Eizo GS220, GX220 User Manual

User’s Manual

Monochrome LCD Monitor

It shall be assured that the final system is in compliance to IEC60601-1-1 requirements.

For U.S.A, Canada, etc. (rated 100-120 Vac) Only

FCC Declaration of Conformity

We, the Responsible Party EIZO NANAO TECHNOLOGIES INC.

5710 Warland Drive, Cypress, CA 90630 Phone: (562) 431-5011

declare that the product Trade name: EIZO

Model: RadiForce GX220/GS220

is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

* Reorient or relocate the receiving antenna. * Increase the separation between the equipment and receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

* Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Note Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference within the limits of a Class B digital device.

- AC Cord

- Shielded Signal Cable (enclosed)

Canadian Notice

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.

English

SAFETY SYMBOLS

This manual uses the safety symbols below. They denote critical information. Please read them carefully.

WARNING

Failure to abide by the information in a WARNING may result in serious injury and can be life threatening.

CAUTION

Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage.

Indicates a prohibited action.

Indicates to ground for safety.

Power supplied equipment can emit electromagnetic waves, that could influence, limit or

•

result in malfunction of the monitor. Install the equipment in a controlled environment, where such effects are avoided.

• • This is a monitor intended for use in a medical image system.

Product specifications may vary depending on the region. Confirm the specifications in the manual written in the language of the region of purchase.

Copyright© 2006 EIZO NANAO CORPORATION All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION. EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information confidential unless prior arrangements are made pursuant to EIZO NANAO CORPORATION's receipt of said information. Although every effort has been made to ensure that this manual provides up-to-date information, please note that EIZO monitor specifications are subject to change without notice.

Apple and Macintosh are registered trademarks of Apple Computer, Inc. VGA is a registered trademark of International Business Machines Corporation. VESA is a registered trademark of Video Electronics Standards Association. Windows is a registered trademark of Microsoft Corporation. RealVision is a registered trademark of RealVision Inc. Matrox is a registered trademark of Matrox Electronic Systems Ltd. PowerManager, RadiCS and RadiNET are trademarks of EIZO NANAO CORPORATION. ScreenManager, RadiForce and EIZO are registered trademarks of EIZO NANAO CORPORATION in Japan and other countries.

English

PRECAUTIONS......................................................................................4

1. INTRODUCTION..................................................................................... 9

1-1. Features....................................................................................................... 9

1-2. Package Contents ........................................................................................9

1-3. Controls & Connectors .............................................................................10

2. INSTALLATION..................................................................................... 12

2-1. Before Connecting .....................................................................................12

2-2. Cable Connection...................................................................................... 12

2-3. Environmental Settings.............................................................................. 15

3. ADJUSTMET & SETTINGS ..................................................................17

3-1. How to use the ScreenManager ................................................................. 17

3-2. ScreenManager menu ................................................................................18

3-3. CAL Switch Function ................................................................................22

3-4. Adjustment Lock Function ........................................................................23

4. BRIGHTNESS ADJUSTMENT & IMAGE ADJUSTMENT....................24

4-1. Brightness Adjustment............................................................................... 24

4-2. Image Adjustments .................................................................................... 24

5. MAKING USE OF USB (Universal Serial Bus)...................................25

6. ATTACHING AN ARM ...........................................................................27

7. TROUBLESHOOTING...........................................................................28

8. CLEANING............................................................................................31

9. SPECIFICATIONS.................................................................................32

10. GLOSSARY.........................................................................................36

TABLE OF CONTENTS 3

English

PRECAUTIONS

IMPORTANT!

• This product has been adjusted specifically for use in the region to which it was originally shipped. If operated outside the region to which it was originally shipped, the product may not perform as stated in the specifications.

• To ensure personal safety and proper maintenance, please read this section and the caution statements on the unit (refer to the figure below).

[Location of the Caution Statements]

[Symbols on the unit]

Symbol

Rear Main power switch

Front Control panel

Rear Name Plate

Rear

Location

This symbol indicates

Press to turn the monitor’s main power off.

Press to turn the monitor’s main power on.

Power switch Touch to turn the monitor’s power on or off.

Alternating current

Alerting electrical hazard

Caution Refer to SAFETY SYMBOLS section in this

manual.

4 PRECAUTIONS

English

WARNING

If the unit begins to emit smoke, smells like something is burning, or makes strange noises, disconnect all power connections immediately and contact your dealer for advice.

Attempting to use a malfunctioning unit may result in fire, electric shock, or equipment damage.

Do not open the cabinet or modify the unit.

Opening the cabinet or modifying the unit may result in fire, electric shock, or burn.

Refer all servicing to qualified service personnel.

Do not attempt to service this product yourself as opening or removing covers may result in fire, electric shock, or equipment damage.

Keep small objects or liquids away from the unit.

Small objects accidentally falling through the ventilation slots into the cabinet or spillage into the cabinet may result in fire, electric shock, or equipment damage.

If an object or liquid falls/spills into the cabinet, unplug the unit immediately. Have the unit checked by a qualified service engineer before using it again.

Place the unit at the strong and stable place.

A unit placed on an inadequate surface may fall and result in injury or equipment damage.

If the unit falls, disconnect the power immediately and ask your dealer for advice. Do not continue using a damaged unit. Using a damaged unit may result in fire or electric shock.

Set the unit in an appropriate location.

Not doing so may result in fire, electric shock, or equipment damage.

* Do not place outdoors. * Do not place in the transportation system (ship, aircraft, trains, automobiles,

etc.)

* Do not place in a dusty or humid environment. * Do not place in a location where the steam comes directly on the screen. * Do not place near heat generating devices or a humidifier. * Do not place in an inflammable gas environment.

To avoid danger of suffocation, keep the plastic packing bags away from babies and children.

Use the enclosed power cord and connect to the standard power outlet of your country.

Be sure to remain within the rated voltage of the power cord. Not doing so may result in fire or electric shock. Power supply: 100-120/200-240 VAC±10 %, 50/60 Hz

PRECAUTIONS

English

WARNING

To disconnect the power cord, grasp the plug firmly and pull.

Tugging on the cord may damage and result in fire or electric shock.

The equipment must be connected to a grounded main outlet.

Not doing so may result in fire or electric shock.

Use the correct voltage.

* The unit is designed for use with a specific voltage only. Connection to

another voltage than specified in this User’s Manual may cause fire, electric shock, or equipment damage. Power supply: 100-120/200-240 VAC±10 %, 50/60 Hz

* Do not overload your power circuit, as this may result in fire or electric

shock.

Handle the power cord with care.

* Do not place the cord underneath the unit or other heavy objects.

* Do not pull on or tie the cord.

If the power cord becomes damaged, stop using it. Use of a damaged cord may result in fire or electric shock.

Never touch the plug and power cord if it begins to thunder.

Touching them may result in electric shock.

When attaching an arm stand, please refer to the user’s manual of the arm stand and install the unit securely.

Not doing so may cause the unit to come unattached, which may result in injury or equipment damage. When the unit is dropped, please ask your dealer for advice. Do not continue using a damaged unit. Using a damaged unit may result in fire or electric shock. When reattaching the tilt stand, please use the same screws and tighten them securely.

6 PRECAUTIONS

English

WARNING

Do not touch a damaged LCD panel directly with bare hands.

The liquid crystal which leaks from the panel is poisonous if it enters the eyes or mouth.

If any part of the skin or body comes in direct contact with the panel, please wash thoroughly. If some physical symptoms result, please consult your doctor.

Follow local regulation or laws for safe disposal.

The backlight of the LCD panel contains mercury.

CAUTION

Handle with care when carrying the unit.

Disconnect the power cord and cables when moving the unit. Moving the unit with the cord attached is dangerous. It may result in injury.

When handling the unit, grip the bottom of the unit firmly with both hands ensuring the panel faces outward before lifting.

Dropping the unit may result in injury or equipment damage.

Do not block the ventilation slots on the cabinet.

* Do not place any objects on the ventilation slots. * Do not install the unit in a closed space. * Do not use the unit laid down or upside down.

Blocking the ventilation slots prevents proper airflow and may result in fire, electric shock, or equipment damage.

Do not touch the plug with wet hands.

Doing so may result in electrical shock.

Use an easily accessible power outlet.

This will ensure that you can disconnect the power quickly in case of a problem.

Periodically clean the area around the plug.

Dust, water, or oil on the plug may result in fire.

Unplug the unit before cleaning it.

Cleaning the unit while it is plugged into a power outlet may result in electric shock.

If you plan to leave the unit unused for an extended period, disconnect the power cord from the wall socket after turning off the power switch for the safety and the power conservation.

PRECAUTIONS

English

LCD Panel

The screen may have defective pixels. These pixels may appear as slightly light or dark area on the screen. This is due to the characteristics of the panel itself, and not the product.

The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer.

Do not press on the panel or edge of the frame strongly, as this may result in damage to the screen. There will be prints left on the screen if the pressed image is dark or black. If pressure is repeatedly applied to the screen, it may deteriorate or damage your LCD panel. Leave the screen white to decrease the prints.

Do not scratch or press on the panel with any sharp objects, such as a pencil or pen as this may result in damage to the panel. Do not attempt to brush with tissues as this may scratch the LCD panel.

When the screen image is changed after displaying the same image for extended periods of time, an afterimage may appear. Use the screen saver or timer to avoid displaying the same image for extended periods of time.

When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation may occur inside and outside the monitor. In that case, do not turn the monitor on and wait until dew condensation disappears, otherwise it may cause some damages to it.

8 PRECAUTIONS

1. INTRODUCTION

Thank you for choosing an EIZO Monochrome Monitor.

1-1. Features

• DVI (p. 36) Digital input compliant for TMDS (p. 36)

• [Horizontal scanning frequency] 31 - 100 kHz

[Vertical scanning frequency] 48 ~ 71.5 Hz (VGA text: 69 - 71 Hz) [Frame synchronous mode] 59 - 61 Hz supported [Resolution] 2M pixels (Portrait: 1200 × 1600 dots (H × V))

• CAL Switch function for selecting an optimal calibration mode (p. 22)

• Selectable screen compliant with DICOM Part 14 (p. 36)

• USB (Universal Serial Bus) hub support (p. 25)

• Utility software “ScreenManager Pro for Medical”, which enables control of the

monitor from a Windows PC with a mouse or keyboard (refer to the EIZO LCD Utility Disk).

• Monitor stand adjustable for different heights

• Slim bezel

• Built-in Swing Sensor

This sensor is used when calibrating the monitor with the exclusive software RadiNET Pro / RadiCS (see "Options" p. 34).

(GX220-CL only)

English

1-2. Package Contents

Please contact your local dealer for assistance if any of the listed items are missing or damaged.

• LCD Monitor

• Power Cord

• Signal Cable (FD-C39)

• EIZO USB Cable (MD-C93)

The landscape position is the default monitor orientation. For the portrait position, rotate the

monitor ninety degrees counter-clockwise before installing it.

NOTE

• Please retain the packing materials for future transport of the monitor.

• EIZO LCD Utility Disk

• User’s Manual

• LIMITED WARRANTY

• Cleaning Kit “ScreenCleaner”

(GX220-CL only)

1. INTRODUCTION

English

1-3. Controls & Connectors

Front

ScreenManager main menu



CAL Switch menu

Control Panel

(1) MODE Mode Switch (2)

(3)

(4)

(5)

Enter Switch

Directing Switches (Left, Down, Up, Right)

Power Switch

Power Indicator*2

Green Operational Orange Power saving Flashing orange slowly Power off (Main power is on) Off Main Power off

When the monitor is oriented in the landscape position, these switches can be changed to Up,

Left, Right, and Down (p. 15).

To disable the power indicator while the monitor is operational, see p. 21. For power indicator

status when using the “Off Timer,” see p. 21.

10 1. INTRODUCTION

English

Side / Rear

(6)

(7)

(8)

(9)

DVI-D connector

USB upstream port (x 1)

USB downstream ports (x 2)

Power connector

(10)

(11)

(12) Monitor stand with adjustable height (detachable)

Security lock slot*3

Main Power Switch

Allows for connection of a security cable. This lock supports Kensington’s MicroSaver security system. For further information, please consult:

Kensington Technology Group 2855 Campus Drive, San Mateo, CA 94403 USA Tel.: 800-650-4242, x3348, Intl: 650-572-2700, x3348 Fax: 650-572-9675 http://www.kensington.com

The LCD monitor can be oriented in the landscape position. (It can rotate clockwise ninety degrees.) By removing the monitor stand, the LCD monitor can be used with the optional arm stand (p. 27).

1. INTRODUCTION

+ 26 hidden pages