Elation Pixel Driver 4000 Users Manual

PIXEL DRIVER 4000™

user manual

©2018 ELATION PROFESSIONAL all rights reserved. Information, specifications,

Date

Document

Version

Software

Version ≥

Notes

05/24/18

1

1.0

Initial release.

11/28/18

1.2

N/C

Updated release.

diagrams, images, and instructions herein are subject to change without notice. ELATION
PROFESSIONAL logo and identifying product names and numbers herein are trademarks
of ELATION PROFESSIONAL. Copyright protection claimed includes all forms and matters
of copyrightable materials and information now allowed by statutory or judicial law or
hereinafter granted. Product names used in this document may be trademarks or
registered trademarks of their respective companies and are hereby acknowledged. All
non-ELATION brands and product names are trademarks or registered trademarks of their
respective companies.

ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all
liabilities for property, equipment, building, and electrical damages, injuries to any persons,
and direct or indirect economic loss associated with the use or reliance of any information
contained within this document, and/or as a result of the improper, unsafe, insufficient and
negligent assembly, installation, rigging, and operation of this product.

Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040

323-582-3322 | 323-832-9142 fax | www.elationlighting.com | [e-mail]

Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands

[phone] | [phone] fax | www.elationlighting.eu | [e-mail]

Elation Professional Mexico | AV Santa Ana 30 | Parque Industrial Lerma, Lerma, Mexico 52000

[phone]

DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated
version of this document may be available online.
Please check www.elationlighting.com for the latest revision/update of this
manual, before beginning installation and/or programming.

2

CONTENTS

General Information

4

Limited Warranty (USA Only)

5

Safety Guidelines

7

Maintenance Guidelines

8

Device Overview

9

Installation Guidelines

10

Connections and Cables

12

System Configuration

13

System Menu

15

Specifications

18

Optional Accessories

19

3

GENERAL INFORMATION

INTRODUCTION

This fixture has been designed to perform reliably for years when the information in this
manual are followed. Please read and understand all the instructions and guidelines
carefully and thoroughly before operating this unit. This manual contains important
information regarding safety, installation, use, and maintenance.

UNPACKING

Each fixture has been thoroughly tested and shipped in perfect operating condition.
Carefully check the outer shipping carton for signs of any damage that may have occurred
during shipping. If the outer carton appears to be damaged, carefully inspect the fixture for
damage and be sure all included accessories have arrived intact. In the event damage has
been found and/or parts are missing, please contact our customer support team for further
instructions. Please do NOT return this fixture to your dealer without first contacting
customer support at the number listed below. Please do NOT discard the outer shipping
carton in the trash. Please recycle whenever possible.

CUSTOMER SUPPORT

Contact ELATION Service for any product related service and support needs.
Also visit forums.elationlighting.com with questions, comments or suggestions.

ELATION SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
323-582-3322 | Fax [phone] | [e-mail]

ELATION SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
[phone] | Fax [phone] | [e-mail]

REPLACEMENT PARTS please visit parts.elationlighting.com

IMPORTANT NOTICE!

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.
DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID YOUR
MANUFACTURES WARRANTY. D A M A G E S R E S U L T I N G FROM MODIFICATIONS TO
THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND
GUIDELINES IN THIS MANUAL VOID THE MANUFACTURES WARRANTY AND ARE
NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.

4

LIMITED WARRANTY (USA ONLY)

A. Elation Professional hereby warrants, to the original purchaser, Elation Professional products to be free of
manufacturing defects in material and workmanship for a period of two years (730 days), and Elation
Professional product rechargeable batteries to be free of manufacturing defects in material and workmanship for
a period of six months (180 days), from the original date of purchase. This warranty excludes discharge lamps
and all product accessories. This warranty shall be valid only if the product is purchased within the United
States of America, including possessions and territories. It is the owner’s responsibility to establish the date and
place of purchase by acceptable evidence, at the time service is sought. B. For warranty service, send the
product only to the Elation Professional factory. All shipping charges must be pre-paid. If the requested repairs
or service (including parts replacement) are within the terms of this warranty, Elation Professional will pay return
shipping charges only to a designated point within the United States. If any product is sent, it must be shipped
in its original package and packaging material. No accessories should be shipped with the product. If any
accessories are shipped with the product, Elation Professional shall have no liability what so ever for loss and/or
or damage to any such accessories, nor for the safe return thereof. C. This warranty is void if the product serial
number and/or labels are altered or removed; if the product is modified in any manner which Elation Professional
concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by
anyone other than the Elation Professional factory unless prior written authorization was issued to purchaser by
Elation Professional; if the product is damaged because not properly maintained as set forth in the product
instructions, guidelines and/or user manual. D. This is not a service contract, and this warranty does not include
any maintenance, cleaning or periodic check-up. During the periods as specified above, Elation Professional will
replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of Elation Professional under this warranty
shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of
Elation Professional. All products covered by this warranty were manufactured after January 1, 1990, and bare
identifying marks to that effect. E. Elation Professional reserves the right to make changes in design and/or
performance improvements upon its products without any obligation to include these changes in any products
theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with the products described above. Except to the extent prohibited by applicable law, all
implied warranties made by Elation Professional in connection with this product, including warranties of
merchantability or fitness, are limited in duration to the warranty periods set forth above. And no warranties,
whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after
said periods have expired. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall Elation Professional be liable for any loss and/or
damage, direct and/or consequential, arising out of the use of, and/or the inability to use, this product. G. This
warranty is the only written warranty applicable to Elation Professional products and supersedes all prior
warranties and written descriptions of warranty terms and conditions heretofore published.

WARRANTY RETURNS

All returned service items whether under warranty or not, must be freight pre-paid and accompany a return
authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A
brief description of the problem as well as the R.A. number must also be written down on a piece of paper and
included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of
purchase invoice. Items returned without a R.A. number clearly marked on the outside of the package will be
refused and returned at customer’s expense. You may obtain a R.A. number by contacting customer support.

5

SAFETY GUIDELINES

PROTECTION CLASS 1 - DEVICE MUST BE PROPERLY GROUNDED

THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT.
DO NOT ATTEMPT ANY REPAIRS YOURSELF; DOING SO WILL VOID
YOUR MANUFACTURES WARRANTY. DAMAGES RESULT ING FRO M
MODIFICATIONS TO THIS DEVICE AND/OR THE DISREGARD OF
SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID
THE MANUFACTURES WARRANTY AND ARE NOT SUBJECT TO ANY
WARRANTY CLAIMS AND/OR REPAIRS.

DO NOT PLUG DEVICE INTO A DIMMER PACK!
NEVER OPEN THIS DEVICE WHILE IN USE!
UNPLUG POWER BEFORE SERVICING DEVICE!
KEEP FLAMMABLE MATERIALS AWAY FROM DEVICE!

INDOOR / DRY LOCATIONS USE ONLY!
DO NOT EXPOSE FIXTURE TO RAIN AND MOISTURE!

This device is a sophisticated piece of electronic equipment. To guarantee a smooth
operation, it is important to follow all instructions and guidelines in this manual. Elation
Professional is not responsible for injury and/or damages resulting from the misuse of this
fixture due to the disregard of the information printed in this manual. Only qualified and/or
certified personnel should perform installation of this device and only the original rigging
parts included with this device should be used for installation. Any modifications to the
device and/or the included mounting hardware will void the original manufactures warranty
and increase the risk of damage and/or personal injury.

6

SAFETY GUIDELINES

DO NOT shake device, avoid brute force when installing and/or operating device.

DO NOT operate device if the power cord is frayed, crimped, damaged and/or if any of the

power cord connectors are damaged and do not insert into the device securely with ease.

NEVER force a power cord connector into the device. If the power cord or any of its

connectors are damaged, replace it immediately with a new one of similar power rating.

DO NOT block any air ventilation slots.

All fan and air inlets must remain clean and never blocked.

Allow approx. 6” (15cm) between the device and other devices or a wall for proper cooling.

When installing device in a suspended environment, always use mounting hardware that is no

less than M10 x 25 mm, and always install device with an appropriately rated safety cable.

Always disconnect device from main power source before performing any type of service

and/or cleaning procedure. Only handle the power cord by the plug end, never pull out the

plug by tugging the wire portion of the cord.

Consistent operational breaks will ensure the device will function properly for many years.

ONLY Use the original packaging and materials to transport the device in for service.

7

MAINTENANCE GUIDELINES

DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!

CLEANING

Frequent cleaning is recommended to insure proper function and extended life. The

frequency of cleaning depends on the environment in which the device operates: damp,

smoky or particularly dirty environments can cause greater accumulation of dirt on the

device and air vents. Clean the external surface at least every 30 days with a soft cloth to

avoid dirt/debris accumulation.

NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

Regular inspections are recommended to insure proper function and extended life.

There are no user serviceable parts inside this device, please refer all other service issues

to an authorized Elation service technician. Should you need any spare parts, please order

genuine parts from your local Elation dealer.

Please refer to the following points during routine inspections:

A detailed electric check by an approved electrical engineer every three months to make sure

the circuit contacts are in good condition and prevent overheating.

Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out

during normal operation resulting in damage or injury as larger parts could fall.

Check for any deformations on the housing, rigging hardware and rigging points (ceiling,

suspension, trussing). Deformations in the housing could allow for dust to enter into the

device. Damaged rigging points or unsecured rigging could cause the device to fall and

seriously injure a person(s).

Electric power supply cables must not show any damage, material fatigue or sediments.

NEVER remove the ground prong from the power cable.

8

DEVICE OVERVIEW

1. LCD System Menu Control Display

2. Mode, Setup, Up, Down Menu Control Buttons

3. Power Switch

4. powerCON Power Cable Input

5. 10A Fuse

6. Safety Cable Attachment Loop

7. RJ45 Ethernet In/Out Ports (Kling-NET, Art-NET/sACN)

8. Output Ports 1-4 (10A Fuse each)

INCLUDED ITEMS

PIXEL DRIVER 4000

19” Rack Mount Kit

powerCON Power Cable

3m (9.8 ft) 4pin 16AWG Power/Data Cable

9

INSTALLATION GUIDELINES

FLAMMABLE MATERIAL WARNING

Keep device minimum 5.0 feet (1.5m) away from flammable materials and/or pyrotechnics.

ELECTRICAL CONNECTIONS

A qualified electrician should be used for all electrical connections and/or installations.

PIXEL DRIVER 400 INDOOR / DRY LOCATIONS USE ONLY!
DO NOT EXPOSE PIXEL DRIVER 4000 TO RAIN AND MOISTURE!

DO NOT INSTALL THE DEVICE IF YOU ARE NOT QUALIFIED TO DO SO!

Device MUST be installed following all local, national, and country commercial electrical

and construction codes and regulations.

Before rigging/mounting the device to any metal truss/structure or placing the device on

any surface, a professional equipment installer MUST be consulted to determine if the

metal truss/structure or surface is properly certified to safely hold the combined weight of

the device, clamps, cables, and accessories. Overhead device installation must always be

secured with a secondary safety attachment, such as an appropriately rated safety cable

that meets all local, national, and country codes and regulations.

Device ambient operating temperature range is 14° to 113°F. (-10° to 45°C)

Do not use the device under or above this temperature.

Device should be installed in areas outside walking paths, seating areas, or away from

areas were unauthorized personnel might reach the fixture by hand.

NEVER stand directly below the device when rigging, removing or servicing.

10

INSTALLATION GUIDELINES

SAFETY CABLE

ALWAYS ATTACH A SAFETY
CABLE TO THE SAFETY CABLE
LOOP ON THE BACK OF THE
DEVICE WHENEVER INSTALLING
THIS DEVICE IN A SUSPENDED
ENVIRONMENT TO ENSURE THE
FIXTURE WILL NOT DROP IF THE
CLAMP FAILS.

RACK MOUNTING

The device can be rack mounted in a standard 19-inch rack space. Attach the included

rack ears to both sides of the device using the included screws. Tighten rack ear screws

securely but do NOT over tighten. Use careful planning when rack mounting the device to

allow ample space for the power/data cables.

TRUSS MOUNTING

The device can be attached to truss or a like structure using an appropriated truss clamp

(not included) and an M10 screw (not included).

RIGGING

Overhead rigging requires extensive experience, including amongst others calculating

working load limits, installation material being used, and periodic safety inspection of all

installation material and the device. If you lack these qualifications, do not attempt the

installation yourself. Improper installation can result in bodily injury.

INSTALLATION LOCATION PLANNING

Use careful planning to select the installation location of the PIXEL DRIVER 4000 unit(s).

The maximum distance from the driver to the first pixel bar can NOT exceed 50 feet (18m).

11

CONNECTIONS AND CABLES

CONNECTIONS

The device features RJ45 Ethernet in/out and 4pin power/data combination output
connections. The wiring diagram below provides the pin details for the power/data outputs.

PIN #1 - (+) Power

PIN #2 - Data

PIN #3 - CLK (clock pin)

PIN #4 - (-) Power

CABLES

ELATION P BAR IP 4pin 16AWG power/data cables are available in various lengths.

See Optional Accessories for details.

MAXIMUM CABLE DISTANCES – 16AWG

The following maximum cable distances apply when using 16AWG cables.
PIXEL DRIVER 4000 to 1st PIXEL BAR IP = Maximum 50 feet (18 meters)
PIXEL BAR IP to PIXEL BAR IP = Maximum 32 feet (10 meters)
Total combined length of cables can NOT exceed = Maximum 98 feet (30 meters)

MAXIMUM CABLE DISTANCES – 12AWG

The following maximum cable distances apply when using 12AWG cables.
PIXEL DRIVER 4000 to 1st PIXEL BAR IP = Maximum 50 feet (18 meters)
PIXEL BAR IP to PIXEL BAR IP = Maximum 32 feet (10 meters)
To ta l co mb in ed l en gt h of cables can NOT exceed = Maximum 213 feet (65 meters)

12

SYSTEM CONFIGURATION

!"#$%&

'"' (%&
)*+$%,&

'"' (%&

-".'/"%&

-0(..$%,&

1%*.23.$'&
45676&!89&):9;<=&>;?&#?:@;?&)A?B&
C56D6&!89&):9;<=&>;?&#?:@;?&EF:B&

!(+&G(/,&
>;?&
#/*H$/&)"/'&

!(+&)*+$%,&
>;?&
#/*H$/&)"/'&

!(+&G(/,&
>;?& &
#/*H$/&E.*'&

!(+&)*+$%,&
>;?& &
#/*H$/&E.*'&

)*+$%&G(/&I6*)&

30#

90#

34#

1020#

136#

4080#

)*+$%&G(/&J6*)&

60#

180#

17#

1020#

68#

4080#

)*+$%&G(/&476*)&

120#

360#8#960#

32#

3840#

!"#$%&

'"' (%&
)*+$%,&

'"' (%&

-".'/"%&

-0(..$%,&

(/'3.$'K=(-.&
4L6&!89&):9;<=&>;?&#?:@;?&)A?B&
JD6&!89&):9;<=&>;?&#?:@;?&EF:B&

!(+&G(/,&
>;?& &
#/*H$/&)"/'&

!(+&)*+$%,&
>;?&
#/*H$/&)"/'&

!(+&G(/,&
>;?& &
#/*H$/&E.*'&

!(+&)*+$%,&
>;?&
#/*H$/&E.*'&

)*+$%&G(/&I6*)&

30#

90#5#150#

20#

600#

)*+$%&G(/&J6*)&

60#

180#2#120#8#480#

)*+$%&G(/&476*)&

120#

360#1#120#4#480#

LINKING

Maximum number pixels/bars each PIXEL DRIVER 4000 supports is listed in charts below.

Multiple combinations of PIXEL BAR IP models can be linked (daisy-chained) together to a

single driver port, providing the maximum number of pixels/bars is NOT exceeded.

KLING-NET = 1,020 Max Pixels per PIXEL DRIVER 4000 Port

Art-NET/sACN = 170 Max Pixels per PIXEL DRIVER 4000 Port

13

SYSTEM CONFIGURATION

CONTROL

PIXEL DRIVER 4000 supports Kling-NET, Art-NET, and sACN control protocols. It can be

controlled by an Art-NET compatible controller/console and for advanced pixel

programming, it can be controlled via a computer with media software such as ArKaos

Media Master. The driver also includes 16 internal programs for easy stand-alone demo

proposes, which can be accessed manually from the 4-button LCD control menu display.

PC – DRIVER DIRECT CONNECTION

Up to 5 PIXEL DRIVER 4000 units can be linked (daisy-chained) from a computer.

For systems requiring more than 5 drivers, see the next section for more information.

PC – NETWORK SWITCH CONNECTION

Up to 50 PIXEL DRIVER 4000 units can be linked (daisy-chained) from a computer and a

Gigabit Ethernet Switch (not included) that supports IGMP (Internet Group

Management Protocol). Using a Gigabit Ethernet Switch that does not support IGMP

can cause erratic behavior of all connected devices to the switch. Click link for more

information about IGMP. https://en.wikipedia.org/wiki/Internet_Group_Management_Protocol

Up to 5 PIXEL DRIVER 4000 units can be connected per ethernet switch port and up to 10

total ethernet switch ports can be used in a system.

14

SYSTEM MENU

Supports Software Versions: ≥ 1.0

Features are subject to change without any prior written notice.

MODE button

SET UP button

UP/DOWN buttons

DESCRIPTION

MANUAL
CONTROL

RED:

000-255

Manually adjust RED LED Intensity

GREEN:

000-255

Manually adjust GREEN LED Intensity

BLUE:

000-255

Manually adjust BLUE LED Intensity

OUT1:

ENABLE/DISABLE

Enable or Disable OUTPUT #1

OUT2:

ENABLE/DISABLE

Enable or Disable OUTPUT #2

OUT3:

ENABLE/DISABLE

Enable or Disable OUTPUT #3

OUT4:

ENABLE/DISABLE

Enable or Disable OUTPUT #3

KLINGNET

PIXEL BAR SETUP

KLINGNET OUT1
PIXEL BAR XXXIP

Set Pixel Bar Model - OUTPUT #1

KLINGNET OUT1
XXXIP NUMBER XX

Set Number of Pixel Bar Model - OUTPUT #1

KLINGNET OUT2
PIXEL BAR XXXIP

Set Pixel Bar Model - OUTPUT #2

KLINGNET OUT2
XXXIP NUMBER XX

Set Number of Pixel Bar Model - OUTPUT #2

KLINGNET OUT3
PIXEL BAR XXXIP

Set Pixel Bar Model - OUTPUT #3

KLINGNET OUT3
XXXIP NUMBER XX

Set Number of Pixel Bar Model - OUTPUT #3

KLINGNET OUT4
PIXEL BAR XXXIP

Set Pixel Bar Model - OUTPUT #4

KLINGNET OUT4
XXXIP NUMBER XX

Set Number of Pixel Bar Model - OUTPUT #4

ARTNET

IP ADDRESS SETUP

IP ADDRESS OUT1
XXX:XXX:XXX:XXX

Set IP Address of OUTPUT #1

IP ADDRESS OUT2
XXX:XXX:XXX:XXX

Set IP Address of OUTPUT #2

IP ADDRESS OUT3
XXX:XXX:XXX:XXX

Set IP Address of OUTPUT #3

IP ADDRESS OUT4
XXX:XXX:XXX:XXX

Set IP Address of OUTPUT #4

UNIVERSE SETUP

UNIVERSE OUT1
UNIVERSE OUT2
UNIVERSE OUT3
UNIVERSE OUT4

UNIVERSE OUT1
00000-32768

Set DMX Universe of OUTPUT #1

UNIVERSE OUT2
00000-32768

Set DMX Universe of OUTPUT #2

UNIVERSE OUT3
00000-32768

Set DMX Universe of OUTPUT #3

UNIVERSE OUT4
00000-32768

Set DMX Universe of OUTPUT #4

15

SYSTEM MENU

Supports Software Versions: ≥ 1.0

Features are subject to change without any prior written notice.

MODE button

SET UP button

UP/DOWN buttons

DESCRIPTION

sACN

UNIVERSE SETUP

UNIVERSE OUT1
UNIVERSE OUT2
UNIVERSE OUT3
UNIVERSE OUT4

sACN OUT1
U00001-64000

Set DMX Universe of OUTPUT #1

sACN OUT1
U00001-64000

Set DMX Universe of OUTPUT #2

sACN OUT1
U00001-64000

Set DMX Universe of OUTPUT #3

sACN OUT1
U00001-64000

Set DMX Universe of OUTPUT #4

PROGRAMS

PROGRAMS
PIXEL BAR SETUP

PROGRAM OUT1
PIXEL BAR XXXIP

Set Pixel Bar Model - OUTPUT #1

PROGRAM OUT1
XXXIP NUMBER XX

Set Number of Pixel Bar Model - OUTPUT #1

PROGRAM OUT2
PIXEL BAR XXXIP

Set Pixel Bar Model - OUTPUT #2

PROGRAM OUT2
XXXIP NUMBER XX

Set Number of Pixel Bar Model - OUTPUT #2

PROGRAM OUT3
PIXEL BAR XXXIP

Set Pixel Bar Model - OUTPUT #3

PROGRAM OUT3
XXXIP NUMBER XX

Set Number of Pixel Bar Model - OUTPUT #3

PROGRAM OUT4
PIXEL BAR XXXIP

Set Pixel Bar Model - OUTPUT #4

PROGRAM OUT4
XXXIP NUMBER XX

Set Number of Pixel Bar Model - OUTPUT #4

PROGRAMS
PROGRAM PLAY

PROGRAMS
PROGRAM 00-16

Select Internal Program Number

PROGRAMS
SPEED 00-16

Select Internal Program Speed

PROGRAMS
FADE 00-16

Select Internal Program Fade

PROGRAMS
PHASE TIME 00-16

Select Internal Program Phase Time

16

SYSTEM MENU

Supports Software Versions: ≥ 1.0

Features are subject to change without any prior written notice.

MODE button

SET UP button

UP/DOWN buttons

DESCRIPTION

KLINGNET&ARTNET

KLINGNET:

ENABLE/DISABLE

Enable or Disable Kling-NET/Art-Net
Auto Detection Mode

KLINGNET SET
PIXEL BAR SETUP

KLINGNET OUT1
PIXEL BAR XXXIP

Set Pixel Bar Model - OUTPUT #1

KLINGNET OUT1
XXXIP NUMBER XX

Set Number of Pixel Bar Model - OUTPUT #1

KLINGNET OUT2
PIXEL BAR XXXIP

Set Pixel Bar Model - OUTPUT #2

KLINGNET OUT2
XXXIP NUMBER XX

Set Number of Pixel Bar Model - OUTPUT #2

KLINGNET OUT3
PIXEL BAR XXXIP

Set Pixel Bar Model - OUTPUT #3

KLINGNET OUT3
XXXIP NUMBER XX

Set Number of Pixel Bar Model - OUTPUT #3

KLINGNET OUT4
PIXEL BAR XXXIP

Set Pixel Bar Model - OUTPUT #4

KLINGNET OUT4
XXXIP NUMBER XX

Set Number of Pixel Bar Model - OUTPUT #4

ARTNET SET
IP ADDRESS SETUP

IP ADDRESS OUT1
XXX:XXX:XXX:XXX

Set IP Address of OUTPUT #1

IP ADDRESS OUT2
XXX:XXX:XXX:XXX

Set IP Address of OUTPUT #2

IP ADDRESS OUT3
XXX:XXX:XXX:XXX

Set IP Address of OUTPUT #3

IP ADDRESS OUT4
XXX:XXX:XXX:XXX

Set IP Address of OUTPUT #4

ARTNET SET
UNIVERSE SETUP

UNIVERSE OUT1
00000-32768

Set DMX Universe of OUTPUT #1

UNIVERSE OUT2
00000-32768

Set DMX Universe of OUTPUT #2

UNIVERSE OUT3
00000-32768

Set DMX Universe of OUTPUT #3

UNIVERSE OUT4
00000-32768

Set DMX Universe of OUTPUT #4

SETUP OPTIONS

BLGT:

ON/OFF

Set LCD Backlight
ON = Always ON | OFF = OFF after 20 sec

BRCO:

000-100

Set LCD Brightness Level

SYSRESET

To Reset ALL Settings to Factory Default
Press UP and DOWN Buttons Together

SYSTEM RESET
ONLY QUALIFIED TECHNICIANS SHOULD PERFORM THIS FUNCTION.
NOTE: ALL SAVED SETTINGS ARE ERASED AFTER A SYSRESET IS PERFORMED.

17

TECHNICAL SPECIFICATIONS

CONTROL / CONNECTIONS

Manual RGB Mode
Internal Programs
Art-NET | sACN | Kling-NET
(2) RJ45 Ethernet Ports
(4) 4pin Power/Data Outputs

SIZE / WEIGHT

Length: 16.7” (425mm)
Width: 11.9” (301mm)
Vertical Height: 2.9” (74mm)
Weight: 9.5 lbs. (4.3 kg)

ELECTRICAL / THERMAL

AC 100-240V - 50/60Hz
800W Max Power Consumption

-4° to 113°F. (-20° to 45°C)

APPROVALS / RATINGS

CE |

Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS

This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection agains t harmf ul interference in a residen tial installation. This dev ice uses and can radiate radio frequency energy
and, if not installed and used in accordance with the included instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to
radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the
interference by one or more of the following methods:

•! Reorient or relocate the device.

•! Increase the separation between the device and the receiver.

•! Connect the device to an electrical outlet on a circuit different from which the radio receiver is connected.

•! Consult the dealer or an experienced radio/TV technician for help.

18

OPTIONAL ACCESSORIES

ORDER CODE

ITEM DESCRIPTION

PIX200

PIXEL BAR 30IP

PIX225

PIXEL BAR 60IP

PIX253

PIXEL BAR 120IP

PIX277

PIXEL DRIVER 4000

PIX300

P BAR IP 0.6m (2ft) 16AWG Cable

PIX313

P BAR IP 1m (3ft) 16AWG Cable

PIX326

P BAR IP 1.5m (5ft) 16AWG Cable

PIX339

P BAR IP 3m (10ft) 16AWG Cable

PIX352

P BAR IP 3.5m (12ft) 16AWG Cable

PIX365

P BAR IP 4.5m (15ft) 16AWG Cable

PIX378

P BAR IP 6m (20ft) 16AWG Cable

PIX391

P BAR IP 7.5m (25ft) 16AWG Cable

PIX411

P BAR IP 9m (30ft) 16AWG Cable

PIX424

P BAR IP 15m (50ft) 16AWG Cable

PIX450

P BAR IP MALE Cable Connector

PIX452

P BAR 30IP Replacement Clear Lens

PIX462

P BAR 30IP Rounded Frost Lens

PIX463

P BAR IP FEMALE Cable Connector

PIX471

P BAR 30IP Square Frost Lens

PIX483

P BAR 60IP Replacement Clear Lens

PIX494

P BAR 60IP Rounded Frost Lens

PIX502

P BAR 60IP Square Frost Lens

PIX515

P BAR 120IP Replacement Clear Lens

PIX526

P BAR 120IP Rounded Frost Lens

PIX537

P BAR 120IP Square Frost Lens

19