Eizo G22-BL, G22-CL User Manual

User’s Manual

Monochrome LCD Monitor

It shall be assured that the final system is in compliance
to IEC60601-1-1 requirements.

English

SAFETY SYMBOLS

This manual uses the safety symbols below. They denote critical information. Please read them
carefully.

WARNING

Failure to abide by the information in a WARNING may result in serious injury and
can be life threatening.

CAUTION

Failure to abide by the information in a CAUTION may result in moderate injury
and/or property or product damage.

Indicates a prohibited action.

Indicates to ground for safety.

Power supplied equipment can emit electromagnetic waves, that could influence, limit or

•

result in malfunction of the monitor. Install the equipment in a controlled environment, where
such effects are avoided.

• This is a monitor intended for use in a medical setting.

Copyright© 2004 EIZO NANAO CORPORATION All rights reserved. No part of this manual
may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO
CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or
information confidential unless prior arrangements are made pursuant to EIZO NANAO
CORPORATION’s receipt of written information. Although every effort has been made to
ensure that this manual provides up-to-date information, please note that EIZO monitor
specifications are subject to change without notice.

PowerManager and RadiCS are trademarks of EIZO NANAO CORPORATION.
ScreenManager, RadiForce and EIZO are registered trademarks of EIZO NANAO
CORPORATION in Japan and other countries.

2

TABLE OF CONTENTS

PRECAUTIONS...................................................................................4

1. INTRODUCTION .....................................................................................9

1-1. Features ........................................................................................................9

1-2. Package Contents..........................................................................................9

1-3. Controls & Connectors ..............................................................................10

2. CABLE CONNECTION ......................................................................... 12

3. ScreenManager....................................................................................15

3-1. How to use the ScreenManager ..................................................................15

3-2. ScreenManager Adjustments and Settings...................................................16

3-3. Useful Functions .........................................................................................17

3-4. Power-save Setup........................................................................................19

4. MAKING USE OF USB (Universal Serial Bus)...................................20

English

5. ATTACHING AN ARM ...........................................................................22

6. TROUBLESHOOTING...........................................................................24

7. CLEANING............................................................................................27

8. SPECIFICATIONS.................................................................................28

9. GLOSSARY...........................................................................................31

TABLE OF CONTENTS

3

English

PRECAUTIONS

IMPORTANT!

• This product has been adjusted specifically for use in the region to which it was
originally shipped. If operated outside the region to which it was originally shipped,
the product may not perform as stated in the specifications.

• To ensure personal safety and proper maintenance, please read this section and the
caution statements on the unit (refer to the figure below).

[Location of the Caution Statements]

SIGNAL1

POWERINPUT

[Symbols on the unit]

Symbol Location This symbol indicates

4 PRECAUTIONS

Side Main power switch

Press to turn the monitor’s main power off.

Side Main power switch

Press to turn the monitor’s main power on.
Front
Control panel

Rear
Name Plate
Rear
Name Plate

Rear
Name Plate

Power button

Press to turn the monitor’s power on or off.

Alternating current

Alerting electrical hazard

Caution

Refer to SAFETY SYMBOLS section in this

manual.

WARNING

If the unit begins to emit smoke, smells like something is burning, or
makes strange noises, disconnect all power connections immediately
and contact your dealer for advice.

Attempting to use a malfunctioning unit may result in fire, electric shock, or
equipment damage.

Do not open the cabinet or modify the unit.

Opening the cabinet or modifying the unit may result in fire, electric shock, or
burn.

Refer all servicing to qualified service personnel.

Do not attempt to service this product yourself as opening or removing covers
may result in fire, electric shock, or equipment damage.

Keep small objects or liquids away from the unit.

Small objects accidentally falling through the ventilation slots into the cabinet
or spillage into the cabinet may result in fire, electric shock, or equipment
damage.

If an object or liquid falls/spills into the cabinet, unplug the unit immediately.
Have the unit checked by a qualified service engineer before using it again.

English

Place the unit at the strong and stable place.

A unit placed on an inadequate surface may fall and result in injury or
equipment damage.

If the unit falls, disconnect the power immediately and ask your dealer for
advice.

Do not continue using a damaged unit. Using a damaged unit may result in
fire or electric shock.

Set the unit in an appropriate location.

Not doing so may result in fire, electric shock, or equipment damage.

*

Do not place outdoors.

*

Do not place in the transportation system (ship, aircraft, trains, automobiles,
etc.)

*

Do not place in a dusty or humid environment.

*

Do not place in a location where the steam comes directly on the screen.

*

Do not place near heat generating devices or a humidifier.

*

Do not place in an inflammable gas environment.

OK

PRECAUTIONS

5

English

p

y

WARNING

To avoid danger of suffocation, keep the plastic packing bags away
from babies and children.

Use the enclosed power cord and connect to the standard power outlet
of your country.

Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.

To disconnect the power cord, grasp the plug firmly and pull.

Tugging on the cord may damage and result in fire or electric shock.

The equipment must be connected to a grounded main outlet.

Not doing so may result in fire or electric shock.

Use the correct voltage.

* The unit is designed for use with a specific voltage only. Connection to

another voltage than specified in this User’s Manual may cause fire, electric
shock, or equipment damage.

* Do not overload your power circuit, as this may result in fire or electric

shock.

Handle the power cord with care.

* Do not place the cord underneath the unit or other heavy objects.
* Do not pull on or tie the cord.

If the
result in fire or electric shock.

Never touch the plug and power cord if it begins to thunder.

Touching them may result in electric shock.

ower cord becomes damaged, stop using it. Use of a damaged cord ma

OK

6 PRECAUTIONS

WARNING

pp

g

y

When attaching an arm stand, please refer to the user’s manual of the
arm stand and install the unit securely with the enclosed screws.

Not doing so may cause the unit to become unattached, which may result in
injury or equipment damage. When the unit is dro
for advice. Do not continue usin
result in fire or electric shock. When reattaching the tilt stand, please use the
same screws and tighten them securely.

Do not touch a damaged LCD panel directly with bare hands.

The liquid crystal that may leak from the panel is poisonous if it enters the
eyes or mouth.

If any part of the skin or body comes in direct contact with the panel, please
wash thoroughly. If some physical symptoms result, please consult your
doctor.

Follow local regulation or laws for safe disposal.

The backlight of the LCD panel contains mercury.

a damaged unit. Using a damaged unit ma

ed,please ask your dealer

English

CAUTION

Handle with care when carrying the unit.

Disconnect the power cord and signal cables and remove the optional unit.
Moving the unit with the cord or the option attached is dangerous. It may
result in injury.

When handling the unit, grip the bottom of the unit firmly with both
hands ensuring the panel faces outward before lifting.

Dropping the unit may result in injury or equipment damage.

Do not block the ventilation slots on the cabinet.

* Do not place any objects on the ventilation slots.

* Do not install the unit in a closed space.
* Do not use the unit laid down or upside down.

Blocking the ventilation slots prevents proper airflow and may result in fire,
electric shock, or equipment damage.

OK

PRECAUTIONS

7

English

CAUTION

Do not touch the plug with wet hands.

Doing so may result in electric shock.

Use an easily accessible power outlet.

This will ensure that you can disconnect the power quickly in case of a
problem.

Periodically clean the area around the plug.

Dust, water, or oil on the plug may result in fire.

Unplug the unit before cleaning it.

Cleaning the unit while it is plugged into a power outlet may result in electric
shock.

If you plan to leave the unit unused for an extended period, disconnect
the power cord from the wall socket after turning off the power switch
for the safety and the power conservation.

LCD Panel

In order to suppress the luminosity change by long-term use and to maintain
the stable luminosity, please use the monitor with the brightness below 500

2

cd/m (equal to default setting of BRIGHTNESS approximately 70 %).
The screen may have defective pixels. These pixels may appear as slightly light

or dark area on the screen. This is due to the characteristics of the panel itself,
and not the product.

The backlight of the LCDpanel has a fixed life span. When the screen becomes
dark or begins to flicker, please contact your dealer.

Do not press on the panel or edge of the frame strongly, as this may result in
damage to the screen. There will be prints left on the screen if the pressed
image is dark or black. If pressure is repeatedly applied to the screen, it may
deteriorate or damage your LCD panel. Leave the screen white to decrease the
prints.

Do not scratch or press on the panel with any sharp objects, such as a pencil or
pen as this may result in damage to the panel. Do not attempt to brush with
tissues as this may scratch the panel.

8 PRECAUTIONS

1. INTRODUCTION

Thank you very much for choosing an EIZO Monochrome Monitor.

1-1. Features

• DVI (p.31) Digital input (TMDS (p.31)) compliant

• [Resolution] 2M pixels (1600 dots × 1200 lines)

[Horizontal scanning frequency] 75 kHz
[Vertical scanning frequency] 60 Hz

• USB (Universal Serial Bus) hub supported (p.20)

• The height adjustable stand incorporated

• Ultra slim bezel incorporated

• Power saving function (p.18) (DVI-DMPM(p.31))

NOTE

• Regarding the scanning resolution, the G22-BL/G22-CL supports only the exclusive
timing.

English

1-2. Package Contents

Please contact your local dealer for assistance if any of the listed items are missing or
damaged.

• LCD Monitor

• Power Cord

• Signal Cable (FD-C39)

• EIZO USB Cable (MD-C93)

• User’s Manual

• LIMITED WARRANTY

*1

The orientation of display is landscape position at the default setting. For the

portrait display, pivot the panel in the counter-clockwise direction 90° before
installing the monitor.

NOTE

• Please retain the packing materials for future transference.

*1

1. INTRODUCTION

9

English

1-3. Controls & Connectors

Front 

(1)

(2)

R

E

T

N

Control Panel

(1) ScreenManager
(2)
(3) ENTER
(4)

(5)
(6)

Main Power Switch



 Control Buttons (Left, Down, Up, Right)

 

 Power Indicator

®

Enter Button

Power Button

E

(3) (4) (5)

*2

(6)

*1

Green Operation
Orange Power saving
Flashing orange (2 times for each) Power save mode
Flashing orange slowly Power is off (Main power is on)
Off Power off

*1

These buttons are changed to Up, Left, Right, Down in case of selecting

“Landscape” for <Orientation> of ScreenManager <Others> (p.16).

*2

Green lighting when the screen is displayed (Operation mode) can be changed to

non-light, see page 16.

Regarding the power indicator for the off timer, see page 17.

10 1. INTRODUCTION

Rear 

English

(9)

(10)

(11)

(7)

(8)

(12)

Side

(7) Height Adjustable Stand (Detachable)

(8)
(9)
(10)

(11)
(12)

Security Lock Slot

USB Port (1 Upstream)

USB Port (2 Downstream)

DVI-D Input Connector

Power Connector

*3

The LCD monitor has the capability of the Portrait/Landscape display. (The panel

* 3

*4

pivots in the clockwise direction 90°.) The LCD monitor can be used with an
optional arm stand by removing the stand (p.22).

*4

Allows for connection of a security cable. This lock supports Kensington’s

MicroSaver security system. For further information, please consult’
Kensington Technology Group
2855 Campus Drive, San Mateo, CA 94403 USA
Tel.: [phone], x3348, Intl: 650-572-2700, x3348, Fax: [phone]
http://www.kensington.com

1. INTRODUCTION

11

English

2. CABLE CONNECTION

NOTE

• Be sure that the power switches of both the PC and the monitor are OFF.

• Please refer to the manual of the PC also to connect the monitor.

1. Pivot the panel in the counter-clockwise to fix in portrait position.

2. Plug the signal cable into the connector at the rear of the monitor

and the other end of the cable into the video connector on the PC.

After connecting, secure the connection with the screw-in fasteners.

90

°

Signal Cable
FD-C39

Power Cord

Signal Cable Connector PC

Signal Cable (FD-C39 enclosed)

3.

Plug the power cord into the power connector on the rear of the

Video Output Connector /
DVI

monitor.

SIGNAL1

POWERINPUT

Exclusive graphics board

12 2. CABLE CONNECTION

English

4. Lead the power cord and signal cable into the cable holder at rear of

the monitor.

NOTE

• When housing the cables into the cable holder, lead them to the cable entrance
side and pinch the projection to open the cable entrance.

• The cables are recommended to lead with slight sag for the smooth motion of
the stand.

Projection

Cable Holder

Cable Entrance

5. Plug the other end of the power cord into a power outlet.



WARNING

Use the enclosed power cord and connect to the standard
power outlet of your country.

Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.

The equipment must be connected to a grounded main
outlet.

Not doing so may result in fire or electric shock.



2. CABLE CONNECTION

13

English

6. Turn on the monitor’s Power Button and then switch on the PC’s

power.

The monitor’s power indicator will light up (green).
If an image does not appear, refer to the “6. TROUBLESHOOTING” (p.24) for

advice.
Whenever finished, turn off the PC and the monitor.

7. Set the kind of graphics card.

“8bit” of “Monochrome” (the 8bit monochrome graphics card) is set as default.
If your computer is equipped with the 10bit monochrome graphics card or the 8bit

color graphics card, follow the procedure below.

(1) Select the <Signal Selection> in the ScreenManager (p.15) <Others> menu.

(2) Set the graphics card equipped the computer.

8. When using the optional calibration kit (p.29), connect the upstream

port of the monitor to the downstream port of the USB compliant
PC with the USB cable.

For further details about the calibration, refer to user’s manual in the calibration
kit.

NOTE

• Adjust brightness of the screen depending on the brightness of your environment.

• Be sure to take adequate rests. A 10-minute rest period each hour is suggested.

14 2. CABLE CONNECTION

3. ScreenManager

3-1. How to use the ScreenManager

ScreenManager

Main Menu

English

Enter Button

Control Buttons
Left, Down, Up, Right

1. Entering the ScreenManager

Press the Enter Button once to display the main menu of the ScreenManager.

2. Making Adjustments and Settings

(1) Select the desired sub menu icon using the Control Buttons and press the Enter

Button. The sub menu appears.

(2) Use the Control Buttons to select the desired setting icon and press the Enter

Button. The setting menu appears.

(3) Use the Control Buttons to make all required adjustments and press the Enter

Button to save the settings.

3. Exiting the ScreenManager

(1) To return to the main menu, select the <Return> icon or press the Down Button

twice, followed by the Enter Button.

(2) To exit the ScreenManageru, select the <Exit> icon or press the Down Button

twice, followed by the Enter Button.

NOTE

• Double clicking the Enter Button also exits the ScreenManager menu.

3. ScreenManager

15

English

3-2. ScreenManager Adjustments and Settings

The following table shows all the ScreenManager’s adjustment and setting menus.

Main menu Sub menu Reference

Screen

LUT Setting Default / Normal

PowerManager DVI DMPM 3-4. Power-save Setup. (p.19)
Others

Information Information Review the ScreenManager’s settings,

Language English/Japanese Select the ScreenManager’s language.

*1

Directly pressing the Control Buttons also adjusts the brightness.

*2

Set to the “Normal” in case of using the monitor with the characteristic of panel
original.

*3

“Custom” automatically stores the customized data after the calibration is performed.

*4

Due to the inspection on the factory, the usage time may not be “0 hour” at shipping.

Brightness*1 Control the brightness for the entire

screen.

Unlock Unlock the lock. (p.18)

*2

/ Custom

*3

Set the LUT (Look-up table) (p.31)
setting.

Off Timer Set the monitor’s off timer to on or off.

(p.17)

Settings

Menu Position
Menu Off Timer

Adjust the menu position. Menu
Set the menu displaying time.

Orientation Change the orientation of the

ScreenManager for monitor’s portrait

position.
Signal Selection Set the kind of graphics card.
Power Indicator Make non-light for green lighting when

the screen is displayed.
Reset Return to the factory default settings.

(p.29)

model name, serial number and usage

*4

time

.

16 3. ScreenManager

3-3. Useful Functions

Adjustment Lock

Use the “Adjustment Lock” function to prevent any accidental changes.

Locked function

[How to lock]

(1) Switch off the monitor’s power by the power button on the control panel.
(2) Press on the Enter button while switching on the monitor’s power.

[How to unlock]

(1) Switch off the monitor’s power by the power button on the control panel.
(2) Hold down the Enter button once again and turn the power back on.

Off Timer

The off timer function causes the monitor to automatically enter a power off state after
a predetermined amount of time has lapsed. This function was created to reduce
afterimage (p.31) characteristics that are particular to LCD monitors when the monitor
screen is left on for a long period without use.

• Settings in the ScreenManager.

• Adjustment of brightness by the Control Buttons.

English

[Procedure]

(1) Select <Off Timer> in the ScreenManager <Others> menu.
(2) Select “Enable” and press the Right and Left Buttons to adjust the “On Period” (1

to 23 hours).

[Off timer System]

PC Monitor Power Indicator

On Period (1H - 23H) Operation Green
Last 15 min. in “On period” Advance Notice *1 Green Flashing
“On period” expire Power off Flashing orange slowly

*1

Advance notice (Power Indicator flashing green) will be given 15 minutes before the monitor
automatically enters the “Power Off” mode. To delay entering the “Power Off” mode, press
the Power Button during the advance notice period. The monitor will continue to operate for
an additional 90 minutes.

[Power Resumption Procedure]

Press the Power Button to return to a normal screen.

NOTE

• The off timer function works while the PowerManager is active, but there is no
advance notice before the monitor’s power is switched off.

3. ScreenManager

17

English

Unlock Function after Calibration

The calibration is available when using the specified optional calibration kit (p.29).
After the calibration, the functions below are automatically locked.

Locked function

Unlock function is available by using ScreenManager.

[How to unlock]

(1) Select the <Unlock> of <Screen> menu.
(2) Select “Unlock”.

• Brightness adjustment (including the adjustment by Left and

Right Buttons on the control panel)

• LUT Setting

NOTE

• Performing the <Reset> of <Others>, locked functions are also unlocked.

18 3. ScreenManager

3-4. Power-save Setup

The <PowerManager> menu in the ScreenManager enables to set the power-save setup.

NOTE

• Do your part to conserve energy, turn off the monitor when you are finished using it.
Disconnecting the monitor from the power supply is recommended to save energy
completely.

• Even if the monitor is in a power saving mode, USB compliant devices function
when they are connected to the monitor’s USB (both the upstream and the
downstream ports). Therefore, power consumption of the monitor will change
according to the connected devices even if the monitor is in a power saving mode.

This monitor complies with the DVI DMPM (p.31).

[Procedure]

(1) Set the PC’s power saving settings.
(2) Select “DVI DMPM” in the <PowerManager> menu.

[Power saving system]

PC Monitor Power Indicator

Operation Operation Green
Power saving Power saving Orange

Off mode Power saving

English

Flashing orange
(2 times for each)

[Procedure]

Operate the mouse or keyboard to return to a normal screen.
Power on the PC to return a normal screen from the Off mode of the PC.

3. ScreenManager

19

English

4. MAKING USE OF USB (Universal Serial Bus)

This monitor provides a hub which supports the USB standard. When connecting to a
USB compliant PC or another hub, the monitor functions as a hub to which the USB
compliant peripherals can be easily connected.

Required system environment

• PC with build-in USB ports or another USB hub connected to the USB compliant PC

• EIZO USB Cable (MD-C93)

NOTE

• The USB hub function may not work properly depending on the PC or peripherals.
Please consult the manufacturer of each device about the USB support.

• Using the USB Rev. 2.0 compatible PC or peripherals is recommended.

• When the monitor is not on, the peripherals connected to the downstream ports will

not operate.

• Even if the monitor is in a power saving mode, the devices connected to the
monitor’s USB ports (both the upstream and the downstream) will function.

Connecting to the USB HUB

1. Connect the monitor to the PC with the signal cable (p.12) first, then

turn on the PC.

2. Connect the upstream port of the monitor to the downstream port of

the USB compliant PC or another hub by using the USB cable.

Upstream Port:

Connect the USB compliant PC or
another hub using the USB cable.

After connecting the USB cable, the USB function can be set up automatically.

To Downstream
Ports of the PC
or Another Hub

Upstream Port

20 4. MAKING USE OF USB (Universal Serial Bus)

English

3. After setting up, the monitor’s USB hub is available for connecting

USB compliant peripherals to the downstream ports of the monitor.

Connecting Examples

Monitor

PC

Keyboard

Downstream Ports:

Connect the cables from USB
compliant peripherals such as a
mouse, keyboard, etc.

Mouse

Printer
Keyboard

Downstream
Por ts

Printer

4. MAKING USE OF USB (Universal Serial Bus)

21

English

5. ATTACHING AN ARM

The LCD monitor can be used with an arm by removing the tilt stand and attaching the
arm or stand to the LCD monitor.

NOTE

• If you will use the arm or stand of other companies, confirm the followings to the arm
or stand maker before selecting.

- Hole spacing on the arm mounting: 100 mm x 100 mm (VESA compliant)

- Supportable Weight: Total weight of the monitor (without stand) and attaching

equipment such as a cable

- TÜV/GS approved arm or stand

• Please connect cables after attaching an arm stand.

Setup Procedure

1. Hold the center of the stand mounting cover and slide them

rightward or leftward to remove the mounting cover.

2. Lay the LCD monitor down. Do not scratch the panel.

3. Remove the tilt stand by loosening the screws.

(4 pcs of M4 x 10 mm)

22 5. ATTACHING AN ARM

Stand mounting cover

4. Attach an arm stand to the LCD monitor securely.

Arm-stand

4 Mounting Screws: M4 × 10 (mm)

English

5. ATTACHING AN ARM

23

English

6. TROUBLESHOOTING

If a problem persists even after applying the suggested remedies, contact an EIZO dealer.

• No picture problems → See No.1 - No.2

• Imaging problems → See No.3 - No.7

• Other problems → See No.8 - No.9

• USB problems → See No.10 - No.11

Problems Points to check with possible solutions

1. No picture

• Indicator status: Off

• Indicator status: Green

• Indicator status: Orange

• Indicator status: Slowly flashing

Orange

• Indicator status: Flashing Orange
(twice for each)

2. Error message shown below will
remain on the screen for 40
seconds.

3. Error message shown below will
appears.

• The message appears when the signal
is out of input range. ([Input Range]
Resolution: 1600 x 1200, Frequency:
60 Hz)

Check that the power cord is correctly connected.

If the problem persists, turn off the monitor power
for a few minutes, then turn it back on and try
again.

Check the “Brightness” setting.
Try pressing a key on the keyboard, or clicking the

mouse. (p.19)

Try pressing the Power Button.

Try turning the PC on.

This message appears when the signal is not inputted
correctly, even if the monitor functions properly.

When the image is displayed correctly after a short

time, there is no problem with the monitor. (Some
PCs do not output the signal soon after powering
on.)

Check that the PC is turned ON.
Check that the signal cable is properly connected to

the PC or graphics board.

Use the graphics board's utility software to change

the frequency setting. (Refer to the manual of the
graphics board.)

24 6. TROUBLESHOOTING

Problems Points to check with possible solutions

4. The screen is too bright or too
dark.

5. Afterimages appear.

6. The screen has defective pixels
(e.g. slightly light or dark).

7. Fingerprints remain on the
screen.

8. “Locked!” message appears and
the adjustment controls are not
available when pressing the
Control Buttons.

English

Adjust the <Brightness>. (The backlight of the LCD

monitor has a fixed life span. When the screen
becomes dark or begins to flicker, please contact
your dealer.)

When the screen image is changed after displaying

the same image for a long period, an afterimage
may appear. The “Afterimage” can be removed
gradually by changing the displayed image. Use the
“Off Timer” function and avoid keeping the screen
on all the time. (p.17)

This is due to the characteristics of the panel itself

and not the LCD product.

Leaving the screen white may solve the problem.

After the calibration, the functions like brightness

are automatically locked. Please refer to page 18 to
unlock.

9. The Main menu of
ScreenManager does not
operate.

10. USB function cannot be setup.

The adjustment lock is probably on. To unlock:

switch the LCD monitor off. Then, while pressing
the Enter Button, switch the power on. (p.17)

Check that the USB cable is correctly connected.
Check that the PC and OS are USB compliant. (For

verification of USB support, consult the
manufacturer of each system.)

Check the PC’s BIOS setting for USB. (For details,

refer to the manual of the PC.)

6. TROUBLESHOOTING

25

English

Problems Points to check with possible solutions

11. PC is hung up. / The peripherals
connected to the downstream
ports do not operate.

Check that the USB cable is correctly connected.
Check the downstream ports by connecting the

peripherals to other downstream ports. If the
problem is solved by doing this, contact an EIZO
dealer. (For details, refer to the manual of the PC.)

Try executing the following method.

- Restarting the PC

- Connecting the PC and peripherals directly

If the problem is solved by doing this, contact an
EIZO dealer.

26 6. TROUBLESHOOTING

7. CLEANING

Periodic cleaning is recommended to keep the monitor looking new and to prolong its
operation lifetime.

NOTE

• Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol),
abrasive cleaners, or other strong solvents, as these may cause damage to the
cabinet or LCD panel.

Cabinet

To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild
detergent. Do not spray wax or cleaner directly into the cabinet.

LCD Panel

• The LCD surface can be cleaned with a soft cloth, such as cotton or lens paper.

• If necessary, stubborn stains can be removed by moistening part of a cloth with water

to enhance its cleaning power.

English

7. CLEANING

27

English

8. SPECIFICATIONS

LCD Panel 50 cm (19.6 inch), TFT Monochrome LCD panel

Anti-Glare Hard Coating 3H, Response Time: approx. 40 ms
Viewing Angle
Dot Pitch 0.249 mm
Horizontal Scan Frequency 75 kHz (only exclusive timing supported)
Vertical Scan Frequency 60 Hz (only exclusive timing supported)
Resolution 2M pixels (1600 dots × 1200 lines)
Dot Clock 162 MHz
Gray Scale 1024 steps of 3061 steps
Display Area 398.4 mm (H) × 298.8 mm (V) (15.7” (H) × 11.8” (V))

Power Supply

Power Consumption Min.: 65 W, Max.: 85 W (With USB hub)

Input Connector DVI-D × 1

Horizontal: 170°, Vertical: 170° (CR≥10)

(Viewable image size: 498 mm (19.6”))

100-120/200-240 VAC ±10%, 50/60 Hz, 0.9-0.7/0.5-0.4 A

Power Saving Mode: Less than 6 W (When the USB hub are not

connected.)

Input Signal TMDS (Single Link)
Dimensions

Dimensions (without stand) 337 mm (W) × 441 mm (H) × 78.5 mm (D)

Weight 8.3 kg (18.3 lbs.)
Weight (without stand) 5.3 kg (11.7 lbs.)
Environment Conditions

Temperature

Humidity 30 % to 80 % R.H. Non-condensing

Pressure 860 to 1,060 hPa
USB Standard Rev. 2.0 complied self-powered hub
Communication Speed 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Downstream Power Supply 500 mA for each (Max.)
USB ports Upstream port × 1, Downstream port × 2
Certifications and Standards TÜV Rheinland /GM, CB, NRTL/C-TÜV, CE (93/42/EEC), FCC-A
Classification of Equipment Type of protection against electric shock: Class I

337 mm (W) × 493 ∼ 575 mm (H) × 208.5 mm (D)
(13.3” (W) × 19.4” ∼ 22.6” (H) × 8.2” (D))

(13.3” (W) × 17.4” (H) × 3.09” (D))

Operating: 0 °C ∼ 35 °C (32 °F ∼ 95 °F)
Storage: -20 °C ∼ 60 °C (-4 °F ∼ 140 °F)

EMC class: EN60601-1-2 2001: Group1 Class A
Classification of medical device (MDD 93/42/EEC): Class I

28 8. SPECIFICATIONS

Dimensions

3(0.12)

)
3

.2
(3

2
8

)
6

.

)

2

4

.

2

9

(

1

5

(

7

3

5

9

)

4

7

.
0
1

(
5

.
2
7
2

)
5
0

.
2

(
2
5

337(13.3)

300.8(11.8)

RO TAT

2

1

(

5

.

5

2

3

English

mm (inches)

3(0.12)

)
2
1

.
0

(
3

I

O

N

)

8

.

)

)

8

4

.

.

5

7

1

1

(

(

4

1

.

4

0

4

0
4

)
1
3

.

)
2
1

.
0

(
3

0

(
8

)

9

0

.

3

(

5

.

8

7

)

7

1

.

2

(

5

5

)

6

.

6

(

8

6

1

)

9

.
1
1

(
5

)

.

1

1

)

6

0

6

.

3

2

0

.

(

0

5

(

.

5

5

.

1

6

)

6

0

.

1

(

7

2

)

2

.

8

(

5

.

8

0

2

FRONT

SIDE

Default settings

PowerManager DVI DMPM
Off Timer Disable
Menu Position Center
Menu Off Timer 45 seconds
Orientation Portrait
Signal Selection Monochrome 8bit
Language English

Optional

Calibration Kit EIZO RadiCS GX2

TOP

8. SPECIFICATIONS

29

English

Pin Assignment

DVI-D Connector

3

2

1

10

9

11
19

18 22 23

8

4

7

6

5

12

14 15

16

13

24

20

2117

USB Ports

Upstream

Series B Series A

Pin
No.

Signal Pin

No.

Signal Pin

No.

Signal

1 TMDS Data2- 9 TMDS Data1- 17 TMDS Data0­2 TMDS Data2+ 10 TMDS Data1+ 18 TMDS Data0+
3 TMDS Data2/4

Shield

11 TMDS Data1/3

Shield

19 TMDS Data0/5

Shield
4 NC* 12 NC 20 NC
5 NC 13 NC 21 NC
6 DDC Clock

14 +5V Power 22 TMDS Clock shield

(SCL)
7 DDC Data (SDA) 15 Ground (For +5V) 23 TMDS Clock+
8 Analog Vertical

16 Hot Plug Detect 24 TMDS Clock-

Sync

(*NC: No Connection)

Downstream

No. Signal Signal

1 VCC Cable power
2 - Data Serial data
3 + Data Serial data
4 Ground Cable Ground

30 8. SPECIFICATIONS

9. GLOSSARY

Afterimage

The Afterimage is particular to LCD monitors when the monitor screen is left on for a
long period without use. The “Afterimage” can be removed gradually by changing
the displayed image.

DVI

(Digital Visual Interface)
A digital flat panel interface. DVI can transmit digital data from the PC directly

without loss with the signal transition method “TMDS”.
There are two kinds of DVI connectors. One is DVI-D connector for digital signal

input only. The other is DVI-I connector for both digital and analog signal inputs.

DVI DMPM

(DVI Digital Monitor Power Management)
The Power management system for the digital interface. The “Monitor ON” status

(operation mode) and the “Active Off” status (power-saving mode) are indispensable
for the DVI-DMPM as the monitor’s power mode.

English

LUT

(Look-up table)
Look-up table is the compensation data, to which the monitor refers, when the

monitor outputs the input data from a graphics board. In this model, the “Default*”
adjusted beforehand referring to look-up table at a factory or “Normal”, which is in
the state of the characteristic of panel original, (i.e. not adjusted) can be available.
“Custom” automatically stores the customized data after the calibration is performed.

*“Default” is adjusted with the 500cd/ms brightness to DICOM grayscale standard.

Resolution

The LCD panel consists of a fixed number of pixel elements which are illuminated to
form the screen image. The EIZO G22-BL/G22-CL display panel consists of 1600
horizontal pixels and 1200 vertical pixels. At a resolution of 1600 × 1200, all pixels
are displayed as a full screen.

TMDS

(Transition Minimized Differential Signaling)
A signal transition method for the digital interface.

9. GLOSSARY

31

For U.S.A, Canada, etc. (rated 100-120 Vac) Only

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will required to correct the interference at his own expense.

Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.

Note

Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference
within the limits of a Class A digital device.

- AC Cord

- Shielded Signal Cable (enclosed)

Canadian Notice

This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe A est comforme à la norme NMB-003 du Canada.

For Europe, etc. (rated 200-240 Vac) Only

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.

Warnung

Bey dem gerät handelt es sich um ein Klasse-A-Produkt. Bei Betrieb des Geräts in Wohnumgebungen ist
gegebenenfalls durch entsprechende Maßnahmen dafür zu sorgen, dass eine Störung des Radio- und
Fernsehempfangs vermieden wird.

Avertissement

Cet appareil est de classe A. Il est susceptible de créer des interférences radio dans un environnement
domestique, dans ce cas l’utilisateur devra prendre les mesures appropriées.

Recycle Auskunft

Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland zusammen mit dem
Partner MIREC GmbH & Co. KG. Dort werden die Geräte in ihre Bestandteile zerlegt, die dann der
Wiederverwertung zugeführt werden. Um einen Abholtermin zu vereinbaren und die aktuellen Kosten zu
erfahren, benutzen Sie bitte folgende Rufnummer: 02153-73 35 00. Weitere Informationen finden Sie auch
unter der Internet-Adresse: www.eizo.de.

Recycling Information for customers in Switzerland:

All recycling information is placed in the SWICO’s website.
http://www.swico.ch

Recycling-Information für Kunden in der Schweiz:

Alle Informationen zum Thema Recycling finden Sie auf der Homepage des Brancheverbandes SWICO.
http://www.swico.ch

Renseignements de recyclage pour les clients en Suisse:

Vous trouvez tous les renseignements pour le sujet de recyclage sur la page WEB de I’UNION DE BRAN
CHE SWICO.
http://www.swico.ch

Recycling Information for customers in USA:

All recycling information is placed in the EIZO Nanao Technologies, Inc’s website.
http://www.eizo.com/contact/index.html

Återvinnings information för kunder i Sverige:

All information om återvinning finns på Eizo Europe AB:s hemsida:
www.eizo.se