Page 1
Important
Please read this User’s Manual carefully to familiarize yourself with safe and
effective usage.
Please retain this manual for future reference.
重要
请仔细阅读用户手册，熟练掌握其安全和有效的操作程序。
请妥善保存此手册，供日后参考。
Page 2
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product Trade name: EIZO
Model: DuraVision FDX1001/FDV1001
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
Page 3
Page 4
2
Copyright© 2009-2010 EIZO NANAO CORPORATION All rights reserved.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or information condential
unless prior arrangements are made pursuant to EIZO NANAO CORPORATION’s receipt of said information.
Although every effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.
Apple and Macintosh are registered trademarks of Apple Inc.
VGA is a registered trademark of International Business Machines Corporation.
Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States and other countries.
VESA is a registered trademark or a trademark of Video Electronics Standards Association in the United States and other countries.
PC-9801 and PC-9821 are trademarks of NEC Corporation.
EIZO and EIZO Logo are registered trademarks of EIZO NANAO CORPORATION in Japan and other countries.
DuraVision is a trademark of EIZO NANAO CORPORATION.
All other trademarks are the properties of their respective owners.
SAFETY SYMBOLS
This manual and this product use the safety symbols below. They denote critical information. Please read them carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious injury and can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate injury and/or property or product damage.
Indicates an attention to be required. For example, the symbol
illustrates the hazard type such as “the
risk of electric shock”.
Indicates a prohibited action. For example, the symbol
illustrates a particular prohibited action
such as “Do not disassemble”.
Indicates a mandatory action that must be followed. For example, the symbol illustrates the
notication of general prohibition such as “Grounding the unit”.
Using the special functions, such as screen size change (ex. changing the horizontal and vertical ratio of images input)
for commercial purposes or for the purpose of showing in public may violate copyright laws.
Product specication may vary with sales areas.
Conrm the specication in the manual written in language of the region of purchase.
Page 5
3
PRECAUTIONS
IMPORTANT
• To ensure personal safety and proper maintenance, please read this section and the caution statements
on the unit (refer to the gure below).
【
Location of Caution Statement
】
WARNING
If the unit begins to emit smoke, smells like something is burning, or makes strange
noises, disconnect all power connections immediately and contact your dealer for
advice.
Attempting to use a malfunctioning unit may result in re, electric shock, or equipment damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in re, electric shock, or burn.
Refer all servicing to qualied service personnel.
Do not attempt to service this product yourself as opening or removing covers may result in re,
electric shock, or equipment damage.
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet or spillage into
the cabinet may result in re, electric shock, or equipment damage. If an object or liquid falls/
spills into the cabinet, unplug the unit immediately. Have the unit checked by a qualied service
engineer before using it again
.
Place the unit at the strong and stable place.
A unit placed on an inadequate surface may fall and result in injury or equipment damage. If
the unit falls, disconnect the power immediately and ask your dealer for advice. Do not continue
using a damaged unit. Using a damaged unit may result in re or electric shock.
Page 6
4
WARNING
Use the unit in an appropriate location.
Not doing so may result in re, electric shock, or equipment damage.
Do not place outdoors.
Do not place in a transportation system (ship, aircraft, train, automobile, etc.) where it may be
affected by strong vibration or shock.
Do not place in a dusty or humid environment.
Do not place in a location where water is splashed on the screen (bathroom, kitchen, etc.).
Do not place in a location where the steam comes directly on the screen.
Do not place near heat generating devices or a humidier
Do not place in an inammable gas environment.
•
•
•
•
•
•
•
To avoid danger of suffocation, keep the plastic packing bags away from babies and
children.
Use the enclose AC adapter.
The enclosed AC adapter is for use with this product only. Do not use the AC adapter with other
equipment. Connecting to power sources that do not match the power ratings of the AC adapter
may result in re or electric shock.
Make sure the power cord meets the following requirements.
This product does not include a power cord. Please provide separately a power cord which
meets the requirements. (For more information, please contact your dealer.)
The power cord is compatible with the standards of the country and region in which
this product is to be used.
The power cord has a rated value of at least 2.5A.
Power supply: 100-240Vac 50/60Hz
•
•
To disconnect the power cord, grasp the plug rmly and pull.
Tugging on the cord may damage and result in re or electric shock.
Use the correct voltage.
The unit is designed for use with a specic voltage only. Connection to another voltage than
specied in this User’s Manual may cause re, electric shock, or equipment damage.
Power supply: 100-240Vac 50/60Hz
• Do not overload your power circuit, as this may result in re or electric shock.
•
Handle the power cord and AC adapter with care.
Do not place heavy objects on, pull or tie the power cord or the AC adapter. Use of a damaged
cord or AC adapter may result in re or electric shock.
Never touch the plug, AC adapter or power cord during a thunderstorm.
Touching them may result in electric shock.
When attaching an arm stand, please refer to the user’s manual of the arm stand and
install the unit securely.
Not doing so may cause the unit to become unattached, which may result in injury or equipment
damage. When the unit is dropped, please ask your dealer for advice. Do not continue using a
damaged unit. Using a damaged unit may result in re or electric shock. When reattaching the
tilt stand, please use the same screws and tighten them securely.
Page 7
5
WARNING
Do not touch a damaged LCD panel directly with bare hands.
The liquid crystal that may leak from the panel is poisonous if it enters the eyes or mouth. If any
part of the skin or body comes in direct contact with the panel, please wash thoroughly. If some
physical symptoms result, please consult your doctor.
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit with the cord
attached is dangerous. It may result in injury.
When handling the unit, grip the bottom of the unit rmly withboth hands
ensuring the panel faces outward before lifting.
Dropping the unit may result in injury or equipment damage.
Do not install the unit in a closed space.
If the inerior becomes hot, it may result in re, electric shock or damage.
Do not touch the power plug or AC adapter with wet hands.
Doing so may result in electrical shock.
Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a problem.
Mind that the AC adapter becomes hot during use.
Do not cover or place anything on top of the AC adapter. Do not place the AC adapter on
top of things that trap heat such as carpets, blankets, etc. Keep the AC adapter away from
direct sunlight and heat sources such as heaters.
Not doing so may result in re.
Do not touch with bare hands. Doing so may result in burns.
•
•
Do not suspend the AC adapter in midair.
Using it while suspended in midair may result in re or electric shock.
Periodically clean the area around the plug.
Dust, water, or oil on the plug may result in re.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric shock.
If you plan to leave the unit unused for an extended period, disconnect the power cord
from the wall socket after turning off the power for safety and power conservation.
Page 8
6
Notice for this monitor
Aside from displaying microscope images, this product is also suited to the dedicated usages such as operation of
terminal equipment.
This product has been adjusted specically for use in the region to which it was originally shipped. If the product is used
outside the region, it may not operate as specied in the specications.
This product may not be covered by warranty for uses other than those described in this manual.
The specications specied in this manual are only applicable to signal cables specied by US.
Use optional products manufactured or specied by us with this product.
As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more
after the monitor power has been turned on.
In order to suppress the luminosity change by long-term use and to maintain the stable luminosity, use of a monitor in
lower brightness is recommended.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Set up the screen saver and/or make use of the power saving function to avoid displaying the same image for
extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime.
(Refer to “Cleaning” on the next page.)
The LCD panel is manufactured using high-precision technology. However, missing pixels or lit pixels may appear on
the LCD panel, this is not malfunction. Percentage of effective pixels : 99.99% or higher.
The backlight of the LCD panel has a xed life span. When the screen becomes dark or begins to icker, please contact
your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in the display malfunction, such as the
interference patterns, etc. If pressure is continually applied to the LCD panel, it may deteriorate or damage your LCD
panel. (If the pressure marks remain on the LCD panel, leave the monitor with a white or black screen. The symptom
may disappear.)
Do not scratch or press on the panel with any sharp objects, such as a pencil or pen as this may result in damage to the
panel. Do not attempt to brush with tissues as this may scratch the LCD panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation
may occur inside and outside the monitor. In that case, do not turn the monitor on and wait until dew condensation
disappears, otherwise it may cause some damages to the monitor.
Page 9
7
Cleaning
ATTENTION
Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, and abrasive cleaner, which may
damage the cabinet or LCD panel.
•
NOTE
Optional ScreenCleaner is recommended for cleaning the panel surface.•
● LCD Panel
Clean the LCD panel with a soft cloth such as cotton cloth or lens cleaning paper.
Remove persistent stains gently with a cloth dampened with a little water, and then clean the LCD panel
again with a dry cloth for better nishing.
● Cabinet
Clean the cabinet with a soft cloth dampened with a little mild detergent.
To use the monitor comfortably
An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor
according to the environmental conditions.
Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
•
•
•
•
•
Page 10
8
CONTENTS
CONTENTS
Cover .............................................................1
PRECAUTIONS ................................................3
Notice for this monitor .............................................. 6
CONTENTS .............................................................8
Chapter 1 Introduction ........................................
9
1-1. Features .............................................................. 9
1-2. Package Contents .............................................. 9
1-3. Controls and Functions ................................... 10
Chapter 2 Connecting Cables .......................... 11
2-1. Connection Procedures ....................................11
● When used as a PC monitor .............................11
● When using video equipment ........................... 12
2-2. Adjusting the Screen Angle ............................. 13
Chapter 3 Settings and Adjustments ..............14
3-1. Basic Operation and Functions ...................... 14
3-2. Color Adjustment ............................................. 16
3-3. Congure other settings .................................. 17
Chapter 4 Troubleshooting ...............................18
Chapter 5 Reference .........................................
19
5-1. Attaching an Arm .............................................. 19
5-2. Specications ................................................... 20
5-3. Glossary ............................................................ 24
5-4. Preset Timing ....................................................25
LIMITED WARRANTY ..........................................26
Page 11
9
Chapter 1 Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
10.4-inch screen
Resolution
FDX1001: XGA (1024 × 768) display compliant / FDV1001: VGA (640 × 480) display compliant
Maximum brightness
FDX1001: 600 cd/m2 / FDV1001: 450 cd/m
2
LED backlight LCD panel
The LED backlight provides better power efficiency and reduced power consumption compared to existing
uorescent backlight LCD panels.
No mercury, a hazardous substance, is used.
Analog signal support
PC signal: D-Sub mini 15 pin connector × 1
- FDX1001: Horizontal scanning frequency 24 kHz - 50 kHz, Vertical scanning frequency 55 Hz - 75 Hz
- FDV1001: Horizontal scanning frequency 24 kHz - 32 kHz, Vertical scanning frequency 56 Hz - 70.5 Hz
Video signal: S-Video/ Video input connector × 1
- Applicable Format NTSC, PAL, SECAM
Crosshair display function
Displays lines (Fine, Circle or Broken Line) as a reference for the position of the image displayed on the monitor.
3-3. Congure other settings (page 17)
Video aspect function
Alters the display range of the input image (overscan).
3-3. Congure other settings (page 17)
1-2. Package Contents
Check that all the following items are included in the packaging box. If any items are missing or damaged,
contact your local dealer.
NOTE
Please retain the packing materials for future transport of the monitor.•
LCD Monitor
AC Adapter
Cable Tie
User’s Manual (Limited Warranty included)
ATTENTION
This product does not include a power cord. Please provide separately a power cord which meets the usage
requirements.
•
•
•
•
•
•
•
•
•
•
•
•
Page 12
10
Chapter 1 Introduction
1-3. Controls and Functions
10
11
1 2 543 6 987
Setting menu
1 button Switches the input signal.
2 button
Displays the Setting menu, xes the setting or adjustment items on each menu,
and saves the setting or adjustment results.
3 button
• Used to select the setting or adjustment items, or to increase or decrease the
adjustment values on each menu.
• When the settings menu is not displayed, pressing
or switches between
displaying and not displaying the crosshair.
4 button Turns the power on or off.
5 Power indicator
Indicates monitor’s operation status.
Blue : Operating
Orange : Power off
6 Power jack (DC-IN) Connects to the AC adapter.
7 Input signal connector D-Sub mini 15-pin connector × 1
8 Input signal connector S-Video input connector × 1
9 Input signal connector Video input connector × 1
10 Cable holder Covers the monitor cables.
11 Cable tie Clinches the cable.
Page 13
11
Chapter 2 Connecting Cables
Chapter 2 Connecting Cables
2-1. Connection Procedures
1
Connects to external equipment compatible with the monitor.
・
When used as a PC monitor
page 11
・
When using video equipment
page 12
● When used as a PC monitor
ATTENTION
When replacing the current monitor with an FDX1001 / FDV1001 monitor, be sure to change the PC settings for
resolution and vertical frequency to those which are available for the FDX1001 / FDV1001 monitor referring to the
resolution table (see below) before connecting the PC.
•
Compatible Resolutions/Frequencies
The monitor supports the following resolutions.
・
FDX1001
Resolution Display Mode Frequency Dot Clock
640 × 400 NEC PC-9801 56 Hz
~
65 MHz
640 × 400 NEC PC-9821 70 Hz
640 × 480 Apple Macintosh 67 Hz
640 × 480 VGA, VESA
~
75 Hz
720 × 400 VGA TEXT 70 Hz
800 × 600 VESA
~
75 Hz
832 × 624 Apple Macintosh 75 Hz
1024 × 768
*1
VESA 60 Hz
*1
Recommended resolution (Set this resolution.)
・
FDV1001
Resolution Display Mode Frequency Dot Clock
640 × 480 Apple Macintosh 67 Hz
~
31 MHz
640 × 480 VGA 60 Hz
Page 14
12
Chapter 2 Connecting Cables
(1) Connect the monitor to the PC with a signal cable that matches the connectors.
After connecting the cable connectors, tighten the screws of the connectors to secure the coupling.
monitor
Signal cable FD-C16 (optional)
D-Sub mini 15-pin
connector
D-Sub mini 15-pin
connector
Signal cable MD-C87 (optional)
PC
or
DVI connector
● When using video equipment
(1) Connect the monitor to the video equipment with a signal cable that matches the connectors.
S-Video cable (Commercially available product)
Video cable (Commercially available product)
or
S-Video
Video
Video equipment
S-Video
Video
monitor
Page 15
13
Chapter 2 Connecting Cables
2
Plug the power cord of the monitor into a power outlet.
(1) Connect the power cord to the AC adapter.
(2) Connect the AC adapter to the Power jack of the monitor, and after that, connect the power plug to a
power outlet.
ATTENTION
This product does not include a power cord. Please provide separately a power cord which meets the usage
requirements.
For the maximum power saving, it is recommended that the Power button be turned off. Unplugging the power cord
completely shuts off power supply to the monitor.
•
•
2-2. Adjusting the Screen Angle
Hold left and right edge of the monitor with both hands, and adjust the tilt and swivel to the best condition
for working.
Page 16
14
Chapter 3 Settings and Adjustments
Chapter 3 Settings and Adjustments
3-1. Basic Operation and Functions
Basic operation of Setting menu
1
Displaying
Setting
Menu
Press .
2
Setting/Adjusting
3
Exiting
Choose [Exit] with or , and press .
NOTE
Keeping pressed for 2 seconds will also exit the Setting menu.•
Page 17
15
Chapter 3 Settings and Adjustments
Functions
The settings adjustable in the Setting menu are as shown below. The availability of items depends on the
input signal.
√
: Congurable ― : Not congurable
Tab Setting / adjustable item PC Video Reference
Color Brightness
√ √
page 16
Contrast
√ √
Black Level
√ √
Sharpness ―
√
Saturation ―
√
Hue ―
√
PC Settings Clock
√
―
Phase
√
―
Position
√
―
Range Adjustment
√
―
Color Mode
√
―
Red/Green/Blue
√
―
Reset
√
―
Reset
√ √
Others Video Aspect ―
√
page 17
Power Save
√ √
Reverse
√ √
Crosshair
√ √
Color
√ √
Width
√ √
Beep
√ √
Language
√ √
Information
√ √
Page 18
16
Chapter 3 Settings and Adjustments
3-2. Color Adjustment
This will perform color adjustments.
Please switch between the input screens you want to adjust and adjust them one by one.
Adjustable item / adjustable value Adjusting
Brightness 0 - 30 Adjusts the brightness of the backlight.
Contrast 0 - 30 Adjusts the contrast.
Black Level 0 - 30 Adjusts the image brightness.
Sharpness Off/Low/High Adjusts the image outlines.
Saturation -30 - +30 Adjusts the saturation.
Hue -30 - +30 Adjusts the hue.
PC Settings
1
Clock Adjust this when vertical bars appear.
Phase Adjust this when the screen appears to icker or blur.
Position Adjust this when the display positioning is misaligned.
Range Adjustment Provides automatic adjustment when you want every
color gradients displayed.
Color Mode
2
1/2/3 Select Color Mode (1/2/3) to adjust the colors of red,
green and blue in several modes.
Red/Green/
Blue
0 - 128
Reset Resets the state adjusted with [PC Settings] to the
factory default.
Reset Resets the state adjusted with the [Color] tab to the
factory default (excluding [PC Settings]).
*1
This setting becomes available when a PC is connected to the monitor. Please adjust with a PC when display and color adjustments
are required.
*2
Perform [Range Adjustment] before adjusting Color Mode.
Page 19
17
Chapter 3 Settings and Adjustments
3-3. Congure other settings
This will congure other settings.
Setting item / setting value Setting
Video Aspect Nomal/100% Congures the display range of the input image (overscan).
“
Normal”: Displays the input image with the
outmost parts slightly cut off.
* This is how display devices
normally display images.
“
100 %
”
: Displays the entire input image on
the screen.
* Because a part of the image
which normally gets cut off is
displayed as well, noise may be
visible around the outmost parts,
depending on the input signal.
Power Save Disable/Enable Automatically turns off the power supply if no video signal has
been received for 15 minutes during PC or video viewing.
Reverse Off/On Displays the image upside down (180 degree rotation).
Crosshair Off/Fine/Circle/
Broken Line
Displays a crosshair as a reference for the position of the image.
“Fine” “Circle” “Broken Line”
(When the settings menu is not displayed, pressing or
switches between displaying and not displaying the crosshair.)
Color When “Fine” is
selected:
Black/White/Red/
Green
When “Circle” or
“Broken Line” is
selected:
Black/White
Congures the color of the crosshair.
Width Narrow/Wide Congures the thickness of the crosshair’s lines.
Beep Off/On Sets button press sounds and connection error sounds to on or
off.
Short beep• :
- When , or is pressed.
- When an item is selected with .
- When a maximum or minimum value is
set with or .
Long beep• :
When registration is performed with .
2 short beeps• : When the Setting menu is displayed and
is pressed.
4 short beeps• : - When there is no input signal.
- When a frequency out of the specied
range is received.
Language
/English Congures the displayed Setting menu and message language.
Information Reviews the input signals, usage time and model name.
Page 20
18
Chapter 4 Troubleshooting
Chapter 4 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local dealer.
Common
Problems Possible cause and remedy
No picture
Power indicator does not light.•
Check whether the power cord is connected correctly.
If the problem persists, turn off the power, and then turn
it on again a few minutes later.
•
•
Power indicator lights orange.•
Press .•
Power indicator lights blue.• Check whether the power of the connected device is
turned on.
Switch the input signal.
Set each adjusting value in [Brightness] and [Contrast] to
higher level. (see page 16)
•
•
•
The screen is too bright or too dark.• Adjust using [Brightness] or [Contrast]. (The LCD
monitor backlight has a xed life span. When the screen
becomes dark or begins to icker, contact your local
dealer.) (see page 16)
•
Green/red/blue/white dots or defective
dots remain on the screen.
This is due to LCD panel characteristics and is not a
failure.
•
Interference patterns or pressure marks
remain on the screen.
Leave the monitor with a white or black screen. The
symptom may disappear.
•
Afterimages appear. Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.
When displaying the same image for extended periods of
time, please set up the screen saver and/or make use of
the power saving function.
•
•
When displaying on a PC screen
Problems Possible cause and remedy
The message below appears. This message appears when the signal is not input
correctly even when the monitor functions properly.
•
This message appears when no signal
is input.
Ｎｏ
Ｓｉｇｎａｌ
ＰＣ
• The message shown left may appear, because some
PCs do not output the signal soon after power-on.
Check whether the PC is turned on.
Check whether the signal cable is connected properly.
•
•
•
The message shows that the input
signal is out of the specied frequency
range.
Ｓｉｇｎａｌ
Ｅｒｒｏｒ
ＰＣ
• Check whether the signal setting of your PC matches
the resolution and the vertical frequency settings for the
monitor. (see page 20, 21) (Current input signal can be
checked in [Information].)
Reboot the PC.
Select an appropriate display mode using the graphics
board’s utility. Refer to the manual of the graphics board
for details.
•
•
•
Display position is incorrect. Adjust image position using [Position]. (see page 16)•
Vertical bars appear on the screen or a
part of the image is ickering.
Adjust using [Clock]. (see page 16)•
Whole screen is ickering or blurring. Adjust using [Phase]. (see page 16) •
Characters are blurred. This may occur when a non-complying high-resolution
signal is input. Check the PC settings and change the
resolution which complies with the monitor.
•
Page 21
19
Chapter 5 Reference
Chapter 5 Reference
5-1. Attaching an Arm
The stand can be removed and replaced with an arm (or another stand) to be attached to the monitor. Use
an arm or stand of EIZO option.
ATTENTION
When attaching an arm or stand, follow the instructions of their user’s manual.
When using another manufacturer’s arm or stand, conrm the following in advance and select one conforming to
the VESA standard. Use the M4 × 12 mm screws in use by this monitor.
- Clearance between the screw holes : 100 mm × 100 mm
- Thickness of plate : 2.6 mm
- Strong enough to support weight of the monitor unit (except the stand) and attachments such as cables.
Use the screws as described below.
Connect the cables after attaching an arm or a stand.
Since the monitor and arm are so heavy, dropping them may result in injury or equipment damage.
Do not turn the monitor lengthwise.
•
•
•
•
•
[Attachment Procedure]
1
Lay the LCD monitor on a soft cloth spread over on a stable surface with the
panel surface facing down.
2
Remove the stand.
Prepare a screwdriver. Unscrew the four screws securing the unit and the stand with thescrewdriver.
3
Attach the monitor to the arm or stand.
Secure the monitor to the arm or stand using the screws specied in the user’s manual of the arm or stand.
Page 22
20
Chapter 5 Reference
5-2. Specications
FDX1001
LCD Panel Size 10.4-inch (260 mm) TFT color LCD
Surface treatment Anti-glare hard coating
Surface hardness 3H
Viewing angle Horizontal 160°, Vertical130° (CR : 10 or more)
Dot Pitch 0.2055 mm
Display Area (H × V) 210.4 mm × 157.8 mm
Resolution 1024 dots × 768 lines
Max. Display Color Approx. 16.7 million colors
PC input Horizontal Scan Frequency 24-50 kHz
Vertical Scan Frequency 55-75 Hz (Non-interlace)
Max. Dot Clock 65 MHz
Input Signal Connector D-Sub mini 15-pin × 1
Input Signal (Sync) Separate, TTL, positive
/ negative
Input Signal (Video) Analog, Positive (0.7Vp-p/75Ω)
Max. Video Signal Memory 15 (preset : 13)
Plug and Play VESA DDC 2B/EDID structure 1.3
Video input Applicable Format NTSC, PAL, SECAM
Input Signal Connector DIN mini 4 pin/ Pin jack × 1
Input Signal Level DIN mini 4 pin : Y 1.0Vp-p/75Ω, C 0.28Vp-p/75Ω
Pin jack : 1.0Vp-p/75Ω
Power Supply AC adapter (AC) : 100-240VAC±10%, 50/60Hz, 0.3-0.2 A (Max.)
Main unit (DC) : 12VDC±10%, 0.9 A
Power
Consumption
Screen Display On AC adapter (AC) : 13 W or less
Main unit (DC) : 11 W or less
Power Off AC adapter (AC) : 1.3 W or less
Main unit (DC) : 0.5 W or less
Dimensions
(Width) ×
(Height) ×
(Depth)
Main unit 252 mm
(9.9 inch) × 255 mm (10 inch) × 175 mm (6.9 inch)
Main unit (without stand) 252 mm (9.9 inch) × 216 mm (8.5 inch) × 43 mm (1.69 inch)
Mass Main unit Approx. 3.6 kg (7.9 lbs.)
Main unit (without stand) Approx. 2.0 kg (4.4 lbs.)
Movable
range
Tilt 30°Up, 0°Down
Swivel 35°Right, 35°Left
Environmental
Conditions
Temperature Operating temperature : 0 °C - 40 °C (32 °F - 104 °F)
Storage temperature : -20 °C - 60 °C (-4 °F - 140 °F)
Humidity Operating humidity : 20% - 80% R.H. (no condensation)
Storage humidity : 10% - 80% R.H. (no condensation)
Pressure Operating : 700 hPa - 1060 hPa
Storage : 200 hPa - 1060 hPa
Page 23
21
Chapter 5 Reference
FDV1001
LCD Panel Size 10.4-inch (260 mm) TFT color LCD
Surface treatment Anti-glare hard coating
Surface hardness 3H
Viewing angle Horizontal 160°, Vertical140° (CR : 10 or more)
Dot Pitch 0.33 mm
Display Area (H × V) 211.2 mm × 158.4 mm
Resolution 640 dots × 480 lines
Max. Display Color Approx. 16.2 million colors
PC input Horizontal Scan Frequency 24-32 kHz
Vertical Scan Frequency 56-70.5 Hz (Non-interlace)
Max. Dot Clock 31 MHz
Input Signal Connector D-Sub mini 15-pin × 1
Input Signal (Sync) Separate, TTL, positive
/ negative
Input Signal (Video) Analog, Positive (0.7Vp-p/75Ω)
Max. Video Signal Memory 10 (preset : 8)
Plug and Play VESA DDC 2B/EDID structure 1.3
Video input Applicable Format NTSC, PAL, SECAM
Input Signal Connector DIN mini 4 pin/ Pin jack × 1
Input Signal Level DIN mini 4 pin : Y 1.0Vp-p/75Ω, C 0.28Vp-p/75Ω
Pin jack : 1.0Vp-p/75Ω
Power Supply AC adapter (AC) : 100-240VAC±10%, 50/60Hz, 0.2-0.15 A (Max.)
Main unit (DC) : 12VDC±10%, 0.7 A
Power
Consumption
Screen Display On AC adapter (AC) : 10 W or less
Main unit (DC) : 9 W or less
Power Off AC adapter (AC) : 1.3 W or less
Main unit (DC) : 0.5 W or less
Dimensions
(Width) ×
(Height) ×
(Depth)
Main unit 252 mm
(9.9 inch) × 255 mm (10 inch) × 175 mm (6.9 inch)
Main unit (without stand) 252 mm (9.9 inch) × 216 mm (8.5 inch) × 43 mm (1.69 inch)
Mass Main unit Approx. 3.4 kg (7.5 lbs.)
Main unit (without stand) Approx. 1.8 kg (4.0 lbs.)
Movable
range
Tilt 30°Up, 0°Down
Swivel 35°Right, 35°Left
Environmental
Conditions
Temperature Operating temperature : 0 °C - 40 °C (32 °F - 104 °F)
Storage temperature : -20 °C - 60 °C (-4 °F - 140 °F)
Humidity Operating humidity : 20% - 80% R.H. (no condensation)
Storage humidity : 10% - 80% R.H. (no condensation)
Pressure Operating : 700 hPa - 1060 hPa
Storage : 200 hPa - 1060 hPa
Page 24
22
Chapter 5 Reference
Main default settings (factory settings)
PC Video
Brightness 30
Contrast 30 15
Black Level 30 15
Sharpness Off
Saturation - 0
Hue - 0
Color Mode 1 Video Aspect Normal
Power Save Enable
Reverse Off
Crosshair Off
Beep On
Language English
Outside Dimensions
unit : mm (inch)
FDX1001
252 (9.9)
212 (8.3)
20 (0.79)
43
35° 35°
30°
18 (0.71)
20 (0.79)
160 (6.3)
216 (8.5)
255 (10)
291 (11.5)
109.5 (4.3) 75 (2.95) 31.5 (1.24)
6.5 (0.26)
36
(1.42)
93 (3.66)
201 (7.9)
175 (6.9)
75 (2.95) 88.5 (3.48)88.5 (3.48)
200 (7.9)
(1.69)
20 (0.79)
Page 25
23
Chapter 5 Reference
FDV1001
252 (9.9)
213 (8.4)
20 (0.79)
43
35° 35°
30°
18 (0.71)
20 (0.79)
160 (6.3)
216 (8.5)
255 (10)
291 (11.5)
109.5 (4.3) 75 (2.95) 31.5 (1.24)
6.5 (0.26)
36
(1.42)
93 (3.66)
201 (7.9)
175 (6.9)
75 (2.95) 88.5 (3.48)88.5 (3.48)
200 (7.9)
(1.69)
20 (0.79)
Connector Pin Assignment
D-Sub mini 15-pin connector
5
1
3
4
2
8
7
6
9
10
12
1314
15
11
Pin No.
Signal
Pin No.
Signal
Pin No.
Signal
1 Red video 6 Red video ground 11 NC*
2 Green video 7 Green video ground 12 Data (SDA)
3 Blue video 8 Blue video ground 13 H. Sync
4 NC* 9 NC* 14 V. Sync
5 Ground 10 Ground 15 Clock (SCL)
(NC*: No Connection)
•
Page 26
24
Chapter 5 Reference
5-3. Glossary
Afterimage
The Afterimage is particular to LCD monitors. When the monitor screen is left on for a long period without
use. The Afterimage can be removed gradually by changing the displayed image.
Clock
The analog input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics
system in use, when the analog input signal is converted to a digital signal for image display. This is called
clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.
Phase
Phase means the sampling timing to convert the analog input signal to a digital signal. Phase adjustment is
made to adjust the timing. It is recommended that phase adjustment be made after the clock is adjusted
correctly.
Range Adjustment
Range adjustment controls the signal output levels to display every color gradation.
It is recommended that range adjustment be made before color adjustment.
Resolution
The LCD panel consists of numerous pixels of specied size, which are illuminated to form images. This
monitor consists of 1024 (FDX1001) / 640 (FDV1001) horizontal pixels and 768 (FDX1001) / 480
(FDV1001) vertical pixels.
At a resolution of 1024 × 768 (FDX1001) / 640 × 480 (FDV1001), all pixels are illuminated as a full
screen (1:1).
Page 27
25
Chapter 5 Reference
5-4. Preset Timing
The following table shows the factory preset video timing of the PC.
ATTENTION
Display position may be deviated depending on the PC connected, which may require screen adjustment using
Setting menu.
If a signal other than those listed in the table is input, adjust the screen using the Setting menu. However, screen
display may still be incorrect even after the adjustment.
When interlace signals are used, the screen cannot be displayed correctly even after screen adjustment using the
Setting menu.
•
•
•
FDX1001
Resolution
Applicable
signal
Frequency Polarity
Dot clock :
MHz
Horizontal :
kHz
Vertical :
Hz
Horizontal Vertical
720 × 400 VGA TEXT 28.33 31.47 70.09 Negative Positive
640 × 480 VGA 25.18 31.47 59.94 Negative Negative
640 × 480 VESA 31.5 37.86 72.81 Negative Negative
640 × 480 VESA 31.5 37.50 75.00 Negative Negative
800 × 600 VESA 36.00 35.16 56.25 Positive Positive
800 × 600 VESA 40.00 37.88 60.32 Positive Positive
800 × 600 VESA 50.00 48.08 72.19 Positive Positive
800 × 600 VESA 49.50 46.88 75.00 Positive Positive
1024 × 768 VESA 65.00 48.36 60.00 Negative Negative
640 × 480 MAC 30.24 35.00 66.67 Negative Negative
832 × 624 MAC 57.28 49.72 74.55 Negative Negative
640 × 400 PC-9801 21.05 24.83 56.42 Negative Negative
640 × 400 PC-9821 AP2 25.18 31.48 70.10 Negative Negative
FDV1001
Resolution
Applicable
signal
Frequency Polarity
Dot clock :
MHz
Horizontal :
kHz
Vertical :
Hz
Horizontal Vertical
720 × 400 VGA TEXT 28.33 31.47 70.09 Negative Positive
640 × 480 VGA 25.18 31.47 59.94 Negative Negative
800 × 600 VESA 36.00 35.16 56.25 Positive Positive
800 × 600 VESA 40.00 37.88 60.32 Positive Positive
1024 × 768 VESA 65.00 48.36 60.00 Negative Negative
640 × 480 MAC 30.24 35.00 66.67 Negative Negative
640 × 400 PC-9801 21.05 24.83 56.42 Negative Negative
640 × 400 PC-9821 AP2 25.18 31.48 70.10 Negative Negative
Page 28
26
LIMITED WARRANTY
LIMITED WARRANTY
EIZO NANAO CORPORATION (hereinafter referred to as “EIZO”) and distributors authorized by EIZO (hereinafter
referred to as the “Distributors”) warrant, subject to and in accordance with the terms of this limited warranty (hereinafter
referred to as the “Warranty”), to the original purchaser (hereinafter referred to as the “Original Purchaser”) who
purchased the product specified in this document (hereinafter referred to as the “Product”) from EIZO or Distributors,
that EIZO and Distributors shall, at their sole discretion, either repair or replace the Product at no charge if the Original
Purchaser becomes aware within the Warranty Period (defined below) that the Product malfunctions or is damaged in the
course of normal use of the Product in accordance with the description in the instruction manual attached to the Product
(hereinafter referred to as the “User’s Manual”).
The period of this Warranty is two (2) years from the date of purchase of the Product (hereinafter referred to as the
“Warranty Period”). EIZO and Distributors shall bear no liability or obligation with regard to the Product in relation to the
Original Purchaser or any third parties other than as provided under this Warranty.
EIZO and Distributors will cease to hold or store any parts of the Product upon expiration of seven (7) years after the
production of such parts is discontinued. In repairing the monitor, EIZO and Distributors will use renewal parts which
comply with our QC standards.
The Warranty is valid only in the countries or territories where the Distributors are located. The Warranty does not restrict
any legal rights of the Original Purchaser.
Notwithstanding any other provision of this Warranty, EIZO and Distributors shall have no obligation under this Warranty
whatsoever in any of the cases as set forth below:
(a) Any defect of the Product caused by freight damage, modification, alteration, abuse, misuse, accident, incorrect
installation, disaster, faulty maintenance and/or improper repair by third party other than EIZO and Distributors;
(b) Any incompatibility of the Product due to possible technical innovations and/or regulations;
(c) Any deterioration of display performance caused by the deterioration of expendable parts such as the LCD panel
and/or backlight, etc. (e.g. changes in brightness, changes in brightness uniformity, changes in color, changes in
color uniformity, defects in pixels including burnt pixels, etc.);
(d) Any defect of the Product caused by external equipment;
(e) Any defect of the Product on which the original serial number has been altered or removed;
(f) Any defect of the Product caused by liquid leaking from battery;
(g) Any normal deterioration of the product, particularly that of consumables, accessories, and/or attachments (e.g.
batteries, buttons, rotating parts, remote control, cables, User’s Manual, etc.); and
(h) Any deformation, discoloration, and/or warp of the exterior of the product including that of the surface of the LCD
panel.
To obtain service under the Warranty, the Original Purchaser must deliver the Product, freight prepaid, in its original
package or other adequate package affording an equal degree of protection, assuming the risk of damage and/or loss
in transit, to the local Distributor. The Original Purchaser must present proof of purchase of the Product and the date of
such purchase when requesting services under the Warranty.
The Warranty Period for any replaced and/or repaired product under this Warranty shall expire at the end of the original
Warranty Period.
EIZO OR DISTRIBUTORS ARE NOT RESPONSIBLE FOR ANY DAMAGE TO, OR LOSS OF, DATA OR OTHER
INFORMATI O N STO R E D IN ANY MEDIA OR ANY PART OF ANY PRO D U C T RETU R N E D TO EIZO OR
DISTRIBUTORS FOR REPAIR.
EIZO AND DISTRIBUTORS MAKE NO FURTHER WARRANTIES, EXPRESSED OR IMPLIED, WITH RESPECT TO
THE PRODUCT AND ITS QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR
USE. IN NO EVENT SHALL EIZO OR DISTRIBUTORS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL,
CONSEQUENTIAL OR OTHER DAMAGE WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR
LOSS OF PROFIT, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR ANY OTHER PECUNIARY
LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT OR IN ANY CONNECTION WITH THE
PRODUCT, WHETHER BASED ON CONTRACT, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE, EVEN
IF EIZO OR DISTRIBUTORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THIS EXCLUSION
ALSO INCLUDES ANY LIABILITY WHICH MAY ARISE OUT OF THIRD PARTY CLAIMS AGAINST THE ORIGINAL
PURCHASER. THE ESSENCE OF THIS PROVISION IS TO LIMIT THE POTENTIAL LIABILITY OF EIZO AND
DISTRIBUTORS ARISING OUT OF THIS LIMITED WARRANTY AND/OR SALES.
Page 29
关于电子信息产品污染控制标识
本标识根据「电子信息产品污染控制管理办法」，适用于在中华人民共和国销售的电子信息产品。标识中央的
数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项，在自制造日起算的年限内，不会
产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。
•
有毒有害物质或元素的名称及含量
部件名称 有毒有害物质或元素
铅
（Pb）
汞
（Hg）
镉
（Cd）
六价铬
（Cr（VI））
多溴联苯
（PBB）
多溴二苯醚
（PBDE）
印刷电路板 × ○ ○ ○ ○ ○
机箱 ○ ○ ○ ○ ○ ○
液晶显示器 × ○ ○ ○ ○ ○
其他 × ○ ○ ○ ○ ○
○： 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的限量要求以下。
×： 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的限量要求。
( 企业可在此处 , 根据实际情況对上表中打“×”的技术原因进行进一步说明 )
Page 30
Loading...