Elation TVL1000 User Instructions

TVL1000

TVL1000 General Information

Unpacking: Thank you for purchasing the TVL1000 by Elation Pro-

fessionals®. Every TVL1000 has been thoroughly tested and has been
shipped in perfect operating condition. Carefully check the shipping
carton for damage that may have occurred during shipping. If the

carton appears to be damaged, carefully inspect your xture for any

damage and be sure all equipment necessary to operate the unit has
arrived intact. In the event damage has been found or parts are miss­ing, please contact our toll free customer support number for further
instructions. Please do not return this unit to your dealer without con-

tacting customer support rst.

Introduction: The TVL1000 DMX intelligent LED fixture. The TVL1000

has 3 DMX Modes; Two 2 Channel Modes, and a 3 Channel Mode. The
fixture has two operating modes; manual mode or DMX controlled.
The TVL1000 can only be run as stand alone unit. This unit is suitable
for theaters, studios, retail stores, and other similar locations. For best

results use fog or special effects smoke to enhance the light projec­tions.

Customer Support: Elation Professionals® provides a toll free cus-

tomer support line, to provide help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.elationlighting.com for any com­ments or suggestions. Service Hours are Monday through Friday 8:00

a.m. to 4:30 p.m. Pacic Standard Time.

Voice: [phone]

Fax: [phone]

E-mail: [e-mail]
To purchase parts online visit http://parts.elationlighting.com

Rev. 2/13

User Instructions

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 2

TVL1000 General Instructions

TVL1000 Safety Precautions

To optimize the performance of this product, please read these
operating instructions carefully to familiarize yourself with the basic
operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please
keep this manual with the unit, for future reference.

TVL1000 Features

• 3 DMX Channel Modes; Two 2 Channel Modes & 3 Channel Mode

• 2 Operating Modes - Manual Mode & DMX Control

• Digital Display for Address and Function Setting

• Power Cord Daisy Chain

TVL1000 Warranty Registration

The TVL1000 carries a 2 year (730 days) limited warranty. Please fill
out the enclosed warranty card to validate your purchase and war­ranty. You may also register your product online at www.elationlight­ing.com. All returned service items whether under warranty or not,

must be freight pre-paid and accompany a return authorization (R.A.)

number. If the unit is under warranty you must provide a copy of your
proof of purchase invoice. Please contact Elation® customer support

for a R.A. number.

TVL1000 Handling Precautions

Caution! There are no user serviceable parts inside this unit. Do not

attempt any repairs yourself, doing so will void your manufactures war­ranty. In the unlikely event your unit may require service please contact
Elation Professionals®.

During operation the housing may become hot. Avoid touching the
unit with bare hands while in use.

Elation Professionals® will not accept any liability for any resulting dam-
ages caused by the non-observance of this manual or any unauthor-

ized modication to this unit.

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or re, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 18 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:
A. Objects have fallen, or liquid has been spilled into the appliance.
B. The appliance has been exposed to rain or water.
C. The appliance does not appear to operate normally or exhibits a

marked change in performance.

©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 4©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 3

TVL1000 Set Up

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

1

2

3

Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.

POWER

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

and PIN 3 (DMX +) of the last fixture.

TVL1000 Set Up

Power Supply: The Elation Professionals® TVL1000 contains an

electronic ballast, which will auto sense the voltage when it is plugged
into the power source. With the electronic ballast you do not need to

worry about wall voltage, this unit can be plugged in anywhere. Also

be sure to only use the included I.E.C. power cable supplied with the
unit.

DMX-512: DMX is short for Digital Multiplex. This is a universal pro-

tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX

controller sends DMX data instructions from the controller to the fix­ture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of
different manufactures to be linked together and operate from a sin­gle controller, as long as all xtures and the controller are DMX com­pliant. To ensure proper DMX data transmission, when using several

DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1

may be placed anywhere in a DMX line, at the beginning, at the end,

or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1

to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Master/Slave
Operation): The TVL1000 3 DMX channel modes. The DMX address

is set electronically using the controls on the side of the unit. Your unit
and your DMX controller require a approved DMX-

512 110 Ohm Data cable for data input and data
output. We recommend Accu-Cable DMX cables.

If you are making your own cables, be sure to use

standard 110-120 Ohm shielded cable (This cable

may be purchased at almost all professional sound
and lighting stores). Your cables should be made
with a male and female XLR connector on either

end of the cable. Also remember that DMX cable

must be daisy chained and cannot be split.

Figure 1

Notice: Be sure to follow gures two and three when making your own

cables. Do not use the ground lug on the XLR connector. Do not con-

nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding

the shield could cause a short circuit and erratic behavior.

COMMON

1

DMX512 IN

3

3-PIN XLR

2

Figure 2

XLR Pin Conguration

Pin 1 = Ground

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

Figure 4

XLR Male Socket

1 Ground

DMX512 OUT

3-PIN XLR

2 Cold

3 Hot

1

3

2

XLR Female Socket

2 Cold

DMX +

DMX -

1 Ground

3 Hot

Figure 3

Special Note: Line Termination.

When longer runs of cable are

used, you may need to use a terminator on the last unit to avoid erratic

behavior. A terminator is a 90-120 ohm 1/4 watt resistor which is con­nected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic

behavior.

Termination reduces signal errors and

1

avoids signal transmission problems

3

and interference. It is always advisable

2

to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)

©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 6©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 5

TVL1000 Set Up TVL1000 Control Panel

5-Pin XLR DMX Connectors.

Some manufactures use 5-pin XLR

connectors for DATA transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting stan­dard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be
used, these adaptors are readily available at most electric stores. The
chart below details a proper cable conversion.

3-Pin XLR to 5-Pin XLR Conversion

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

Pin 1

Pin 2

Pin 3

Pin 1

Pin 2

Pin 3

Pin 4 - Do Not Use

Pin 5 - Do Not Use

TVL1000 Installation

The TVL1000 is fully operational in three different mounting positions,
hanging upside-down from a ceiling, hanging sideways on truss-

ing, or set on a at level surface. The unit should be mounted using
a mounting clamp (not provided), afxing it to the mounting bracket
that is provided with the unit. Always ensure that the unit is rmly
xed to avoid vibration and slipping while operating. Always ensure

that the structure to which you are attaching the unit is secure and is

able to support a weight of 10 times the unit’s weight. Also, always

use a safety cable that can hold 12 times the weight of the unit when

installing the xture.

The equipment must be installed by a professional, and it must be

installed in a place where it is out of the reach of people’s grasp.

1 Display: To show the various menus and the selected functions

2 Indicator LED: First make sure to turn on the battery switch.

DMX On DMX input present

MASTER

SLAVE On Slave Mode

BATTERY On Battery is full

On Master Mode

Note: Connect the fixture to a main power supply. If the battery indicator
blinks slowly, it means the battery is being charged. When the indicator
stops blinking and stays lit, it means the battery is at full charge.

When using the battery power, the indicator light will not bet lit. If the
remaining battery power is less then 16%, the indicator will blink fast
reminding you that the battery is low and that it needs to be charged.

3 Button:

MENU To select the programming functions

DOWN

UP To go forward in the selected functions

ENTER To confirm the selected functions

4 Dimmer adjust knob: Adjust lightness for the unit from 0~100.

5 Color temperature adjustment: Adjust the color temperature from 3200k to 6500k,

6 DMX output: For DMX512 link, use 3/5-pin XLR plug cable to link the next unit.

7 DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal

8 Main input: Connect to main power supply.

9 Main output: Connect to the main power ofthe next unit.

⑩ Battery switch: Turn on or turn off the switch for battery mode. This switch can only

control battery.

To go backward in the selected functions

25K as a step.

©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 7 ©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 8

TVL1000 System Menu

TVL1000 System Menu

System Menu.

menu.

To access the main menu press the MENU button. Tap the UP or DOWN
buttons until you reach function you wish to change. When you reach
the function you wish to change press the ENTER button. When a
function is selected use the UP or DOWN buttons to change the func-

tion settings. Once your changes are made press the ENTER button,
and then press and hold the MENU button for at least three seconds
to conrm and lock the change into the system memory. If the MENU
button is not pressed and held within eight seconds the xture will
automatically conrm and lock the change into the system memory. To
exit without making any changes press the MENU button.

The TVL1000 comes with an easy to navigate system

ADDR - DMX Address Setting.

1. First set the unit to your desired DMX Channel mode.

2. To set your address, tap either the MENU, UP, or DOWN
buttons until “ADDR” is displayed, press ENTER. “1” will now be
displayed and ashing.

3. Press the UP or DOWN buttons to nd your desired address.
When you have found your desired DMX address press ENTER,

and connect your DMX Controller.

Battery state

CHND - This will let you switch between the 3 DMX Chan-

nel Modes.

1. Press the MENU button until “CHND” is displayed, press
ENTER. Either “MOD 1” (2 Channel Mode), “MOD 2” (2 Channel
Mode), or “MOD 3” (3 Channel Mode) will be displayed

2. Press the UP or DOWN buttons to choose your desired DMX
mode and press ENTER to conm and exit.

MANU - In this mode you can manually adjust the LED

intensity to create your desired color temperature.

©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 10©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 9

TVL1000 System Menu

TVL1000 System Menu

1. Press the MENU button until “MANU” is displayed, press
ENTER. “LED1”, “LED2” or “DINN” will be displayed. LED 1 is

warm white, LED 2 is cool white, and DIMM is the master
dimmer for this mode.

2. Use the UP or DOWN buttons to scroll to the color you
would like adjust rst, and press ENTER.

3. Use the UP or DOWN buttons to adjust the intensity of the
chosen color, and press ENTER after the adjustment.

4. Continue to make adjustments to the two colors until your
desired color is reached. Once your desired color is reached do

not leave this mode.

5. To leave this mode, press the MENU button. Once you leave

this mode, all settings will be reset.

DNST - This mode can be used as a precaution mode, that

in case the DMX signal is lost, the operating mode chosen

in the setup is the running mode the xture will go into when

the DMX signal is lost. You can also set this as the operat-

ing mode you would like the unit to return to when power is

applied.

1. Press the MENU button until “DNST” is displayed, press ENTER.

2. Either “MASL”, “BLND”, or “LAST” will be displayed. Choose an

operating mode you would like the unit to start up in when power
is applied or the DMX signal is lost.

• MASL (Master Slave) - If the DMX signal is lost or power is
applied, the unit will automatically go into Master Slave mode.

• BLND (Blackout) - If the DMX signal is lost or power is applied,

the unit will automatically go into stand by mode.

• LAST (Last State) - If the DMX signal is lost the xture will stay in

the last DMX set up. If power is applied and this mode is set, the
unit will automatically go into the last DMX set up.

©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 11

3. Press ENTER to conrm your desired set up.

LED - With this function you can have the LED display

turn off after 20 seconds.

1. Press the MENU button until “LED” is displayed, press
ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display On at all
times, or “OFF” so that the LED display turns off after 20 sec-

onds.

3. Press ENTER to conrm.

DISP - This function will reverse the display 180º.

1. Press the MENU button until “DISP” is displayed, press
ENTER.

2. Press the UP button to select “DSIP” to activate this function,
or “DISP” to deactivate this function.

3. Press ENTER to conrm.

BATT - This function is used for battery charging.

1. Press the MENU button until “BATT” is displayed, press
ENTER.

2. Either “CHAR”, “LOAD”, or “STAT” will be displayed. Use the
UP or DOWN buttons to scroll through the functions, and press
ENTER to select your desired function.

• CHAR (Charging) - When this is selected you are able to charge

or stop charging the battery. When a power cable is connected

and “ON” is selected, the battery is now being charged. To stop
charging, select “OFF”.

• LOAD (LED On or OFF) - This will let you blackout the LED while

©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 12

TVL1000 Universal DMX Control TVL1000 System Menu

charging. Select “OFF” to blackout the LED or “ON” to stop the

LED blackout.

• STAT (Charge Status) - This will let you check the battery status.

3. Press ENTER to conrm your setting and exit.

TEST - This function will run a self test program.

1. Tap the MENU button until “TEST” is displayed, press ENTER.

2. The xture will now run a self test program. To stop the self
test press either the MENU or ENTER button.

FHRS - With this function you can display the running time

of the unit.

1. Press the MENU button until “FHRS” is displayed, press
ENTER.

2. The display shows the running time of the unit. Press MENU
to exit.

VER - Use this function to display the Software version of

the unit.

Universal DMX Control: This function allows you to use a Elation®

universal DMX-512 controller to create unique programs tailored to
your individual needs.

1. The TVL1000 has three DMX channel modes. To set the chan-

nel mode see page 10. See page 15 for the DMX modes & traits.

2. To control your fixture in DMX mode, follow the set-up procedures

on pages 5-7 as well as the set-up specifications that are
included with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instructions on page 10 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on
the last fixture.

7. For help operating in DMX mode consult the manual included
with your DMX controller.

Manual Mode: This mode allows the user to adjust the color intensity

to create their own desired color temperature.

1. Press the MENU button until “MANU” is displayed, and press

ENTER.

2. Follow the instructions on pages 10-11 to operate this mode.

3. You can also use the Color Adjust Knob and Dimmer Knob to

manually create your desired color temperature. Please see the
Control Panel on page 8.

1. Press the MENU button until “VER” is displayed, press
ENTER.

2. The display will show the software version.

©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 13 ©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 14

TVL1000 DMX Modes

TVL1000 Photometric Chart

TVL1000 Power Cord Daisy Chain

Powered via power outlet: With this feature you can connect the

xtures to one another using the IEC input and output sockets.
The quantity that can be connected is 12 fixtures maximum.
After 12 xtures you will need to use a new power outlet. They
must be the same xtures. DO NOT mix xtures.

Powered via battery power: With this feature you can connect

the xtures to one another using the IEC input and output sock­ets. The quantity that can be connected is 5 xtures maximum.
After 5 xtures you will need to use a new power outlet. They
must be the same xtures. DO NOT mix xtures.

NOTE: Powered via battery does not mean that 5 xtures are

being powered by one battyer, each unit must have a battery

connected.

©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 15 ©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 16

TVL1000 Battery Installation

TVL1000 Fuse Replacement

The TVL1000 can also be powered by battery; Part# TVL-

1000Bat (not included ). Connecting the battery is a very simple

procedure. Follow the instructions below to connect the battery.

1. Start by unscrewing and
removing the thumb screws
that hold the panel in place.

2. Once the panel has been

removed, connect the battery to
the battery wire located inside
the unit.

First unplug the power. Locate and remove the unit’s power cord.

Once the cord has been removed located the fuse holder located

inside the power socket. Insert a flat-head screw driver into the power
socket and gently pry out the fuse holder. Remove the bad fuse and
replace with a new one. The fuse holder has a built-in socket for a
spare fuse be sure not to confuse the spare fuse with active fuse.

TVL1000 Cleaning

Fixture Cleaning: Due to fog residue, smoke, and dust cleaning

the internal and external optical lenses and mirror should be carried

out periodically to optimize light output. Cleaning frequency depends

on the environment in which the fixture operates (I.e. smoke, fog

residue, dust, dew). In heavy club use we recommend cleaning on a
monthly basis. Periodic cleaning will ensure longevity, and crisp out­put.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

2. Use a brush to wipe down the cooling vents and fan grill.

3. Clean the external optics and mirror with glass cleaner and a soft

cloth every 20 days.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the unit

back in.

TVL1000 Trouble Shooting

3. When the battery has been
connected simply slide the
battery into the compart­ment, and secure using the
pop up thumb screws.

©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 17

Listed below are a few common problems that you may encounter,
with solutions.

No light output from the unit;

1. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.

2. Be sure the fuse holder is completely and properly seated.

©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 18

TVL1000 Warranty

TVL1000 Specifications

2-YEAR LIMITED WARRANTY

A. Elation® Architectural hereby warrants, to the original purchaser, Elation®
Professionals® products to be free of manufacturing defects in material and
workmanship for a period of two years (730 days) from the date of purchase. This
warranty shall be valid only if the product is purchased within the United States

of America, including possessions and territories. It is the owner’s responsibility

to establish the date and place of purchase by acceptable evidence, at the time
service is sought.

B. For warranty service, send the product only to the Elation® Professionals®
factory. All shipping charges must be pre-paid. If the requested repairs or ser­vice (including parts replacement) are within the terms of this warranty, Ela­tion® Professionals® will pay return shipping charges only to a designated point
within the United States. If the entire instrument is sent, it must be shipped in
its original package. No accessories should be shipped with the product. If any
accessories are shipped with the product, Elation® Professionals® shall have no
liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the

product is modied in any manner which Elation® Professionals® concludes,

after inspection, affects the reliability of the product; if the product has been
repaired or serviced by anyone other than the Elation® Professionals® factory
unless prior written authorization was issued to purchaser by Elation® Profes­sionals®; if the product is damaged because not properly maintained as set forth
in the instruction manual.

D. This is not a service contract, and this warranty does not include mainte­nance, cleaning or periodic check-up. During the period specied above, Ela­tion® Professionals® will replace defective parts at its expense, and will absorb
all expenses for warranty service and repair labor by reason of defects in mate­rial or workmanship. The sole responsibility of Elation® Professionals® under
this warranty shall be limited to the repair of the product, or replacement thereof,
including parts, at the sole discretion of Elation® Professionals®. All products
covered by this warranty were manufactured after January 1, 1990, and bear
identifying marks to that effect.

E. Elation® Professionals® reserves the right to make changes in design and/or
improvements upon its products without any obligation to include these changes
in any products theretofore manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to
any accessory supplied with products described above. Except to the extent
prohibited by applicable law, all implied warranties made by Elation® Profession­als® in connection with this product, including warranties of merchantability or
tness, are limited in duration to the warranty period set forth above. And no war­ranties, whether expressed or implied, including warranties of merchantability or

tness, shall apply to this product after said period has expired. The consumer’s
and or Dealer’s sole remedy shall be such repair or replacement as is expressly

provided above; and under no circumstances shall Elation® Professionals® be
liable for any loss or damage, direct or consequential, arising out of the use of,
or inability to use, this product.

G. This warranty is the only written warranty applicable to Elation® Profession­als® Products and supersedes all prior warranties and written descriptions of
warranty terms and conditions heretofore published.

©Elation Professionals® - www.elationlighting.com - TVL1000 Instruction Manual Page 19

Model: TVL1000

Voltage: 100 - 240V~50/60Hz

LEDs: 400 LEDs (200 Cool White &

200 Warm White)

Power Consumption: 26W
Fuse: 7A

Power Cord Daisy Chain: 12 Fixtures Max.
Dimensions: 15.9”(L) x 13.7”(W) x 4.4”(H)

406mm x 350mm x 113mm

Weight: 13.6 Lbs. / 6.2 kgs.
Colors: Cool White & Warm White

Duty Cycle: None
DMX: 3 DMX Channel Modes: 2 Channel

Mode, 2 Channel Mode, & 3 Channel

Mode

Sound Active: Ye s
Working Position: Any Safe, Secure Position
Warranty: 2 Year (730 days)

Please Note: Specications and improvements in the design

of this unit and this manual are subject to change without any
prior written notice.

Auto Sensing Voltage: This xture contains a electronic bal-

last, which will auto sense the voltage when it is plugged into the
power source.

©Elation Professionals®

A Division of the AmericanDJ® Group of Companies

World Headquarters:

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: [phone] Fax: [phone]

Web: www.elationlighting.com E-mail: [e-mail]

American DJ Europe

Junostraat 2

6468 EW Kerkrade

Netherlands

[e-mail] / www.americandj.eu

Tel: [phone] / Fax: [phone]