Electro-Harmonix Deluxe Memory Boy Instruction Manual

WARNING:

Your

Deluxe Memory Boy

comes equipped with

an Electro-Harmonix

9.6DC-200BI

power supply

(same as used by Boss™ & Ibanez™: 9.6 Volts DC 200mA). The Deluxe Memory Boy

requires 100mA at 9VDC with a plug that is center negative. The DXMB does not take batteries.

Using

the wrong adapter may damage your unit and void the warranty

DELUXE MEMORY BOY

Tap Tempo Analog Delay

Congratulations on your purchase of the Electro-Harmonix Deluxe Memory Boy, a true analog
delay with the ability to tap in the delay time. The Deluxe Memory Boy (DXMB) also includes two
types of delay time modulation, an effects loop in the feedback path of the delay block, an input
gain control, tap tempo divide and optional expression pedal control over four parameters:
Delay Time, Feedback, Modulation Depth and Modulation Rate. The DXMB is true bypass.

KNOBS

DELAY Knob – Sets the delay time from 34 mS to 700 mS. As you turn the DELAY knob

clockwise, the delay time will increase. If you tap in the delay time, using the TAP Footswitch,

the DELAY knob’s setting will be ignored until you move it again. If you turn the DELAY knob
after tapping in a delay time, the DELAY knob’s setting will supersede the last tap tempo that

was entered. Turning the DELAY knob, while listening to your echoes, will bend the pitch of your
notes. The DELAY knob can also be used to set the maximum delay time for expression pedal
control. N.B.: the TAP DIVIDE button functions have no effect on the DELAY knob; pressing this
button while the DELAY knob controls the delay time will not change the delay time.

FEEDBACK Knob – Controls the amount of signal that is circulated from the output of the
delay block to its input. Turning the FEEDBACK knob clockwise increases the number of echoes.
Setting the FEEDBACK control to its maximum clockwise position will cause the DXMB to run­away, or self-oscillate. If instead you only want to hear one echo for each of your notes, turn
the FEEDBACK knob down to its full counter-clockwise position. The FEEDBACK knob is also
used to set the maximum amount of feedback for expression pedal control.

DEPTH Knob – Sets the amount of triangle or square wave modulation that is applied to the
delay time. The DEPTH knob has a center detent which signifies the off position for no
modulation. Triangle wave modulation occupies the counter-clockwise half of the DEPTH knob,
square wave modulation the clockwise half of the DEPTH knob. As you turn DEPTH counter­clockwise from the center-detent’s off position, the amount of TRIANGLE wave modulation
increases, to its maximum setting at full counter-clockwise on the DEPTH knob. As you turn the
DEPTH knob clockwise from the center-detent position, the amount of square wave modulation
applied to the delay time increases, to its maximum setting at full clockwise on the DEPTH knob.

-CONTROLS and INDICATORS -

The DEPTH knob is also used to set the maximum amount of modulation for expression pedal
control.

RATE Knob – The RATE knob’s main function is to set the rate or speed of modulation. As you
turn the RATE knob clockwise the modulation rate will increase. The DEPTH knob must be set to
somewhere other than the off position to hear the RATE knob change modulation speed.
Additionally the RATE knob sets the maximum rate of modulation for expression pedal control.

The DXMB has a low cut tone control feature which the RATE knob adjusts. Enter low cut
mode by pressing and holding down the EXP. MODE button for 2 seconds. After two seconds, all
of the EXP. MODE LEDs will light solid and you can release the button. At this point, the RATE
knob no longer adjusts the rate of modulation but instead sets the frequency for the DXMB’s low
cut filter. As you turn RATE clockwise, less bass will be present in the delayed signal. To
completely bypass the low cut filter so that the full bass response comes through, turn the RATE
knob down to the full counter-clockwise position. To exit low cut mode, press and release the
EXP. MODE button. The DXMB will save the low cut setting, even after power cycling, and it will
remain at that setting until adjusted again. The default setting from the factory is for the low cut
filter to be bypassed.

GAIN Knob – Sets the input gain for the DXMB. As you turn the GAIN knob clockwise, the
input gain will increase. The total gain range is -6 dB to +20 dB. The gain block is the first stage
that the input signal goes through in the circuit. Both the dry and wet signals mixed by the
BLEND knob go through the gain block.

BLEND Knob – The BLEND knob is a wet/dry control allowing you to vary the mix between
direct and delayed signals at the OUTPUT jack of the DXMB. Set the BLEND knob to the full
clockwise position for an output that is 100% wet. Set the Blend knob to full counter-clockwise
for an output that is 100% dry. Setting BLEND anywhere in between will mix the wet and dry
signals together.

SWITCHES & LEDs

BYPASS Footswitch and STATUS LED – The BYPASS FSW is used to toggle the DXMB

between effect mode and true bypass mode. The red STATUS LED will light up when in effect
mode and turn off in bypass.

TAP Footswitch – The TAP FSW is used to tap in the delay time. Stomp on the TAP FSW two
times and the delay time will jump to the time between taps (if all the TAP DIVIDE LEDs are
off). If you tap more than twice, it will average the tap tempo for all taps. The DXMB will always
take into account the TAP DIVIDE setting when determining the delay time from the tap tempo.
For example, if your tap time is 1 second and the TAP DIVIDE setting is eighth notes, the actual
delay time is changed to 0.5 seconds. The maximum delay time, when tapped in, is 1.5
seconds; though at this delay time the effect will sound quite lo-fi. The DXMB will save
and recall the tap tempo when power cycling.

N.B.: The delay time for the DXMB is always set by the last method used. If you tap in a delay
time, the DELAY knob’s setting is ignored. After tapping in a delay time, if you turn the delay
knob, the tap time will be forgotten and replaced by the current position of the DELAY knob.

BEAT LED – The green BEAT LED always blinks at a rate that reflects the current delay time,
whether you used the TAP FSW or the DELAY knob to set the delay time. The BEAT LED will
also reflect the actual delay time rather than your tap time. For example, if your tap time is 900
mS but have the TAPE DIVIDE setting at eighth note triplet, the actual delay time is 300 mS so
the BEAT LED will blink every 300 mS. If you are modulating the delay time, the change in delay
time due to modulation will also be reflected in the BEAT LED.

TAP DIVIDE MODE

SYMBOL

DIVIDE RATIO

DELAY TIME (for a 600 mS TAP)

Quarter Note / OFF

1 / 1

600 mS

Dotted 8th Note

3 / 4

450 mS

Quarter Note Triplet

2 / 3

400 mS

8th Note

1 / 2

300 mS

8th Note Triplet

1 / 3

200 mS

16th Note

1 / 4

150 mS

TAP DIVIDE Button and LEDs – This button cycles through the six possible settings for TAP
DIVIDE. Each setting, except when all LEDS are off, will divide the tap tempo to create shorter
delay times in sync with your original tempo. It works like so: The DXMB always assumes that
the musician taps in a quarter note. That quarter note can then be divided down to five other
types of notes: dotted eighth note, quarter note triplet, eighth note, eighth note triplet and
sixteenth note. The sixth mode is quarter note or OFF, where the tap tempo is not divided down
and the delay time is set to your actual tap time. No LEDs are lit when Tap Divide is set to
quarter note/OFF. Below is a chart displaying the six available modes and how they divide down
the tap tempo to produce the actual delay time plus an example delay time setting:

N.B. The TAP DIVIDE button has no effect on the delay time when the delay is set by the
DELAY knob. Cycling through the different TAP DIVIDE modes, when the delay time was last set
by the DELAY knob, will not change the delay time in any way.

The TAP DIVIDE button setting is saved and recalled when power cycling.

TAP DIVIDE SEQUENCE MODE – The DXMB contains a little easter egg called Tap Divide
Sequence mode. In this mode, the DXMB will automatically cycle through the six tap divide
modes at a rate set by the RATE knob. To use this mode, do the following:

1. Tap in a delay time. Tap Divide Sequence mode will not work if the delay time is

set by the DELAY knob.

2. Press and hold the TAP DIVIDE button for 2 seconds. After 2 seconds, all of the

TAP DIVIDE LEDs will light up briefly, now you are in sequencer mode. You can
release the button.

3. Turn the RATE knob to change the speed of the sequence. You should see the

tap divide LEDs light up in a sequential fashion.

4. You can tap in new delay times to change the delay time range.

5. To exit Tap Divide Sequence mode: hold down the TAP DIVIDE button for

another 2 seconds. All 5 LEDs will light briefly to indicate you have exited
sequence mode. You could also simply turn the DELAY knob.

EXP. MODE Button and LEDs – The EXP. Mode button cycles through the five available
expression modes: RATE, DEPTH, FEEDBACK, DELAY and OFF. An expression pedal must be
plugged into the EXP. PEDAL jack to make use of these modes. When one of the LEDs of any of
the four modes is lit, the expression pedal will control that parameter. For example, if the RATE
LED is lit, the expression pedal controls the modulation rate, from slowest (expression pedal =

toe up), to the RATE knob’s current setting (expression pedal = toe down). The OFF setting

allows you to disable the expression pedal while it remains plugged into the DXMB. The setting
for the EXP. MODE is saved and recalled when power cycling.

LOW CUT MODE – The EXP. MODE button is also used to enter and exit low cut mode. Low
cut mode places a high pass filter after the bucket brigades in the delay section to remove bass
or low frequencies from the delayed signal. To enter low cut mode, press and hold the EXP.

MODE button for 2 seconds. All four Exp. Mode LEDs will light up indicating that you are in low
cut mode. Now you can release the button. Use the RATE knob to adjust the amount of bass
roll-off in the wet signal; as you turn RATE clockwise you will hear less bass. Turning the RATE
knob to full counter-clockwise completely bypasses low cut mode. The factory default setting
bypasses low cut mode. To exit low cut mode, press and release the EXP. MODE button, it will
return you to the previous expression mode setting while saving the new low cut setting. The
low cut mode setting is also saved and recalled when power cycling the DXMB.

LOW CUT MODE BYPASS – There are two ways to bypass low cut mode: 1) Enter low cut
mode by holding down the EXP. MODE button, then turn the RATE knob down to the full
counter-clockwise position. 2) While powering up the DXMB, hold down the EXP. MODE button.
It will immediately set the DXMB to bypass the low cut filter and also save the new setting. To
bypass low cut mode, you must press and hold the EXP. MODE button before applying power to
the DXMB.

I/O & POWER JACKS

EXPRESSION PEDAL CONTROL – The Deluxe Memory Boy allows external control over four

of its parameters: modulation RATE, modulation DEPTH, FEEDBACK and DELAY time. Please see
the EXP. PEDAL Jack section on the following page for suggestions on the type of expression
pedals to use. The pedal will need to have a TRS plug. You may also use a control voltage
between 0 V and 5 V.

Use the EXP. MODE button to choose the knob you want to control with an expression pedal;
repeatedly press and release the EXP. MODE button until the proper LED lights up. After
selecting a parameter, its associated knob will now set the maximum sweep range, which is the
toe down position for the expression pedal. For example, if you want to sweep the full range of
the FEEDBACK knob, you will need to set the FEEDBACK knob to its full clockwise position. The
expression pedal will then sweep from 0% feedback (toe up position) to 100% feedback (toe
down position).

Some expression pedals allow you to dial in the toe up position using an extra knob on the
pedal itself. When using this type of pedal you can set the range for both toe up (using the knob
on the pedal) and toe down (using the selected knob on the DXMB). If you use an expression
pedal that does not allow you to dial in the toe up position, then toe up will always be that
particular knob’s minimum setting.

The minimum setting for the RATE, FEEDBACK and DELAY knobs is the full counter clockwise

position. The minimum setting for the DEPTH knob is the center detent position at 12 o’clock. In

the case of the DEPTH knob, the expression pedal will always sweep from the 12 o’clock
position (toe up = depth off) to wherever the knob is set (toe down = maximum depth). So the
expression pedal will not sweep through both the Triangle and Square waves, but sweeps
through whichever side you have the DEPTH knob pointed to. For example, set the DEPTH knob

to 3 o’clock, approximately 50% square wave depth, and the expression pedal will sweep from

no depth (toe up) to 50% square wave depth (toe down).

EFFECTS LOOP – The Deluxe Memory Boy has an effects loop feature which allows other
effects to be inserted into the feedback loop of the delay block, before the bucket brigade chips.
This means that you can put additional effects on your wet signal without changing your dry
signal and each time your notes go around the feedback loop, they will also go through the
effects loop.

For example, if you connect a Micro POG in the DXMB’s effects loop, setting the Micro POG to
output only the upper octave, the delayed note will be one octave above the dry note that you