Eizo flexscan EV2780, FLEXSCAN EV2456 User Manual

Important

Please read PRECAUTIONS, this User’s Manual, and the Setup Guide
(separate volume) carefully to familiarize yourself with safe and
effective usage.

• Please refer to the Setup Guide for basic information ranging from
connection of the monitor to a PC to using the monitor.

• For the latest product information including the User’s Manual, refer
to our web site :

http://www.eizoglobal.com

Color LCD Monitor

User’s Manual

2

Location of Caution Statement

AVERTISSEMENT

WARNING

WARNUNG

This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.

No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.

3

Notice for this monitor

Notice for this monitor

Aside from creating documents, viewing multimedia content, and other general purposes, this product is also
suited to applications such as creating survey maps and other drawings (Assuming usage of approximately
12 hours per day).
If using this product for the following kinds of applications, where an extremely high degree of reliability and
safety is required, then measures should be in place to maintain safety while using this product.

• Transportation equipment (ships, aircraft, trains, and automobiles)

• Safety devices (Disaster prevention systems, security control systems, etc.)

• Life-critical devices (medical devices, such as life-support devices and operating room devices)

• Nuclear energy control devices (Nuclear energy control systems, security control systems of nuclear facilities, etc.)

• Major system communication devices (operation control systems of transportation systems, air trafc control systems,

etc.)

This product has been adjusted specically for use in the region to which it was originally shipped. If the
product is used outside the region, it may not operate as specied in the specications.

This product may not be covered by warranty for uses other than those described in this manual.

The specications noted in this manual are only applicable when the following are used:

• Power cords provided with the product

• Signal cables specied by us

Only use optional products manufactured or specied by us with this product.

If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due to
the composition of the rubber. Check the desk surface before use.

It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after the monitor power has been turned on, and then adjust the monitor.

Monitors should be set to a lower brightness to reduce changes in luminosity caused by long-term use and
maintain a stable display.

When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image for
extended periods of time. Depending on the image, an afterimage may appear even if it was displayed for
a short period of time. To remove such a phenomenon, change the image or keep the power turned off for
several hours.

If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To
maximize the life of the monitor, we recommend the monitor be turned off periodically.

Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime (refer

to “Cleaning” (page 4)).

The LCD panel is manufactured using high-precision technology. Although, missing pixels or lit pixels may
appear on the LCD panel, this is not a malfunction. Percentage of effective dots: 99.9994 % or higher.

The backlight of the LCD panel has a xed lifetime. Depending on the usage pattern, such as usage for
long continuous periods, the lifespan of the backlight may run out sooner, requiring replacement. When the
screen becomes dark or begins to icker, please contact your local EIZO representative.

4

Notice for this monitor

Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage
your panel. (If the pressure marks remain on the panel, leave the monitor with a black or white screen. The
symptom may disappear.)

Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel. Do
not attempt to brush with tissues as this may scratch the panel.

When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage to the
monitor.

Cleaning

Attention

• Chemicals such as alcohol and antiseptic solution may cause gloss variation, tarnishing, and fading of the cabinet
or panel, and also quality deterioration of the image.

• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.

Note

• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.

The stains on the cabinet and panel surface can be removed by moistening part of a soft cloth with water.

To use the monitor comfortably

• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.

• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.

5

CONTENTS

CONTENTS

Notice for this monitor ......................................... 3

Cleaning .................................................................... 4

To use the monitor comfortably ............................. 4

CONTENTS ............................................................. 5

Chapter 1 Introduction ....................................... 6

1-1. Features ......................................................... 6

1-2. Controls and Functions ............................... 9

1-3. Supported Resolutions ...............................11

1-4. Setting the Resolution ................................12

Chapter 2 Basic Adjustment/Setting .............. 13

2-1. Switch Operation Method ...........................13

2-2. Switching Input Signals ..............................14

2-3.

Switching Display Modes (Color Modes)

...15

2-4. Conserving Energy ...................................... 15

2-5. Adjusting Brightness ..................................17

2-6. Adjusting Volume.........................................17

Chapter 3 Advanced Adjustment/Setting ...... 18

3-1. Basic Operation of the Setting menu ........18

3-2. Setting Menu Functions ..............................19

Chapter 4 Administrator Settings ................... 26

4-1. Basic Operation of the “Administrator

Settings” Menu ............................................ 26

4-2. Functions of the “Administrator

Settings” Menu ............................................ 27

Chapter 5 Troubleshooting ..............................29

5-1. No Picture .................................................... 29

5-2. Imaging Problems ...................................... 30

5-3. Other Problems ........................................... 32

Chapter 6 Reference ........................................ 33

6-1. Attaching the Optional Arm ....................... 33

6-2. Detaching / Attaching Stand Base ............ 35

6-3. Attaching / Detaching the Cable Holder ....37

6-4. Connecting Multiple PCs ........................... 38

6-5. Using the USB Hub Function ..................... 39

6-6. Specications ............................................. 40

Chapter 7 Glossary .......................................... 42

Appendix .............................................................. 43

Trademark ............................................................... 43

License ................................................................... 43

ENERGY STAR ........................................................ 43

TCO .......................................................................... 43

FCC Declaration of Conformity ............................ 45

LIMITED WARRANTY ............................................. 46

Recycling Information ............................................47

6

Chapter 1 Introduction

Chapter 1 Introduction

Thank you very much for choosing an EIZO color LCD monitor.

1-1. Features

●

Support for DisplayPort over USB Type-C (DP Alt Mode) / USB
Power Delivery

Support for DisplayPort over USB Type-C (DP Alt Mode) / USB Power Delivery

• Support for DisplayPort over USB Type-C (DP Alt Mode) / USB Power Delivery

Power Supply

Video Signals

• While displaying photos and motion pictures from a smartphone or tablet, this product can charge
the device.

100%

Video Signals

Power Supply

Note

• Devices to be connected must be equipped with a USB-C connector, and support the charging function
based on USB-C or USB Power Delivery.

7

Chapter 1 Introduction

●

High Degree of Flexibility for Installation

• This product can be used as an external monitor of a notebook computer.

• This product can be used in a multi-monitor conguration in which multiple monitors are connected

to a single PC.

• Mounting the monitor on an arm enables this product to be used in a multiple-monitor conguration
in which the screen is rotated by 180° (ipped vertically).

Note

• PC settings must be congured to rotate the monitor display by 180°.

8

Chapter 1 Introduction

●

Reduction of Power Consumption

This product provides a function that automatically adjusts the screen brightness to reduce power
consumption *1. Power Reduction, CO2 Reduction, and Eco Performance Level can be checked on
the "EcoView Settings" menu.

• Auto EcoView
The ambient light sensor on the front of the monitor detects the ambient brightness to automatically
adjust the screen brightness to a comfortable level.

• EcoView Optimizer 2
The monitor automatically adjusts the screen brightness according to the white level of the input
signal. This function can reduce power consumption while maintaining the brightness specied by
the input signal.

*1 Reference values:

Maximum power consumption: 96 W (when a USB device is connected, speaker working), standard power
consumption: 23 W (brightness 120 cd/m

2

, when no USB device is connected, speaker not working, at

default settings)

●

Realizing More Convenient Operations Using Screen InStyle

The "Screen InStyle" monitor control utility enables you to use the monitor more conveniently.

• The monitor color mode can be switched automatically to suit the software to be used.

• When multiple monitors are installed, you can turn the power on and off or change the color mode

of all monitors at the same time.

Note

• Screen InStyle can be downloaded from our web site (http://www.eizoglobal.com).

• The Windows operating systems are only supported.

9

Chapter 1 Introduction

1-2. Controls and Functions

●

Front

Setting menu

*1

3 42

1

1. Ambient light sensor Detects ambient brightness (Auto EcoView function (page 16)).

2. Operation switches Displays menus. Operate the switches according to the operation guide.

3. Power switch Turns the power on or off.

4. Power indicator Indicates the monitor’s operation status.

White: Screen display
Orange: Power saving mode
OFF: Main power / power off

*1 For details on usage, see “3-1. Basic Operation of the Setting menu” (page 18).

10

Chapter 1 Introduction

●

Rear

6

5

14

13

7 7

11

12

8 9 10

5. Handle This handle is used for transportation

6. Security lock slot Complies with Kensington’s MicroSaver security system.

7. Speakers Outputs audio.

8. Main power switch

Turns the main power on or off.

: On, : Off

9. Power connector Connects the power cord.

10. Input signal connectors The following connectors are available on the monitor rear in order of left

to right.
HDMI connector
DisplayPort connector
USB-C connector

11. USB downstream port Connects to a peripheral USB device.

12. Headphone jack Connects to headphones.

13. Stand

*2

Adjusts the height and angle (tilt, swivel, and rotation) of the monitor.

14. Cable holder

*3

Holds the monitor cables.

*2 An optional arm (or optional stand) can be attached by removing the stand section (see “6-1. Attaching

the Optional Arm” (page 33)).

*3 For details on mounting the cable holder, see “6-3. Attaching / Detaching the Cable Holder” (page 37).

11

Chapter 1 Introduction

1-3. Supported Resolutions

The monitor supports the following resolutions.

Resolution

Applicable

Signals

Vertical Scan

Frequency

DisplayPort HDMI

USB-C

Single

screen

display

PbyP

display

*

1

Single

screen

display

PbyP

display

*

1

Single

screen

display

PbyP

display

*

1

640×480

VGA / CEA-861

59.94 Hz

√ √ √ √ √ √

640×480 CEA- 861 60 Hz

√ √ √ √ √ √

720×400 VGA TEXT 70.09 Hz

√ √ √ √ √ √

720×480 CEA-861

59.94 Hz / 60 Hz

√ √ √ √ √ √

720×576 CEA-861 50 Hz

- - √ √ - -

800×600 VESA 60.32 Hz

√ √ √ √ √ √

1024×76 8 VESA 60 Hz

√ √ √ √ √ √

1280 ×720 VESA CVT 59.86 Hz

√ √ √ √ √ √

1280 ×720

VESA CVT RB

59.98 Hz

√ √ √ √ √ √

1280 ×720 CEA-861 50 Hz

- - √ √ - -

1280 ×720 CEA-861

59.94 Hz / 60 Hz

√ √ √ √ √ √

1280×800 VESA CVT 59.81 Hz

√ √ √ √ √ √

1280×1024 VESA 60.02 Hz

√ √ √ √ √ √

1280×1440

VESA CVT RB

59.9 Hz

- √

*

2

- √

*

2

- √

*

2

1600×900 VESA RB 60 Hz

√ - √ - √ -

1600×1200 VESA 60 Hz

√ - √ - √ -

1680×1050 VESA CVT 59.95 Hz

√ - √ - √ -

1680×1050

VESA CVT RB

59.88 Hz

√ - √ - √ -

1920×1080 CEA-861 50 Hz

- - √ - - -

1920×1080 CEA-861

59.94 Hz / 60 Hz

√ - √ - √ -

1920×1200 VESA CVT 59.89 Hz

√ - √ - √ -

1920×1200

VESA CVT RB

59.95 Hz

√ - √ - √ -

2560×1440 VESA CVT 29.94 Hz

- - √ - √ -

2560×1440 VESA CVT RB 59.95 Hz

√

*

2

- √

*

2

- √

*

2

-

*1 Only when “Auto PbyP Resolution” is “On”
*2 Recommended resolution

Note

• Only the progressive scan type is supported.

12

Chapter 1 Introduction

1-4. Setting the Resolution

If the resolution is incorrect after connecting the monitor to a PC or if you want to change the resolution,
follow the procedure below.

●

Windows 10

1. Right-click the mouse anywhere on the desktop except on icons.

2. From the displayed menu, click “Display Settings”.

3. On the "Customize your display" dialog box, click "Advanced display settings".

4. Select a monitor, then choose a resolution from the "Resolution" pull-down menu.

5. Click the "Apply" button.

6. When a conrmation dialog box is displayed, click “Keep changes”.

●

Windows 8.1 / Windows 7

1. For Windows 8.1, click the "Desktop" tile on the Start Screen to display the desktop.

2. Right-click the mouse anywhere on the desktop except on icons.

3. From the displayed menu, click “Screen resolution”.

4. Select a monitor, then choose a resolution from the "Resolution" pull-down menu.

5. Click the "OK" button.

6. When a conrmation dialog box is displayed, click “Keep changes”.

●

OS X Mountain Lion (10.8) or later

1. Select “System Preferences” from the Apple menu.

2. When the “System Preferences” dialog box is displayed, click “Displays”. (For Mac OS X 10.8,
click "Displays" for "Hardware".)

3. On the displayed dialog box, select the “Display” tab, then choose "Change" for “Resolutions”.

4. The list of selectable resolutions is displayed. Select the desired resolution. If the desired
resolution is not displayed in the list, hold down the Option key and select "Change".

5. Your selection will be reected immediately. When you are satised with the selected resolution,
close the window.

●

Mac OS X 10.7

1. Select “System Preferences” from the Apple menu.

2. When the “System Preferences” dialog box is displayed, click “Displays” for “Hardware”.

3. On the displayed dialog box, select the “Display” tab and select the desired resolution in the
“Resolutions” eld.

4. Your selection will be reected immediately. If you are satised with the selected resolution, close
the window.

13

Chapter 2 Basic Adjustment/Setting

Chapter 2 Basic Adjustment/Setting

This product enables users to change the brightness according to personal preference or to suit the usage
environment and reduce power consumption to conserve energy.

This chapter describes the basic functions that can be adjusted and set using the switches on the front of the
monitor.
For advanced adjustment and setting procedures using the Setting menu, see “Chapter 3 Advanced

Adjustment/Setting” (page 18).

2-1. Switch Operation Method

1.

Displaying the operation guide

1. Touch any switch (except ).

The operation guide appears on the screen.

2.

Adjusting/setting

1. Touch a switch for adjustment/setting.

The Adjustment/Setting menu appears.
(A submenu may also be displayed. In this case, select the item for adjustment/setting using

and

select

.)

2. Perform adjustment/setting with the switches and select to accept the changes.

3.

Exiting

1. Select to exit the menu.

2. When no menu is displayed, the operation guide will automatically disappear after a few seconds
if no switches are operated.

14

Chapter 2 Basic Adjustment/Setting

2-2. Switching Input Signals

When a monitor has multiple signal inputs, the signal to display on-screen can be changed.

Note

• By selecting PbyP (Picture by Picture) display when a monitor has multiple input signals, windows can be
displayed side-by-side.
Because 2 windows can be displayed on a single monitor, the need for changing between signals is eliminated,
which leads to increased work efciency.
By selecting PbyP display, the combination of the signals to display on the left and right windows can be
switched.

PbyP display image

A B

15

Chapter 2 Basic Adjustment/Setting

2-3. Switching Display Modes (Color Modes)

This product is preinstalled with color modes for various display purposes.
Switch the mode according to the purpose and content for display. This allows the monitor to display
images in a manner appropriate to the display content.

●

Display Modes

Color Mode Purpose

User1
User2

Select either of these modes to set a user-dened display mode.

sRGB

This mode is suitable for matching color reproduction with peripheral devices that
support sRGB, such as when printing photos taken using a digital camera.

Paper

This mode uses color tones and contrast similar to that of paper to produce a printed
paper effect. It is suitable for displaying images from media such as books and
documents.

Movie

This mode displays moving images brightly and with a clear-cut three-dimensional
appearance. It is suitable for playing back video content.

Note

• “Screen InStyle” allows you to select the color mode automatically according to the software in use.

• In Paper mode, the amount of blue light emitted from the screen is reduced by changing the color tone and

controlling the brightness.

• During PbyP display, you can set the color mode for each of the “Left” and “Right” screens.

2-4. Conserving Energy

This monitor is equipped with EcoView functions to enable users to conserve energy.
Use this function to curtail unnecessary power consumption and save on electricity expenses. Saving
power also reduces carbon dioxide emissions.

16

Chapter 2 Basic Adjustment/Setting

Note

• The power saving level (Power Reduction, CO2 Reduction, and Eco Performance Level) can be checked on the
“EcoView Settings” menu. The more indicators that light up representing the Eco Performance Level, the higher
the power saving level attained.

- Power Reduction: the reduction in the backlight’s power consumption as a result of the adjusted brightness
value.

- CO

2

Reduction: converted from the “Power Reduction” value, this is an estimate of the quantity of CO2

emissions reduced when using the monitor for 1 hour.

• The numeric value is a result of calculation based on a default setting (0.000555t-CO2/kWh) determined by a
Japanese ministerial ordinance (2006, Ministry of Economy, Trade and Industry, Ministry of Environment, civil
code article 3) and may differ depending on country and year.

Function

Setting

Range

Description

Auto EcoView

On
Off

The ambient light sensor on the front of the monitor detects
the ambient brightness to automatically adjust the screen
brightness to a comfortable level using Auto EcoView. The
power consumption of the backlight can be curtailed by
adjusting the brightness to an appropriate level.
This function can also mitigate eye strain and tiredness
caused by a screen that is too bright or too dark.

Use the “Advanced Settings” to set the automatic adjustment
range to suit the monitor’s usage environment or personal
preference.

Note

• Be careful not to block the ambient light sensor on the
lower side of the monitor when using Auto EcoView.

• Even when the Auto EcoView setting is “On”, the
operation switch on the front of the monitor or color
adjustment can be used to change the “Brightness” to
suit your personal preference. Moreover, the manner in
which the Auto EcoView function changes brightness
also differs according to the changed value.

Advanced
Settings

Maximum
Minimum

Brightness 0 to 100

Set the range for automatic brightness adjustment.
By setting the maximum value and minimum value of the
adjustment range in advance, the brightness will be adjusted
automatically within the set range.

Note

• The maximum and minimum brightness values cannot
be set to the same value.

Ambient
Light

Bright

Standard

Dark

Using the default setting is recommended.
(Default setting: “Bright” for maximum value, “Dark” for
minimum value)

Note

• For details on the “Ambient Light” setting, refer to our
web site (http://www.eizoglobal.com).

Reset - Return the advanced settings to their default values.

17

Chapter 2 Basic Adjustment/Setting

Function

Setting

Range

Description

EcoView Optimizer 2

On
Off

The monitor automatically adjusts the screen brightness
according to the white level of the input signal.
This function can reduce power consumption while
maintaining the brightness specied by the input signal.

Note

• The setting is turned “Off” in the following cases:

- When “sRGB” or “Movie” is selected for the color

mode

- During PbyP display

• When set to “On”, the appearance of pale colors may

change. If this bothers you, set this function to “Off”.

2-5. Adjusting Brightness

The brightness of the screen can be adjusted to suit the installation environment or personal preference.
The screen brightness is adjusted by changing the brightness of the backlight (light source from the LCD
back panel).

Setting Range

0 to 100

Note

• When Auto EcoView is set to “On”, the adjustment range is restricted as follows. (For details on Auto EcoView,
see “Auto EcoView” (page 16).)

- The brightness setting cannot be increased or decreased past the maximum and minimum brightness values

specied in the advanced settings of Auto EcoView.

- Brightness may not be adjusted when the installation environment of the monitor is excessively bright or dark.

• The screen brightness is restricted when “USB Power Delivery” is set to “30W” “USB Power Delivery” (page

24).

2-6. Adjusting Volume

The volume of the speakers and headphones can be set individually.

Setting Range

0 to 30

18

Chapter 3 Advanced Adjustment/Setting

Chapter 3 Advanced Adjustment/Setting

This chapter describes the advanced monitor adjustment and setting procedures using the Setting menu.
For basic functions, see “Chapter 2 Basic Adjustment/Setting” (page 13).

3-1. Basic Operation of the Setting menu

1.

Menu display

1. Touch any switch (except ).

The operation guide appears.

2. Select .

The Setting menu appears.

2.

Adjusting/setting

1. Select a menu to adjust/set with and select .

The Sub menu appears.

2. Select an item to adjust/set with and select .

The Adjustment/Setting menu appears.

3. Perform adjustment/setting with or and select to accept the changes.

The Sub menu appears.
Selecting

during adjustment/setting will cancel the adjustment/setting and restore the state prior to

making changes.

3.

Exiting

1. Selecting several times will terminate the Setting menu.

19

Chapter 3 Advanced Adjustment/Setting

3-2. Setting Menu Functions

●

Color Adjustment

The color mode setting status can be adjusted according to personal preference.

Functions that can be adjusted differ depending on the color mode.

√: Adjustable -: Not adjustable

Function

Color Mode

User1
User2

sRGB Paper Movie

Brightness √ √ √ √
Contrast √ - - √
Temperature √ - √ √
Gamma √ - - -

Super Resolution √ - √ √
Advanced

Settings

Overdrive √ - - -

Hue √ - - √
Saturation √ - - √
Gain √ - - -

Reset √ √ √ √

Attention

• It takes about 30 minutes for the performance of electrical parts to stabilize. Please wait 30 minutes or more
after power to the monitor has been turned on before adjusting the monitor.

• The same image may be observed in different colors on multiple monitors due to monitor-specic
characteristics. Make ne color adjustments visually when matching colors across multiple monitors.

Function Setting Range Description

Window Selection Left

Right
All

Select the application range for each setting of the color
adjustment.
When using PbyP display, select this range rst.

• “Left”
The setting is applied only to the left screen.

• “Right”
The setting is applied only to the right screen.

• “All”
The setting will be applied to both the left and right
screens.

Note

• Enabled only during PbyP display.

• For details on PbyP, see “2-2. Switching Input Signals”

(page 14).

20

Chapter 3 Advanced Adjustment/Setting

Function Setting Range Description

Color Mode User1

User2
sRGB

Paper

Movie

Select the desired mode according to the monitor
application.

The color setting status can also be adjusted according to
personal preference. Select the mode for adjustment and
perform adjustment using the relevant functions.

Note

• For details on the adjustment status of each mode, see

“2-3. Switching Display Modes (Color Modes)” (page

15).

Brightness 0 to 100

The screen brightness is adjusted by changing the
brightness of the backlight (light source from the LCD back
panel).

Note

• If the image is too dark even when the brightness is set
to 100, adjust the contrast.

Contrast 0 to 100

The brightness of the screen is adjusted by varying the video
signal level.

Note

• A contrast of 50 displays every color gradation.

• When adjusting the monitor, it is recommended to

perform brightness adjustment, which does not lose
gradation characteristics, prior to contrast adjustment.

• Perform contrast adjustment in the following cases.

- If the image is too dark even when the brightness is

set to 100 (Set the contrast to higher than 50.)

Temperature

Off
4000 K to 10000 K
(in increments of
5

00 K. 9300 K is

included.)

Adjust the color temperature.
The color temperature is normally used to express the hue of
“White” and/or “Black” with a numerical value. The value is
expressed in degrees “K” (Kelvin).
The screen becomes reddish at low color temperatures and
bluish at high color temperatures, similar to the temperatures
of a ame. A gain preset value is set for each color
temperature setting value.

Note

• The value shown in “K” is available only as a reference.

• “Gain” allows you to perform more advanced adjustment.

• If set to “Off”, the image is displayed in the preset color

of the monitor (Gain: 100 for each RGB channel).

• When the gain is changed, the color temperature setting
changes to “Off”.

Gamma 1.8

2.0

2.2

2.4

Adjust the gamma.
While the brightness of the monitor varies depending on the
input signal, the variation rate is not proportional to the input
signal. Maintaining the balance between the input signal
and brightness of the monitor is referred to as “Gamma
correction”.

Note

• If “sRGB” is selected for the color mode, the gamma
value is xed to “2.2”.

• If “Paper” is selected for the color mode, “Paper” is
displayed for the gamma value.

Super Resolution Standard

Low
Off

Image blur can be reduced by enhancing its outline.

21

Chapter 3 Advanced Adjustment/Setting

Function Setting Range Description

Advanced
Settings

Overdrive Enhanced

Standard

Off

This function allows you to set the overdrive intensity based
on the use of the monitor.
Image lag can be reduced by using the “Enhanced” setting
when displaying moving images.

Hue -50 to 50

Adjust the hue.

Note

• Using this function may prevent some color gradations
from being able to be displayed.

Saturation -50 to 50

Adjust the color saturation.

Note

• Using this function may prevent some color gradations
from being able to be displayed.

• The minimum value (-50) changes the screen to
monochrome.

Gain 0 to 100

The brightness of each red, green, and blue color component
is referred to as “Gain”. The hue of “white” can be changed
by adjusting the gain.

Note

• Using this function may prevent some color gradations
from being able to be displayed.

• The gain value changes according to the color
temperature.

• When the gain is changed, the color temperature setting
changes to “Off”.

Reset - Reset any color adjustments for the currently selected color

mode back to the default settings.

22

Chapter 3 Advanced Adjustment/Setting

●

Signal Settings

Set the method for outputting the signal input from the PC to the monitor.

Function Setting Range Description

Window Selection Left

Right

Select the application range for the signal settings.
When using PbyP display, select this range rst.

• “Left”
The setting is applied to the left screen.

• “Right”
The setting is applied to the right screen.

Note

• Enabled only during PbyP display.

• For details on PbyP, see “2-2. Switching Input

Signals” (page 14).

Picture Expansion Auto

*1

Full Screen
Aspect Ratio
Dot by Dot

The screen size of the monitor display can be changed.

• “Auto” The monitor automatically changes the
screen size according to the aspect ratio and
resolution information from the PC.

• “Full Screen” Images are stretched to full screen.
Since aspect ratios are not maintained, images
may be distorted in some cases.

• “Aspect Ratio” Images are enlarged to full screen
without changing the aspect ratio. Since aspect
ratios are maintained, blank horizontal or vertical
borders may appear.

• “Dot by Dot” Displays the image at the set
resolution or size specied by the input signal.

Note

• Example settings

- Full Screen

- Aspect Ratio

- Dot by Dot

*1 Only enabled when input signal information according to which the setting can be automatically

determined is detected during HDMI input

23

Chapter 3 Advanced Adjustment/Setting

Function Setting Range Description

Input Color Format Auto

*2

YUV 4:2:2

*3

YUV 4:4:4

*3

YUV

*4

RGB

The color format of the input signal can be specied.
Try changing this setting if colors are not displayed
correctly.

Note

• This setting is required when a DVI device is
connected to the monitor via the HDMI connector
port using a DVI-HDMI conversion connector.

*2 Only enabled when input signal information according to which the setting can be automatically

determined is detected
*3 Only enabled during HDMI input
*4 Only enabled during DisplayPort input or USB-C input

Function Setting Range Description

Input Range Auto

Full
Limited

Depending on the PC, black and white of the video
level of the signal output to the monitor may be limited.
If a limited signal is displayed on the monitor, black
will appear faint and white will appear dull, leading to a
reduction in contrast. The output range of such signals
can be extended to match the actual contrast ratio of
the monitor.

• “Auto” Automatically identies the brightness
range of the input signal and displays the image
accordingly.

• “Full” Extension of the signal output range is not
performed.

• “Limited” Extends the signal output range through
0 to 255 and displays the image.

●

Preference Settings

The monitor’s settings can be congured to suit the usage environment or personal preference.

Function Setting Range Description

Menu Rotation 0°

90°
270°

Change the orientation of the Setting menu when using the monitor
screen in the portrait display position.

Note

• Make sure that the cables are correctly connected.

• PC settings must be congured to use the monitor in a portrait

position. For details, refer to our web site. (http://www.eizoglobal.

com).

• The menu cannot be rotated by 180˚. To install the monitor rotated
by 180˚, perform monitor adjustment/settings before rotating the
monitor.

24

Chapter 3 Advanced Adjustment/Setting

Function Setting Range Description

Power Save On

Off

The monitor can be set to enter power saving mode according to the
state of the PC.
The monitor changes to power saving mode about 15 seconds after
signal input ceases to be detected.
When the monitor has shifted to power saving mode, images are not
displayed on the screen.

• Exiting power saving mode

- If the monitor receives input, it automatically exits power saving

mode and returns to the normal display mode.

Note

• At the time of shifting to power saving mode, a message that
indicates the transition is displayed 5 seconds in advance.

• During PbyP display, the monitor only enters power saving mode
after both PCs have entered power saving mode or have been
switched off.

• When not using the monitor, you can turn off the main power supply
or disconnect the power plug so that the power is cut completely.

• When the monitor is in power saving mode, devices connected to the
USB downstream port will still work. Therefore, power consumption
of the monitor varies with connected devices even in power saving
mode.

Power Indicator On

Off

The power indicator (white) can be turned off during screen display.

Sound Selection
(PbyP)

Left
Right

Select the source of audio to output from the monitor during PbyP
display.

• “Left”
Outputs the audio source from the left screen.

• “Right”
Outputs the audio source from the right screen.

USB Power
Delivery

15W

30W

The supply wattage setting can be changed.

• “15W”
Prioritizes the screen brightness. The power supplied by USB Power
Delivery is restricted to 15 W.

• “30W”
Prioritizes the power supplied by USB Power Delivery. The screen
brightness is restricted.

Note

• The device may not be supplied with power or charged depending on
the prole (voltage or current) supported by the connected device.

- This monitor supports the following proles:
“15W” : 5 V / 3 A
“30W” : 5 V / 3A, 9 V / 3 A, 12 V / 2.5 A, 15 V / 2 A, 20 V / 1.5 A

• The screen disappears temporarily when you have changed the
setting, but it returns to normal after a few seconds.

• When you change the setting, remove any peripherals such as
a USB memory device connected to the downstream port of the
monitor.

Monitor Reset -

Restore all settings to their default values except for the following
settings.

• PbyP Picture Setup

• “USB Power Delivery” setup

• Settings on the “Administrator Settings” menu

Note

• For details on default settings, see “Main Default Settings” (page

41).

25

Chapter 3 Advanced Adjustment/Setting

●

Language

The display language for menus and messages can be selected.

Setting Range

English, Deutsch, Français, Español, Italiano, Svenska, Japanese, Simplied Chinese, Traditional
Chinese

Attention

• The display language of the “Administrator Settings” menu cannot be changed.

●

Information

Monitor information (product name, serial number, usage time, resolution, and input signal) can be
checked.

Example: • Single screen display • PbyP display

26

Chapter 4 Administrator Settings

Chapter 4 Administrator Settings

This chapter describes how to congure monitor operation using the “Administrator Settings” menu.
This menu is for administrators. Conguration on this menu is not required for normal monitor use.

4-1.

Basic Operation of the “Administrator Settings” Menu

1.

Menu display

1. Touch to turn off the monitor.

2. While touching the leftmost switch, touch

for more than 2 seconds to turn on the monitor.

The “Administrator Settings” menu appears.

2.

Setting

1. Select an item to set with and select .

The Adjustment/Setting menu appears.

2. Set with and select .

The “Administrator Settings” menu appears.

3.

Applying and exiting

1. Select “Apply” and then .

The settings are applied and the “Administrator Settings” menu exits.

Attention

• The language (English) of the “Administrator Settings” menu cannot be changed.

27

Chapter 4 Administrator Settings

4-2. Functions of the “Administrator Settings” Menu

Function Setting Range Description

Auto Input Detection On

Off

This function automatically recognizes the connector through
which PC signals are input, and displays images on the screen
accordingly.

• “On”
When the monitor is connected to multiple PCs, if a specic
PC enters power saving mode or no signals are input to the
monitor, the connector is automatically changed to another
one to which signals are input.

• “Off”
This function displays the signal from the selected connector
regardless of whether a signal is input or not. In this case,

you can select the input signal to display using the
operation switch on the front of the monitor. For details, see

“2-2. Switching Input Signals” (page 14).

Note

• This function is not available during PbyP display.

• This product automatically recognizes the connector through

which PC signals are input, and displays images on the
screen accordingly regardless of whether this function is set
to On or Off just after the main power switch on the rear side
of the monitor has been turned on.

• When this function is set to “On”, the monitor only enters
power saving mode after all connected PCs have entered
power saving mode or have been switched off.

Compatibility Mode On

Off

If you want to avoid the following phenomena, set this function to
“On”.

• The positions of windows and icons are shifted when the
monitor is turned off / on or has returned from the power
saving mode.

• Power Save function of the PC does not work normally.

• During USB-C input, the screen blinks two or three times

immediately after the USB cable has been connected or the
PC has returned from the Power Save mode.

• When the power to the monitor is turned off, a device
connected to the USB downstream port does not work.

USB-C Display Mode Normal

Extra

If no image appears on the monitor screen even when a device
compatible with DP Alt Mode is connected to the USB-C
connector of the monitor, set this function to “Extra”.

28

Chapter 4 Administrator Settings

Function Setting Range Description

Auto PbyP Resolution On

Off

This product automatically changes the resolution according to
the screen layout when changing to PbyP display.
Set this function to “Off” to prevent the resolution from changing
automatically when changing to PbyP display. In this case,
change the resolution manually.

Note

• If the resolution does not change correctly during PbyP
display, it is recommended to change this setting to “Off”.

On-Screen Logo On

Off

When the monitor is turned on, the EIZO logo appears on the
screen.
When this function is set to “Off”, the EIZO logo does not appear.

Key Lock Off

Menu

All

In order to prevent changes to settings, the operation switches on
the front of the monitor can be locked.

• “Off”

Enable all switches.

• “Menu”

Lock the

switch.

• “All”

Lock all switches except the power switch.

29

Chapter 5 Troubleshooting

Chapter 5 Troubleshooting

5-1. No Picture

Problem Possible cause and remedy

1. No picture

• Power indicator does not light up.

• Check whether the power cord is connected properly.

• Turn on the main power switch on the rear side of the monitor.

• To u c h

.

• Turn off the main power switch on the rear side of the monitor,
and then turn it on again a few minutes later.

• Power indicator is lighting white. • Increase “Brightness”, “Contrast”, or “Gain” in the Setting menu
(see “Color Adjustment” (page 19)).

• Power indicator is lighting orange. • Switch the input signal.

• Move the mouse or press any key on the keyboard.

• Check whether the PC is turned on.

• Turn off the main power switch on the rear side of the monitor,

and then turn it on again.

• Power indicator is ashing orange and

white.

• This symptom may occur during DisplayPort input.

- Use a signal cable recommended by us for the connection.

Turn the monitor off and on.

• This symptom may occur during USB-C input.

- Disconnect and connect the USB cable.

- Turn off the main power switch on the rear side of the

monitor, and then turn it on again.

2. The message below appears. This message appears when the signal is not input correctly even
though the monitor is functioning properly.

• This message appears when no signal is
input.

Example:

• The message shown left may appear, because some PCs do
not output the signal immediately after power-on.

• Check whether the PC is turned on.

• Check whether the signal cable is connected properly.

• Switch the input signal.

• Turn off the main power switch on the rear side of the monitor,

and then turn it on again.

• The message shows that the input signal
is out of the specied frequency range.

Example:

• Check whether the PC is congured to meet the resolution and
vertical scan frequency requirements of the monitor (see “1-3.

Supported Resolutions” (page 11)).

• Reboot the PC.

• Select an appropriate setting using the graphics board’s utility.

Refer to the User’s Manual of the graphics board for details.

• This message shows that a device that
is not compatible with DP Alt Mode is
connected to the USB-C connector.

Example:

• Check whether a signal cable recommended by us is used.

• Check whether the connected device is compatible with DP Alt

Mode. Contact the device manufacturer for information about
compatibility with DP Alt Mode.

30

Chapter 5 Troubleshooting

5-2. Imaging Problems

Problem Possible cause and remedy

1. The screen is too bright or too dark. • Use “Brightness” or “Contrast” in the Setting menu to

adjust it (see “Color Adjustment” (page 19)). (The LCD
monitor backlight has a limited life span. If the screen
becomes dark or begins to icker, contact your local EIZO
representative.)

• If the screen is too bright, try changing the Auto EcoView
setting to “On”. The monitor detects the ambient
brightness to adjust the screen brightness automatically
(see “Auto EcoView” (page 16)).

2. “Brightness” cannot be adjusted When Auto EcoView is set to “On”, “Brightness” may not be
adjustable due to the advanced settings of Auto EcoView.

• Cannot increase/decrease setting value (“

”

or “

” is displayed in gray)

- “Brightness” adjustment menu via
operation switch

/

- “Brightness” adjustment menu in color
adjustment

/

• The bright adjustment range of the Auto EcoView function
can be limited to ensure that the screen is neither too
bright nor too dark. When the adjustment range is limited,
values outside the range cannot be set. If you want to
set a value outside the range, try changing the following
settings.

- Change the maximum and minimum values for
“Brightness” in the Auto EcoView advanced settings.

- Set Auto EcoView to “Off”.

For details on Auto EcoView settings, see “Auto EcoView”

(page 16).

• Cannot increase/decrease setting value (“

”

and “

” are displayed in gray)

- “Brightness” adjustment menu via
operation switch

- “Brightness” adjustment menu in color
adjustment

• Brightness adjustment may not be possible when the
installation environment of the monitor is excessively
bright or dark. In this case, try changing the following
settings.

- Change the maximum and minimum values for “Ambient
Light” in the Auto EcoView advanced settings.

- Set Auto EcoView to “Off”.

For details on Auto EcoView settings, see “Auto EcoView”

(page 16).

3. Text is blurred

• Check whether the PC is congured to meet the resolution
and vertical scan frequency requirements of the monitor
(see “1-3. Supported Resolutions” (page 11)).

4. Afterimages appear • Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.

• Use the screen saver or power saving function to avoid
displaying the same image for extended periods of time.
Depending on the image, an afterimage may appear even
if it was displayed for a short period of time. To remove
such a phenomenon, change the image or keep the power
turned off for several hours.

5. Green / red / blue / white dots or dark dots
remain on the screen.

• This is due to LCD panel characteristics and not a
malfunction.

6. Interference patterns or pressure marks
remain on the screen.

• Leave the monitor with a white or black screen. The
symptom may disappear.

7. Noise appears on the screen. • In the Setting menu, set “Overdrive” to “Off” (see

“Overdrive” (page 21)).

• When inputting HDCP system signals, normal images
may not be displayed immediately.

31

Chapter 5 Troubleshooting

Problem Possible cause and remedy

8. When you switch the power back on or
return from power save mode, windows or
icons may have shifted position.

• Set the “Compatibility Mode” setting to “On” using one of
the following methods.

- Change the setting using the operation switch on the
front of the monitor.

1. Turn on the monitor.

2. When the operation guide is not displayed, touch the

leftmost switch for more than 3 seconds.
Each time an operation is executed, the setting
changes between On/Off.
(When the setting changes, “Compatibility Mode
: On” / “Compatibility Mode : Off” is displayed on
screen.)

- Change the setting for “Compatibility Mode” on the
“Administrator Settings” menu (see “Compatibility Mode”

(page 27)).

9. The color shown on the screen is not
correct.

• Try changing “Input Color Format” in the Setting menu (see

“Input Color Format” (page 23)).

10. The image does not display on the entire
screen.

• Try changing “Picture Expansion” in the Setting menu (see

“Picture Expansion” (page 22)).

11. The screen does not become brighter even
when “Brightness” is adjusted.

• The screen brightness is restricted when “USB Power
Delivery” is set to “30W”. In this case, set “USB Power
Delivery” to “15W”. (see “USB Power Delivery” (page

24)).

32

Chapter 5 Troubleshooting

5-3. Other Problems

Problem Possible cause and remedy

1. The Setting menu does not appear. • Check whether the switch operation lock function is active

(see “Key Lock” (page 28)).

2. No audio output. • Check whether volume is set to 0.

• Check the PC and audio playback software to see

whether they are congured correctly.

• Check the “Sound Selection (PbyP)” setting during PbyP
display (see “Sound Selection (PbyP)” (page 24)).

3. USB devices connected to the monitor do
not work.

• Check whether the USB cable is correctly connected
between the PC and the monitor. (see “6-5. Using the

USB Hub Function” (page 39)).

• Check whether the USB cable is correctly connected
between the peripheral and the monitor.

• Try using a different USB port on the monitor.

• Try using a different USB port on the PC.

• Reboot the PC.

• If the peripheral devices work correctly when they are

directly connected to the PC, contact your local EIZO
representative.

• Depending on the USB 3.1 host controller that you are
using, connected USB devices may not be recognized
correctly. Update to the latest USB 3.1 driver provided by
each manufacturer, or connect the monitor to the USB 2.0
port.

• Check the PC’s BIOS setting for USB when using
Windows. (Refer to the manual of the PC for details.)

4. Powerindicatorisashingorangeand
white.

• This symptom may occur when the PC is connected
to the DisplayPort connector. Use a signal cable
recommended by us for the connection. Turn the monitor
off and on.

• Check the connection and condition of the USB devices
connected to the monitor.

• Turn off the main power switch on the rear side of the
monitor, and then turn it on again.

5. Power Save function of the PC does not
work normally.

• Set the “Compatibility Mode” setting to “On” using one of
the following methods.

- Change the setting using the operation switch on the
front of the monitor.

1. Turn on the monitor.

2. When the operation guide is not displayed, touch the

leftmost switch for more than 3 seconds.
Each time an operation is executed, the setting
changes between On/Off.
(When the setting changes, “Compatibility Mode
: On” / “Compatibility Mode : Off” is displayed on
screen.)

- Change the setting for “Compatibility Mode” on the
“Administrator Settings” menu (see “Compatibility

Mode” (page 27)).

33

Chapter 6 Reference

Chapter 6 Reference

6-1. Attaching the Optional Arm

An optional arm (or an optional stand) can be attached by removing the stand section. Please refer to our
web site for the supported optional arm (or optional stand). http://www.eizoglobal.com

Attention

• When attaching an arm or stand, follow the instructions of the respective User’s Manual.

• When using another manufacturer’s arm or stand, conrm the following in advance and select one conforming to

the VESA standard. Use the VESA mounting screws supplied with this product when attaching the arm or stand.

- Clearance between screw holes: 100 mm × 100 mm

- VESA mount of the arm or stand, external dimensions: 122 mm x 122 mm or less

- Plate thickness: 2.6 mm

- Strong enough to support weight of the monitor unit (excluding the stand) and attachments such as cables.

• When attaching an arm or stand, the installable orientations and movement range (tilt angle) are as follows:

Orientation

*1

Movement
range
(tilt angle)

Up: 45˚ Down: 45˚

*1 When installed in this orientation, periodically clean the area around the power connector. Dust, water, or

oil adhered to this area may result in re.

• Connect the cables after attaching an arm or stand.

• Do not move the removed stand up and down. Doing so may result in injury or device damage.

• The monitor, arm, and stand are heavy. Dropping them may result in injury or equipment damage.

34

Chapter 6 Reference

●

Attaching the Optional Arm (or Optional Stand)

1. Lay the LCD monitor on a soft cloth spread over a stable and at surface with the panel surface
facing down.

2. Remove the stand.

As shown below, keep the lock button pressed down (1) and slide the stand towards the stand base until it
touches (2). Then, lift the stand up (3).

(3)

(2)

(1)(1)

3. Attach the arm or stand to the monitor.

Use the VESA mounting screws supplied with this product when attaching the arm or stand.

●

Attaching the original stand

1. Remove the xing screws on the optional arm (or optional stand), and detach the optional arm (or
optional stand).

2. To prevent damaging the panel surface, lay the monitor with its panel surface facing down on a
soft cloth spread on a stable surface.

3. Attach the original stand.

As shown below, insert the four tabs on the stand into the square holes on the back panel (1) and slide the
stand towards the upper portion of the monitor until it makes a clicking sound (2).

Click

!

(1)

(2)

(2)

35

Chapter 6 Reference

6-2. Detaching / Attaching Stand Base

●

Detachment procedure

The stand base that was attached during setup can be detached using the following procedures.

1. Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing
down.

2. Raise the lever on the bottom of the stand base.

3. Turn the stand base in the counterclockwise direction to detach it.

36

Chapter 6 Reference

●

Attachment procedure

The once removed the stand base can be attached to the monitor again with the following procedures.

1. Lay the LCD monitor on a soft cloth spread over on a stable surface with the panel surface facing
down.

2. Attach the stand base onto the stand brace.

3. Turn the stand base clockwise until it makes a clicking sound.

Click

!

37

Chapter 6 Reference

6-3. Attaching / Detaching the Cable Holder

A cable holder is supplied with this product. Use the cable holder to organize the cables connected to the
monitor.

●

Attachment procedure

1. Pass the cables through the cable holder.

2. Close the cable holder.

3. While holding the cable holder closed, insert it into the stand.

Note

• The cable holder can be inserted either perpendicular or parallel to the stand. Change the orientation of the
cable holder in line with the direction of the cables.

38

Chapter 6 Reference

●

Detachment procedure

1. Close the cable holder.

2. While holding the cable holder closed, pull it from the stand.

6-4. Connecting Multiple PCs

This product can be connected to multiple PCs and allows you to switch between the connections for
display.

●

Connection examples

DisplayPort

HH200HS (HDMI - HDMI) HDMIHDMI

PP200 (DisplayPort - DisplayPort) DisplayPort

USB-C CC200SS (USB-C - USB-C) USB-C

(supplied)

(optional)

(optional)

Note

• You can select the input signal to display using the operation switch on the front of the monitor. For details,
see “2-2. Switching Input Signals” (page 14).

• This product provides a function that automatically recognizes the connector through which PC signals are input,

and displays images on the screen accordingly. For details, see “Auto Input Detection” (page 27).

39

Chapter 6 Reference

6-5. Using the USB Hub Function

This monitor is equipped with a USB hub. It functions as a USB hub when connected to a USB­compatible PC, allowing the connection of peripheral USB devices.

●

Connection Procedure

1. Connect the USB cable between the USB-C connectors of the PC and the monitor.

2. Connect a peripheral USB device to the USB downstream port of the monitor.

Attention

• If your PC is not equipped with a USB-C connector, a USB-C to Type-A conversion cable is required. Connect
the conversion cable between the USB downstream port of the PC and the USB-C connector of the monitor.

• When you change the setting of “USB Power Delivery” (page 24) or “Compatibility Mode” (page 27),
remove any peripherals such as a USB memory device connected to the downstream port of the monitor.

• When the main power of the monitor is off, a device connected to the USB downstream port will not operate.

• When “Compatibility Mode” (page 27) is set to “Off” and the power to the monitor is turned off, a device

connected to the USB downstream port will not work.

Note

• This product supports USB 3.1*1. When connecting to peripheral devices that support USB 3.1, high-speed data
communication is possible (however, only when the USB cable used to connect the PC and peripheral device is
USB 3.1 compliant).

*1 Only Gen1 5 Gbps is supported.

40

Chapter 6 Reference

6-6. Specications

LCD Panel Type IPS (Anti-Glare)

Backlight LED
Size 68.5 cm (27.0 inch)
Native Resolution 2560 dots × 1440 lines
Display Size (H × V) 596.7 mm × 335.7 mm
Pixel Pitch 0.233 mm
Display Colors 8-bit colors : 16.77 million colors

Viewing Angle (H / V, typical) 178˚ / 178˚
Response Time (typical) Gray-to-gray : 15 ms (overdrive setting: Off)

5 ms (overdrive setting: Enhanced)

Video Signals Input Terminals DisplayPort (HDCP) × 1, HDMI (HDCP)

*1

× 1, USB-C×1

Digital Scanning Frequency
(H / V)

DisplayPort : 31 kHz to 89 kHz / 59 Hz to 61 Hz
HDMI : 31 kHz to 89 kHz / 29 Hz to 31 Hz,

49 Hz to 51 Hz, 59 Hz to 61 Hz

USB-C (DP Alt Mode

) : 31 kHz to 89 kHz / 29 Hz to 31 Hz,

59 Hz to 61 Hz
Synchronization Signal Separate
Max. Dot Clock 241.5 MHz

USB Port Upstream port (USB-C) × 1, Downstream port (USB Type-A) × 2

Standard USB Specication Revision 3.1

*2

Communication Speed 5 Gbps (super), 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Downstream supplied power USB Type-A: Max. 900 mA per port
Upstream supplied power USB-C: Max. 15 W / Max. 30 W

Audio Audio Input Format DisplayPort: 2ch linear PCM (32 kHz / 44.1 kHz / 48

kHz / 88.2 kHz / 96 kHz)

USB-C (DP Alt Mode): 2ch linear PCM (32 kHz / 44.1 kHz / 48

kHz / 88.2 kHz / 96 kHz)

HDMI: 2ch linear PCM (32 kHz / 44.1 kHz / 48

kHz)
Speakers 1 W + 1 W
Headphones 2 mW + 2 mW (32 Ω)
Input Terminals DisplayPort × 1, HDMI × 1, USB-C × 1 (shared with video signal)
Output Terminals Headphones: Stereo mini jack × 1

Power Input 100 - 240 VAC ±10 %, 50 / 60 Hz 1.0 A - 0.45 A

Maximum Power Consumption 96 W or less
Power Save Mode 0.5 W or less (no USB device connected, default settings)
Standby Mode 0.5 W or less (no USB device connected, default settings)

Physical
Specications

Dimensions 611.6 mm × 399 mm to 544 mm × 259 mm (W × H × D)

(Tilt: 35˚)

611.6 mm × 390.2 mm to 545.2 mm × 245 mm (W × H × D)
(Tilt: 0˚)

Dimensions (Without Stand) 611.6 mm × 359 mm × 48.5 mm (W × H × D)
Net Weight Approx. 8.1 kg

Net Weight (Without Stand) Approx. 5.3 kg
Height Adjustment Range 145 mm (Tilt: 35˚) / 155 mm (Tilt: 0˚)
Tilt Up 35˚, down 5˚
Swivel 344˚
Vertical Rotation Left 90˚, right 90˚

41

Chapter 6 Reference

Operating
Environmental
Requirements

Temperature 5 ˚C to 35 ˚C (41 ˚F to 95 ˚F)
Humidity 20 % to 80 % R.H. (no condensation)
Air Pressure 540 hPa to 1060 hPa

Transportation/
Storage
Environmental
Requirements

Temperature -20 ˚C to 60 ˚C (-4 ˚F to 140 ˚F)
Humidity 10 % to 90 % R.H. (no condensation)
Air Pressure 200 hPa to 1060 hPa

*1 HDMI CEC (or mutual control) is not supported.
*2 Only Gen1 5 Gbps is supported.

●

Main Default Settings

Auto EcoView On
EcoView Optimizer 2 On
Color Mode User 1
Picture Expansion USB-C input Aspect Ratio

DisplayPort input Aspect Ratio
HDMI (PC signal) input Aspect Ratio
HDMI (video signal) input Auto

Input Color Format USB-C input Auto

DisplayPort input Auto
HDMI (PC signal) input RGB
HDMI (video signal) input Auto

Power Save On
Power Indicator On
USB Power Delivery 15 W
Language English
Auto Input Detection Off
Compatibility Mode Off
USB-C Display Mode Normal
Auto PbyP Resolution On
On-Screen Logo On
Key Lock Off

●

Accessories

Signal cable • HH200HS (HDMI-HDMI)

• PP200 (DisplayPort-DisplayPort)

Cleaning Kit EIZO “ScreenCleaner”
For the latest information about accessories, refer to our web site. http://www.eizoglobal.com

42

Chapter 7 Glossary

Chapter 7 Glossary

DisplayPortoverUSBType-C（DPAltMode（

One of the extended specications (Alternate Mode) of USB Type-C (USB-C) dened by VESA,
where a single USB cable is capable of transmitting DisplayPort signals and performing USB
communication.

HDCP (High-bandwidth Digital Content Protection)

Digital signal coding system developed to copy-protect the digital contents, such as video, music,
etc.
This helps to transmit the digital contents safely by coding the digital contents sent via the DVI or
HDMI connector on the output side and decoding them on the input side.
Any digital contents cannot be reproduced if both of the equipments on the output and input sides
are not applicable to HDCP system.

Overdrive

This technology enhances response speed by increasing the potential difference at the time of
motion of liquid-crystal pixels, and it is used for liquid-crystal TV sets and others in general. It
provides clear-cut three-dimensional display with little afterimage, by improving response speed of
the intermediate graduation range that frequently appears in moving images.

USB Power Delivery

An optional USB standard, where a single USB cable is capable of supplying power of up to 100 W
(20 V / 5 A).

43

Appendix

Appendix

Trademark

The terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing, LLC in the United States and other countries.

The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics
Standards Association.

The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers
Forum, Inc.

Kensington and Microsaver are registered trademarks of ACCO Brands Corporation.
Thunderbolt is a trademark of Intel Corporation in the United States and/or other countries.
Microsoft, Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United

States and other countries.
Adobe is a registered trademark of Adobe Systems Incorporated in the United States and other

countries.
Apple, Mac OS, OS X, Macintosh, and ColorSync are registered trademarks of Apple Inc.
EIZO, the EIZO Logo, ColorEdge, DuraVision, FlexScan, FORIS, RadiCS, RadiForce, RadiNET, Raptor

and ScreenManager are registered trademarks of EIZO Corporation in Japan and other countries.
ColorEdge Tablet Controller, ColorNavigator, CuratOR, EcoView NET, EIZO EasyPIX, EIZO Monitor

Congrator, EIZO ScreenSlicer, G-Ignition, i-Sound, Quick Color Match, RadiLight, Re/Vue, Screen
Administrator, Screen InStyle, and UniColor Pro are trademarks of EIZO Corporation.

All other company and product names are trademarks or registered trademarks of their respective
owners.

License

A round gothic bold bit map font designed by Ricoh is used for the characters displayed on this product.

ENERGY STAR

As an ENERGY STAR Partner, EIZO Corporation has determined that this product meets
the ENERGY STAR guidelines for energy efciency.

TCO

This product has acquired the TCO standard that relates to the safety, ergonomics, environment and so
forth of ofce equipment.
For details, see the following pages.

44

Appendix

Congratulations!

ThisproductisTCOCertied–forSustainableIT

TCO Certi ed is an international third party sustainability certi cation for IT
products. TCO Certi ed ensures that the manufacture, use and recycling of IT
products re ect environmental, social and economic responsibility. Every TCO
Certi ed product model is veri ed by an accredited independent test laboratory.

This product has been veri ed to meet all the criteria in TCO Certi ed, including:

Corporate Social Responsibility

Socially responsible production – working conditions and labor law in manufacturing country

EnergyEfciency

Energy ef ciency of product and power supply. Energy Star compliant, where applicable

Environmental Management System

Manufacturer must be certi ed according to either ISO 14001 or EMAS

Minimization of Hazardous Substances

Limits on cadmium, mercury, lead & hexavalent chromium including requirements for mercury-free
products, halogenated substances and hazardous  ame retardants

Design for Recycling

Coding of plastics for easy recycling. Limit on the number of different plastics used.

Product Lifetime, Product Take Back

Minimum one-year product warranty. Minimum three-year availability of spare parts. Product takeback

Packaging

Limits on hazardous substances in product packaging. Packaging prepared for recycling

Ergonomic, User-centered design

Visual ergonomics in products with a display. Adjustability for user comfort (displays, headsets)
Acoustic performance – protection against sound spikes (headsets) and fan noise (projectors, computers)
Ergonomically designed keyboard (notebooks)

Electrical Safety, minimal electro-magnetic Emissions
Third Party Testing

All certi ed product models have been tested in an independent, accredited laboratory.

A detailed criteria set is available for download at www.tcodevelopment.com, where you can also  nd a
searchable database of all TCO Certi ed IT products.

TCO Development, the organization behind TCO Certi ed, has been an international driver in the  eld
of Sustainable IT for 20 years. Criteria in TCO Certi ed are developed in collaboration with scientists,
experts, users and manufacturers. Organizations around the world rely on TCO Certi ed as a tool to
help them reach their sustainable IT goals. We are owned by TCO, a non-pro t organization representing
of ce workers. TCO Development is headquartered in Stockholm, Sweden, with regional presence in
North America and Asia

For more information, please visit

www.tcodevelopment.com

45

Appendix

FCC Declaration of Conformity

For U.S.A. ,Canada Only

FCC Declaration of Conformity

We, the Responsible Party EIZO Inc.

5710 Warland Drive, Cypress, CA 90630
Phone: [phone]

declare that the product Trade name: EIZO

Model: FlexScan EV2780

is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation.

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures.

* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
* Consult the dealer or an experienced radio/TV technician for help.

Changesormodicationsnotexpresslyapprovedbythepartyresponsibleforcompliancecould

void the user’s authority to operate the equipment.

Note

UsetheattachedspeciedcablebeloworEIZOsignalcablewiththismonitorsoastokeep

interference within the limits of a Class B digital device.

- AC Cord

- Shielded Signal Cable (enclosed)

Canadian Notice

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.

46

Appendix

LIMITED WARRANTY

EIZO Corporation (hereinafter referred to as “EIZO”) and distributors authorized by EIZO (hereinafter referred to as the

“

Distributors

”) warrant, subject to and in accordance with the terms of this limited warranty (hereinafter referred to as the

“

Warranty”), to the original purchaser (hereinafter referred to as the “Original Purchaser

”) who purchased the product

speci ed in this document (hereinafter referred to as the “

Product

”) from EIZO or Distributors, that EIZO and Distributors
shall, at their sole discretion, either repair or replace the Product at no charge if the Original Purchaser becomes aware
within the Warranty Period (de ned below) that the Product malfunctions or is damaged in the course of normal use of
the Product in accordance with the description in the instruction manual attached to the Product (hereinafter referred to

as the “

User’s Manual”).

The period of this Warranty is limited to (i) five (5) years from the date of purchase of the Product; or, limited to the
expiration of (ii) 30,000 hours of its use of the Product (hereinafter referred to as the “

Warranty Period

”). EIZO and
Distributors shall bear no liability or obligation with regard to the Product in relation to the Original Purchaser or any third
parties other than as provided under this Warranty.

EIZO and Distributors will cease to hold or store any parts (excluding design parts) of the Product upon expiration of  ve (5)
years after the production of the product is discontinued. In repairing the monitor, EIZO and Distributors will use renewal
parts which comply with our QC standards. If the unit cannot be repaired due to its condition or the stockout of



a relevant

part, EIZO and Distributors may offer the replacement by a product with equivalent performance instead of repairing it.
The Warranty is valid only in the countries or territories where the Distributors are located. The Warranty does not restrict

any legal rights of the Original Purchaser.
Notwithstanding any other provision of this Warranty, EIZO and Distributors shall have no obligation under this Warranty

whatsoever in any of the cases as set forth below:

(a) Any defect of the Product caused by freight damage, modi cation, alteration, abuse, misuse, accident, incorrect

installation, disaster, faulty maintenance and/or improper repair by third party other than EIZO and Distributors;
(b) Any incompatibility of the Product due to possible technical innovations and/or regulations;
(c) Any deterioration of the sensor;
(d) Any deterioration of display performance caused by the deterioration of expendable parts such as the LCD panel

and/or backlight, etc. (e.g. changes in brightness, changes in brightness uniformity, changes in color, changes in

color uniformity, defects in pixels including burnt pixels, etc.);
(e) Any defect of the Product caused by external equipment;
(f) Any defect of the Product on which the original serial number has been altered or removed;

(g) Any normal deterioration of the product, particularly that of consumables, accessories, and/or attachments (e.g.

buttons, rotating parts, cables, User’s Manual, etc.); and
(h) Any deformation, discoloration, and/or warp of the exterior of the product including that of the surface of the LCD

panel.

To obtain service under the Warranty, the Original Purchaser must deliver the Product, freight prepaid, in its original
package or other adequate package affording an equal degree of protection, assuming the risk of damage and/or loss
in transit, to the local Distributor. The Original Purchaser must present proof of purchase of the Product and the date of
such purchase when requesting services under the Warranty.

The Warranty Period for any replaced and/or repaired product under this Warranty shall expire at the end of the original
Warranty Period.

EIZO OR DISTRIBUTORS ARE NOT RESPONSIBLE FOR ANY DAMAGE TO, OR LOSS OF, DATA OR OTHER
INFORMATION STORED IN ANY MEDIA OR ANY PART OF ANY PRODUCT RETURNED TO EIZO OR DISTRIBUTORS
FOR REPAIR.

EIZO AND DISTRIBUTORS MAKE NO FURTHER WARRANTIES, EXPRESSED OR IMPLIED, WITH RESPECT TO
THE PRODUCT AND ITS QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR
USE. IN NO EVENT SHALL EIZO OR DISTRIBUTORS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL,
CONSEQUENTIAL OR OTHER DAMAGE WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR
LOSS OF PROFIT, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY
LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT OR IN ANY CONNECTION WITH THE
PRODUCT, WHETHER BASED ON CONTRACT, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, EVEN
IF EIZO OR DISTRIBUTORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THIS EXCLUSION
ALSO INCLUDES ANY LIABILITY WHICH MAY ARISE OUT OF THIRD PARTY CLAIMS AGAINST THE ORIGINAL
PURCHASER. THE ESSENCE OF THIS PROVISION IS TO LIMIT THE POTENTIAL LIABILITY OF EIZO AND
DISTRIBUTORS ARISING OUT OF THIS LIMITED WARRANTY AND/OR SALES.

47

Appendix

Recycling Information

Recycling Information

This product, when disposed of, is supposed to be collected and recycled according to your country’s
legislation to reduce environmental burden. When you dispose of this product, please contact a distributor or
an af liate in your country.
The contact addressees are listed on the EIZO website below.
http://www.eizoglobal.com

For recycling information for customers in Switzerland, please refer to the following website.
http://www.swico.ch

For customers in the United States, a free take-back program for the product and packaging materials is
available. Please refer to the following website for details.
http://www.eizo.com/warranty/recycling/

Informationen zum Thema Recycling

Dieses Produkt muss gemäß den Vorschriften Ihres Landes zur Entlastung der Umwelt recyclet werden.
Wenden Sie sich bei der Entsorgung dieses Produkts an einen Verteiler oder eine Tochtergesellschaft in
Ihrem Land.
Die Adressen zur Kontaktaufnahme sind auf der unten angegebenen Website von EIZO aufgeführt.
http://www.eizoglobal.com

Kunden in der Schweiz entnehmen Informationen zum Recycling der folgenden Website:
http://www.swico.ch

Informations sur le recyclage

Ce produit doit être jeté aux points de collecte prévus à cet effet et recyclé conformément à la législation de
votre pays, a n de réduire l’impact sur l’environnement. Lorsque vous jetez ce produit, veuillez contacter un
distributeur ou une société af liée de votre pays.
Les adresses des distributeurs sont répertoriées sur le site Web EIZO ci-dessous.
http://www.eizoglobal.com

Pour les clients en Suisse, veuillez consulter le site Web suivant afin d’obtenir des informations sur le
recyclage.
http://www.swico.ch

Información sobre reciclaje

Este producto debe desecharse y reciclarse según la legislación del país para reducir el impacto
medioambiental. Cuando desee deshacerse de este producto, póngase en contacto con un distribuidor o
una  lial de su país.
Encontrará las direcciones de contacto en el sitio web de EIZO que se indica a continuación.
http://www.eizoglobal.com

Informazioni sul riciclaggio

Per lo smaltimento e il riciclaggio del presente prodotto, attenersi alle normative vigenti nel proprio paese per
ridurre l’impatto ambientale. Per lo smaltimento, rivolgersi ad un distributore o un af liato presenti nel proprio
paese.
Gli indirizzi sono elencati nel sito Web EIZO riportato di seguito.
http://www.eizoglobal.com

Per informazioni sul riciclaggio per i clienti in Svizzera, consultare il sito Web riportato di seguito.
http://www.swico.ch

48

Appendix

Återvinningsinformation

När denna produkt kasseras ska den hanteras och återvinnas enligt landets föreskrifter för att reducera
miljöpåverkan. När du kasserar produkten ska du kontakta en distributör eller representant i ditt land.
Kontaktadresserna listas på EIZO-webbplatsen nedan.
http://www.eizoglobal.com

Πληροφορίεςανακύκλωσης

Το προϊόν αυτό, όταν απορρίπτεται, πρέπει να συλλέγεται και να ανακυκλώνεται σύμφωνα με τη νομοθεσία
της χώρας σας έτσι ώστε να μην επιβαρύνει το περιβάλλον. Για να απορρίψετε το προϊόν, επικοινωνήστε με
έναν αντιπρόσωπο ή μια θυγατρική εταιρεία στη χώρα σας.
Οι διευθύνσεις επικοινωνίας αναγράφονται στην τοποθεσία web της EIZO παρακάτω.
http://www.eizoglobal.com

Сведенияпоутилизации

По истечении срока службы данного продукта его следует принести на сборный пункт и
утилизировать в соответствии с действующими предписаниями в вашей стране, чтобы уменьшить
вредное воздействие на окружающую среду. Прежде чем выбросить данный продукт, обратитесь к
дистрибьютору или в местное представительство компании в вашей стране.
Контактные адреса можно найти на веб-узле EIZO.
http://www.eizoglobal.com

Informatie over recycling

Wanneer u dit product wilt weggooien, moet het uit milieu-overwegingen worden verzameld en gerecycled
volgens de betreffende wetgeving van uw land. Wanneer u dit product wilt weggooien, moet u contact
opnemen met een distributeur of een partner in uw land.
De contactadressen worden vermeld op de volgende EIZO-website.
http://www.eizoglobal.com

Informação sobre reciclagem

Este produto, quando o deitar fora, deve ser recolhido e reciclado de acordo com a legislação do seu país
para reduzir a poluição. Quando deitar fora este produto, contacte um distribuidor ou uma  lial no seu país.
Os endereços de contacto estão listados no website do EIZO, abaixo.
http://www.eizoglobal.com

Oplysninger om genbrug

Dette produkt forventes ved bortskaffelse at blive indsamlet og genbrugt i overensstemmelse med
lovgivningen i dit land for at reducere belastningen af miljøet. Når du bortskaffer denne produkt, skal du
kontakte en distributør eller et tilknyttet selskab i dit land.
Adresserne på kontaktpersonerne er angivet på EIZO’s websted nedenfor.
http://www.eizoglobal.com

Kierrätystä koskevia tietoja

Tuote tulee hävittää kierrättämällä maan lainsäädännön mukaisesti ympäristön kuormittumisen
vähentämiseksi. Kun hävität tuotteen, ota yhteyttä jälleenmyyjään tai tytäryhtiöön maassasi.
Yhteystiedot löytyvät EIZOn Internet-sivustolta.
http://www.eizoglobal.com

49

Appendix

Wykorzystanie surowców wtórnych

Ten produkt po zużyciu powinien być zbierany i przetwarzany zgodnie z krajowymi przepisami dotyczącymi
ochrony środowiska. Wyrzucając ten produkt, należy skontaktować się z lokalnym dystrybutorem lub
partnerem. Adresy kontaktowe można znaleźć we wskazanej poniżej witrynie internetowej  rmy EIZO.
http://www.eizoglobal.com

Informace o recyklaci

Při likvidaci produktu musí být produkt vyzvednut a recyklován podle zákonů příslušné země, aby
nedocházelo k zatěžování životního prostředí. Zbavujete-li se produktu, kontaktujte distributora nebo
pobočku ve své zemi.

Kontaktní adresy jsou uvedeny na následující webové stránce společnosti EIZO.

http://www.eizoglobal.com

Ringlussevõtu alane teave

Keskkonnakoormuse vähendamiseks tuleks kasutatud tooted kokku koguda ja võtta ringlusse vastavalt teie
riigi seadustele. Kui kõrvaldate käesoleva toote, võtke palun ühendust turustaja või  liaaliga oma riigis.
Kontaktisikud on toodud EIZO veebilehel järgmisel aadressil:
http://www.eizoglobal.com

Újrahasznosítási információ

Jelen terméket, amikor eldobjuk, az illető ország törvényei alapján kell összegyűjteni és újrahasznosítani,
hogy csökkentsük a környezet terhelését. Amikor ezt a terméket eldobja, kérjük lépjen kapcsolatba egy
országon belüli forgalmazóval vagy társvállalkozással.
A kapcsolat címei az EIZO alábbi weboldalán találhatók felsorolva:
http://www.eizoglobal.com

Podatki o recikliranju

Ob koncu uporabe odslužen izdelek izročite na zbirno mesto za recikliranje v skladu z okoljevarstveno
zakonodajo vaše države. Prosimo, da se pri odstranjevanju izdelka obrnete na lokalnega distributerja ali
podružnico.
Kontaktni naslovi so objavljeni na spodaj navedenih spletnih straneh EIZO:
http://www.eizoglobal.com

Informácie o recyklácii

Pri likvidácii musí byť tento výrobok recyklovaný v súlade s legislatívou vašej krajiny, aby sa znížilo zaťaženie
životného prostredia. Keď sa chcete zbaviť tohto výrobku, kontaktujte prosím distribútora alebo pobočku vo
vašej krajine.
Zoznam kontaktných adries je uvedený na nasledovnej webovej stránke  rmy EIZO:
http://www.eizoglobal.com

Pārstrādesinformācija

Utilizējot šo produktu, tā savākšana un pārstrāde veicama atbilstoši jūsu valsts likumdošanas prasībām
attiecībā uz slodzes uz vidi samazināšanu. Lai veiktu šī produkta utilizāciju, sazinieties ar izplatītāju vai
pārstāvniecību jūsu valstī.
Kontaktadreses ir norādītas zemāk minētajā EIZO tīmekļa vietnē.
http://www.eizoglobal.com

50

Appendix

Informacijaapiegrąžinamąjįperdirbimą

Šalinant (išmetant) šiuos gaminius juos reikia surinkti ir perdirbti grąžinamuoju būdu pagal jūsų šalies teisės
aktus, siekiant sumažinti aplinkos teršimą. Kai reikia išmesti šį gaminį, kreipkitės į jūsų šalyje veikiančią
gaminių pardavimo atstovybę arba jos  lialą.
Kontaktiniai adresatai nurodyti EIZO interneto svetainėje.
http://www.eizoglobal.com

Информацияотноснорециклиране

При изхвърлянето на този продукт се предлага събирането и рециклирането му съобразно законите на
вашата страна за да се намали замърсяването на околната среда. Когато искате да се освободите от
този продукт, моля свържете се с търговския му представител или със съответните органи отговарящи
за това във вашата страна.
Данните за връзка с нас са описани на следния Интернет сайт на EIZO:
http://www.eizoglobal.com

Informaţiereferitoarelareciclare

Acest produs, când debarasat, trebuie colectat şi reciclat conform legislaţiei ţării rspective ca să reducem
sarcina mediului. Când se debarasează de acest produs, vă rugăm să contactaţi un distribuitor sau un a liat
al ţării respective.
Adresele de contact le găsiţi pe pagina de web al EIZO:
http://www.eizoglobal.com

GeriDönüşümBilgisi

Bu ürünün, atılacağı zaman, ülkenizin çevre kirliliğinin azaltılması konusundaki mevzuatına göre toplanması
ve yeniden değerlendirilmesi gerekmektedir. Ürünü atacağınız zaman lütfen ülkenizdeki bir distribütör veya
ilgili kuruluşla temasa geçiniz.
İrtibat adresleri aşağıdaki EIZO web sitesinde verilmiştir.
http://www.eizoglobal.com

(UM-EV2780)

03V26241A1

1st Edition-October, 2016

Copyright © 2016 EIZO Corporation. All rights reserved.