Eizo CG19 User Manual

SAFETY SYMBOLS

PRECAUTIONS

1. INTRODUCTION
1-1.Features
1-2.Package Contents
1-3.Controls & Connectors

2. CABLE CONNECTION
2-1.Before Connecting
2-2.Connecting the Signal

Cable (D-Sub or DVI)

2-3.Connecting the Signal

Cable (ADC)

2-4.Connecting Two PCs to

the Monitor

2-5.How to remove the Tilt

Stand

3. ScreenManager
3-1.How to use the

ScreenManager

3-2.ScreenManager

Adjustments and Settings
3-3.FineContrast
3-4.Useful Functions

4. ADJUSTMENT
4-1.Screen Adjustment
4-2.Displaying a low

resolution
4-3.Color Adjustment
4-4.Power-save Setup

5. MAKING USE OF USB
(Universal Serial Bus)

6. TROUBLESHOOTING

7. CLEANING

This manual is checked under the browser settings shown
below. Text size can change for another one through
browser setting.

Microsoft Internet Exproler:

Text size: Medium
Encoding: Western European

8. SPECIFICATION

9. GLOSSARY

APPENDIX/ ANHANG/
ANNEXE

About TCO'03 (Applicable to
gray)
About TCO'99 (Applicable to
black)
FCC Declaration of
Conformity
Hinweis zur Ergonomie /
Recycle Auskunft / Hinweise
zur Auswahl des richtigen
Schwenkarms für Ihren
Monitor

This manual uses the safety symbols below. They denote critical information. Please read them
carefully.

WARNING

Failure to abide by the information in a WARNING may result in serious
injury and can be life threatening.

CAUTION

Failure to abide by the information in a CAUTION may result in moderate
injury and/or property or product damage.

Indicates a prohibited action.

Indicates to ground for safety.

Copyright© 2004 EIZO NANAO CORPORATION All rights reserved.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any
form or by any means, electronic, mechanical, or otherwise, without the prior written
permission of EIZO NANAO CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or
information confidential unless prior arrangements are made pursuant to EIZO NANAO
CORPORATION's receipt of said information Although every effort has been made to ensure
that this manual provides up-to-date information, please note that EIZO monitor specifications
are subject to change without notice.

ENERGY STAR is a U.S. registered mark.
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
VGA is a registered trademark of International Business Machines Corporation.
DPMS is a trademark and VESA is a registered trademark of Video Electronics Standards
Association.
Windows is a registered trademark of Microsoft Corporation.
PowerManager is a trademark of EIZO NANAO CORPORATION.

ScreenManager, ColorEdge and EIZO are registered trademarks of EIZO NANAO
CORPORATION in Japan and other countries.

As an ENERGY STAR® Partner, EIZO NANAO CORPORATION has
determined that this product meets the ENERGY STAR guidelines for
energy efficiency.

IMPORTANT!

● This product has been adjusted specifically for use in the region to which it

was originally shipped. If operated outside the region to which it was originally
shipped, the product may not perform as stated in the specifications.

● To ensure personal safety and proper maintenance, please read this section and

the caution statements on the unit (refer to the figure below).

[Location of the Caution Statements]

If the unit begins to emit smoke, smells like something is burning, or
makes strange noises, disconnect all power connections immediately
and contact your dealer for advice.

Attempting to use a malfunctioning unit may result in fire, electric shock,
or equipment damage.

Do not open the cabinet or modify the unit.

Opening the cabinet or modifying the unit may result in fire, electric shock,
or burn.

Refer all servicing to qualified service personnel.

Do not attempt to service this product yourself as opening or removing
covers may result in fire, electric shock, or equipment damage.

Keep small objects or liquids away from the unit.

Small objects accidentally falling through the ventilation slots into the
cabinet or spillage into the cabinet may result in fire, electric shock, or
equipment damage.
If an object or liquid falls/spills into the cabinet, unplug the unit
immediately. Have the unit checked by a qualified service engineer before
using it again.

Place the unit at the strong and stable place.

A unit placed on an inadequate surface may fall and result in injury or
equipment damage.
If the unit falls, disconnect the power immediately and ask your dealer for
advice. Do not continue using a damaged unit. Using a damaged unit may
result in fire or electric shock.

Set the unit in an appropriate location.

Not doing so may result in fire, electric shock, or equipment damage.

● Do not place outdoors.

● Do not place in the transportation system (ship, aircraft, trains,

automobiles, etc.)

● Do not place in a dusty or humid environment.

● Do not place in a location where the steam comes directly on the

screen.

● Do not place near heat generating devices or a humidifier.

To avoid danger of suffocation, keep the plastic packing bags away
from babies and children.

Use the enclosed power cord and connect to the standard power outlet
of your country.

Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.

To disconnect the power cord, grasp the plug firmly and pull.

Tugging on the cord may damage and result in fire or electric shock.

The equipment must be connected to a grounded main outlet.

Not doing so may result in fire or electric shock.

Use the correct voltage.

* The unit is designed for use with a specific voltage only. Connection to
another voltage than specified in this User's Manual may cause fire, electric
shock, or equipment damage.

* Do not overload your power circuit, as this may result in fire or electric
shock.

Handle the power cord with care.

* Do not place the cord underneath the unit or other heavy objects.

* Do not pull on or tie the cord.

If the power cord becomes damaged, stop using it. Use of a damaged cord
may result in fire or electric shock.

Never touch the plug and power cord if it begins to thunder.

Touching them may result in electric shock.

When attaching an arm stand, please refer to the user's manual of the
arm stand and install the unit securely with the enclosed screws.

Not doing so may cause the unit to become unattached, which may result in
injury or equipment damage. When the unit is dropped, please ask your
dealer for advice. Do not continue using a damaged unit. Using a damaged
unit may result in fire or electric shock. When reattaching the tilt stand,
please use the same screws and tighten them securely.

Do not touch a damaged LCD panel directly with bare hands.

The liquid crystal that may leak from the panel is poisonous if it enters the
eyes or mouth.
If any part of the skin or body comes in direct contact with the panel,
please wash thoroughly. If some physical symptoms result, please consult
your doctor.

Follow local regulation or laws for safe disposal.

The backlight of the LCD panel contains mercury.

Handle with care when carrying the unit.

Disconnect the power cord and cables when moving the unit. Moving the
unit with the cord attached is dangerous. It may result in injury.

When handling the unit, grip the bottom of the unit firmly with both
hands ensuring the panel faces outward before lifting.

Dropping the unit may result in injury or equipment damage.

Do not block the ventilation slots on the cabinet.

* Do not place any objects on the ventilation slots.

* Do not install the unit in a closed space.

* Do not use the unit laid down or upside down.

Blocking the ventilation slots prevents proper airflow and may result in
fire, electric shock, or equipment damage.

Do not touch the plug with wet hands.

Doing so may result in electrical shock.

Use an easily accessible power outlet.

This will ensure that you can disconnect the power quickly in case of a
problem.

Periodically clean the area around the plug.

Dust, water, or oil on the plug may result in fire.

Unplug the unit before cleaning it.

Cleaning the unit while it is plugged into a power outlet may result in
electric shock.

If you plan to leave the unit unused for an extended period, disconnect
the power cord from the wall sochekt after turning off the power
switch for the safety and the power conservation.

In order to suppress the luminosity change by long-term use and to
maintain the stable luminosity, use of a monitor in lower brightness is
recommended.

The screen may have defective pixels. These pixels may appear as slightly
light or dark area on the screen. This is due to the characteristics of the
panel itself, and not the product.

The backlight of the LCD panel has a fixed life span. When the screen
becomes dark or begins to flicker, please contact your dealer.

Do not press on the panel or edge of the frame strongly, as this may result
in damage to the screen. There will be prints left on the screen if the
pressed image is dark or black. If pressure is repeatedly applied to the
screen, it may deteriorate or damage your LCD panel. Leave the screen
white to decrease the prints.

Do not scratch or press on the panel with any sharp objects, such as a
pencil or pen as this may result in damage to the panel. Do not attempt to
brush with tissues as this may scratch the LCD panel.

Thank you very much for choosing an EIZO Color Monitor.

● The exclusive use calibration software caliblates the monitor characteristics

and generate colorprofile.

● Dual inputs compliant

● DVI Digital input (TMDS) compliant.

● ADC (Apple Display Connector) inputs compliant.

● [Horizontal scanning frequency]

Analog: 30 - 82 kHz
Digital: 30 - 65 kHz
[Vertical scanning frequency]
Analog: 49 - 86 Hz Vertical (1280 x 1024: 49 - 75 Hz)
Digital: 59 - 61 Hz (VGA text: 69 - 71 Hz))
[Resolution] 1280 dots x 1024 lines

● Support to sRGB standard

● The height adjustable stand incorporated

● Ultra slim bezel incorporated

● The Portrait/Landscape display capability

● Attaching the "Adjustment Certificate" to describe the monitor color

characteristics individually.

Please contact your local dealer for assistance if any of the listed items are missing or
damaged.

* LCD Monitor * User's Manual (in the CD-ROM)
* Power Cord * Calibration software

"ColorNavigator" (in the CD-ROM)
* Signal Cable (FD-C35/FD-C39) * Setup Guide
* Signal Cable (FD-C16) * ColorNavigator Quick Reference
* EIZO USB Cable (MD-C93) * LIMITED WARRANTY

*EIZO LCD Utility Disk * Adjustment Certificate

* Please retain the packing materials for future transference.

Front

(1)

ScreenManager

®

(2) Main Power Switch
(3) Input Signal Selection Button
(4)

Mode Button

*1

(5) Auto Adjustment Button
(6) Enter Button
(7)

Control Buttons (Up, Down, Left, Right)
(8) Power Button
(9)

Power Indicator

*3

Blue Operation
Yellow Power saving

*2

Flashing yellow

Power save mode Digital only

(2 times for each)
Flashing yellow slowly Power is off (Main power is on)
Off Power off

*1

Pressing the Mode button once allows you to display a FineContrast menu.

Pressing the Mode button more than once allows you to select a FineContrast

mode. (The main menu of ScreenManager and the FineContrast menu cannot be

displayed at the same time.)

*2 These buttons are changed to Up, Left, Right, Down in case of selecting

"Portrait" for <Orientation> of ScreenManager <Others>.

*3 Blue lighting, when the screen is displayed (Operation mode), is made to non-

light, see "Power Indicator "

Regarding the power indicator for the "Off Timer", see "

3-4. Useful Functions".

Rear

(10)

Height Adjustable Stand (Detachable)

(11)

Security Lock Slot

(12) DVI-I Input Connector (SIGNAL 1, SIGNAL 2)
(13) USB Port (1 Upstream)
(14) USB Port (2 Downstream)
(15) Power Connector

*5

*4

*4 The LCD monitor has the capability of the Portrait/Landscape display. (The

panel pivots in the clockwise direction 90°.) The LCD monitor can be used with

an optional arm stand by removing the stand. (see "2-5. How to remove the Tilt

Stand").

*5 Allows for connection of a security cable. This lock supports Kensington's

MicroSaver security system.

For further information, please consult:

Kensington Technology Group

2855 Campus Drive, San Mateo, CA 94403 USA

Tel: [phone], x3348

Intl: 650-572-2700, x3348 / Fax: [phone]

http://www.kensington.com

Before connecting your monitor to the PC, change the display screen settings
(resolution and frequency) in accordance with the charts below.

* When your computer and display support VESA DDC, the suitable resolution

and the refresh rate are set by just plugging your display into the computer
without any manual settings.

Analog Input

Resolution Frequency Dot Clock Remarks

640 x 480 ~ 85 Hz
640 x 480 67 Hz Apple Macintosh
720 x 400 70 Hz VGA TEXT
720 x 480 60 Hz VESA
800 x 600 ~ 85 Hz VESA

832 x 624 75 Hz Apple Macintosh
1024 x 768 ~ 85 Hz VESA
1152 x 864 75 Hz VESA
1152 x 870 75 Hz Apple Macintosh
1152 x 900 ~ 76 Hz SUN WS
1280 x 960 60 Hz VESA
1280 x 960 75 Hz Apple Macintosh

1280 x1024 ~75 Hz VESA
1280 x1024 67 Hz SUN WS

135 MHz

(Max.)

VGA, VESA

Digital Input

The monitor supports the following resolutions only.

Resolution Frequency Dot Clock Remarks

640 x 480 60 Hz

720 x 400 70 Hz VGA TEXT

720 x 480 60 Hz VESA Safe Mode

800 x 600 60 Hz VESA
1024 x 768 60 Hz VESA

1280 x 1024 60 Hz VESA

108 MHz

(Max.)

VGA

* Be sure that the power switches of both the PC and the monitor are OFF.

1.Plug the signal cable into the connector at the rear of the monitor
and the other end of the cable into the video connector on the PC.

After connecting, secure the connection with the screw-in fasteners.

Analog Input

Signal Cable Connector PC

Signal Cable (FD-C16
enclosed)

Signal Cable (FD-C16
enclosed) + Macintosh
Adapter (Optional)

Digital Input

Signal Cable Connector PC

Signal Cable (FD-C35/FD­C39 enclosed)

Video Output
Connector D-Sub 15
pin
Input Connector
(monitor) / DVI

Video Output
Connector D-Sub 15
pin
Input Connector
(monitor) / DVI

Video Output
Connector / DVI
Input Connector
(monitor) / DVI

Standard graphics card
Macintosh G3 (Blue &
White) /Power Mac G4 (VGA)

Macintosh

Digital graphics card
Power Mac G4 / G5 (DVI)

2.Plug the power cord into the power connector on the rear of the
monitor.

3.Lead the power cord and signal cable into the cable holder at rear
of the monitor.

* The cables are recommended to lead with slight sag for the smooth motion of the

stand and the Portrait/Landscape display.

4.Plug the other end of the power cord into a power outlet.

The monitor's power indicator will flash yellow slowly.

WARNING

Use the enclosed power cord and connect to the standard
power outlet of your country.

Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.

The equipment must be connected to a grounded main outlet.

Not doing so may result in fire or electric shock.

5.Turn on the monitor's power button and then switch on the PC's
power.

The monitor's power indicator will light up (blue).
If an image does not appear, refer to the "6. TROUBLESHOOTING" for advice.

Whenever finished, turn off the PC and the monitor.

* When turning on the monitor, the kid of the input signal (Signal1 or 2/Analog or

Digital) is displayed for a few seconds on the right top corner of the screen.
* Adjust brightness of the screen depending on the brightness of your environment.
* Be sure to take adequate rests. A 10-minute rest period each hour is suggested.

When connecting a Power Mac G4 / G5 through ADC (Apple Display Connector),
change the input signal settings of monitor in advance to turn on the Power Mac.

* Be sure that the power switches of both the PC and the monitor are OFF.

1.Plug the signal cable into the connector at the rear of the monitor
and the other end of the cable into the video connector on the PC.

After connecting, secure the connection with the screw-in fasteners.

To input the Signal through ADC

Signal Cable Connector PC

Signal Cable (FD-C35/FD­C39 enclosed) +ADC-DVI
display adapter
(commercially available)

* ADC-DVI display adapter is required if the monitor connects to Power Mac G4 /

G5. The adapter is commercially available.

Video Output
Connector / ADC
Input Connector
(monitor) / DVI

Power Mac G4 / G5 (ADC)

2.Plug the power cord into the power connector on the rear of the
monitor.

3.Lead the power cord and signal cable into the cable holder at rear
of the monitor.

* The cables are recommended to lead with slight sag for the smooth motion of the

stand and the Portrait/Landscape display.

4.Plug the other end of the power cord into a power outlet.

The monitor's power indicator will flash yellow slowly.

WARNING

Use the enclosed power cord and connect to the standard
power outlet of your country.

Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.

The equipment must be connected to a grounded main outlet.

Not doing so may result in fire or electric shock.

5.Press the power button while pressing the Input Signal Selection
button.

The Input Selection menu is appeared on the screen.

6.Change the input selection setting of the connector in the Input
Selection menu to "ADC".

Press Enter button to complete the setting and the menu closes.

7.Switch on the PC's power.

The monitor's power indicator will light up (blue).
If an image does not appear, refer to the "6. TROUBLESHOOTING" for advice.

Whenever finished, turn off the PC and the monitor.

* When turning on the monitor, the kid of the input signal (Signal1 or 2/Analog or

Digital) is displayed for a few seconds on the right top corner of the screen.
* Adjust brightness of the screen depending on the brightness of your environment.
* Be sure to take adequate rests. A 10-minute rest period each hour is suggested.
* When changing the signal connector except ADC, open the Input Selection menu

again and change the setting to "Standard".
* To <Reset> the settings in ithe <Others> menu through ScreenManager, the

settings of Input Selection will revert to the default setting.

Two PCs can be connected to the monitor through DVI-I connector and D-sub mini 15
pin connector on the back of the monitor.

PC 1 PC 2

(EX.1)DigitalADC

Signal Cable (FD­C35 / FD-C39
enclosed) +ADC­DVI display adapter
(commercially
available)

Signal Cable (FD­C16 enclosed)

D-Sub
mini 15
pin

Analog

(EX.2)DigitalADC

(EX.3)DigitalDVI-D

(EX.4)DigitalDVI-D

Signal Cable (FD­C35 / FD-C39
enclosed) +ADC­DVI display adapter
(commercially
available)

Signal Cable (FD­C35 / FD-C39
enclosed)

Signal Cable (FD­C35 / FD-C39
enclosed)

Signal Cable (FD­C16 enclosed) +
Macintosh Adapter
(Optional)

Signal Cable (FD­C16 enclosed)

Signal Cable (FD­C16 enclosed) +
Macintosh Adapter
(Optional)

D-Sub 15
pin

D-Sub
mini 15
pin

D-Sub 15
pin

Analog

Analog

Analog

Selecting the Active Input

The Input Signal Selection button on the control panel can be used to select either
SIGNAL 1 or SIGNAL 2 as the active input at any time. Every time the button is
pressed, the input changes. When switching the signal, the kind of the input signal
(Signal 1 or 2/ Analog or Digital) is displayed for a few seconds on the right top corner
of the screen.

The Priority Input Signal

This function is used to select which PC will have priority to control the monitor when
utilizing two PCs. The monitor constantly checks the input signals and switches
automatically in accordance with the "Input Priority" setting (see table below). Once a
priority is set, whenever a change of signal is detected at the selected input, the
monitor will switch the input to that signal.
In this case of only one signal being present at either input, the monitor automatically
detects and displays that signal.

Priority

Settings

(SIGNAL1)

(SIGNAL2)

Performance

1

If signals from both inputs are present, the monitor gives
preference of Signal 1 in the following cases.

● When the power of the monitor is turned ON.

● When the signal input to Signal 1 is changed even if active

input was Signal 2.

2

If signals from both inputs are present, the monitor gives
preference to Signal 2 in the following cases.

● When the power of the monitor is turned ON.

● When the signal input to Signal 2 is changed even if active

input was Signal 1.

Manual The monitor will not detect signals automatically in this mode.

Select the active input by pressing the input signal selection button
on the monitor's control panel.

* When "1" or "2" is selected, the power saving mode of the monitor activates only

if both PCs are in power saving mode.

The LCD monitor can be used with an arm by removing the tilt stand and attaching the
arm or stand to the LCD monitor.

Using our optional arm or stand is recommended. (Ask your local dealer for
information.)

* If you will use the arm or stand of other manufacturers, confirm the followings to

the manufacturers before selecting.

● Hole spacing on the arm mounting: 100 mm x 100 mm (VESA

compliant)

● Supportable Weight: Total weight of the monitor (without stand) and

attaching equipment such as a cable

● TÜV/GS approved arm or stand

* Please connect cables after attaching an arm stand.

Setup Procedure

1.Hold the center of the stand mounting cover and slide them
rightward or leftward to remove the mounting cover.

2.Lay the LCD monitor down. Do not scratch the panel.

3.Remove the tilt stand by loosening the screws. (4 pcs of M4 x 15
mm)

4.Attach an arm stand to the LCD monitor securely.

ScreenManager allows you to adjust screen performance though the main menu and
select a FineContrast mode easily.

* Main Menu and FineContrast menu cannot be activated at the same time.

1.Entering the ScreenManager

Press the Enter button once to display the main menu of the ScreenManager.

2.Making Adjustments and Settings

(1) Select the desired sub menu icon using the Control buttons and press the Enter

button. The sub menu appears.

(2) Use the Control buttons to select the desired setting icon and press the Enter

button. The setting menu appears.

(3) Use the Control buttons to make all required adjustments and press the Enter

button to save the settings.

3.Exiting the ScreenManager

(1) To return to the main menu, select the <Return> icon or press the Down button

twice, followed by the Enter button.

(2) To exit the ScreenManager, select <Exit> icon or press the Down button twice,

followed by the Enter button.

* Double clicking the Enter button at any time also exits the ScreenManager menu.

FineContrast menu

Pressing the Mode button allows you to select the best suited mode for screen
display from 3 FineContrast modes; Custom, sRGB and CAL. To exit the menu,
press the Enter button.

The following table shows all the ScreenManager's adjustment and setting menus."*"
indicates adjustments of analog input only and "**" indicates digital input only.

Main menu Sub menu Reference

Screen Clock * 4-1. Screen Adjustment

Phase *
Position *
Resolution *
Range Adjustment *
Smoothing
Signal Filter *

Color (Custom)*1Brightness 4-3. Color Adjustment

Temperature
Gamma
Saturation
Hue
Gain
6 Colors

Reset

PowerManager DVI DMPM ** 4-4. Power-save Setup

VESA DPMS *

Others Screen Size 4-2.Displaying a low resolutions

Border Intensity
Input Priority

Off Timer

Beep

Menu Size Change the size of the menu.
Menu

Position

Menu
Settings

Menu Off
Timer

Translucent

Orientation

Power Indicator

Select the priority input signal.
Set the monitor's off timer to on or

off.

Set the monitor's beeper to on or
off.

Adjust the menu position.

Set the menu displaying time.

*2

Set the transparency of the
background.

Change the orientation of the
ScreenManager for monitor's
portrait position.

Make non-light for blue lighting
when the screen is displayed (see
"Power Indicator setting").

Reset

Information

Information

settings.

Review the ScreenManager's
settings, model name, serial

number and usage time.

Return to the factory default

Language English, German, French,

Spanish, Italian, Swedish

Select the ScreenManager's
language.

and Japanese

*1 The adjustable functions on the <Color> menu depend on the selected

FineContrast mode. The above table shows the sub menus when the "Custom"
mode is selected (see "4-3. Color Adjustment").

*2 The displaying time of the FineContrast menu cannot be changed.
*3 Due to the inspection on the factory, the usage time may not "0 hour" at

shipping.

*3

This function allows you to select the best suited mode for screen display.

To select the Mode

Pressing the Mode button allows you to select the best suited mode for screen display
from 3 FineContrast modes; Custom, sRGB and CAL. Color settings each mode can
be adjusted by using the <Color> menu of the ScreenManager.

Exit

Press the Enter button to exit the menu.

FineContrast Mode

Selectable FineContrast modes are as follows.

Custom To adjust the color settings according to your preference.
sRGB
CAL The mode only for calibration software

To display the screen images based on those original colors (ex. over
the Internet).

Color Adjustment of the Mode Settings

<Brightness>, <Temperature> and <Gamma> settings can be ajusted on the
FineContrast menu. Select the desired function icon with the Up/Down Control buttons
and adjust with the Left/Right Control buttons. (Setting(s) of <Temperature> and/or
<Gamma> is defined as standard default in some modes.

Detailed Adjustments

The detailed color settings of each mode can be adjusted by using the <Color> menu
of the ScreenManager.

* "CAL" mode can be adjusted only by Calibration Software "ColorNavigator" .

Adjustment Lock

Use the "Adjustment Lock" function to prevent any accidental changes.

● Settings in the ScreenManager

Locked function

Unlocked function

● Auto Adjustment Button

● Selecting of the FineContrast mode by the Mode

button / Adjustments

● Input Signal Selection Button

[To lock]

Switch off the monitor's power by the power button on the front control panel. Press on
the Auto Adjustment button while switching on the monitor's power.

[To unlock]

Switch off the monitor's power by the power button on the front control panel, then
hold Down the Auto Adjustment button once again and turn the power back on.

Off Timer

The off timer function causes the monitor to automatically enter a power off state after
a predetermined amount of time has lapsed. This function was created to reduce

afterimage characteristics that are particular to LCD monitors when the monitor screen

is left on for a long period without use.

[Procedure]

(1) Select <Off Timer> in the ScreenManager <Others> menu.
(2) Select "Enable" and press the Right and Left buttons to adjust the "On

Period" (1 to 23 hours).

[Off Timer System]

PC Monitor Power Indicator
On Period (1H - 23H) Operation Blue
Last 15 min. in "On

period"
"On period" expired Power off Flashing yellow slowly

*1 Advance notice (Power Indicator flashing blue) will be given 15 minutes before

the monitor automatically enters the "Power Off" mode. To delay entering the
"Power Off" mode, press the power button during the advance notice period.
The monitor will continue to operate for an additional 90 minutes.

[Power Resumption Procedure]

Press the power button to return a normal screen.

Advance Notice

*1

Blue Flashing

* The off timer function works while the PowerManager is active, but there is no

advance notice before the monitor's power is switched off.

Power Indicator setting

Light off the power indicator. This function is available for the multiple panels settings.

[Procedure]

(1) Select <Power Indicator> in the ScreenManager <Others> menu.
(2) Select "Disable".

EIZO Logo Disappearing Function

When switching on the power button on the front control panel, the EIZO logo is
displyed for a while. If you desire to display or undisplay this logo, use this function.
(Default is logo appearing.)

[To undisplay]

Switch off the monitor's power by the power button, then hold Down the Enter button
once again and turn the power back on.

[To display]

Switch off the monitor's power by the power button, then hold Down the Enter button
once again and turn the power back on.

Automatically Selecting the Input Signal Function

The monitor will automatically detect the inputted signal of either the connection for
display. (Default: this function is set ("Auto").)

Connecting Two PCs to the Monitor

When the one computer is switched off or entering the power saving mode, the
monitor will automatically display the other signal.

Use the ScreenManager to switch the input signal manually.

[Procedure]

(1) Select <Input Signal> in the <Others> menu.
(2) Select <Manual>.

The monitor displays the digital input image correctly based on its pre-setting
data.

Screen adjustments for the LCD monitor should be used in suppressing screen
flickering and also for adjusting the screen to its proper position. There is only one
correct position for each display mode. It is also recommended to use the
ScreenManager function when first installing the display or whenever changing the
system. For convenience, an easy set-up program installed on the utility disk to assist
in the set-up procedure is provided.

* Allow the LCD monitor to stabilize for at least 20 minutes before making image

adjustments.

Adjustment Procedure

1.Push the Auto Adjustment Button on the control panel.

The message "Your setting will be lost, if you press again now." appears and remains
on the screen for 5 seconds. While the message is on the screen, press the Auto
Adjustment button again to automatically adjust the clock, phase, screen position and
resolution. If you do not wish to do adjust the screen, do not press the Auto
Adjustment button again.

* The Auto sizing function is intended for use on the Macintosh and on AT-

compatible PC running Windows. It may not work properly in either of the
following cases.
When running an AT-compatible PC on MS-DOS (Not windows). The
background color for the "wall paper" or "desktop" pattern is set to black.

If the appropriate screen cannot be made by using the Auto Adjustment
button, adjust the screen through the following procedures. If the appropriate
screen can be made, proceed to step 4.

2.Run the "Screen Adjustment Program".

Having read the "Readme.txt" file, run the "Screen Adjustment Program" in the
enclosed EIZO LCD Utility Disk. Step by step, adjustment is provided by the wizard
guide. (If using the Windows, the program can be directly run from the menu screen of
the CD-ROM.)

* If the user's operating system has no utility disk (e.g. OS/2), we recommend

setting the desktop pattern to that as shown in the diagram on the following.

3.Adjust by using <Screen> menu in the ScreenManager.

(1) Vertical bars appear on the screen

=> Use the <Clock> adjustment.

Select the <Clock> and eliminate the vertical bars by using the Right and Left of
the Control buttons.

Do not continuously press the Control buttons, as the adjustment value will
change quickly and make it difficult to locate the most suitable adjustment point.
If the horizontal flickering, blur or bars appear, proceed to <Phase> adjustment
as follows.

(2) Horizontal bars appear on the screen.

=> Use the <Phase> adjustment.

Select the <Phase> and eliminate the horizontal flickering, blurring or bars by
using the Right and Left buttons.

* Horizontal bars may not completely disappear from the screen depending on the

PC.

(3) The screen position is incorrect.

=> Use the <Position> adjustment.

The correct displayed position of the monitor is decided because the number and
the position of the pixels are fixed. The <Position> adjustment moves the image
to the correct position.

Select <Position> and adjust the position by using the Up, Down, Right and Left
buttons.

If vertical bars of distortion appear after finishing the <Position> adjustment,
return to <Clock> adjustment and repeat the previously explained adjustment
procedure. ("Clock" => "Phase" => "Position").

(4) Screen image is smaller or larger than the actual screen images.

=> Use the <Resolution> adjustment.

Adjustment is needed when the input signal resolution and the resolution now
being displayed are different.

Select <Resolution> and confirm if the resolution now being displayed is the
same as the input resolution. If it is not, adjust the vertical resolution using the
Up and Down button and adjust the horizontal resolution using the Right and
Left buttons.

4.Adjust the output signal range (Dynamic Range) of the signal.
=>

This controls the level of output signal range to display the whole color gradation (256
colors).

[Procedure]

Select the <Range Adjustment> in the ScreenManager and press the Auto Adjustment
button on the control panel to adjust the Range Adjustment.
The screen blanks for a moment and adjusts the color range to display the whole color
gradation of the current output signal.

Use the <Range Adjustment> of <Screen> menu.

The lower resolutions are enlarged to full screen automatically. Using the <Screen
Size> function in the <Others> menu enables to change the screen size.

1.Enlarge the screen size when displaying a low resolution.
=> Select the <Screen Size>.

Select the <Screen Size> in the others menu and select the screen size by using the Up
and Down buttons.

Menu Function

Displays the picture on the screen in full, irrespective of the

Full

Enlarged

Normal Displays the picture at the actual screen resolution.

Example: Displaying 1024 x 768

picture's resolution. Since the vertical resolution and the
horizontal resolution are enlarged at different rates, some
image may appear distorted.

Displays the picture on the screen in full, irrespective of the
picture's resolution. Since the vertical resolution and
horizontal resolution are enlarged at the same rates, some
horizontal or vertical image may disappear.

2.Smooth the blurred texts of the enlarged screen.
=> Switch the <Smoothing> setting.

Select the suitable level 1-5 (Soft-Sharp).
Select <Smoothing> in the <Screen> menu and adjust by using the Right and Left
buttons.

* <Smoothing> is disabled when the screen is displayed in the following

resolutions.

● 1280 x 1024

● The image size is doubled both in horizontally and vertially to (i.e. 1280

x 960 enlarged from 640 x 480) provide clear focus which does not
require this function.

3.Set the brightness of the black area surrounding the displayed
image.
=> Set the <Border Intensity>.

In the "Enlarge" mode or "Full Screen" mode, the outer area (border) is usually black.
Select <Border Intensity> in the <Others> menu and adjust by using the Right and Left
buttons.

Color settings of each FineContrast mode can be adjusted and saved by using the
<Color> menu of the ScreenManager.

In the analog input, perform the <Range Adjustment> before making the
color adjustments.

Adjustment Items

The adjustable items and displayed icons on the <Color> menu depend on the selected
FineContrast mode.

"*": Settable/Adjustable "-": Fixed at the factory

Icons Functions

Brightness** * *
Temperature**

Gamma**

Saturation
Hue

Gain
6 colors

Reset

**These settings can be also adjusted on the FineContrast menu.

FineContrast Modes

sRGB Custom CAL

-

-

-

*
*

-

-

-

-

-

*
*

*

-

-

-

-

-

*
*

-

-

* Allow the LCD monitor to stabilize for at least 20 minutes before making image

adjustments. (Allow the monitor to warm Up for at least 20 minutes before
making adjustments.)

* Performing the <Reset> of the <Color> menu returns the color settings of the

selected mode to the default settings.

* The values shown in percentages represent the current level within the specific

adjustment. They are available only as a reference tool. (To create a uniform
white or black acreen, the percentages for each will probably not be the same.)

Adjustment Contents

Menu Function Descriptions Adjustable Range

Brightness

To set the brightness of the
screen

0 ~ 100%

Temperature

To set the color temperature 4,000 ~ 10,000 K

in 500 K increments (including 9,300
K). Default setting is 5,000K

The values shown in the Kelvin are available only as a

*

reference tool.
Adjusting the <Gain> turns the <Temperature> adjustement

*

"OFF".
Setting the temperature under 4,000 K or over 10,000 K

*

invalidates the color temperature setting. (The color
temperature's setting turns "OFF".)

Gamma To set the gamma value 1.8 ~ 2.6 (in 0.2 increments)

* If setting the gamma value, the using the monitor in the

digital signal input is recommended.
If using the monitor in the analog input signal, set the gamma
value from 1.8 to 2.2.

Saturation

Hue

Gain

To change the saturation -16 ~ 16

Setting the minimum level (-16)
turns the image to the monochrome.

The <Saturation> adjustment may cause undisplayable color

*

tone.

To change the flesh color, etc. -20 ~ 20

The <Hue> adjustment may cause undisplayable color tone.

*

To change each color (red,
green and blue)

The values shown in the percentage are available only as a

*

reference tool.
Setting the <Temperature> invalidates the <Gain>

*

adjustment. <Gain> setting returns to the default setting.

0 ~ 100%
By adjusting the red, green and blue
color tones for each mode, custom
colors can be defined. Display a
white or gray background image and
adjust the <Gain>.

6 colors

Reset

To adjust <Saturation> and
<Hue> in each color (Red,
Yellow, Green, Cyan, Blue
and Magenta)

To return the color settings of
the selected mode to the
default settings

Hue: -20 ~ 20
Saturation: -16 ~ 16

Select the <Reset>.

The <PowerManager> menu in the ScreenManager enables to set the power-save setup.

* Do your part to conserve energy, turn off the monitor when you are finished

using it. Disconnecting the monitor from the power supply is recommended to
save energy completely.

* Even if the monitor is in a power saving mode, USB compliant devices function

when they are connected to the monitor's USB (both the Upstream and the
Downstream ports). Therefore, power consumption of the monitor will change
according to the connected devices even if the monitor is in a power saving mode.

Analog Input

This monitor complies with the "VESA DPMS" standard.

To use the PC's Power Saving System (VESA DPMS).

[Procedure]

(1) Set the PC's power saving settings.
(2) Select "VESA DPMS" in the <PowerManager> menu.

[Power saving system]

PC Monitor Power Indicator

Operation Operation Blue

Power saving

STAND-BY
SUSPEND OFF

Power saving Yellow

[Power Resumption Procedure]

Operate the mouse or keyboard to return to a normal screen.

Digital Input

This monitor complies with the "DVI DMPM".

[Procedure]

(1) Set the PC's power saving settings.
(2) Select "DVI DMPM" from the <PowerManager> menu.

[Power saving system]

PC Monitor Power Indicator

Operation Operation Blue

Power saving Power saving Yellow

Off mode Power saving*1

*1 Power saving through the PC's off mode is only supported when "Manual" is

selected on the ScreenManager's <Input Priority>.

[Power Resumption Procedure]

Operate the mouse or keyboard to return to a normal screen .
Power on the PC to return a normal screen from the Off mode of the PC.

Flashing yellow

(2 times for each)

This monitor provides a hub which supports the USB standard. When connecting to a
USB compliant PC or another hub, the monitor functions as a hub which the USB
compliant peripherals can be easily connected.

Required System Environment

* PC equipped with USB ports or another USB hub connected to the USB

compliant PC
* Windows 98/2000/XP//Mac OS 8.5.1 or later
* EIZO USB Cable (MD-C93, enclosed)

* The USB hub function may not work properly depending on the PC, OS or

peripherals. Please consult the manufacturer of each device about the USB

support.
* Using the USB Rev . 2.0 compatible PC or peripherals is recommended.
* When the monitor is not on, the peripherals connected to the downstream ports

will not operate.
* Even if the monitor is in a power saving mode, the devices connected to the

monitor's USB ports (both the upstream and the downstream) will function.
* The followings are procedures for the Windows 98/Me/2000/XP and Mac OS.

Connecting to the HUB USB

1.Connect the monitor to the PC with the signal cable first, then turn
on the PC.

2.Connect the upstream port of the monitor to the downstream port
of the USB compliant PC or another hub by using the USB cable.

After connecting the USB cable, the USB function can be set up automatically.

3.After setting up, the monitor's USB hub is available for connecting
USB compliant peripherals to the downstream ports of the monitor.

Connecting Examples

If a problem persists even after applying the suggested remedies, contact an EIZO
dealer.

● No picture problems : See No.1 ~ No.2

● Imaging problems : See No.3 ~ No.14

● Other problems : See No.15 ~ No.18

● USB problems : See No.19 ~ No.20

Problems Points to check with possible solutions

1. No picture

[ ] Check that the power cord is correctly

connected. If the problem persists, turn off

Indicator status: Off

the monitor power for a few minutes, then
turn it back on and try again.

Indicator status: Blue

[ ] Check the Brightness setting.

Indicator status: Yellow [ ] Switch the signal Input by pressing the input

signal selection button on the front control
panel.

[ ] Try pressing a key on the keyboard, or

clicking the mouse.

Indicator status: Slowly flashing

[ ] Try pressing the power button

Yellow

Indicator status: Flashing Yellow

[ ] Try turning the PC on.

(twice for each)

2. Following messages
appear. (Error messages
shown below will remain
on the screen for 40
seconds.)

These messages appear when the signal is not
inputted correctly, even if the monitor
functions properly.

[ ] When the image is displayed correctly after a

short time, there is no problem with the
monitor. (Some PCs do not output the signal

soon after powering on.)
[ ] Check that the PC is turned ON.
[ ] Check that the signal cable is properly

connected the PC or graphics board.
[ ] Switch the signal input by pressing the Input

Signal Selection button on the front control

panel.

Whenever an error signal
message appears, the signal
frequency will be displayed in
red. (Example)

[ ] Use the graphics board's utility software to

change the frequency setting. (Refer to the

manual of the graphics board.)

3. Display position is
incorrect.

4. Screen image is smaller
or larger than the actual
screen images.

5. Vertical bars of distortion
appear.

[ ] Adjust the image position using the

<Position>.

[ ] If the problem persists, use the graphics

board's utility software to change the display
position if available.

[ ] Adjust the resolution using the <Resolution>.

[ ] Decrease the vertical bars using the <Clock>.

6. The characters and
images have several
vertical bars on their right
side.

[ ] Adjust the characters and images using the

<Signal Filter>.

7. Horizontal bars of
distortion appear.

[ ] Decrease the horizontal bars using the

<Phase>.

8. Letters and lines appear
blurred.

9. Distortion appears like the
figure below.

10.The screen is too bright
or too dark.

11.Afterimages appear.

[ ] Adjust the blurred lines using <Smoothing>.

[ ] This happends when both composite (X-OR)

input signal and separate vertical
synchronizing signal are input. Please select
one of the two.

[ ] Adjust the <Brightness> (The backlight of

the LCD monitor has a fixed life span. When
the screen becomes dark or begins to flicker,
please consult your dealer.)

[ ] When the screen image is changed after

displaying the same image for a long period,
an afterimage may appear. The "Afterimage"
can be removed gradually by changing the
displayed image. Use the <Off Timer>

12.The screen has defective
pixels (e.g. slightly light
or dark).

13.Fingerprints remain on
the screen.

14.The noise appears on the
screen.

function and avoid keeping the screen on all
the time.

[ ] This is due to the characteristics of the panel

itself, and not the LCD product.

[ ] Leaving the screen white may solve the

problem.

[ ] Change the mode in <Signal Filter> in the

<Screen> menu.

15.The <Smoothing> cannot
be selected.

[ ] <Smoothing> is disabled when the screen is

displayed in the 1280 x 1024.

[ ] <Smoothing> is disabled when "Normal" is

selected in the <Screen Size> menu.

[ ] The image size is doubled both in

horizontally and vertically to (i.e. 1280 x 960
enlarged from 640 x 480) provide clear focus
which does not require this function.

16.The Main menu of
ScreenManager does not
operate.

17.The Auto adjustment
button does not operate.

18.Frequency does not
change after installing
"Monitor information file"
in the attached utility disk
on Windows 98/Me/2000/
XP.

19.USB function cannot be
setup.

[ ] The adjustment lock is probably on. To

unlock: switch the LCD monitor off. Then,

while pressing the Autadjustment button
switch, the power on.

[ ] The adjustment lock is probably on. To

unlock: switch the LCD monitor off. Then,
while pressing the Auto adjustment button,
switch the power on.

[ ] Use the graphics board's utility software to

change the input signal frequency.

[ ] Check that the USB cable is correctly

connected.

[ ] Check that the PC and OS are USB

compliant. (For verification of USB support,
consult the manufacturer of each system.)

[ ] Check the PC's BIOS setting for USB. ( For

details, refer to the manual of the PC.)

20.PC is hung up. / The
peripherals connected to
the downstream ports do
not operate.

[ ] Check that the USB cable is correctly

connected.

[ ] Check the downstream ports by connecting

the peripherals to other downstream ports. If
the problem is solved by doing this, contact
an EIZO dealer. (For details, refer to the
manual of the PC.)

[ ] Try executing the following method.

● Restarting the PC - Restarting the PC

● Connecting the PC and peripherals

directly

If the problem is solved by doing this,
contact an EIZO dealer.

Periodic cleaning is recommended to keep the monitor looking new and to prolong its
operation lifetime.

* Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol),

abrasive cleaners, or other strong solvents, as these may cause damage to the
cabinet or LCD panel.

Cabinet

To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild
detergent. Do not spray wax or cleaner directly into the cabinet. (For details, refer to
the manual of the PC.)

LCD Panel

● The LCD surface can be cleaned with a soft cloth, such as cotton or lens paper.

● If necessary, stubborn stains can be removed by moistening part of a cloth with

water to enhance its cleaning power.

48 cm (19.0 inch), TFT color LCD panel with Anti-Glare Hard

LCD Panel

Dot Pitch 0.294 mm

Coating
Viewing Angle: H: 170°, V: 170° (CR>10)

Horizontal Scan
Frequency

Vertical Scan
Frequency

Resolution 1280 dots x 1024 lines
Dot Clock (Max.) Analog: 135 MHz, Digital: 108 MHz
Display Colors 16 million colors (max.)

Display Area

Power Supply

Power
Consumption

Input Connector DVI-I x 2
Analog Input

Signal (Sync)

Analog: 30 - 82 kHz (Automatic)
Digital: 30 - 65 kHz

Analog: 49 - 86 Hz (Automatic)
(1280 x 1024: 49 - 75 Hz)
Digital: 59 Hz - 61Hz, (VGA Text : 69 - 71 Hz)

376 mm (H) x 301 mm (V) (14.8" (H) x 11.9" (V)) (Viewable
image size: 481 mm (19.0"))

100-120VAC±10% 50/60 Hz, 0.6A
200-240 VAC±10%, 50 Hz, 0.35 A

Min.: 54 W
Max: 60 W (With USB hub)
Power Saving Mode : Less than 3 W

a) Separate, TTL, Positive/Negative
b) Composite, TTL, Positive/Negative

Analog Input
Signal (Video)

Input Signal
(Digital)

Signal registration
Plug & Play VESA DDC 2B
Dimensions
Dimensions

(without stand)
Weight 8.1 kg (17.9 lbs.)
Weight (without

stand)

Temperature

USB standard Rev. 2.0 complied

0.7Vp-p/75 ohms, Positive

TMDS (Single Link)
Analog : 45 (Preset: 25)

Digital : 10 (Preset: 6)

414 mm (W) x 409.5 - 509.5 mm (H) x 202.7 mm (D)
(16.3"(W) x 16.1"- 20.1"(H) x 8.0"(D))

414 mm (W) x 340 mm (H) x 64 mm (D)
(16.3"(W) x 13.4"(H) x 2.52"(D))

5.8 kg (12.8 lbs.)
Operating: 0 °C - 35 °C (32 °F - 95 ° F)

Storage: -20 °C - 60 °C (-4 °F - 140 ° F)
Humidity 30% to 80% R.H. Non-condensing

Communication
speed

480Mbps(high), 12 Mbps (full), 1.5 Mbps (low)

Downstream
power supply

500 mA for each (Max.)

USB ports Upstream port x 1, Downstream port x 2
Certifications and

Standards
100-120 VAC

Certifications and
Standards
200-240 VAC

*1

Applicable to gray (standard) color version only.

*2

Applicable to black color version only.

NRTL/C-TÜV, FCC-B, TCO'03*1, TCO'99*2, EPA ENERGY
STAR Program, TÜV/Rheinland Ergonomics Approved

CE, CB, TÜV Rheinland/GS, TCO'03*1, TCO'99*2, EPA
ENERGY STAR Program, TÜV/Rheinland Ergonomics
Approved

Default settings

Analog input Digital input
Brightness 100% 100%
Smoothing 3
Temperature 5,000K
FineContrast Mode Custom
PowerManager VESA DPMS DVI DMPM
Screen Size Full
Input Priority Signal 1
Off Timer Disable

Menu Size Normal

Menu Settings

Menu Off Timer 45 seconds
Beep On
Language English
Input Selection Standard

Beeper settings

Short beep

ScreenManager item selected.
ScreenManager parameter adjusted to minimum or maximum
limit.
Input Signal Selection button pressed.

Long beep

4 short beeps

2 short beeps
every 15 sec.

Dimensions

Auto Adjustment button pressed.
ScreenManager data-save executed.

Monitor not connected correctly.
PC turned off.
Monitor received unsupported signal frequency.

Monitor is in the advance notice mode of the Off Timer. The
power will be off within fifteen minutes.

Unit mm (inches)

Pin Assignment

DVI-I Connector

Pin

No.

Signal

Pin

No.

Signal

Pin

No.

Signal

1 TMDS Data 2- 11

2 TMDS Data 2+ 12 NC 22

TMDS Data

3

2/4 Shield

4 NC* 14 +5V Power 24 TMDS Clock-

5 NC 15

DDC Clock

6

(SCL)
DDC Data

7

(SDA)

8

9 TMDS Data1- 19

Analog

Vertical Sync

TMDS Data

1/3 Shield

13 NC 23 TMDS Clock+

Ground

(return for

+5V, Hsync

and Vsync)

16

17 TMDS Data0- C3 Analog Blue

18 TMDS Data0+ C4

Hot Plug

Detect

TMDS

Data0/5 Shield

21 NC

TMDS Clock

Shield

C1 Analog Red

C2 Analog Green

Analog Horizontal

Sync

Analog Ground

C5

(analog R, G, & B

return)

10 TMDS Data1+ 20 NC

(*NC: No Connection)

USB Ports

No. Signal Signal

1 VCC Cable power
2 -Data Serial data
3 +Data Serial data
4 Ground Cable Ground

Afterimage

The Afterimage is particular to LCD monitors when the monitor screen is left on for a
long period without use. The "Afterimage" can be removed gradually by changing the
displayed image.

Clock

With the analog input signal display, the analog signal is converted to a digital signal
by the LCD circuitry. To convert the signal correctly, the LCD monitor needs to
produce the same number clock pulse as the dot clock of the graphics system. When
the clock pulse is not correctly set, some vertical bars of distortion are displayed on the
screen.

Color Temperature (Temperature)

Color Temperature is a method to measure the white color tone, generally indicated in
degrees Kelvin. At high temperatures the white tone appears somewhat blue, while at
lower temperatures it appears somewhat red. Computer monitors generally give best
performance at high temperature settings.

5,000 K: Slightly reddish white.
6,500 K: Warm-white tone, similar to white paper or daylight.
9,300 K: Slightly bluish white.

DVI (Digital Visual Interface)

A digital flat panel interface. DVI can transmit digital data from the PC directly
without loss with the signal transition method "TMDS".

There are two kinds of DVI connectors. One is DVI-D connector for digital signal
input only. The other is DVI-I connector for both digital and analog signal inputs.

DVI DMPM (DVI Digital Monitor Power Management)

The Power management system for the digital interface. The "Monitor ON" status
(operation mode) and the "Active Off" status (power-saving mode) are indispensable
for the DVI-DMPM as the monitor's power mode.

Gain Adjustment

Adjusts each color parameter for red, green and blue. The color of the LCD monitor is
displayed through the color filter of the LCD panel. Red, green and blue are the three
primary colors. The colors on the monitor are displayed by combining these three
colors. The color tone can change by adjusting the illumination amount passed through
each color's filter.

Gamma

Generally, the relationship that the light intensity values of a monitor change
nonlinearly to the input signal level is called "Gamma Characteristic". On the monitor,
low gamma values display the whitish images and high gamma values display the high
contrast images.

Phase

The phase adjustment decides the sampling timing point for converting the analog
input signal to a digital signal. Adjusting the phase after the clock adjustment will
produce a clear screen.

Range Adjustment

The Range Adjustment controls the level of output signal range to display the whole
color gradation.

Resolution

The LCD panel consists of a fixed number of pixel elements which are illuminated to
form the screen image. The EIZO CG19 display panel consists of 1280 horizontal
pixels and 1024 vertical pixels. At a resolution of 1280 x 1024, all pixels are displayed
as a full screen.

sRGB (Standard RGB)

"International Standard for Red, Green, and Blue color space" A color space was
defined with the aim of the color matching between applications and hardware devices,
such as monitors, scanners, printers and digital cameras. As a standard default space,
sRGB allows Internet users to closely match colors.

TMDS (Transition Minimized Differential Signaling)

A signal transition method for the digital interface.

VESA DPMS
(Video Electronics Standards Association - Display Power
Management Signaling)

The acronym VESA stands for "Video Electronics Standards Association", and DPMS
stands for "Display Power Management Signaling". DPMS is a communication
standard that PCs and graphics boards use to implement power savings on the monitor
side.

Preset Timing Chart for Analog input
Timing-Übersichten für Analog Eingang
Synchronisation des Signaux pour Analog numerique

Based on the signal diagram shown below 25 factory presets have been registered in
the monitor's microprocessor.

Der integrierte Mikroprozessor des Monitors unterstützt 25 werkseitige
Standardeinstellungen (siehe hierzu die nachfolgenden Diagramme).

25 signaux ont été enregistrés en usine dans le microprocesseur du moniteur,
conformément au diagramme de synchronisation ci-dessous.

Mode
VGA

640×480

Dot Clock Sync Polarity Frequencies

MHz H V fH: kHz fV: Hz

25.2 MHz

VESA
640×480

31.5 MHz Nega Nega 37.5 75.0

VESA
640×480

VESA
800×600

VESA
800×600

VESA
800×600

VESA
800×600

VESA
800×600

VESA
1024×768

VESA
1024×768

VESA
1024×768

36.0 MHz Nega Nega 43.3 85.0

36.0 MHz Posi Posi 35.2 56.3

40.0 MHz Posi Posi 37.9 60.3

50.0 MHz Posi Posi 48.1 72.2

49.5 MHz Posi Posi 46.9 75. 0

56.3 MHz Posi Posi 53.7 85.1

65.0 MHz Nega Nega 48.4 60.0

75.0 MHz Nega Nega 56.5 70.1

78.8 MHz Posi Posi 60.0 75.0

VESA
1024×768

VESA
1152×864

VESA
1280×960

VESA
1280×1024

VESA
1280×1024

94.5 MHz Posi Posi 68.7 85.0

108.0 MHz Posi Posi 67.5 75.0

108.0 MHz Posi Posi 60.0 60.0

108.0 MHz Posi Posi 64.0 60.0

135.0 MHz Posi Posi 80.0 75.0

[Applicable to gray cabinet.]

Congratulations!

The display you have just purchased carries the
TCO'03 Displays label. This means that your display
is designed, manufactured and tested according to

some of the strictest quality and environmental
requirements in the world. This makes for a high performance product,
designed with the user in focus that also minimizes the Impact on our
natural environment.

Some of the features of the TCO'03 Display requirements:

Ergonomics

Good visual ergonomics and image quality in order to improve the working
environment for the user and to reduce sight and strain problems. Important
parameters are luminance, contrast, resolution, reflectance, colour rendition
and image stability.

Energy

● Energy-saving mode after a certain time - beneficial both for the

user and environment

● Electrical safety

Emissions

● Electromagnetic fields

● Noise emissions

Ecology

● The products must be prepared for recycling and the manufacturer

must have a certified environmental management system such as
EMAS or ISO 14000

● Restrictions on
❍ chlorinated and brominated flame retardants and polymers

❍ heavy metals such as cadium, mercury and lead.

The requirements includes in this label have been developed by TCO
Development in co-operation with scientists, experts, users as well as
manufacturers all over the world. Since the end of the 1980s TCO has been
involved in influencing the development of IT equipment in a more user­friendly direction. Our labeling system with displays in 1992 and is now
requested by users and IT-manufacturers all over the world.

For more information, please visit

www.tcodevelopment.com

Hinweis zur Ergonomie

Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB 2000 mit
dem Videosignal, 1280 Punkte X 1024 Zeilen, RGB analog, 0,7 Vp-p und mindestens
75,0 Hz Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen
Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu
verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem
Zeichenkontrast.)

Recycle Auskunft

Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in
Deutschland zusammen mit dem Partner von Roll MBB Recycling GmbH. Dort
werden die Geräte in ihre Bestandteile zerlegt, die dann der Wiederverwertung
zugeführt werden. Um einen Abholtermin zu vereinbaren und die aktuellen Kosten zu
erfahren, benutzen Sie bitte folgende Rufnummer: 02153-73 35 00. Weitere
Informationen finden Sie auch unter der Internet-Adresse: www.eizo.de.

Recycling Information for customers in Switzerland:

All recycling information is placed in the SWICO's website.

http://www.swico.ch

Recycling-Informationen für Kunden in der Schweiz:

Alle Informationen zum Thema Recycling finden Sie auf der Homepage des
Branchenverbandes SWICO.

http://www.swico.ch

Renseignements de recyclage pour les clients en Suisse:

Vous trouvez tous les renseignements pour le sujet de recyclage sur la page WEB de
l'UNION DE BRANC HE SWICO.

http://www.swico.ch

Recycling Information for customers in USA:

All recycling information is placed in the Eizo Nanao Technologies, Inc.'s website.

http://www.eizo.com/contact/index.html

Återvinnings information för kunder i Sverige:

All information om återvinning finns på Eizo Nordics hemsida:

www.eizo.se

Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor

Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum
Standardzubehör gehörige Schwenkarm verwendet wird, muss statt dessen ein
geeigneter anderer Schwenkarm installiert werden. Bei der Auswahl des Schwenkarms
sind die nachstehenden Hinweise zu berücksichtigen:

Der Standfuß muß den nachfolgenden Anforderungen entsprechen:

a) Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des

Gewichtes vom Bildschirmgerät und des spezifizierten Zubehörs besitzen. Das
Gewicht des Bildschirmgerätes und des Zubehörs sind in der zugehörenden
Bedienungsanleitung angegeben.

b) Die Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der

Bildschirmanzeige nicht höher als die Augenhöhe eines Benutzers in sitzender
Position ist.

c) Im Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes

derart erfolgen, daß die Höhe der Bildschirmmitte über dem Boden zwischen
135 - 150 cm beträgt.

d) Der Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen

(max. vorwärts: 5°, min. nach hinten =/> 5°)

e) Der Standfuß muß die Möglichkeit zur Drehung des Bildschirmgerätes besitzen

(max. ± 180°). Der maximale Kraftaufwand dafür muß weniger als 100 N

betragen.
f) Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.
g) Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen

(seidenmatt).
h) Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der

normalen aufrechten Position kippsicher sein.