Elation POWER SPOT 700CMY User Manual

Revised 4/4/2007 visage

POWER SPOT 700CMY

User Manual

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 2

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 3

Table of Contents

Introduction...........................................................................................................................4

Unpacking ....................................................................................................................4

Customer Support ......................................................................................................4

Discharge Lamp Precautions ..................................................................................5

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 4

INTRODUCTION: Congratulations, you have just purchased one of the most innovative

and reliable lighting fixtures on the market today! The Power Spot 700CMY™, has been

designed to perform reliably for years when the guidelines in this booklet are followed.

Please read and understand the instructions in this manual carefully and thoroughly

before attempting to operate this unit. These instructions contain important information

regarding safety during use and maintenance.

UNPACKING: Thank you for purchasing the Power Spot 700CMY™ by Elation

Professional®. Every Power Spot 700CMY™ has been thoroughly tested and has been

shipped in perfect operating condition. Carefully check the shipping carton for damage

that may have occurred during shipping. If the carton appears to be damaged, carefully

inspect your unit for damage and be sure all accessories necessary to operate the unit

have arrived intact. In the event damage has been found or parts are missing, please

contact our customer support team for further instructions. Please do not return this unit

to your dealer without first contacting customer support at the number listed below.

CUSTOMER SUPPORT: Elation Professional® provides a customer support line, to

provide set up help and to answer any question should you encounter problems during

your set up or initial operation. You may also visit us on the web at

www.elationlighting.com for any comments or suggestions. For service related issue

please contact Elation Professional®. Service Hours are Monday through Friday 9:00

a.m. to 5:00 p.m. Pacific Standard Time.

Voice: [phone]

Fax: [phone]

E-mail: [e-mail]

Forum: www.ElationLighting.com/forum/

Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit

to rain or moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs

yourself, doing so will void your manufactures warranty.

Please do not discard the shipping carton in the trash. Please recycle whenever

possible.

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 5

WARRANTY REGISTRATION: The Power Spot 700CMY™ carries a two year (730 days)

limited warranty. Please fill out the enclosed warranty card to validate your purchase. All

returned service items whether under warranty or not, must be freight pre-paid and

accompany a return authorization (R.A.) number. The R.A. number must be clearly

written on the outside of the return package. A brief description of the problem as well as

the R.A. number must also be written down on a piece of paper and included in the

shipping container. If the unit is under warranty, you must provide a copy of your proof of

purchase invoice. Items returned without a R.A. number clearly marked on the outside of

the package will be refused and returned at cutomers exspence. You may obtain a R.A.

number by contacting customer support at [phone].

DISCHARGE LAMP WARNING: This fixture is fitted with a discharge

lamp, which is highly susceptible to damage if improperly handled.

Never touch the lamp with your bare hands, as the oil from your

hands will shorten lamp life. Also, never move the fixture until the

lamps have had ample time to cool. Remember, lamps are not

covered under warranty conditions.

This fixture emits intense UV radiation, which is harmful to the eyes and skin. The

intense luminance of the lamp can cause severe damage to the retina. Never operate

this fixture with the protective covers removed, these covers have been specially

designed to shield against UV radiation.

Epileptic Warning: Those suffering from epilepsy should avoid looking directly into the

lamp at all times.

Avoid switching the fixture on and off repeatedly in short intervals, as this will reduce

lamp life and intensity.

To achieve the intensity associated with discharge lamps, these lamps use a gas

sealed in a high-pressure environment to emit a brilliant output. Due to the high

pressure involved with the construction of the lamp, the lamp may explode during

prolonged extensive use. This risk is increased with age; added care is encouraged

when dealing with older lamps. Thus, lamp should always be replaced at the end of

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 6

their recommended duty cycle. Extreme caution should be used when operated this or

any fixture fitted with a gas discharge lamp.

Never open this fixture while in use!

During the initial operation of this fixture, a light smoke or smell may emit from the
interior of the fixture. This is a normal process and is caused by excess paint in the
interior of the casing burning off from the heat associated with the lamp.

This device falls under protection-class 1. Therefore it is essential that the device be
grounded properly.

All electrical connections must performed by qualified personal.

Be sure the available voltage matches the voltage requirements of the unit.

Be sure the power cord is never crimped or damaged. If the power cord is damaged,
replace it immediately with a new one of similar power rating.

Always disconnect from main power before performing any type of service or any
cleaning procedure.

Only handle the power cord by the plug. Never pull out the plug by tugging the wire
portion of the cord.

Please be aware that damages caused by modifications to the device are not subject
to warranty.

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 7

2. SAFETY INSTRUCTIONS

The Power Spot 700CMY™ is an extremely sophisticated piece
of electronic equipment. To guarantee a smooth operation, it is
important to follow the guidelines in this manual. The
manufacturer of this device will not accept responsibility for
damages resulting from the misuse of this fixture due to the
disregard of the information printed in this manual.

1. Always be sure that the fan and the air inlets remain clean and are never

blocked. Allow about 6” (15cm) between this fixture and other devices or a wall

to allow for proper cooling.

2. Never touch the fixture during normal operation. This can cause severe

personal injuries and/or damage to the fixture.

3. Be sure to unplug the POWER SPOT 700CMY™ from the power outlet before

performing any service related issues.

4. Lamp Replacement; Allow at least 30 minutes after disconnecting main power

before you open the POWER SPOT 700CMY™. To prevent personal injury,

never touch the lamp if you are not absolutely sure it has cooled.

5. Never look directly into the lamp beam. You risk injury to your retina, which may

induce blindness.

6. Be sure to track and record the lamp running time. The lamp should be

changed at the end of the specified lamp life, regardless of lamp output. You

may also have to change the lamp if it shows any deformations or damage.

The same is with all glass components, color filters, lenses and mirrors.

7. For safe operation, follow the Installation guide described in chapter two of this

manual. Operating the POWER SPOT 700CMY™ without suited safety aids

such as safety cables or clamps can increase the risk of damage and/or

personal injury.

8. Installation should only be performed by qualified and certified personal.

9. When mounting this fixture, use only the original rigging parts included with this

fixture. Any structural modification will void the original manufactures warranty

and may increase the risk of damage and/or personal injury.

10. To reduce the risk of fire or shock, do not expose this unit to rain or moisture.

11. Do not attempt to operate this fixture if the power cord is frayed or damaged.

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 8

3. FEATURES

• Pan 530° / Tilt 280°

• 3 operation mode: DMX controlled, stand alone or sound activated

• Electronic Power Supply

• Control board with 4-digit display

• Digital display can be turned 180° to fit different installation position

• CMY Subtractive Color Mixing

• Additional Color Wheel: 8 User replacable colors

• 2 Gobo Wheels:

o Fixed: 9 plus open

o Rotating: 7 Suer replaceable plus open

• Auto test for all functions

• Automatic Pan/Tilt Correction

• Glass Dichroic Reflector for Even Lamp Output

• Anti-Reflective Coated Lenses

• Brilliant MSR700/2 Lamp (700w, 1000Hrs, 7200K)

• USITT DMX-512 Complaint

• Value of each DMX-channel can be displayed

• Uses 24 DMX Channels (16-bit mode)

• Variable Frost Filter

• Variable Color Correction Filter

• 3-Facet Prism

• Variable Animation Wheel

• User Replaceable Color and Gobos

• Intergrated Tilt Lock System

• Modular Construction

• Variable Zoom: 14˚~32˚ (Beam Angle)

• Motor Driven Focus

• Variable Iris (4%~100%)

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 9

4. GENERAL GUIDELINES

This fixture is a professional lighting effect designed for use on stage, in nightclubs, in

theatres, etc. Do not attempt operation or installation without a proper knowledge on how

to so.

This fixture was designed for indoor use only.

Consistent operational breaks may ensure that the fixture will function properly for many

years to come.

Do not shake the fixture around. Avoid brute force when installing or operating the device.

While choosing an installation location, please be sure that the fixture will not be

exposed to extreme heat, moisture or dust. The minimum distance between the fixture

and a wall or flat surface should be at least .5 meter (about 1.5ft).

Always install the fixture with an appropriate safety cable. When installing the fixture in a

suspended environment always be to use mounting hardware no less than M10 x 25

mm, also be sure the hardware is insert in the pre-arranged screw holes in the base of

the fixture.

When using the quick release “Omega” cam-lock system, be sure the four quick lock

fasteners are locked in the quick lock holes correctly, see page 16 for more information

on the proper mounting procedures.

Do not attempt to operate this fixture until you have familiarized yourself with its functions.

Do not permit operation by persons not qualified for operating this type of theatrical

fixture; most damages are the result of operation by person unfamiliar with the operation

of this type of fixture.

If service is ever required, please use the original packaging to transport the fixture in for

service.

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 10

Transportation and Handling

The POWER SPOT 700CMY™ comes with two carrying handles built into the base.

Always transport the fixture by these handles. Never lift or carry the POWER SPOT

700CMY™ by the yoke (head assembly) this can seriously damage the unit and will void

your manufactures warranty.

Connections

Power supply:

Electronic ballast with:

90~260 Volts, 50~60 Hz,

Grounded contact type plug – Neutrik Powercon

Connected load 1000W <=> 4.5 A (blind current compensation).

NOTE: The universal power supply will accept any voltage source as detailed

above without any type of internal or user modifications.

DMX:

USITT DMX 512 Standard input/output, 3 pole connectors.

[+] = Pin 3 / [-] = Pin 2 / [Ground] = Pin 1

Fuse Requirements:

The POWER SPOT 700CMY’s electronic and lamp systems are protected by two

GMA (5x20mm) external fuses:

Lamp: 250v/10A (120v Operation) or 250v/5A (220v Operation)

Electronics: 250v/2A (120v Operation) or 250v/1A (220v Operation)

The fuse requirements are clearly printed on the side of the fixture.

• Always disconnect main power before changing the fuse!

• Always replace with the exact same type fuse unless otherwise specified by

an authorized Elation® service technician. Replacing with anything other

than the specified fuse can severely damage your fixture and will void your

manufactures warranty.

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 11

5. FIXTURE LAYOUT

1. Moving Head

2. Carrying Handles

3. LED Menu Display

4. Head Tilt Lock

5. Omega Clamp

6. Software-Update

Connector

7. Microphone

Sensitivity

8. DMX- Input

9. DMX- Output

10. Fan (air inlet/outlet)

11. Electronics Fuse

12. Main Power Supply

(Powercon)

13. Power On/Off

14. Lamp Fuse

MaxMin

DMX IN DMX OUT

Software Update

1.Ground

2.Data -

3.Data +

Mic Sensitivity

6

7

8 9

10

15

POWER

Power Input: 90 - 260 VAC, 50/60 Hz

Lamp
Fuse

Electronic

Fuse

10

11

12

13 14

15

T

2

A

@

11

5

V~

T

1

A

@

2

3

0

V

~

T

1

0

A

@

1

1

5

V

~

T

5A

@

2

3

0

V

~

0

1

2

2

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 12

15. 4-Segment LED

Menu Display

16. Mode Button

17. Enter Button

18. Up Button

19. Down Button

Side View - Menu and Display

1. Head Assembly – The head assembly consist of the main output lens, and
either the standard or CMY control module.

2. Carrying Handle – The fixtures includes two built-in carrying handles. Be sure to
always handle the fixture by the built-in carrying handles. Never lift or carry the
fixture by the head or retaining arms as this could cause serious damage to the
fixture and void your manufactures warranty.

3. 4-Segment Menu Display – This display details all the various menu functions.
See page XX for a detailed breakdown of the operating menu.

4. Tilt Lock – This lock will hold the head assembly in place for transportation
and/or service. Depress the lock button to lock and unlock the head assembly.
The head will lock in a 90˚ or 45˚ orientation. Always be sure to unlock the head
assembly before applying main power to the unit. Failure to do so will result in a
start-up error and may damage the unit.

5. Omega Clamp - This fixture uses a cam-lock clamp system that allows a quick
and efficient means to secure a clamp to the unit. To attach a clamp to the unit,

15

161718

19

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 13

attach a clamp that is rated to handle the weight of the unit to your omega
clamp. After a clamp has been attached to the omega clamp, attach the cam
locks to the designated position on the bottom of your unit. Lock the cam locks
into position by turning the wing nuts 90°. See page XX for proper clamp
mounting and assembly.

6. Firmware Connection – This connector is for use by an authorized technician
only. This connector is used to upgrade the operating software and to test the
fixture.

7. Microphone Sensitivity Adjustment Knob – This knob is used to adjust the
frequency sensitivity of the internal microphone when operating in “audio”
mode. When the knob is turned counter-clockwise the unit is less sensitive to
sound. When the knob is turned clockwise the unit is more sensitive sound.

8. DMX Input Jack – This 3-Pin XLR jack is used to receive an incoming DMX
signal.

9. DMX Output Jack – This 3-Pin XLR jack is used to send an outgoing DMX
signal. For best results this jack should be terminated if it is the last fixture in a
DMX daisy-chain (see termination on page 14).

10. Internal Cooling Fan – This fixture is equipped with two high-velocity variable
speed fans mounted in the base to aid in the cooling process. These fans are
designed to vary their velocity at different operating temperatures. When the
fixture reaches a predetermined internal operating temperature the fans
function at high speeds. The higher speeds provide better cooling associated
with higher operating temperatures during long use. When the fixture is
operating at a lower temperature the fans operate at low speed. Be sure to keep
all vents clean, blocked cooling vents can shorten lamp life and reduce the
fixtures reliability. For more information on the fan functions see page 23,
section 3.9.7.

11. Electronics Fuse Holder – This housing holds a 250v/2A GMA fuse (120v
operation). Never defeat this fuse, this fuse is designed to protect the
electronics in the event of severer power fluctuations. In the event of fuse failure,
always be sure to replace this fuse with an exact match unless otherwise
instructed by an authorized Elation technician.

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 14

12. Powercon Connector – This power jack is designed to be used only with the
Neutrik Powercon adapter included with your fixture. This jack provides main
power to your fixture.

13. Power Switch – The switch is used to control main power to fixture’s
electronics.

14. Lamp Fuse Holder – This housing holds a 250v/10A GMA fuse (120v operation).
Never defeat this fuse. This fuse is designed to protect the lamp in the event of
severer power fluctuations. In the event of fuse failure, always be sure to replace
this fuse with an exact match unless otherwise instructed by an authorized
Elation technician.

15. 4-Segment Menu Display – This display details menu functions.

16. Mode Select Button – This button is used to access the fixture’s main system
menu and on-board programming functions.

17. Enter Select Button – This button is used to select and confirm a menu function
when working in the fixture’s operating system.

18. Down Select Button – This button is used to scroll backwards when navigating
through the system menu.

19. Up Select Button - This button is used to scroll forward when navigating through
the system menu.

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 15

6. MOUNTING AND INSTALLATION

MOUNTING

The POWER SPOT 700CMY™ is fully operational in two different mounting

positions, hanging upside from a ceiling or set on a flat level surface. To avoid

internal damage to the unit, never mount the unit on its side as illustrated

below. Be sure this fixture is kept at least 0.5m away from any flammable

materials (decoration etc.). Install a safety cable that can hold at least 10 times

the weight of the fixture. Never use the carrying handles for secondary

attachment.

Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE
0711-217 for proper installation in Europe
To ensure proper installation, only qualified staff should attempt
installation.

Mounting points

Overhead mounting requires extensive experience, including amongst others calculating

working load limits, a fine knowledge of the installation material being used, and

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 16

periodic safety inspection of all installation material and the fixture. If you lack these

qualifications, do not attempt the installation yourself. Improper installation can result in

bodily injury.

CAUTION!
Be sure a qualified electrician performs all electrical
connections.

Be sure to complete all rigging and installation procedures before connecting the main
power cord to the appropriate wall outlet.

Clamps

The POWER SPOT 700CMY™ has been designed to hold multiple clamps to the bottom

of the unit in several different orientations. Always use an appropriately rated clamp to

mount this unit to truss. Refer to the printed instructions on the bottom of the fixture for

proper clamp installation.

a) Cam lock System: This system allows a quick and efficient means to

secure a clamp to the unit. To attach a clamp to the unit, attach a clamp

that is rated to handle the weight of the unit to your cam lock. After a

clamp has been attached to the cam lock, attach the cam locks to the

designated position on the bottom of your unit. Lock the cam locks into

position by turning the wing nuts 90°.

90°

b) Be sure to always use two cam locks mounted to the bottom of unit to

ensure safe truss mounting (each two opposite threads max. M10x20).

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 17

Secure the POWER SPOT 700CMY™

Regardless of the rigging option you choose for your POWER SPOT 700CMY™ always

be sure to secure your fixture with a safety cable. The fixture provides a built-in rigging

point for a safety cable on the underside of the fixture, be sure to use this point and never

secure a safety cable to a carrying handle.

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 18

7. UNDERSTANDING DMX

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most

lighting and controller manufactures as a form of communication between intelligent

fixtures and controllers. A DMX controller sends DMX data instructions from the controller

to the fixture. DMX data is sent out as serial data that travels from fixture to fixture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers

only have a DATA “OUT” terminals). DMX Linking: DMX is a language allowing all makes

and models of different manufactures to be linked together and operate from a single

controller, as long as all fixtures and the controller are DMX compliant. To ensure proper

DMX data transmission, when using several DMX fixtures try to use the shortest cable

path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may

be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the

middle. Therefore, the first fixture controlled by the controller could be the last fixture in

the chain. When a fixture is assigned a DMX address of 1, the DMX controller knows to

send DATA assigned to address 1 to that fixture, no matter where it is located in the DMX

chain.

Data Cable (DM X Cable) Requirements (For DMX and Master/Slave Operation): The

POWER SPOT 700CMY™ can be controlled via DMX-512 protocol. The POWER SPOT

700CMY™ is a 24 channel DMX fixture. The DMX address is set electronically using the

controls on the side panel of the fixture. Your fixture and your DMX controller require a

standard 3-pin XLR connector for data input and data output (Figure Below). If you are

making your own cables, be sure to use standard two conductor shielded cable (This

cable may be purchased from your Elation dealer or at most professional lighting

retailers). Your cables should be made with a male and female XLR connector on either

end of the cable. Also, remember that DMX cable m us t be dais y chained and can not be

split.

Power Spot 700CMY™

©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 19

Notice: Be sure to follow the figure on the previous page when making your own

cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s

shield conductor to the ground lug or allow the shield conductor to come in contact

with the XLR’s outer casing. Grounding the shield could cause a short circuit and

erratic behavior.

DMX-512 control connection

Connect the provided XLR cable to the female 3-pin XLR output of your controller and the

other side to the male 3-pin XLR input of the moving head (Please refer to the diagram

below.). You can chain multiple moving heads together through serial linking. The cable

needed should be two conductor, shielded cable with XLR input and output connectors.

Always be sure daisy chain your in and out data connections, never split or “Y” your DMX

connections unless you are using an approved DMX splitter such as the Elation Opto

Branch 4™ or DMX Branch/4™.

Special Note: Line Termination. When longer runs of cable are used, you may need

to use a terminator on the last fixture to avoid erratic behavior. A terminator is a 90-120

ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR

connector (DATA + and DATA -). This fixture is inserted in the female XLR connector of

the last fixture in your daisy chain to terminate the line. Using a cable terminator

(Elation part number Z-DMX/T) will decrease the possibilities of erratic behavior.