thermaline S90
ELECTRIC SOLID TOP COOKERS
FOURNEAUX ÉLECTRIQUES AVEC PLAQUES Á GRANDE SURFACE
US INSTALLATION- AND OPERATING INSTRUCTIONS page 3
FR INSTRUCTIONS D’INSTALLATION ET D’EMPLOI page 11
Doc. 62.9582.01_UL
Edition 1
01.2006
Against wall - contre une paroi
Connections - Raccordement
Gas - Gaz
Fig.1 INSTALLATION DRAWINGS - PLANS D'INSTALLATION
Doc. 62.9582.01_UL
Free standing - isolé
operated from both sides - ulilisable des deux côtés
Connections - Raccordement
Gas - Gaz
Fig.1 INSTALLATION DRAWINGS - PLANS D'INSTALLATION
Doc. 62.9582.01_UL
CONTENTS
I. GENERAL INFORMATION................................................................................................. 3
II. INSTALLATION INSTRUCTIONS....................................................................................... 4
III. OPERATING INSTRUCTIONS............................................................................................ 8
SOMMAIRE
IV. INSTRUCTIONS GÉNÉRALES......................................................................................... 11
V. INSTRUCTIONS RELATIVES À L'INSTALLATION......................................................... 13
VI. INSTRUCTIONS DE FONCTIONNEMENT....................................................................... 17
62.9582.01_UL Page 1
I . GENERAL INFORMATION
GENERAL INFORMATION
1. INSTRUCTIONS FOR SAFETY AND USE
1.1 INSTALLATION AND INITIAL OPERATION
S The installation, adjustment and initial
operation of the appliance must be properly
carried out in accordance with the
manufacturer's instructions and may only be
done by an authorised specialist.
S Installations for the supply of electricity must be
carried out by qualified installers in accordance
with the specific national and local regulations.
They bear the responsibility.
S The appliance must not be placed in operation
until the user has become familiar with its
operation. The operating instructions and the
related safety precautions must be followed
precisely. Follow strictly the attention and
warning label indications on the appliances.
1.2 OWNER'S OBLIGATIONS
S The manager is responsible for ensuring that
all components relevant for safety are in
perfect working order at all times. The
operating condition of these components must
be examined by an authorized technician at
least once a year and any defects remedied if
required.
S The operator of this appliance is responsible
for total observation of the national regulations
concerning operating safety.
S Remain the manual for future reference.
1.3 USE AS PRESCRIBED
S Closed containers (jars, cans, bottles, tubes,
etc.) must not be heated owing to the danger of
bursting and injuries.
S Do not place any other objects apart from
cooking vessels on the ceramic plate since
they heat up during operation (danger of fire
and burning).
S The hot plates must not be used as rest
surfaces.
1.4 SAFETY-CONSCIOUS WORKING
S Touching the hotplates can cause burns.
S Keep a minimum distance of 16 inch (40 cm) to
the appliance, in order to a safety opening of
the oven door.
S Do not touch the curves of the oven door han-
dle, it can be hot. Use always the straight part.
S Spraying the appliance or its parts with a high-
pressure cleaning device may cause
malfunctions and is not to be done.
S To avoid damages of the appliance do not let
water flow from the mixer tap onto the cooking
plates.
S For appliances with a downpipe, the hose
should lead into a drain opening which is covered by a grating such that it cannot be kicked
or tipped, or a drain gutter should run underneath the appliance.
S Devices on wheels set up in block configuration
must be checked before each start-up whether
the potential equalization is connected with the
neighbour equipment. The connection may be
done only by authorized technical personnel.
S Appliances on wheels must be fastened to the
building.
1.5 AFTER-SALES SERVICE AND REPAIR
S In the event of a permanent fault which
interferes with operation, the appliance must be
switched off and disconnected from the power
supply.
S To perform maintenance and repairs contact
the factory, the factory representative or a local
service company.
S Repair, maintenance work and other
adjustments are only to be carried out by an
authorized specialist. The valid local and
national regulations must be observed. This
applies especially to safety and control
elements. Parts requiring replacement are only
to be replaced by original spare parts. A
service contract is recommended.
S Cleaning and maintenance must be done only
when the heating surfaces are cold. Do not use
inflammable liquids to clean the appliance.
S An obligatory service check is required
annually.
2. TECHNICAL DATA
PNC
Appliances
9CHG584140 WLWRAFOOOO 208
9CHG584141 WLXRAFOOOO 240
9CHG584142 WLWRAAOOOO 208
9CHG584143 WLXRAAOOOO 240
9CHG584144 WLWRABOOOO 208
9CHG584145 WLXRABOOOO 240
9CHG584146 WLWWAFOOOO 208
9CHG584147 WLXWAFOOOO 240
9CHG584148 WLWWCFOOOO 208
9CHG584149 WLXWCFOOOO 240
9CHG584150 WLWWAAOOOO 208
9CHG584151 WLXWAAOOOO 240
9CHG584152 WLWWCAOOOO 208
9CHG584153 WLXWCAOOOO 240
9CHG584154 WLWWABOOOO 208
9CHG584155 WLXWABOOOO 240
9CHG584156 WLWWCBOOOO 208
9CHG584157 WLXWCBOOOO 240
Appliance type
Voltage
Width
Depth
Height
V
inch
19.7
35.4
35.4
39.4
35.4
35.4
mm
500
900
900
1000
900
900
Coo-
Range Oven
king
zones
28
416
Power
in kW
5
5
5
3. PACKAGING
All the packaging materials used are environmentally friendly.
They may burnt at an incineration plant or sent for recycling.
4. TESTS / CERTIFICATES
All electrical appliances are UL 197 tested.
The appliance noise level is negligibly low. The statutory
guidelines are met; the noise level is less than 70 dB (A).
5. SPECIFICATION PLATE
The specification plate (E) is located in each case inside and
outside on the right of the operator panel (C) (Page 5 Fig. 5).
The serial number is marked on the type plate. The 8 digits
give following information:
Y last digit of the year of production
WW week of production
XXXXX running number
62.9582.01_UL Page 3