Please read these user instructions carefully.
Please observe the safety instructions on the first few pages of these
user instructions! Please keep these user instructions for later reference.
Pass them on to any subsequent owner of the appliance.
The warning triangle and/or specific words (Warning!, Caution!,
1
Important!) are used to highlight instructions that are important for
your safety or for the function of the appliance. It is imperative that
these instructions are observed.
0 This symbol or numbered instruction steps lead you step by step
through the operation of the appliance.
Next to this symbol you receive additional information and practical
3
tips on using the appliance.
Tips and instructions for the economical and environmentally conscious
2
use of the appliance are marked with a clover leaf.
In the event of a malfunction, these operating instructions contain
information on how to rectify faults yourself, see the "What to do, if..."
section.
If these instructions are insufficient, please contact your AEG Service
Force Centre.
In this respect please read the chapter "Service & Spare Parts".
2
nted on paper manufactured with environmentally sound processes.
The safety aspects of AEG electrical appliances comply with accepted
technical standards and the German Appliance Safety Law. Nevertheless, as a manufacturer we consider it our obligation to make you
aware of the following safety information:
Installation, Connection and Placing into Operation
• The dishwasher may only be transported upright.
• Check the dishwasher for transport damage. Do not in any circumstances connect an appliance that is damaged. In the case of damage,
please contact your retailer.
• Before installing the appliance, ensure that the nominal voltage and
type of supply on the rating plate match that of the supply where the
appliance is to be installed. The fuse rating is also to be found on the
rating plate.
• For information on how to correctly install and connect up your dishwasher, please read the “Installation“ section. Adaptors / connectors
and extension cables must not be used.
Child Safety
• This appliance is designed to be operated by adults. Children should
not be allowed to tamper with the controls or play with the product.
• Keep all packaging away from children.
• Keep all detergents in a safe place out of children’s reach.
• The water in your dishwasher is not suitable for drinking. If there are
still remnants of detergent in the appliance, there is a risk of burns!
• When disposing of an old appliance, cut off the power supply cable
and remove any door catches, to prevent young children being
trapped inside.
General Safety
• Repairs to the dishwasher are only to be carried out by qualified service engineers. Improper repairs can give rise to significant hazards for
the user. If your appliance needs repairing, please contact your local
AEG Service Force Centre.
5
Operating Instructions
• Never place the dishwasher in operation if the mains cable, water
inlet or drain hose is damaged; or the control panel, work top or
plinth area is damaged such that the inside of the appliance is freely
accessible.
• If the mains lead is damaged, or is to be replaced for a longer lead,
the cable (obtainable from AEG Service Force) must be replaced by a
service engineer authorised by AEG.
• Never unplug the appliance by pulling on the cable, always pull the
plug.
• Additions or modifications to the dishwasher are not permitted for
safety reasons.
• Ensure that the door of the dishwasher is always closed when it is not
being loaded or unloaded. In this way you will avoid anybody tripping
over the open door and hurting themselves.
• Long bladed knives stored in an upright position are a potential hazard.
• Long and/or sharp items of cutlery such as carving knives must be
positioned horizontally in the upper basket.
• When finished loading or unloading, close the door as an open door
can be a hazard.
Correct Use
• Only wash household dishes using the dishwasher. If the appliance is
used for other purposes, or is used incorrectly, the manufacturer cannot accept any liability for any damage caused.
• Only use detergents specifically designed for use in domestic dishwashers.
• Do not put any solvents in the dishwasher. There is a risk of an explosion!
• The anti-flood system provides dependable protection against damage due to leaks. For this system to function correctly, the following
preconditions must be met:
– The appliance must remain connected to the mains even when it is
switched off.
– The dishwasher must be correctly installed.
– Always shut off the water supply at the tap when the dishwasher is
not to be used for longer periods, e.g. when you are away on holiday.
• Do not sit or stand on the open door, the appliance may tip over.
6
Operating Instructions
• In the event of a fault, first close the tap, then switch off the appliance and unplug it from the mains. If the appliance is permanently
wired to the mains: remove the fuse.
2 Disposal
Disposing of the Packaging Material
Dispose of the dishwasher packaging material correctly. All the packaging materials used are harmless to the environment and can be recycled.
• Plastic parts are marked with standard international abbreviations:
– >PE<for polyethylene, e.g. sheet wrapping material
– >PS<for polystyrene, e.g. padding material (always CFC-free)
– >POM< for polyoxymethylene, e.g. plastic clips
• Cardboard packaging is manufactured from recycled paper and
should be deposited in the waste paper collection for recycling.
Disposal of Old Appliances
When disposing of old appliances, remove the plug and ensure that any
locks or catches are removed to prevent young children becoming
trapped inside.
Use an authorised disposal site.
2 Economical and Ecological Dishwashing
• Ensure that the water softener is correctly adjusted.
• Do not pre-rinse dishes under running water.
• When you wash a small load, the load sensor calculates the amount
of water necessary and shortens the programme. It is more economical to always wash with a full load.
• Select the wash programme to suit the nature and degree of the soiling on the dishes.
• Do not use more detergent, special salt or rinse aid than is recommended in these operating instructions and by the detergent manufacturer.
7
Operating Instructions
Appliance Features, Display and Control
Panel
Top Spray Nozzle
Rubber Seal for
Connecting the
Water Feed to the
Spray Arm
Spray Arms
Water Hardness Switch
Container for
Special Salt
Container
for Rinse Aid
Detergent
Dispenser
Display and Control Panel
Rating plate
Filters
8
Display and control panel
Operating Instructions
Function buttons
1
2
3
Set start
delay
Display Set
start delay
Indicator for End of Wash Programme
Control Indicators ON/OFF button
Function buttons: In addition to the dishwashing cycle the following
functions can also be set with the help of these buttons:
Function button 1Set water softener
Function button 2Activate/deactivate rinse aid inflow
Function button 3Activate/deactivate acoustic signal
Control indicators have the following meanings:
J
H
Refill special salt
Refill rinse aid
The indicators are never illuminated while a dishwashing cycle is run-
3
ning.
Prior to using for the first time
Prior to using for the first time, remove all the clips with which the
baskets are secured for transport. Then perform the following steps:
0 1. Adjust the water softener
2. Fill the water softener with water and special salt
3. Fill the rinse aid dispenser with rinse aid
Special salt and rinse aid must not be added if you use 3-in-1 detergent
3
tablets.
9
Operating Instructions
Water softener
To avoid scale deposits on the dishes and in the dishwasher, the dishes
must be washed with soft water, i.e. water with a low lime content. The
dishwasher therefore has a built-in water softener, in which tap water
with a hardness of 4°d (German degree) and harder is softened with the
aid of special salt.
Your water supplier will be able to inform you about the hardness and
3
hardness range of the water in your area.
The water softener can be set manually using the water hardness
switch; it can also be set electronically using the buttons on the control
panel.
Water hardness
2
In °d
51 - 70
43 - 50
37 - 42
29 - 36
23 - 28
19 - 22
15 - 18
11 - 141,9 - 2,5II33
4 - 100,7 - 1,8I/II22
under 4under 0.7I
1) The water hardness will only be indicated acoustically if the acoustic signal has
been activated.
2) (°d) German degree, measure of the hardness of water
3) [mmol/l] millimol per litre, international unit for the hardness of water
4) On this setting the length of the dishwashing cycle may be slightly longer.
*) Factory setting
In mmol/l
9,0 - 12,5
7,6 - 8,9
6,5 - 7,5
5,1 - 6,4
4,0 - 5,0
3,3 - 3,9
2,6 - 3,2
3
RangeManuallyElectronically
IV
III
Adjusting the hardness
setting
4
10
1
0*
9
8
7
6
5
4*
1
no salt
necessary
Number of
flashes and
acoustic signals
10
9
8
7
6
5
4
1
1
10
Operating Instructions
Setting the water softener
Using the table as a guide, adjust the water softener to that which corresponds to the hardness of the water in your area:
0 The dishwasher must be switched off.
Setting manually:
1. Open the dishwasher door.
2. Remove the lower rack from the
dishwasher.
3. Turn the hardness range switch to 0
or 1 (see table).
4. Replace the lower rack.
Setting electronically:
5. Press the ON/OFF button.
The LED indicators for all programme buttons (and the button for the
delay start timer if present) light up. The LED indicators and any option
buttons that are present only light up if they are activated.
If the only LED indicator illuminated is one that belongs to a pro-
3
gramme button, this means that this dishwashing cycle has been activated. The dishwashing cycle must be cancelled:
Press function buttons 2 and 3 simultaneously for approx.1 second.
The LED indicators for all programme buttons (and the button for the
delay start timer if present) light up. The LED indicators and any option
buttons that are present only light up if they are activated.
6. Press function buttons 2 and 3 simultaneously and keep them pressed.
The LED indicators for function buttons 1 to 3 will flash.
7. Press function button 1.
The LED indicator for function button 1 will flash. The LED indicator for
the end of the dishwashing cycle is flashing and acoustic signals can be
heard simultaneously (only when the acoustic signal has been activated):
– The number of times that the LED indicator for the end of the cycle
flashes and the number of acoustic signals correspond to the new
hardness setting.
– This sequence of flashes and acoustic signals is repeated many times,
with a 5 second pause in between.
11
Operating Instructions
8. Pressing function button 1 increases the hardness setting by 1.
(Exception: hardness setting 1 follows hardness setting 10).
9. When the hardness setting is correct, press the ON/OFF switch.
The hardness setting is now saved.
Special salt for the water softener
If the water hardness in your area is less than 4 °d, then the water in
3
your dishwasher does not need to be softened and you do not need to
use special salt or salt substitute.
Water can be softened in one of two ways:
• If you are using dishwasher detergent that already contains salt sub-
stitute, the detergent only is put into the detergent compartment.
– In this case the water softener must manually be set to 0 and
electronically to 1 to ensure that no special salt is added.
• If you are using dishwasher detergent and special salt separately, the
special salt is to be put into the salt container.
– In this case the water softener must manually be set to 0 and
electronically to between 2 and 10 (depending on the water
hardness in your area) to ensure that the special salt is dispensed
from the salt container.
12
Only use special salt intended for dishwashers. Never fill the salt supply
1
container with different types of salt (e.g. cooking or table salt) or
detergent. This would destroy the water softener.
Prior to filling with salt, please check each time that you really do have
a packet of special salt in your hand.
Setting the amount of special salt to be added
Some appliances are equipped with an additional 3in1 function.
3
If you use 3-in-1 dishwashing tablets and select the 3in1 function
together with the programme, the inflow of special salt does not have
to be deactivated (see ”3in1 function”).
Operating Instructions
0 1. Set the water softener manually and electronically to the desired water
hardness:
Manual
setting
011Do not add special salt.
0 - 12-102 to 10
If the water softener is electronically set at “1” for the purpose of using
3
detergent that includes special salt, the special salt indicator is deacti-
Electronic
setting
Number
of flashes
Addition of special salt
Addition of special salt
via salt container
(factory setting)
vated.
Adding special salt
If you are using dishwasher detergent and special salt separately, add
the special salt:
– Before using the dishwasher for the first time.
– When the indicator for special salt
panel.
0 1. Open the door, remove the lower
basket.
2. Undo the lid on the salt container by
turning it anticlockwise.
3. When using for the first time:
fill the salt container with water.
4. Place the funnel supplied on the container opening.
Fill the container with salt through
the funnel; the capacity of the container is approx. 1.0-1.5 kg depending on the grain size. Do not overfill
the salt container with salt.
Jis illuminated on the control
SALE
SALT
SALZ
SEL
The water expelled by filling the salt container with salt runs out of the
3
salt container onto the base of the washing compartment. This is not a
cause for concern, the water will be pumped out at the start of the
next wash programme.
5. Clean any salt remnants on the container opening.
13
Operating Instructions
6. Turn the lid clockwise to the stop, otherwise dishwasher salt will leak
into the wash water, this could lead to poor wash results. To avoid this
run a rinse programme after filling the salt container with special salt.
This will wash away salt water and any salt crystals that have been spilt.
Depending on the size of the salt grains, it can take several hours for
3
the salt to dissolve in the water and the special salt indicator
extinguish. The setting of the water softener and the consumption of
salt are dependent on the hardness of the local water.
Rinse aid
Rinse aid ensures that your dishes gleam and are free from spots, and
that your glasses are clear.
Rinse aid can be added in one of two ways:
• If you are using dishwasher detergent that already contains rinse aid,
the detergent including the rinse aid is put into the detergent compartment.
– In this case the dispensing of rinse aid from the supply container
must be deactivated to avoid a double dosage.
• If you are using dishwasher detergent and rinse aid separately, the
rinse aid is to be put into the rinse aid supply container.
– In this case the dispensing of rinse aid from the supply container
must be activated.
– The amount of rinse aid to be dispensed must be set.
J to
14
Use only branded rinse aid for dishwashers. Never fill the rinse aid con-
1
tainer with any another substance (e.g. concentrated vinegar) or dishwasher cleaning agent. This would damage the appliance.
Activating/deactivating the inflow of rinse aid
Some appliances are equipped with an additional 3in1 function.
3
If you use 3-in-1 dishwashing tablets and select the 3in1 function
together with the dishwashing cycle, the inflow of rinse aid does not
have to be deactivated (see ”3in1 function”).
Operating Instructions
1. Press the ON/OFF button.
The LED indicators for all programme buttons (and the button for the
delay start timer if present) light up. The LED indicators and any option
buttons that are present only light up if they are activated.
If the only LED indicator illuminated is one that belongs to a pro-
3
gramme button, this means that this dishwashing cycle has been activated. The dishwashing cycle must be deselected:
Press function buttons 2 and 3 simultaneously for approx. 1 second.
The LED indicators for all programme buttons (and the button for the
delay start timer if present) light up. The LED indicators and any option
buttons that are present only light up if they are activated.
2. Press function buttons 2 and 3 simultaneously and keep them pressed.
The LED indicators for function buttons 1 to 3 will flash.
3. Press function button 2.
The LED indicator for function button 2 will flash.
The
L indicator will indicate the current setting:
The L indicator will
become illuminated:
The L indicator is not illu-
minated:
Rinse aid inflow activated
(ex-factory setting)
Inflow of rinse aid is deactivated
4. Pressing function button 2 activates and deactivates the rinse aid dispensing function.
5. If the rinse aid dispensing function has been correctly set, press the
ON/OFF switch.
The setting of the rinse aid dispensing function is now saved.
15
Loading...
+ 33 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.