost the refrigerator , turn it off and remov e the ice
trays and the food item, leave the cabinet and freezer
doors open.
Do not try to accelerate defrosting by using any kind of
heating appliance, as this might damage the plastic
surfaces of the refrigerator. Neither should any sharp
objects be used to scrape off the ice.
Defrost water runs from a collector channel to a receptacle at the rear of the refrigerator where it normally
evaporates.
Heavy frosts build up on the freezer plate and the cooling
fins, and a lot of defrost water, move the plastic drain
tube in to a watertight bucket or container. (Access
through the lower ventilation grill on the outside of the
motorhome). As the frost melts, the water will flow into
the container. Replace the drain tube to its original
position after defrosting.
Defrost water in the freezer compartment should be
mopped up with a cloth.
When the ice has melted, wipe the refrigerator dry and
restart it. Place the food items back inside but wait until
the refrigerator is cold before making ice cubes.
CLEANING THE REFRIGERATOR
Clean the inside of the refrigerator regularly to keep it
fresh and hygienic.
Soak a cloth in a solution consisting of a teaspoon of
bicarbonate of soda to half a litre of warm water. Wring
out the cloth and use it to clean the interior of the
refrigerator and its fittings.
Nev e r use de te r ge nt s , s co ur in g p o wd er, str o ngl y scente d
products or wax polish to clean the interior of the ref rigerator as they may damage the surfaces and leave a
strong odour.
The exterior of the refrigerator should be wiped clean
now and then, using a damp cloth and a small quantity
of detergent. B ut not the door gasket, which should only
be cleaned with soap and water and then thoroughly
dried.
The cooling unit behind the refrigerator should be
cleaned with a brush from time to time, but make sure
that the refrigerator is switched off when doing this.
HEATING CABLE
During the summer months of high temperatures and
humidity , the metal frame between the freez er and fresh
food compartments may have wat er droplets f orming.
This refrigerator comes standard with a 12 V (DC)
heating cable that will evaporat e the water droplets when
they form.
To have the heating cable on, you position the switch
located beneath the control panel to I. The heating cable
can be left on continuously or only used when temperatures require it.
Note: The heating cable will draw 12 V (DC) power
continuously when in the ON (I) position. It should be
turned OFF (0) when a charging source is not av ailable.
WINTER OPERATION
Please check that the ventilation grilles are not block e d
by snow, leaves etc.
ELECTROLUX ventilation grilles model L500, can be
fitted with winter covers, model WA130, to protect the
cooling unit against cold air. The covers may be fitted
when the outside temperature is below approx. 10°C and
should be fitted when the temperature is below the
freezing point.
We suggest that you fit the winter covers also in the case
that the vehicle is laid up during the winter months.
TURNING OFF THE REFRIGERATOR
If the refrigerator is not to be used for some time:
1. Set the switch (A), fig. 1, to "OFF".
2. Sh ut off any on-board valve in the gas line to the
refrigerator.
3. Empty the refrigerator. Defrost and clean it as described earlier . Lea ve the doors of the refrigerator
and frozen food compartment ajar.
4. When the motorhome is laid up for a long period of
time (e.g. during the winter months), we suggest
fitting the winter covers WA130 onto the vent grills.
14
Page 6
IF THE REFRIGERATOR FAILS TO WORK
Check the following points bef ore calling a service technician:
1. t hat the green A ES LED goes on, when the switch
(A) is set to "ON" (12 V must be available).
2. when mains are connected but the refrigerator stays
in gas operation: Is the refrigerator corr ectly con nected and is the fuse (230-240 V) intact?.
3. is the 12 V fuse intact?
4. Disconnect the wall plug, and the 12 V wires
before servicing. Check the fuses on the circuit
board, (under the black cover at the top of the refrigerator and behind the control panel).
Remove the two screws holding the control panel,
pull out the control panel with its electronics. Remove
the cover and check the fuses.
5. if the refrigerator does not operate in DC mode when
the engine is running:
Is the alternator (D+) connection ma de corr ectly?
6. i f the AES LED (C) flash es red: see chapter Gas
trouble-shooting .
If the refrigerator is not cold enough it may be
because:
1. The ventilation is inadequate owing to reduced area
of the ventilation passages (partial blockage of grilles
from wire mesh etc.).
2. The evaporator is frosted up.
3. The temperature control setting is incorrect.
4. T he gas p ressure is inc orrect - check the p ressure
regulator at the gas container.
5. The am b ie n t tem peratur e i s t o o h i g h.
6. Too much food is loaded at one time.
7. The door is not properly closed or the magnetic
sealing strip is defective.
If the refrigerator still does not work properly, call a
service technician.
WARNING! The sealed cooling system must not
be opened, since it contains corroding chemicals under high pressure.
MAINTENANCE
Always turn to a qualified service technician who is
familiar with LP gas systems and refrigerator.
We recommend that a service technician check the
refrigerator once a year .
• Check that the gas safety shut-off valve is wor king
properly.
• The ventilation openings are unobstructed.
• The Instruction Manual is available.
• Check all connections in the LP gas system for gas
leaks. Connections can be tested for leaks using a
soap solution. Do not use a naked flame! If there is
any suspicion of damage, call f or a service technician.
• Check that the burner is clean and free from combus-
tible material.
SOME USEFUL HINTS
Make sure that:
• Defrosting is carried out periodically
• The refrigerator is clean and dry with the door left
open when it is not to be used for some time.
• Liquids or items with a strong odour are well pack ed.
• The ventilation openings are unobstructed.
• The doors are secured by means of the both travel
catches when the carav an is on the mov e.
SERVICE AND SPARE PARTS
Service and spare parts are obtainable from your dealer
or Electrolux - consult the telephone directory.
INSTALLATION INSTRUCTIONS
REPOSITIONING THE HINGES
The refrigerator is equipped with reversible doors .
A special door rev ers ing kit m ust be used to re v erse th e
doors.
For further inf ormati o n , contact your d ealer or Electrolux.
DOOR PANEL
Door panels can easily be fitted or changed. The dimensions of the panels must be:
Model RM 6505
Height upper door 265 ±1mm
lower door 833 ±1mm
Width 483 ±1mm
Thickness max. 4 mm
Before starting the mounting work, check that the panel
dimensions are in compliance with those given in the
table and the instructions are read thoroughly.
When mounting the panel, proceed as follows:
Upper doo r
• remove the two screws holding the control panel
• unscrew the upper hinge pin and remove the door
• unscrew the upper part of the door frame, remove t he
old panel
• insert the new panel a n d push th e panel d o wnwards
• fasten the upper part of the door frame with its three
screws
• please note that the panel must be changed on the
lower door , befor e the upper door can be mounted
Lower door
• unscrew the middle hinge pin and remove the door
• unscrew the lower part of the door frame, remove the
panel stop (2x) and remove the old panel
• insert the new panel and push the panel upwards, put
the panel stop back in place and fasten the lower part
of the door frame with its three screw s
• replace the lower door
15
Page 7
• replace the upper door
• replace the control panel with its two screws.
INSTALLATION/BUILDING-IN
The refrigerator is intended for installation in a motorhome, and the description relates to this application.
The refrigerator must not be exposed to radiated heat
from hot objects.
Excessive heat irradiation impairs performance and
leads to increased energy consumption. F or this reaso n
the refrigerator should be installed if possible not at the
entrance side of the vehicle - normally orientated south
and often with an awning which would impair the dispersion of heat and combustion gases from the ventilation
openings.
It is not a good practice to install the refriger ator s o that
the vent openings are cov ered by the v ehicle’ s entranc e
door when this is set open. This would reduce the
ven til ati on ai rflo w t o the cool ing uni t an d reduce refrigeration performance.
The enclosure
The refrigerator must be installed in a substantial
enclosure and must be lev el, the dimensions are sho wn
in TECHNICAL DATA.
The bottom of the enclosure must be horizontal and e ven
so that the refrigerator can be easily pushed into place.
It must be sturdy enough to carry the weight of the
refrigerator.
Battens must be installed at the bottom, sides and top
of the enclosure and fitted with sealing strips.
Slide in the refrigerator until it is flush with the front of
the recess. There must be 10-20 mm free space behind
the refrigerator
Six fasteners are fitted in plastic bushings in the side
walls of the refrigerator , fig. 2. The y are used for securing
the refrigerator in the enclosure.
The side walls of the enclosure and/or any wooden
braces installed to hold the refrigerator must be dimensioned to seat the screws securely, also considering th e
forces due to the movem ent of the vehicle .
With the refrigerator in place, drive the screws through
the li nin g of the refri ger ator i nto the wa lls o f the enclosure.
There must not be more than 3 mm of clearance between refrigerator and enclosure on each side. If necessary, wooden strips or similar should be fitted.
Note: This is the only approved means of securing the
refri ger ator to the en cl o sure an d to the v eh ic le . Fasteners
penetrating other parts of the insulation (PU) foam of the
refrigerator might damage components like electric
wiring etc.
VENTILATION OF THE UNIT
At high ambient temperatures the refrigeration unit will
only perform adequately when properly ventilated.
Side ventil ation.
The refrigerator unit is ventilated via two openings in the
wall of the motorhome (fig. 3a).
Fresh air enter s through the lower opening and warm air
is discharged through the upper one.
The lower opening should be located a t floor level (to
allow any leaking gas to escape to the outside).
The upper ventilation opening should be located above
the condenser, as high as possible, to ensure good
ventilation.
Roof ventilation
The ventilation of the cooling unit can also be done via
one opening in the wall of the motorhome and one on
the roof for the roof vent (f ig. 3 b).
Fresh air enter s through the lower opening and warm air
is discharged through the roof vent.
Ventilation grilles
We recommend fitting 2 side vents, model L500,
alternative one L500 and one roof vent model R500,
which are specially developed by Electrolux for this
purpose.
The L500-ventilation grilles permit inspection and sm all
repa i rs to be c ar rie d ou t without the necessity to remove
the refrigerator from the recess.
FIG. 2
16
Page 8
Removal of flue gases
The ventilation passage at the rear of the recess, between the outer wall of the motorhome and the refrigerator (fig. 3a/b/c), must be sealed off against the living
space, so cold draughts are excluded (winter camping)
and no flue gases can penetrate into the motorhome.
The flue gases are dispersed through the upper vent
grille or the roof vent together with the ventilation air.
The top, bottom and sides of the ventilation passage
should be insulated to prevent condensation and cold
draughts.
Ventilation heights
Minimum ventilation heights in mm.
Model Installation with
Upper side vent L205 Upper side vent L500 Roof vent R500
Lower side vent L500 Lower side vent L500 Lower side vent L500
RM 65 05 1400 1400 1250
LP GAS CONNECTION
The refrigerator is designed for operation on LP gas, the
press ure of whi ch must be 28 mbar f or Butan e and 37 mbar
for Propane. Chec k that this is stated on the data plate.
The refrigerator is not design ed for operati on on
town gas or natural gas.
VENTILATION OF THE UNIT
min. ventilation
height
min. 510
Condenser
20
40
385
60
FIG . 3 a
Sealing gasket
e.g. of V-type
Batten
attached to
the floor
Sealing gasket
e.g. of V-type
This piece is
already on the
refrigerator
Cut out opening for the
side vent L500
is 341 x 451 mm
Floor
Cut out opening for the
side vent L500
is 341 x 451 mm.
L205 is 156 x 451 mm.
min. ventilation
height
min. 510
Condenser
FIG . 3b
Cut out opening for the
side vent L500
is 341 x 451 mm
Cut out opening for the
roof vent R500
is 87 x 507 mm
Door
20
FIG. 3c
Batten attached
to the side wall
Sealing gasket
e.g. of V-type
View from above
17
Page 9
CAUTION! CHECK THAT THE GAS SUPPLIED
TO THE REFRIGERATOR IS AT THE CORRECT
PRESSURE. SEE THE REDUCING VALVE ON
THE LP GAS CONTAINER.
The gas installation should only be carried out by a
person experienced in gas fitting. It is recommended that
the gas pipe feeding the refrigerator is so arr anged that
it is possible to turn off the supply of the refrigerator.
It must be of a type approved for use with continuously
operating bottled gas appliances, and have threaded
compression connections throughout. PUSH-ON CONNECTIONS MUST NOT BE USED (We do not recommend the use of "rubber" type flexible tubing for
connecting permanently operating appliances of this
type in the United Kingdom). All connectors etc. should
be of a type specifically designed for the type and
diameter of the connection pipe used, and screwed
joints should be seale d with a joinin g compo und approve d
for use with bottled gas.
The gas supply pipe should be connected to the gas inlet
pipe (outside diameter 8 mm.) by means of a suitable
gas-tight compression fitting, e.g. olive.
In making the connection to the refrigerator, a union gas
cock of an approved type bottled gas must be incorporated in the supply line in a position that is readily
accessible to the user. F or e v entual servicing purposes,
the union should be on the outlet side of the cock and
the pipework should be positioned so as not to prevent
the refrigerator from being readily withdrawn.
On completion of installat ion , the system must be
pressure tested by a qualified tech nician .
ELECTRICAL CONNECTION
The electrical installation must be carried out in a proper
and durable manner; taking into accounts all relevant
regulations and codes of practice. For mains voltage
operation, it is important that the circuit to and in the
motorhome is effectiv ely earthed.
For connection to a 230-240 V electricity supply, the
refrigerator has a 3-core mains lead which is intended
for connection to a properly earthed plug and socket
outlet. The soc ket o utle t sho uld b e fi tted in th e motorhome
in a position readily accessible to the user, within reach
of the mains lead. In the United Kingdom, the plug and
socket outlet should be of the non-reversib le type.
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as
follows:
- the wire which is coloured Green and Yellow must be
connected to the terminal in the plug which is marke d
with the letter E or by the earth symbol , or
coloured Green or Green and Yellow,
- the wir e which is coloured B lue must be connected t o
the terminal which is marked with the letter N or
coloured Black,
- the wire which is coloured B rown must be connecte d
to the terminal which is marked with the letter L or
coloured Red.
WARNING- THIS APPLIANCE MUS T BE EARTHE D
IMPORTANT
The wires in this mains lead are coloured in accordance
with the following code:
- green/yellow: ear th
- blue: neutral
- brown: live
In the United Kingdom, the plug or circuit to the refrigerator must be fitted with a fuse not greater than 5 amps.
If a 13 amp. (B .S. 1363) fused plug is used, it should b e
fitted with a 3 amp. fuse, ASTA approved to B.S. 1362.
In other countries, the fuse rating will depend upon the
voltage and local practice.
230-240 V Supplies.
Check that the voltage stated on the data plate is the
same as the main voltage in use (230-240 V).
Plug the 230-240 V refrigerator power cord into an easily
accessible wall socket .
Electrical leads must be routed and secured so
that they cannot come into contact with hot or
sharp parts of the refrigerator.
12 V and "D+" Connection
The 12 V connection of the refrigerator is shown in
fig. 4. The (+12 V) and (-) pole have to be connected
directly to the "house batter y". Do not use the chassis
for the return lead.
12 V supply must not be connected to a v oltage controller or similar device as the AES itself monitors the DC
voltage.
+12 V should be permanent attached, and must not be
cut out when the ignition key is turned off.
All connections should be screwed or soldered to k eep
voltage drop to a minimum. The positive conduct or must
be protected by a 20 A fuse.
The connection D+ (altern ator) has to b e connected
to the corresponding outlet o f the vehicles electrical
system.
FIG. 4
D
12V DC
18
Page 10
Cross-sections
The D+ (alternator) is a signal cab le and therefor e 1-1.5
mm
2
is sufficient.
Connection to 12 V + and - must be done with a 10 mm
2
wire if the total wire length (+ and - wire together) is
maximally 12 m.
If longer wires are required a bigger cross-s ection cab le
is needed.
Please consult a specialist, if you are not familiar with the 12 V electrical system in your motor
home.
Interior lig ht - bulb - change
If the bulb has to be replaced, proceed as follows:
1. Remove the cover from the lamp body by pushing it
backwards.
2. Remove the bulb.
3. Put in a new bulb (12 V, max. 5 W).
Spare part number for bulb: 200 72 90-03.
4. Push the lamp cover back in place.
TECHNICAL DATA
RM 6505
Overall dimensions, refrigerator
Height (incl. contr ols) .................. 1245 mm
Width .......................................... 525 mm
Depth (incl. cooling unit)
with door ..................................... 545 mm
without door ................................ 495 mm
Recess dimensions
Height ......................................... 1248 mm
Width .......................................... 530 mm
Depth .......................................... 510 mm
Capacity
Gross .......................................... 135 litres
Net ...................................... ........ 124.5 litres
Frozen food com partment .......... 23.5 litres
Weight (without pack aging) ........ 44 kg
Electrical data
Input 230-240 volt .................. 220 watt
12 volt .................. 175 watt
* Energy consumption (in 24h) ... 3 kWh
LP gas data
Input, max. ............ .......... ........ .... 0.34 kW
* Energy consumption (in 24h) ... 300 g
Cooling medium: Ammonia
* Average consumption in 24 h at 25°C mean annual
ambient temperature according to ISO standards.
Subject to alteration without notice.
Wiring diagram RM 6505
19
Page 11
MO-FO 0238
Loading...